Search Documents

By FREDERICK L. WARD

This paper , describing the operation of the Ward Sand and Gravel Co.'s plant at Oxford , Mich . , is one of a series being prepared for and published by the United States Bureau of Mines on methods and costs of mining and preparing sand and gravel throughout the United States . These papers are designed to disseminate technical information regarding the methods used . The cost tabulations represent local operating expenditures only and not total production costs . It is recognized that publication of total costs might in some instances cause embarrassment to individual producers as well as to the industry as a whole . On the other hand , operating costs are essential to the technical discussion and study of the methods employed . The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue . The plant described is a dredging operation with many unique features ; especially noteworthy are the mining of the sand and gravel with hydraulic jets operating on the principle of a water ejector , the unusual construction of the dredge and the self- unloading barges that tend it , the transportation of the sand and gravel to shore in barges instead of in pipe lines , the large storage capacity of the plant , and the fact that all material goes into storage before being shipped .

Jan 1, 1932

By Joseph J. Wallace

1. The investigation shows that there are two coal beds of major importance in Perry County from the standpoint of present production -Flag and Fire Clay -and two beds of minor importance -Haddix and Hindman. The Flag and Fire Clay beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 840 million short tons as of January 1, 1954. Of this total, 720 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, these should be added to the total estimated reserves.

Jan 1, 1954

By D. J. Parker

Before the various States began to enact workman's compensation laws accidents were considered inherent in many industries, and little or no effort was made to prevent or reduce them. The hazard was accepted by the employee with the job, and the avoidance of accidents by mental alertness or physical agility was largely his responsibility. After the employee had given evidence of enough skill inn performing his allotted task efficiently the responsibility of the employer apparently ceased with respect to the personal safety of the employee. However, following the enactment of workmen's compensation laws, at least two facts that had not before been fully appreciated soon became apparent: (1) The majority of accidents can be prevented if the management firmly determines to prevent them; (2) frog a monetary point of view alone accidents are decidedly expensive, both to employer and to employee. It is now evident that savings effected by conscientious safety effort add substantially to net profits of operation.

Jan 1, 1934

By J. William Ganser

This paper is one of a series being prepared by the U. S. Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically palled to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Fred Burkett, civil engineer, and F. O. Londrey, chief clerk, of the Trinity Portland Cement Co., for assistance in preparation of this paper, "The Geology of Dallas County. 1918," Bulletin 1818, Texas Geological Survey, Austin, Tex., by E. W. Shuler, was also freely consulted.

Jan 1, 1931

By E. Owens, R. Gudavalli, D. Wilder, T. Xia

As mechanical shock and vibration environments evolve, it is important to understand their potential effect on human operators. Human beings are sophisticated mechanisms comprised not only of passive components with mass, damping, and stiffness characteristics, but also of components that can actively affect apparent mass, stiffness, and damping. Because the lumbar spine can exhibit local, short-column buckling, stability of the human trunk depends on the responsiveness of the neuromuscular control system.1-2 We have been evaluating the ability of patients with back pain to respond to a series of sudden loads. We believe the results have implications for isolation design and standards development. Methods 153 patients, aged 21 to 55, presenting with back pain agreed to enroll in a research study that randomly assigned them to one of three treatment arms: high velocity low amplitude spinal manipulation, low velocity variable amplitude spinal manipulation, or wait for 2 weeks and then be randomized to one of the above groups. Response to sudden load testing was one of a battery of baseline evaluations performed upon entry into the study and prior to treatment. EMG electrodes were attached to the skin over the paraspinal muscles of the standing participant bilaterally 3 cm from midline at the L3 level. While standing upright on a force plate (Bertec), participants were fitted with a strap around their back and hooked to a load cell in front of their chest. An accelerometer was rigidly attached to the load cell. Impact was applied to the chest using a cord attached to a falling weight. The weight’s fall distance was varied between 9 and 13 inches to account for the size of the subject. The subject was blindfolded and wore headphones playing white noise to prevent cueing of when the weight was dropped to apply the load. Hence, although the participant knew a load was about to be applied, he or she did not know the instant it would occur. Just before the weight was dropped, a 4 second data collection process was started for the two EMG electrodes, load cell, accelerometer, and force plate. The load drop was repeated 6 times, at irregular intervals, over a period of 2 minutes. The raw data thus collected was reduced to obtain several values: 1) length of time from the pull on the harness to the beginning of the response of the left and right paraspinal muscles (LES, RES), 2) time and magnitude of the maximum response, 3) force and acceleration experienced at the chest, and 4) the time and magnitude of the center of pressure location (COP). A general linear model was used to evaluate the results. Results For the EMG data, of the 1,824 observations made, 90% of them indicated a response. Prior to the sudden load, resting muscle activity was different between left and right sides (p=0.0001) and between males and females (p=0.0001). Female subjects began to respond to the sudden load within 92 to 110 ms and males from 101 to 109 ms. Females exhibited more variation in starting

Jan 6, 2006

By R. W. Van Dolah, N. E. Hanna, F. C. Gibson

Measures that were taken to eliminate noise resulting from explosives work at the Bureau of Mines facility at Bruceton , Pa . , are described . A method for monitoring sound transmission characteristics of the atmosphere and control of the explosives testing is presented as a noise control measure that offered partial relief during the period in which the modifications were made . Design details of the replacement gallery , used for permissibility testing of explosives , and the modifications of four types of bombproofs are given . Operation of the closed facilities are completely satisfactory , and the noise problem has been entirely eliminated .

Jan 1, 1964

By Jeffrey Shawn Peterson

The testing procedures of the u.s. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break-flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2010

By Ronald B. Hollenbeck

The value of mineral production in Alabama continued to increase and reached a new high of $260 million, 3 percent above the previous high established in 1967. Record high values were reported for bentonite, crushed marble, lime, miscellaneous clay, portland cement, salt, sand and gravel, and scrap mica. The value of coal, total cement, petroleum, and stone accounted for 87 percent of the State's total value of mineral production. Alabama ranked second among the States in the production of bauxite and scrap mica and third in kaolin, masonry cement, and native asphalt.

Jan 1, 1970

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coals; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the fourth of a series of reports giving the results of studies by counties under phase (1) of the investigation. It covers Armstrong County, Pa., which comprises parts of the Foxburg, Clarion, Brookville, Kittanning, Bural Valley, Smicksburg, Freeport, Elders Ridge, and Indiana quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and more than 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside the outcrop were measured by planimeter on the base maps, Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By Neil J. Mansfield

Tool manufacturers are required to provide declarations of vibration emission values in order to sell their tools within Europe. To ensure that users can compare results obtained from different manufacturers, the declared values must be obtained using a methodology as specified in the relevant test code (such as in the ISO 8662 series of standards). In most cases, the vibration emission values obtained using test codes under-estimate the vibration that an operator will be exposed to when using the tool on a work-site. A further problem with manufacturers’ data is that usually only a single value is provided for a tool. This is despite many factors affecting the vibration emission, including inserted tool type, work piece, operator technique, tool condition. New improved test codes are in the process of being developed. In order to provide guidance to users on how to interpret manufacturers’ data, a Draft CEN Technical Report (Draft CEN/TR 15350 (2005)) was developed. Part of the CEN/TR provides multiplication factors for combinations of task and tool type. For example, data obtained from electrical hammer drills (tested according to EN 60745-2-6:2003) should be multiplied by 2, for hammering applications, in order to obtain an estimate of the vibration emission during work. In response to concerns from industry, the UK trade association OPERC have, in collaboration with hire companies and tool manufacturers, established a freely accessible online database of tool emission values based on independent tests carried out under simulated work-site conditions. This paper reports some of the data obtained from electrical hammer drills, highlighting the range of emission values that can be obtained for a tool. Data from many other tool types are also included in the database. Methods Tri-axial hand-arm vibration was measured at both handles of each of 19 electrical hammer drills, in accordance with ISO 5349-1 (2001). Each tool was measured with three experienced operators and at least 5 runs were completed for each operator. Tools were tested using a range of appropriate new bits from 4 to 40 mm diameter. The minimum number of bits for a tool was 3; the maximum number was 29. 146 tool / bit combinations are reported here, representing about 2200 individual 6-axis measurements. Operators were required to drill vertically into a concrete block with a compressive strength after 28 days of 40 N/mm². Two drills (1 and 15) were battery powered; others were powered using a 110V transformer supply.

Jan 6, 2006

By X. Chi, J. W. Griffith, C. L. Schengrund, J. Sabol

"Experiments were carried out to determine the long-term effect of instillation of 500 mg of generic bituminous, anthracite, quartz, or titanium dioxide (Ti02) dust on the composition of pulmonary surfactant. Dust was instilled in the caudal lobe of the right lungs of female pigtailed macaque monkeys (Macaca nemestrina). The composition of surfactant isolated from cell-free bronchoalveolar lavage (CF-BAL) samples obtained from right lungs (dust exposed) at various times over the following year was compared with that of surfactant isolated from CF-BAL from left lungs (dust free) . Little change was seen in the amount of surfactant-associated lipid phosphorus as a result of exposure to dust. Exposure to quartz, anthracite, or Ti02 dust induced a significant increase in the total amount of protein in the surfactant-enriched fraction. The relative amount of specific proteins was also altered: surfactant-associated protein A decreased, and the amount of the heavy and light chains of immunoglobulin molecules (identified by NHiterminal amino acid sequence analysis) increased. These changes were visible more than a year after instillation of quartz and at least 3 months after instillation of anthracite dust. Despite variation in the responses of the individual animals, the changes observed might serve as an indicator of the severity of the effect of exposure of the lung to mineral dust and/or to pathogens. IntroductionSurfactant is essential for normal pulmonary function and gas exchange. It functions to reduce surface tension and may help to prevent pulmonary edema [19] and to protect against infection [13]. The importance of surfactant to normal Jung function is illustrated by the fact that neonates lacking appropriate surfactant undergo respiratory distress and do not survive without clinical support."

Dec 1, 1996

By E. Morrice, R. D. Smith

Thermal expansion and electrical resistance measurements were made on cerium metal from 4° to 300° K. The apparatus developed , including a specimen holder and a cryostat system , are described along with the experimental techniques used in obtaining the measurements . The total linear thermal expansion Data at of 99.83 weight - percent cerium metal between 4 ° K and room temperature was 4.24 percent . The resistivity at 4° K was 7.0 x 10-6 ohm- centimeter . 4° K indicate a fundamental relationship between residual resistivity and purity of cerium metal . The effects of annealing and repeated thermal cycling on resistivity were determined .

Jan 1, 1964

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of new' water and reused 3.8 billion gallons for a total usage of 12.4 billion gallons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain thin high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ire near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand For new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements in the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By D. Gearhart

Full-scale tests are conducted on mine roof supports using protocols developed by the National Institute for Occupational Safety and Health (NIOSH) using the unique capabilities of the Mine Roof Simulator (MRS). These protocols simulate the loading conditions that the support will be exposed to in an underground mine to determine the performance capabilities and limitations of the support. Some tests are conducted with rigid boundary conditions, creating uniform contact and near ideal axial loading conditions. These tests are used to determine the ultimate performance potential of a support, including the strength, stiffness, and stability. For prop supports where stability is a critical design issue, tests are implemented to induce buckling by a modified end condition, eccentric contact, or biaxial loading. It is important to determine the cpacity of the support design when the support is subjected to unpredictable loading conditions. This paper examines the effect of end conditions and load profiles on prop support performance and applies a new analysis methodology based on eccentric loading to determine a factor of safety for load capacity. Recommendations for installation practices that minimize eccentricity and therefore preserve capacity are also provided.

By JOEL H. SWARTZ

During a series of resistivity measurements carried out in 1929 and 1930 a number of questions arose concerning the effect of topography on the character of the curves and the depths attained , the ratio of true depth to certain radii interpreted as representing depth , etc. To answer these questions it was decided to undertake a series of experimental investigations on artificial strata . It is the purpose of the present paper to present the results of the studies thus undertaken .

Feb 1, 1931

By Edmund Shaw

This paper is one of a series being prepared by the United states Bureau of Mines describing mining and milling methods and costs at industrial mineral plants throughout the United states. These papers are designed to disseminate technical information regarding the methods and equipment used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might, in many instances, cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention' of the reader? is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. P. J. Weisel, Inc., with office at La Habra and plant at Corona, Calif., is the only local company that produces sand for the Los Angeles glass factories, although silica sand for other purposes is produced in other parts of southern California and the adjacent portions of Nevada. The deposit at Corona consists of coarse sand imbedded in a whitish clay and differs greatly from the other deposits, which are fine-grained sandstone that must be crushed before it can be screened and washed. The preparation of Corona sand has to be thorough and includes grinding in tube mills, repeated washing and rinsing, removal of dust by air separation, and magnetic separation of iron and other minerals. This requires a plant with a complicated flow sheet. The first plant built did not make a. satisfactory glass sand, and many additions and changes were necessary. It is thought that the present flow sheet will remain substantially unchanged until a new plant is built. The design of a new plant would be simpler, but the process would be the same.

Jan 1, 1937

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

A concise country-by-country summary of the mineral industry of Africa is presented. Reserves, resources, role of the country in the world mineral supply, and developments in the mineral industries are reviewed. The data on each country are accompanied by a map showing mineral location and transportation facilities.

Jan 1, 1976

By G. S. Scott. R. L. Grant

Ammonium nitrate (NH4NO3), a white crystalline chemical compound composed of 35 percent nitrogen, 60 percent oxygen, and 5 percent hydrogen, has again attracted attention, due largely to the recent catastrophe on April 16 and 17, 1947, at Texas City, Tex. The fire and subsequent explosion on the steamship Ocean Liberty, outside the harbor of Brest, France, on July 28, 1947, has fur- ther increased the interest in the properties of ammonium nitrate. As a result of the Texas City disaster, several laboratories have undertaken research to determine more certainly what causes ammonium nitrate to detonate and under what circumstances. This is not the first time that ammonium nitrate has been involved in a disaster, and its properties reviewed from the standpoint of safety. The disaster at Oppau, Germany, in 1921, which involved an equimolec- ular mixture of ammonium nitrate and ammonium sulfate, prompted an intensive study in Europe and in America. In the United States the properties of am- monium nitrate are now of especial concern because very large quantites are being manufactured and shipped in interstate commerce and abroad. Many an- monium nitrate factories, which were built during the war, will manufacture increasing amounts of this compound for use as a fertilizer. It is the purpose of this report to present a brief summary and biblio- graphy of the published experimental facts about the properties and behavior of ammonium nitrate. The reader is referred to original publications for greater details of the investigative work, and for theoretical discussions. This report also includes a survey of ammonium nitrate fertilizer of the type involved in the Texas City explosions. In the past, authorities have not always agreed on the degree of hazard involved in the manufacture and handling of ammonium nitrate, as the following quotations from the literature indicate: Munroe (82) quoted the following from Turner's Chemistry (a book pub- lished in 1835): "When this salt is exposed to fire, it liquefies, emits aqueous vapor, dries and detonates." Berthelot (14) in his book, Explosives and Their Power, 1983, wrote: "Ammonium nitrate from the point of view of its volatility, and cn account of many considerations, may be regarded as a typical explosive substance."

Jun 1, 1948

By Wallace W. Roepke

Four bit designs, two conical and two radial, were tested in coal against a 60° conical reference bit to obtain data on orthogonal cutting forces and primary respirable dust generation. One conical and one radial design were modified by the Bureau of Mines for these tests. Results were mixed: One radial bit used substantially lower overall cutting forces and specific energy than the other bits and was the only cutter lower on energy and most forces than the standard 60° bit. How-ever, it generated more specific and total dust than any other bit. The four bits were also tested for incendivity, with a 90° plumb-bob bit as the reference. The frictional ignition tests were designed to simulate both trimming top rock and cutting such rock during advance on-sump. Results of these tests were also mixed. The radial bits were substantially less incendive than the reference bit and caused no ignitions in either top trimming or sump modes. Only the modified mushroom-tipped conical bit caused ignitions. Bits similar to this modified design should not be used on drum-type miners in gassy mine areas; in-stead, the other types of bits tested should be used to reduce ignition potential to a minimum.

Jan 1, 1983