Search Documents

By Robert J. Evans

The Bureau of Mines is sponsoring a variety of long-term, high-risk research to advance state-of-the-art technology in U.S. underground coal mining. This report reviews the status of many Bureau projects that support fundamental underground coal mining operations; the project areas include cutting coal from the solid (extraction), hauling coal from the face (transport), and activities that sustain daily operations (logistics). Innovative equipment and technology have been developed, with these major objectives: to significantly improve coal mine productivity, to further advance coal recovery and personal safety within the mining industry, and to reduce the time needed to develop longwall panels. The majority of the prototype equipment covered in this report either has undergone or will undergo comprehensive evaluation at Bureau surface test facilities so that performance and reliability can be improved before the equipment is tested and evaluated in a working section underground.

Jan 1, 1988

By R. V. Higgins

The, large volumes of low A. P. I. gravity oil that will remain in many shallow fields of California when such oils no longer can be recovered profitably by pumping are important potential sources of oil when ways and means are found to remove them from the reservoir sands. Estimated ultimate oil recoveries in many of the "low-gravity fields" of the San Joaquin Valley in California indicate that less than 25 percent (on the average) of the original oil will be recovered. These oils have viscosities of 1,000 or more centipoises at reservoir temperatures and, because of their high viscosity and low intensity of the reservoir pressure, the quantities that will be retained in the sands ultimately are so large and their recovery is such a challenge to petroleum engineers that the Bureau of Mines has made the study of their possible recovery one of its major projects. The fact that a slight increase of temperature materially reduces the viscosity of low A. P. I. gravity oils has 'prompted the use of various means for increasing the temperature of the oil in the reservoir sands and hence the rate of flow and Completeness of recovery of the oil. Hot oil, hot water, heated air, and natural gas, steam, super-heated steam, and the products of combustion have been circulated in wells to raise the temperature of the oil it the sands; electric heaters have been installed in wells, and butane and air have been intermittently exploded and the flames propagated through the tubing to the "pay" zones. None of the methods, however, have been entirely satisfactory for the recovery of large quantities of oil.

Jan 1, 1949

By W. W. Adams

The United States Bureau of Mines, in cooperation with the National Send and Gravel Association conducted a safety contest in 1929 Among producers of sand and gravel. Only 26 plants were enrolled, as the contest was late getting under way. It is hoped that a ranch larger number of plants will be represented in the safety competition of 1930. Two trophies, both of which were provided by Rock Products magazine, were awarded at the end of the contest; one trophy was given for the best safety record among plants working 100,000 or mare man-hours during the year and the other for the beat record among plants working less than 100,000 man-hours. The trophies were presented to representatives of the winning, companies on January 29, 1930, at the annual convention of the National Sand and Gravel Association at Memphis, Tenn.

Jan 1, 1930

By Neal M. Muir, Robert S. Sanford, Bruce I. Thomas

"INTRODUCTION The presence of the zinc-lead-copper deposits an the north slope of Mount Eielson, Mount McKinley National Park, Alaska, has been known for many years. The deposits were examined by J. C. Reed, a geologist of the United States Geological Survey during the summer of 1931. In the summer of 1943 the authors and Clyde Wahrhaftig, a geologist of the Geological Survey, examined the deposits.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the and that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.Particular acknowledgment is due to Heine Kenworthy, who conducted the beneficiation tests under the supervision of C. Travis Anderson; to Clyde Wahrahaftig of the Geological Survey, who completed the Geologic and topographic maps, to Grant Pearson of the National Park Service; and to O. M. Grant and Mrs. Frank McGarvoy for their assistance during the examination."

Nov 1, 1947

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By Natesa I. Jayaraman

A field study was conducted by the Bureau of Mines to determine the feasibility and effectiveness of a secondary ventilation system retrofitted onto an Eickhoff EDW 340L double-drum shearer as a technique for controlling respirable dust generated during a longwall mining operation. An airflow duct was formed by enclosing the bottom of the undercarriage with steel plate and cutting air channels through the ends of the undercarriage frame. Air intakes were provided behind each cutting drum and at several locations along the undercarriage. Grills were installed at the intakes to prevent the broken coal from entering the ducting. A dust collector consisting of 5,000-ft3/min fan, water sprays, and a minicyclone panel was installed on the shearer at the tailgate end. Field results indicated that the secondary ventilation system reduced respirable dust more than 60% along the face. Reduction was less near the intake airway and when secondary dust sources occurred.

Jan 1, 1977

By L. D. Schmidt, H. G. Graham

Several processes for the production of ultra-clean coal for electrode carbon were developed in Germany prior to and during World War II . These processes have been investigated since the end of the war by the British and U. S. Government missions . As the reports of the investigations are not readily available to the public , it is the purpose of this paper to present the information which has been obtained regarding the methods by which ultraclean coal was produced . Almost all the ultra-clean coal was used in the manufacture of electrodes for the production of aluminum and magnesium . Standard raw materials for making these electrodes are pitch coke and petroleum coke , which are nearly ashless . The inclusion of ash in the electrode carbon results in lowered efficiency and impure metal from the reduction process . Petroleum coke and pitch coke were in very short supply in Germany during the war , so that it was necessary to augment the supply with carbon produced from coal . In the emergency , methods were developed to clean coal which had never before been economically feasible . However , a demand for nearly ash-free coal might develop in the United States if a shortage of petroleum coke were to occur at the same time as a strong demand for light metals . Other uses of ultraclean coal are in direct hydrogenation of coal , in production of activated carbon, and for special fuels . Specifications for electrode carbon are rather severe owing to the necessity for producing pure metal . Maximum amounts of impurities allowable in American practice are as follows : Total ash , 1.0 percent ( in finished coke , 0.7 percent ) Silica , 0.08 percent Ca or Na, or their sum , 0.12 percent Sulfur , 2.0 percent Ba , Ni , Cr , Mn , Co , and V are objectionable in very small amounts . The most important process for ultra cleaning of coal in Germany was froth flotation . Froth flotation had been used widely there to process washery -water sludges and to recover coking coal from high - ash fines . Its use was indicated , therefore , when the demand for ultra low-ash coal arose . In two plants the coal cleaned by froth flotation was treated with acid or caustic to lower further the ash content . Another process used on an industrial scale was that of dissolving the coal substance in the middle oil from direct hydrogenation of coal under controlled pressure and temperature . The resulting paste was heated, filtered , and the oil distilled off . The residue was a low-ash organic material that could be carbonized for electrode carbon or could be hydrogenated directly . Several other processes had been developed to the laboratory or pilot - plant stage but had never been used on a commercial scale . These processes included cleaning by centrifugal action , cleaning by electrostatic action , and cleaning by forming a paste with oil in water . The coal-preparation plants at the Carl Alexander mine , Augusta Viktoria mine , and Kőenigin Elisabeth mine are described in Bureau of Mines Information Circular 7389 : " Coal Preparation Practice in Western Germany" , by Thomas . Fraser and M. G. Driessen . Most of the special equipment used at these plants is described in the above publication .

Oct 1, 1948

By J. F. Barkley

Field tests were made on the rate of corrosion of 30 materials used in air preheaters under regular operating conditions, and the buildup of deposits was observed. Twenty-three materials were tested with coal as the fuel on an underfeed stoker and seven with oil, including a short period with pulverized coal as fuel, The plant equipment is described, and pertinent plant operating data are tabulated. Figures 17 and 19 (pp. 24 and 27) give the results of corrosion tests on the uncoated metal test specimens. The information obtained from these tests follows the general pattern described in Bureau of Mines Report of Investigations 4996, Corrosion and Deposits in Regenerative Air Preheaters. The deposits were similar, and the corrosion rates of Cor-Ten and Mayari-R steel (previously found to be essentially the same at the Harding Street Station using coal) continued to show little difference at the Marion Generating Station using principally oil. The one high-alloy steel tested, type 321, showed a much higher corrosion rate than the low-alloy steel, Cor-Ten.

Jan 1, 1959

By Fred N. Kissell, Andrew B. Cecala

In This Chapter [Where methane is emitted at longwall faces Where methane accumulates at longwall faces Using the modified shearer-clearer to eliminate ventilation eddy zones Using a walkway curtain to reduce methane buildup during the headgate cutout Control of frictional ignitions and The best location for the methane monitor] The methane released along a longwall face represents only 10%–20% of the total methane emitted from the entire longwall panel. Nevertheless, in very gassy coal seams, this methane released at the face can pose a problem because the shearer is a ready ignition source. Preventing methane ignitions at longwall faces requires four actions. The first is to provide better ventilation around the shearer to eliminate the ventilation eddy zones at the drums where methane builds up. These eddy zones are eliminated by mounting additional water sprays on the shearer to direct air into them. The second action to prevent methane ignitions is to install a water spray behind each cutter bit and regularly replace worn bits. Water sprays behind each cutter bit act to quench the hot metal streak that follows a worn bit when it strikes rock. The third is to ensure that no ventilation eddy zones are inadvertently created by poor placement of water sprays. The fourth is to ensure that the methane monitor on the shearer is in the best location to detect methane accumulations. ADDRESSING METHANE ACCUMULATIONS AT LONGWALL FACES3 Cecala et al. [1985a, 1989] and Denk and Wirth [1991] studied methane emission and ventilation patterns at longwall faces to find where methane accumulations are most likely. Although not always the case, the major source of methane at longwall faces is usually the breakage of coal by the shearer. Stress-related fracturing of the coal seam at the face, called bumps or bounces, can cause the release of additional gas (Figure 4–1).

Jan 6, 2006

By John A. Burgess

The Carson Hill mine of the Carson Hill Gold Mining Corporation is at Melones, Calaveras County, Calif. It is one of the numerous mines on the Mother Lode of California. The property extends for 8,400 feet along the outcrop of that important vein system. The elevation at the haulage level is about 1,000 feet above sea level. ACKNOWLEDGMENTS Acknowledgment of assistance in the preparation of this paper is made to Frank Wagner, underground superintendent; Max Petersen, engineer; and Homer Mann, assistant engineer. The geology of the Mother Lode has been described by Adolph Knopf in Professional Paper 157 of the United States Geological Survey; references to general geology have been abstracted largely from Knopf.

Jan 1, 1937

By Peter P. Kopas

Study, analysis, fabrication and testing for canopies on Roof Bolters and Shuttle Cars in coal seams under 48?.

Jan 1, 1980

By Ovsei Volberg

Motion capture involves recording the position and global orientation of joint sensors of a real object, in most cases a real person performing some human activities. This information is usually recorded at uniformly spaced instances of time, or as it is often called frame-by-frame. Then the recorded motion data sets are processed and mapped into a skeleton hierarchy of a virtual, computer simulated human figure to control the motion of the virtual human in the computer simulation. In the first part of the paper we review several new techniques developed to facilitate the manipulation, noise reduction, storage and reuse of captured data, which have a potential to reduce the overall cost of motion simulation and improve its realism. In the second part of the paper we consider the real life problem of reducing a worker?s risk from being hit by underground mining machinery in a confined space. We formulate a set of requirements to motion editing for this particular task and analyze the limitation of existing techniques

Jan 1, 2000

By James S. Wroth

The Act of Congress approved June 25, 1926 (Public Act 424, 69th Congress), authorized joint investigations by the U. S. Geological Survey and the U. S. Bureau of Mines to determine "the location, extent, and mode of occurrence of potash deposits in the United States." The particular deposits selected for exploration were the extensive rock-salt formations underlying large areas in western Texas and southeastern New Mexico, from which potash salts had been identified in the cuttings and sludges from oil wells drilled with cable tools. The evidence of these sludge samples was qualitative only and beyond definitely proving the presence of potash salts in the salt beds, gave little clue to the possible size, richness, or extent of the potash occurrences.

Jan 1, 1929

By S. M. Marshall

The investigations recorded in this bulletin were conducted by the Pacific Coke & Coal Co. in cooperation with the United States Bureau of Mines and the University of Washington. They cover one phase of a comprehensive investigation to determine whether coals from an extensive, undeveloped area of Pierce County, Wash., can be used in the manufacture of coke for the iron blast furnace. The completed investigation had three parts: (1) A geological survey of the coal property, (2) washing and crushing tests of the coals, and (3) coking and by-product tests. The geological survey, which was not conducted in cooperation with the Bureau of Mines and the University of Washington, included systematic tracing of the coal beds by test holes throughout the property, except some portions covered by an impenetrable layer of glacial drift. By this means all of the beds were correlated, their thickness and general character were determined, and tonnage estimates were made. Only such parts of the survey results as are necessary to a full explanation of the investigations described herein are included in this bulletin.

Jan 1, 1931

By William C. Morel, Sidney Katell

This report covers the period January 1964 through December 1964; it is a continuation of the series that began with the publica- tion of Information Circular 7516 in October 1949. Also, it is the sixth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engin- eers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal--Today and Tomorrow. 9. Cost Engineering. 10. Hydrocarbon Processing and Petroleum Refiner. 11. Industrial and Engineering Chemistry. 12. Nucleonics. 13. 011 and Gas Journal. 14. Petroleum Management. 15. World Oil.

Jan 1, 1965

By E. D. Palmes

This report was prepared by New York University Medical Center, Institute of Environmental Medicine, 550 First Avenue, New York, New York under USBM Grant Number G0133066, Personal Samplers for CO, NO and NO2 in Air. The grant was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of the Pittsburgh Mining and Safety Research Center with Dr. George H. Schnakenberg acting as the Technical Project Officer. Mr. L. Young was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this grant during the period 3/1/73 to 11/30/76. This report was submitted by the authors in March, 1977.

Jan 1, 1977

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat-room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all accidents.

Jan 1, 1957

In attempting the predict coal cleat orientation in the subsurface for effective methane degasification of the coal beds in the Warrior coal field of Alabama, approximately 150 rock joint orientations and 45 coal cleat orientations were measured in each of 37 7 ½ minute quadrangles in Tuscaloosa, Walker, Jefferson, Fayette, Winston, Blount, and Bibb Counties. Data from these surface locations, and coal cleat data from eight underground mines was corrected for magnetic declination and titled beds rotated to the horizontal where necessary and plotted on rose diagrams for comparative analysis. Data collected on each joint and cleat consisted of attitude, quality, type, spacing, persistence, lithology, bedding thickness, surface texture, and filling. File data and published and unpublished reports from the State Survey and the State Mine Inspector's Office were re-viewed. Twenty-seven mining companies, most of which supplied information pertinant to the project were also contacted. The information obtained consisted of crop line information structure, and underground mine outlines, all of which were put on 7 ½ -minute topographic quadrangles. LANDSAT-1 imagery and Skylab photography were compared to dominant joint and cleat trends in the study area. Detailed results can be found in an open-file report entitled "Fracture Analyses in a Selected Area of the Warrior Coal Field, Alabama." A master's thesis entitled "The Relationship Between Surface Joints and Subsurface Structure in a Selected Area of the Warrior Coal Field" is being prepared to illustrate the relation-ship of the fracture system to the structure in the Warrior coal field. A proposal has been submitted for research on a project entitled "Rock Fracture Systems and Their Affects on the Extraction of Fossil Fuels in the Warrior Basin, Alabama"

Jan 1, 1976

By William H. Pomroy

This report describes Bureau of Mines research that led to the design, prototype fabrication, and successful proof-of-concept testing of an improved stench fire-warning system for underground noncoal mines. Stench systems are the most widely used means of warning driers in underground noncoal mines of fires or other emergencies. A stench system alerts miners that an emergency condition exists by injecting an odorant into the mine air. Although stench warning systems have been used successfully for over 60 yr, present systems suffer several serious shortcomings, including odorant toxicity, unreliability of warnings, widely varying stench concentrations, and others. In 1980, the Bureau began a research program to upgrade the stench warning system. The resultant system overcomes the deficiencies of existing systems by substituting tetrahydrothiophene for the commonly used ethyl mercaptan stench odorant, and through the use of a specially designed stench injector. The improved injector reliably meters stench fluid into either ventilation-air or compressed-air streams at a precisely controlled rate. Prototype hardware has been fabricated and proof-of-concept tested under bath laboratory and in-mine conditions.

Jan 1, 1985