Search Documents

By Jack Smith

New turbine blades designed to resist ash erosion were tested by the Bureau of Mines in a pilot-scale coal-fired gas turbine. After a total of 1,963 hours, the rotor blades were only slightly eroded; and they had an estimated useful life of 20,000 to 30,000 hours. Changes in aerodynamic design of the blades successfully concentrated the ash at the outer casing, but stepped sidewalls for the rotor drum and wear strips at the bases of the rotor blades are still needed to minimize wear at these points. Stepped sidewalls and wear strips did not adequately protect the stator blades. Ash slightly eroded their leading edges, above the inserts, and cut notches into their trailing edges near the bases. Stator blade life was estimated at 5,000 to 7,500 hours. Blade erosion in these tests was less severe than with previous designs, but more efficient combustors and ash separators are required to reduce the amount and size of ash entering the turbine, to achieve acceptable blade life for commercial operation.

Jan 1, 1967

By W. W. Agey

An inexpensive technique that laboratory studies indicated would significantly reduce seepage in irrigation canals was devised and tested through research sponsored by the Bureau of Reclamation and the Missouri River Basin Field Committee. Laboratory tests simulating optimum field conditions determined that easily applied sodium carbonate solutions made test beds of canal lining materials virtually impermeable for long periods. The study comprised alternative laboratory treatments of 3-inch-deep test beds of canal earths with 74 water-soluble chemicals in search of one 01' more that would effectively improve the water barrier characteristics of the component clays. Sodium carbonate, one of the least expensive, was among the most effective. The addition of 0,4 lb of reagent per sq yd greatly reduced the seepage from typical, highly permeable test beds. The reagent penetrated and sealed surface for about a 1.5-inch depth.

Jan 1, 1965

By E. L. Litchfield

Four short-term studies of practical ignition problems were undertaken and completed during the course of the Bureau of Mines project "Development of Specifications for Intrinsically Safe Equipment." Conclusions were as follows: (1) the most easily ignitible mixture of propane-air in a PTB break flash apparatus is approximately 5.2 percent propane; (2) miniature lamp bulbs to be used in intrinsically safe circuits are about as incendive to coal dust-air as to methane-air and should be tested in gas mixtures containing about 7.0 to 7.5 percent methane; (3) the sodium amalgam contained in high-pressure sodium lamps does not present an ignition hazard for coal dust or methane, where the lamps contain no more than 30 milligrams of amal-gam; (4) the maximum allowable surface temperature of permissible electrical enclosures should remain at 150° C despite efforts by industry groups to raise the value to 200° C.

Jan 1, 1980

By Forrest T. Moyer

All general measures of the safety record of the coal mining industry worsened appreciably in 1970. Injury experience for the year was 260 fatal and 11,552 nonfatal injuries at respective frequency rates of 1.00 and 44.40 per million man-hours of worktime. The fatality total was 57 higher and the rate of occurrence was 18 percent higher than the corresponding figures of 203 fatal injuries with a frequency rate of 0.85 in 1969. The worsened fatality record in 1970 resulted primarily from a major disaster (a single accident which results in the death of five men or more) on December 30, 1970, that killed 38 men. There were no major disasters in 1969. The total of 11,552 nonfatal injuries in 1970 was the highest annual total since 1960. It was 1,635 higher and the frequency rate was 6 percent higher than the corresponding totals for 1969 of 9,917 nonfatal injuries occurring at a rate of 41.76. The injury severity rate of 8,308 days lost or charged per million man-hours was 13 percent worse than that of 7,359 in 1969. Similarly, the average severity of 183 days lost or charged per injury in 1970 was 10 days or 6 percent higher than in 1969. Aggregate worktime of 260.2 million man-hours and production of 609.8 million tons in 1970 were, respectively, 10 and 7 percent higher than in 1969. An average of 144,480 men were at work on an average of 227 active days in 6,316 mines and 544 mechanical cleaning plants during 1970.

Jan 1, 1973

By S. H. Ash

A CLAY, sand, and gravel deposit known as the "buried valley" of the Susquehanna River is situated in the Northern field of the anthracite region of Pennsylvania near Wilkes-Barre. The presence of this buried valley and the uncertainty regarding the extent and physical condition of the water-bearing valley-fill deposits have made great care necessary in mining operations to avoid breaking the strata between the mine workings and the valley-fill deposits to the extent that inundation of the mine workings would follow. The principal factor that threatens to cut short the life of the anthracite industry, to curtail production, and to affect the economic structure of the people and business dependent on anthracite for their livelihood is inundation of anthracite mines (6,7).3

Jan 1, 1950

By W. J. Campbell

This report by the Federal Bureau of Mines Particulate Mineralogy Unit recommends mineralogical definitions and identification-characterization concepts for selected silicate minerals and their asbestiform varieties. Precise definitions acceptable to mineral analysts, regulatory personnel, and medical scientists are essential because of the present lack of conformity in terminology concerned with measuring and controlling asbestiform particulates and their related health effects. Because of the complexity and variability of crystal morphology in different mineral groups, the descriptive terms are generally explained by illustration rather than by numerical values. Applications and limitations of several analytical techniques for particulate identification and characterization are discussed.

Jan 1, 1977

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By E. H. Skinner

An abandoned mine shaft near Omar, in Logan County, W, was permanently sealed through a cooperative agreement between the West Virginia Department of Commerce, Labor, and Environmental Resources, Division of Environmental Protection, and the US. Bureau of Mines (USBM), Abandoned Mine Lands (AML) Program. An engineered shaft seal design was developed and demonstrated that featured lightweight concrete as a key material component at a wet density of about 45 lb/ft3. A reinforced concrete cap designed for 5 psi live load was placed over the shaft seal. Applicable new concrete technologies relating to a 100-yr design life were utilized to assure future integrity of the shaft seal. Waterproofing methods were included in the shaft seal design to provide protection from ambient moisture and corrosive mine waters and to increase the long-term durability of the shaft seal. All construction methods used in the field trial are fully adaptable for the mine-reclamation contractor, The USBM research objectives were to develop a broad generic design that will be widely applicable to other adit-sealing and shaft-sealing problems throughout the mining industry.

Jan 1, 2010

By Kenneth R. Sites

Under this program two tape recording and triggering systems were developed and delivered for use in the Bureau of Mines microseismic program. The systems are designed to improve the effectiveness of the Bureau owned Sangamo 3500 series and SABRE VI instrumentation tape recorders. The system is designed to capture random microseismic data, digitize and temporarily store these data, start the tape recorder; and then transfer the data to magnetic tape for permanent storage. The system is designed to pack data on tape such that the tape may be simply played back through galvo drivers onto an oscillograph such that a continuous series of analog records, with corresponding time of day information, are reproduced without excessive oscillograph paper waste or the need for the operator to search for valid events.

Jan 1, 1980

By A. C. Burr

This progress report covers the period from January 1949 to the end of the fiscal year, June 30, 1950. Three runs were successfully completed, and one run was terminated as the result of failure of a cast reaction tube. Including the abbreviated run, the gasifier was operated for 1,915 hours, during which some 428 tons of natural and steam- dried lignite was partly gasified In producing 20 million cubic feet of gas. Gas-production rates varied from 7.8 to 16.4 thousand cubic feet per hour, the latter being the highest production rate yet reached; hydrogen-carbon monoxide ratios of the product gas varied from 1.85, the lowest ratio yet produced, to 6.5; and heat-transfer rates through the heated wall of the outer tube varied from 2,100 to 4,400 B.t.u. per square foot an hour. The general objective of the project is to establish the technology and economy of the gasification of lignite in an externally heated, metal, annular retort. Specific objectives include determination of the useful life of the metal retort tube, which is a continuing problem, and special objectives that were established for each run as part of the systematic investigation of the basic variables of the gasification process. For runs 10 and 11 the special objective was the influence of the lignite feed rate on gasification; for run 12, a comparison of dried and natural lignite, and the production of gas having a hydrogen-carbon monoxide ratio less than 2; and for run 13, the influence of a gradually increasing steam rate with steam admitted to either the upper or lower reaction zones. In addition, during each run the sulfur distribution and concentration in the product gas and char were investigated. Experimental results obtained using the lignite feed rate as the variable indicated that the gas yield per ton of natural lignite varied inversely with the feed rate. Comparison of the gasification of natural and steam-dried Dakota Star lignite indicated that the dried lignite was a superior gasification material because: 1. The hourly gas production was higher at normal combustion space temperatures under nearly equal experimental conditions. 2. On the moisture- and ash-free basis, a considerably higher feed rate could be maintained at a relatively high percentage of carbon gasified. 3. At nearly equal moisture- and ash-free feed rates, the specific gas yield was higher. The location of steam admission was found to be important because the gas yield per ton of natural lignite was higher when at least a portion of' the process steam was admitted to the upper reaction zone. Heat balances showed the potential heat in the gas and char to be 71.8 to 83.6 percent of the total heat input. The sulfur concentration in the product gas was low, being in the range of 35 to 140 grains per 100 cu. ft., of which 1.5 to 2.3 grains was organic sulfur. Careful measurements and inspection of the 310-alloy rolled plate tube following runs 11, 12, and 13 showed no excessive corrosion; however, some radial deformation had occurred indicating that deformation or creep might be the limiting factor in the life of the tube.

Jan 1, 1953

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, roofing granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of roofing, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural fines available. On the other hand, California manufacturers of asphalt products other than paving utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, slate, and other nonmetallic minerals as filler, mainly for roofing and flooring. Also, about 500,000 tons of roofing granules is produced in California, most of which goes into roofing manufacture in California. In addition, a significantly large and growing tonnage of relatively coarse mineral aggregates are used on low-angle, built-up, asphalt roofs to produce an attractive surface and offer protection against the elements. Nearly all minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of these commodities could be utilized in some use categories.

Jan 1, 1966

By H. R. Batchelder

Much information on oxygen production and the manufacture of synthetic liquid fuels has been published during the past several years. From time to tine the investment and operating cost of oxygen plants of various sizes has been estimated. Surveys have been made so that the various processes by which oxygen is produced commercially might be compared. The gas-making processes in which oxygen is employed, which wore used in Germany during the war, have been described in T.O.M. reels, and this information has been published. Descriptions of pilot-scale or proposed commercial plants for the production of synthesis gas or hydrogen and their conversion to synthetic liquid fuels also have been published. In general, each of these publications has dealt with a particular phase of the over-all problem. The present paper will discuss the relationship between these phases: The factors that affect oxygen manufacture and costs, the methods for the use of oxygen and for the production of synthetic liquid fuels, and, to some extent, the economic factors that must be considered.

Jan 1, 1951

These proceedings consist of papers presented at two Bureau of Mines Technology Transfer Seminars in early 1980 for the purpose of disseminating recent advances in mining technology related to surface coal mining reclamation.

Jan 1, 1980

By R. A. Cattell

With the surrender of the Japanese Imperial Government as a climax to the capitulation of the German High Command , the main objective of the Petroleum and Natural Gas Division pivoted from war assignments to its main normal functions . One of these functions is to give wide public distribution to valuable technical facts which the Division has obtained through research on petroleum , natural gas , helium , and related subjects . During the war years many engineering data and scientific facts could be released only on a restricted basis as reports to war agencies and others immediately concerned . Moreover , many of the wartime reports contained masses of detailed data that were prepared under stress to meet emergency schedules . For peacetime publication and application , these data must be reviewed , correlated , and rearranged so as to present the essentials in proper form . To illustrate , a wartime report of 50 pages might be resolved into one curve in a composite graph for a peacetime publication . Another factor affecting the orientation of the work of the Division is the broader horizon of research revealed by its war activities . Fundamental research and careful engineering analyses are just as important in time of peace as in time of war; in fact , they should be more important to the forward view , because under peace conditions disrupting influences that distract from the orderly acquisition of knowledge are minimized . Therefore , the concerted effort has been not to " salvage " the results of the war activities , but to evaluate them on the basis of their relative importance in the future economy of the country . Where wartime investigations have pointed to peacetime accomplishments , the effort has been to give the corresponding type of work additional emphasis . This adjustment can not be made hurriedly , but many of the necessary preliminary steps on the new course have been taken ..

Jun 1, 1949

By Benjamin W. Haynes

The Bureau of Mines conducted research to provide technical information needed to devise waste management plans for the processing of manganese nodules. Studies included summary descriptions of Pacific manganese nodules, process options and flowsheets, methods for characterizing nodules and their tailings, and results of analyses of laboratory and pilot-plant generated tailings. This information is the result of a cooperative research effort of the Bureau of Mines and the National Oceanic and Atmospheric Administration (NOAA), with NOAA providing funding and the Bureau conducting the research. A summary of the extensive literature review is provided for manganese nodule mineralogy, chemistry, processing techniques, and methods of analyses. Characterizations and analyses of laboratory-generated tailings and slags are given, as well as the results of the leaching studies on these waste materials. Leachability was determined by three standard leachate tests- the Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the U.S. Army Corps of Engineers-EPA seawater elutriant test. While the wastes generated in the laboratory may not be entirely representative of those to be generated in full-scale plants, results of these studies provide a positive indication that commercial recovery of cobalt, copper, manganese, and nickel from manganese nodules would be environmentally acceptable.

Jan 1, 1985

By Oliver Bowles

"Score of the Bureau's Investigations.There has been outlined in a previous report* the results obtained regarding the adaptability of pulverized waste slate as a filler in road asphalt mixtures. As pointed out in that report the percentage of waste at slate quarries is very high, and the Bureau of Mines has undertaken the problem of discovering new and enlarged outlets for the waste material.Many products such as paper, rubber, road asphalt, floor coverings, paints, etc., require as one of their important constituents a considerable percentage of finely pulverized inert mineral matter to give ""body"", to obtain the desired consistency, or to supply the necessary wearing or other qualities demanded. Such materials are known as ""fillers"". The possibility that slate flour might be used as a filler with advantage in several products other than road asphalt led the Bureau to undertake further investigation.The Importance of Discovering Advantageous UsesIt has been found that in some products slate may be substituted for materials now in use without any marked effect on the quality of the products. A wider use of slate in such products could result only from a definite price advantage as compared with other fillers. Mile it is probable that waste slate may be placed on the market at prices which will encourage its wider use, it is evident that a waste slate utilization industry can never attain sufficient magnitude to definitely assist the slate producers unless it is demonstrated that some definite advantage in quality may be gained when slate is substituted for fillers now in use. The main purpose kept in view throughout the inquiry has been, therefore, to find advantageous uses for waste slate in order that both producer and consumer may be benefited."

Sep 1, 1921

By Gregory Molinda

Historically, coal miners have known that roof shales can deteriorate in contact with humid mine air, causing massive roof falls and injuries from falling rock. It is critical to recognize rocks prone to weathering and to adequately support these rocks in order to ensure the long-term stability of the openings. In a recent study, NIOSH has used a wet/dry cycling test to determine the moisture sensitivity of over 800 specimens of roof rock from 25 U.S. coal mines. Fireclays and some gray shales are the most moisture-sensitive. Rocks with disturbed bedding, in contrast to flat-bedded rocks, are also more sensitive to water. Black shales are relatively un-reactive to moisture and serve to protect more reactive gray shales above. Mines that have roof rocks with moisture-sensitivity indexes above 40% can experience slaking roof conditions, and many require high coverage surface controls. Three case studies are presented in which the moisture-sensitivity index is correlated to roof conditions underground, and can be used to indicate long term deterioration. Engineering measures are described to control moisture-sensitive roof. In one case, roof screen not only reduces injuries from rock fall but also is shown to reduce roof falls. Keywords: coal mining, roof control, slaking, roof support, rock falls

Jan 1, 2008

By R. L. Grant

During the last decade or more , experimental research on commercial detonators used for initiating the detonation of dynamite and other high explosives has led to important improvements . Developments , especially in the United States , have been directed toward improvement in the construction of detonators to make them safer to manufacture and use . More suitable and safer initiating charges also have been found . Although for many years mercury fulminate was unrivaled as the initiating charge for dynamite , during the last decade it has been replaced to a large extent by less sensitive , more efficient, and cheaper combinations of ignition , priming , and base charges . Commercial detonators were once of relatively simple construction and almost universally identical . Today they are technically complex, with special nodifications for particular uses ; they have developed along different lines n various countries and even among the several manufacturers within any one country .

Apr 1, 1943

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2 ) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs' estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By V. F. Parry

The major industrial uses of char or semicoke produced by low-temperature carbonization of coal4/ are as fuel for generating electric power, for blending with metallurgical coking coal as a substitute for low-volatile coals, and for gasification to produce synthesis gas for chemical purposes. This paper discusses various methods for carbonizing coal, emphasizing processing of the noncoking coals to produce char for thermal power-plant fuel and for blending with metallurgical coking coals and tar for chemical use. Low-temperature carbonization is a relatively simple processing step involving heating coal to about 900° to 1,200° F. to decompose the coal into 4 main products: (1) Semicoke or char; (2) complex, partly oxygenated liquid hydrocarbons or tar; (3) fixed gases; and (4) water. If the coal is heated rapidly under conditions that prevent decomposition of the primary products, 68 to 87 percent of the net heat in the raw coal is left in the char and 10 to 23 percent of the potential heat appears in the primary tar. Fixed gases represent approximately 7 percent of the heat and approximately 2 percent is lost or dissipated in the reactions of decomposition. Considering the different ranks of coal in the United States, the yield of tar will vary from about 9 to 44 gallons per ton, therefore it is important that each coal be carefully considered if it is to be carbonized for industrial use.

Jan 1, 1955