Search Documents

By Adrian J. Mathias

This report presents the results of an investigation of a mine production-scheduling model and a critical path analysis for long-range mine planning. An example is given to illustrate how these techniques might be used to plan long-range development and production scheduling for a large underground mine. The model, based on estimated ore block grades and tonnages, and on designed mine development layout, simulates mining of ore blocks in a sequence necessary to fulfill mill requirements for ore tonnage and grade evaluation within pre-established system restrictions. Simulated production schedules are obtained as output from the model. These production schedules are then incorporated into a critical path analysis to determine the sequence for the long-range development work so as to fulfill the production schedules and thereby meet the ore grade and tonnage requirements of the mill.

Jan 1, 1967

By Leonard Obert

THE CRACKING AND POPPING of rock, often heard by men working underground, for years has been interpreted as a warning of danger and unstable ground. However, not until 1939 was it discovered that rock under stress generates subaudible and sometimes audible seismic disturbances (referred to as "micro-seismims" 4), which can be detected with the use of a suitable seismic apparatus. Since that date laboratory and field investigations have been in progress to ascertain to what extent this phenomenon can be utilized to detect, localize, and determine the magnitude of areas of instability in and around mine openings and to predict if and when failure will occur. These investigations have included a determination of the types of problems to which the method is applicable and the effect of rock type, geological defects, such as joints, fractures, faults, and other uncontrollable factors, on the reliability of results. Six reports have been prepared covering the investigations conducted between 1940 and 1952 (4-9). 5 These reports describe some of the characteristics of micro-seismims, as determined from both laboratory and field tests; the equipment used to pick up and record micro-seismims; the general test procedure and method of analyzing results; and applications of the method to specific mining problems.

Jan 1, 1957

By Homer J. Ballinger

The Alma, Degraff and other mines controlled by the Mon-Ark Mining Co. comprise one of the more important groups of zinc-lead mines in Christian County, Mo. The mines were first operated in .1857 and produced more than 5 million pounds of lead from rich, shallow ore deposits. Recent exploration and development led to the discovery of zinc sulfide ore at a depth of 165 to 214 feet in the northern part of the Alma mine. After examination of these mines in September 1942 by Bureau of Mines engineers, investigation of the extension -of the Alma mine and of the depth of mineralization at the other mines appeared justified in order to encourage the production of additional zinc and lead for war purposes. Twenty-nine churn-drill holes totaling 6.463 feet of bore were completed by the. Bureau from September 1943 to January 1944.

Jan 1, 1948

By Martin D. Conyac

A mineral resource survey of rock types and geologic structures indicates that the Mt. Henry RARE II area has low potential for the discovery of metallic minerals. Potential for coal and geothermal resources is negligible. Essentially, the Mt. Henry RARE II area has had no claim-staking activity, nor has any mine been developed in it. SETTING Size and Location The 23,000-acre (9,308 ha) "1t. Henry RARE II area (No. 1-666) lies within the Kootenai National Forest approximately 36 mi (58 km) north of Libby, Montana, in the Purcell Mountain; of Lincoln County. Irregularly shaped, the area measures roughly 5-1/2 mi (8.9 km) north-south by 8 mi (12.9 km) Past-west, and lies about 1-1/2 mi (7.2 km) south of the Canadian border.

Jan 1, 1982

By Alan A. Campoli

OD March 20, 1989, a meeting was held at the U.S. Bureau of Mines Pittsburgh Research Center at the request of Senator Pete V. Domenici of New Mexico. The purpose of the meeting was to engender a technical relationship between the National Laboratories and the minerals industry. During the meeting, the Director of the Bureau of Mines, T S Ary, suggested that since the Bureau is the focal point for mining research in the United States, it would be appropriate for the agency to act as the liaison between the National Laboratories and the minerals industry. As the first step in this process, the author was selected to perform a 6-month investigation to better define the proper role of the Bureau in this area. As part of the investigation, the mining and mineral-related technology available at 21 major U.S. Department of Energy (DOE) Research Laboratories was reviewed. It was assumed that the broad range of scientific and technical areas covered DOE research would provide fertile ground for mining-related technologies. It was hoped that the applicability of DOE research to this liaison effort would be indicative of Federal laboratories in general.

Jan 1, 2011

By W. E. Lamont

The Federal Bureau of Mines, in cooperation with phosphate companies in the Florida land-pebble area, made a comprehensive study of the waste clays, or "phosphate slimes," produced in the mining of phosphate rock in Florida. These slimes represent a significant ecological problem and a major deterrent to effective land recovery in the phosphate-mining areas. Physical, chemical, and mineralogical studies were made of slime samples submitted by 15 of the 16 plants in Florida in an effort to identify factors that prevent successful consolidation of the slimes and subsequent recovery of the mined lands. Results of these studies indicated that the clay mineral attapulgite, a hydrated magnesium silicate, was primarily responsible for the very poor settling characteristics of the slimes, and that the quantity of attapulgite in the slimes effectively controlled the settling rate, pulp density of terminal solids, viscosity, percent solids of filter cake, and flocculant requirements.

Jan 1, 1975

By Alan R. Buehler

A mineral survey of the 67, 110-acre Raven?s Eye WSA (Wilderness Study Area) in the north-central Snake River Plain of Idaho was conducted by the U.S. Bureau of Mines in 1985, at the request of the Bureau of Land Management. The WSA is in Blaine and Lincoln Counties; the northwest corner is about 1 mile east of Carey, 10. A search of county mining claim records indicated that no claims have been located in the WSA. Basaltic lava is the only rock type exposed within the WSA. A platy variety of lava (slab pahoehoe) occurs that is produced from other lava fields in southern Idaho. The material is marketed as decorative stone, used for wall veneers, and retails for approximately $125/ton. Within the W5A, approximately 18,000 tons of indicated reserves are concentrated in two areas, and a total of 12,000 tons of indicated subeconomic resources were found at six other localities. An additional 10,000 tons of inferred subeconomic resources are unevenly distributed over the remainder of the WSA.

Jan 1, 1986

By Edward F. Courtney

Loss of life, loss of sight, crippling injuries, and property damage nearly always result from accidents involving explosives. The severity of such accidents has prompted lawmaking bodies to pass laws concerning the transportation, handling, and use of explosives; manufacturers of explosives publish manuals 'describing explosives and practical methods of handling then; and mining companies and others who use large quantities of explosives publish rules based on actual experience for the guidance of their employees. Careless storage of explosives by thoughtless or incompetent persons, particularly if they are left where children or saboteurs have access 'to them, has led to many serious accidents. Many contractors and mining operators who use explosives are extremely careless about storing them. It is the purpose of this paper to discuss the explosive-handling practices of a large western mining company, which are considered better than most.

Jan 1, 1946

By Henry M. Harris, John E. Kelley, Thomas D. Roberts

A penetrometer apparatus for measuring viscosity of glass at temperatures up to 1,450 ° C was developed for use in establishing the viscosity coefficients required for high- temperature forming of ceramic materials . The major advantage of the method is that it can be used with samples of almost any shape or size without the necessity of forming or measuring shapes to close dimensional tolerances . Also , it has proved accurate in the range of 106 to 109 poises , a gap between the normal limits of other methods . The device , which operates on a single penetrometer principle , was used to determine the absolute viscosity coefficient of substances in centimeter - gram- second units of poises instead of relative penetration - rate units as with other penetrometers . Penetration of the viscous sample was sensed with a linear , variable differential transformer . The output of this transformer was recorded versus time , and the penetration rate was used in calculating the viscosity coefficient . The general equation relating penetration rate and viscosity coefficient was found to be 11 = F ( ln L/a 0.72 ) 2 π UL · where is the viscosity coefficient in poises , F is the penetrator load in dynes , L is the penetration depth in centimeters, a is the penetrator radius in centimeters and U is the penetration rate in centimeters per second . The penetrometer was tested using a standard viscosity sample of sodalime - silica glass obtained from the National Bureau of Standards ( NBS ) . Values obtained at several temperatures all agreed within 10 percent with comparable data calculated from the Fulcher equation derived by NBS for this glass . Equivalent accuracy was obtained with other glasses used to evaluate the apparatus .

Jan 1, 1964

By G. L. Oldright

[Processes by which silver alone is extracted from ores that also cant contain base metals are usually associated in the mind of the period when mines were changing from the production of noble metals to the production of base metals containing noble metals as a by-product. In this transition period the mixed arcs of the partly oxidized ore zone had to be treated instead of the free-milling ore that had been treated in the past or the deeper-lying sulphide ores that were to be smelted subsequently under improved economic and technical conditions.]

Jan 1, 1929

By Edward L. McHugh

In 1984, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied an 84,165-acre portion of the 84,935-acre Clover Mountains Wilderness Study Area (NV-050-139) in order to evaluates its identified mineral resources. The area studied is in Lincoln County, NV, about 90 miles north of Las Vegas, NV. No mineral resources were identified in the study area. Volcanic rocks are the most common in the study area, consisting mainly of a thick sequence of ignimbrites in a cauldron complex. Cambrian to Triassic marine sedimentary rocks and Cretaceous to Oligocene clastic rocks are along and partly inside the west and south sides of the study area. No mineral production ha s come from the study area, but gold, silver, copper, and fluorspar have been mined nearby. Eleven mines and prospects in or adjacent to the study area were examined. Workings inside the study area include two shafts, 10 and 60 ft deep, and eleven shallow prospect pits at four sites along the west edge.

Jan 1, 1987

By Thomas M. Barczak

The transverse loading requirement for stoppings as specified in the current Code of Federal Regulations is 39 psf. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where the dominant parameter is the tensile strength of the sealant. A new protocol based on arching has been developed to determine the true transverse load capacity of stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid-arching of stoppings was developed and verified through full-scale in-mine tests. Using this protocol, a systematic study of the design parameters that affect arching capability in block stoppings was conducted. The study included a theoretical assessment of arching and development of design formulations that can accurately define the transverse load capacity of various stopping constructions under various loading conditions. This approach should lead to a safer mine environment by matching the transverse load capabilities of the stopping design to the requirements in the mine to ensure proper ventilation control is maintained.

Jan 1, 2005

By D. H. Platt

Data obtained from on-the-site observations have been compiled to describe the equipment and installation methods used for satisfactory suspension roof support in a large-diameter tunnel. Experimental roof bolting was undertaken from June 1950 until May 8, 1951, in the East Delaware tunnel, which is part of the Delaware aqueduct in Delaware and Sullivan Counties, N. Y. Revised suspension-roof-support plans and specifications were prepared during the spring of 1951 by the City of New York Board of Water Supply; these were approved by the State of New York Department of Labor April 13, 1951, and adopted by the City of New York Board of Water Supply on May 8, 1951.

Jan 1, 1952

By Robert C. Johnson

Domestic byproduct fluorine (in fluosilicic acid) availability at various price levels of aluminum fluoride were determined and a contingency availability curve developed. The supply of byproduct fluosilicic acid is restricted in amount to certain geographic regions, where plants processing phosphate rock are located, and the byproduct can be collected. The maximum possible U.S. annual supply, based on potential plant capacities, is 373,400 tons of fluosilicic acid containing 295,400 tons of fluorine. Based on inputs of 5, la, 25, 50, and 100 thousand tons per year, five levels of producing aluminum fluoride from fluosilicic acid (100 percent) were costed. Based on a 12-percent discounted cash flow rate, including the cost of salvaging the fluosilicic acid, the calculated selling price of aluminum fluoride ranged from $233 per ton to $448 per ton. At the higher price, 98 percent of the potential supply of byproduct fluosilicic acid could be used profitably; at the lower price only 46 percent could be used profitably.

Jan 1, 1973

By Louis C. Srichta

The rapid depletion of known high-grade ore deposits of the Tri-State district and the recognized need for development of additional reserves, together with increased interest in open-pit mining of low-grade zinc-lead ores led to Bureau of Mines examination of several abandoned mining areas for possible deposits adapted to strip mining. Examination of the North Empire tract in Cherokee County, suggested that mineralized zones contiguous to previously mined 2e deposits presented probabilities of meeting the requirements for an open-pit mine - hence the tract was selected for further investigation by churn drilling. The zinc-lead deposit on the property is in a sink-hole structure that has been subjected to intense deformation and silicification. Numerous shafts, mine dumps, and surface caves are evidences of exploitation of an extensive area. The reported active mining period was 1895 to 1905. No production records are available, but it is generally stated locally that the value of the mill products exceeded $2,000,000 which represents considerable production, considering the low metal prices of that epoch.

Jan 1, 1950

By W. W. Weller

Heat capacity measurements of anhydrous cobalt sulfate (CoSO4), copper sulfate (CuSO4), nickel sulfate (NiSO4), and zinc sulfate (ZnSO4) were conducted over the temperature range 51° to 298° K. The results were used to evaluate the following entropies at 298.15° K (cal/deg mole): CoSO4, 28.1; CuSO4, 26.8; NiSO4, 24.8; and ZnSO4, 26.4. Entropies were combined with heats of formation to give free energies of formation.

Jan 1, 1965

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered transportation equipment approved or certified by the Bureau of Mines f r use in gassy noncoal mines and tunnels. Testing of diesel-powered equipment is one phase of the Bureau's health and safety program of approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, and toxic hazards in underground mines. In mines such equipment must be used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study f their design and safety features. Equipment must pass exacting tests and meet strict requirements established through research, development, and experience before the Bureau approves it as permissible for safe use in mines.

Jan 1, 1967

By Lawrence K. Requa

The property being worked by the Lewiston dredge of Placer Development (Ltd.) is on the Trinity River in Trinity County, Calif., about 9 miles north of the town of Lewiston (see fig. 1). The nearest rail point is at Rending, Calif., which is exactly 50 miles bar road from the dredge camp. Recently a very good section of State highway has been constructed from Redding to Weaverville, and it is now possible to use this highway for 35 miles of the distance between the dredging property and Redding. The remaining 15 miles, however, are over ordinary dirt road. No trouble is experienced in reaching the property except for a few weeks during the middle of the winter when snowstorms may make travel difficult but not impossible. At present the property consists of about 500 acres of patented land, which extends for about 3 miles along the main Trinity River and Stuart's Pork. It is being worked with one 7-cubic foot, Bucyrus-type dredge, which has an average monthly capacity of about 100,000 cubic yards. To the end of 1931 approximately 10,000,000 cubic yards of gravel had been dredged.

Jan 1, 1932

By W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil, this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states. Information given on each heavy-oil deposit includes the following items: Field and formation, location, average or range of depth, average API gravity of oil, aver- age thickness of formation, areal extent of field, total productive wells drilled in field, discovery date of field, field status in 1963, cumulative production to Jan. 1, 1964, and all known types of secondary-recovery operations initiated (active and terminated) Fn the reservoirs. The geographical location of heavy oil accumulations in the United States is shown by a map, and a brief discussion of 14 different areas is given in the text. As of Jan. 1, 1964, 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place. It is also estimated that if the deposits which have had little or no production history, such as the one in Missouri, were included, the total remaining heavy oil in place would be in excess of 150 billion barrels. To find economical ways of recovering this vast reserve of heavy oil, industry is developing technology in several types of thermal-recovery methods. Some of the general considerations and more suitable limitations in selecting a prospect to study fur thermal-recovery techniques are: Lithology, depth, viscosity of reservoir fluids, gravity of oil, reservoir thickness, oil in place, and permeability and porosity.

Jan 1, 1965

By W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil, this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states. Information given on each heavy-oil deposit includes the following items: Field and formation, location, average or range of depth, average API gravity of oil, aver- age thickness of formation, areal extent of field, total productive wells drilled in field, discovery date of field, field status in 1963, cumulative production to Jan. 1, 1964, and all known types of secondary-recovery operations initiated (active and terminated) in the reservoirs. The geographical location of heavy oil accumulations in the United States is shown by a map, and a brief discussion of 14 different areas is given in the text. As of Jan. 1, 1964, 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place. It is also estimated that if the deposits which have had little or no production history, such as the one in Missouri, were included, the total remaining heavy oil in place would be in excess of 150 billion barrels. To find economical ways of recovering this vast reserve of heavy oil, industry is developing technology in several types of thermal-recovery methods. Some of the general considerations and more suitable limitations in selecting a prospect to study fur thermal-recovery techniques are: Lithology, depth, viscosity of reservoir fluids, gravity of oil, reservoir thickness, oil in place, and permeability and porosity.

Jan 1, 1965