Search Documents

By Mirza A. Beg

The Piedmont physiographic province of east-central Alabama lies in a humid subtropical climatic zone. Such an area with mature land forms underlain by rocks rich in feldspars provides conditions condusive to development of gibbsite, a major source of alumina; a raw material for which the United States relies on foreign suppliers for 85 percent of its needs. Gibbsite occurs in the northern and inner sections of the Piedmont Province of Alabama in Coosa, Clay, Randolph, Chambers, Elmore, Tallapoosa and Lee Counties in soils and saprolite derived from amphibolites, granites, feldspathic hornblende gneiss and other gneissic rocks. The major occurrences of gibbsite are in areas underlain by hornblende gneiss in Chambers and Randolph Counties. This region provides the proper physiographic and mineralogical setting for large areas containing up to 25 percent of saprolitic gibbsite. These areas provide potential sources of alumina that could be used to meet the United States future needs. Narrow zones and pockets rich in gibbsite also occur in soil and saprolite derived from areally restricted feldspar rich zones of narrow linear amphibolites in the inner Piedmont and feldspathic zones in various granites distributed throughout the Piedmont.

Jan 1, 1982

By L. D. Tracy

Many bituminous coal-mining companies have inaugurated extensive safety programs, but the failure to have approved or permissible equipment or safe practice in only one part of a mine has resulted in disaster. The necessity of using only equipment bearing the U. S. Bureau of Mines approval plate is emphasized by the fact that many accidents are the direct result of carelessness on the part of trusted employees using non-permissible equipment. A concrete example is found in the case of an explosion on October 26, 1926, in a mine in the Pittsburgh district, Pennsylvania. Story of the Explosion At about 10 o'clock on the night of the explosion an examination was made in No. 2 butt left and parallel off No. 14 north, and was found to be clear of dangerous accumulations of gas. (See figure). Several hours later a crew of two men brought a self-propelling rock-dusting machine within 50 feet of the face of No. 2 butt parallel before they examined for gas. The machine operator found an accumulation of explosive gas about 13 inches from the roof. He began to wave his arms thoroughly mixing the gas and air. Undoubtedly a highly explosive mixture was created, and as the men attempted to run the machine back to fresh air as explosion occurred.

Jan 1, 1927

By B. K. Shibler, W. G. Sandell, G. M. Potter, H. D. Snedden

"INTRODUCTION During the course of the investigation of the occurrence of manganese deposits in the western United States, examining 'engineers of the Bureau of Mines collected samples from seven manganese properties in Grand and beery Counties, Utah. These were supplemented by five samples submitted by property owners. Since all of the ores were too low-grade for use in producing ferromanganese for steel manufacture, some means of beneficiation was required to produce marketable concentrates, and metallurgical studies were made on each of the samples.Most of the ores Investigated are similar in one respect: At least part of the 'manganese oxide areas contains minute inclusions of gangue. This occurrence materially enhances the complexity of the ore, partly by .increasing the complexity of mineral association, but largely through making manganese-quartz liberation more difficult. In such ores, there is a marked tendency for the manganese minerals to be retained as shells or coatings on the surfaces of quartz particles when crushed. Particles of this type represent considerable loss of manganese in tailing, if gravity-concentration methods are employed, or tend to' float, thus carrying an appreciable quantity of gangue into the concentrate, if treated by flotation.Plus 48-percent manganese sinters were made from some of the ores tested, but, in general, intimate association of manganese minerals with silica limited the degree of beneficiation attainable."

Dec 1, 1947

By Daniel G. DiCanio

This report describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents in underground coal mines. The study undertook to identify and quantify the elements of accident costs, including field visits to coal mines, insurance carriers, and public agencies. The mathematical models developed for each tangible element of accident cost are presented in Volume I of the report. A listing of the computer programs which comprise the model and instructions for using the programs are presented in Volume II. Statistical distributions of mining family characteristics, data on 95 miners killed in underground accidents, and other basic data used to develop the model are presented in Volume III. Application of the model to a data base of 9,286 accidents which occured in underground bituminous coal mines during 1974 yielded a total of $56,900,000 in tangible costs to industry, mining families, and public agencies. Loss of income to the families of miners injured or killed in these accidents accounted for 47 percent of the total.

Jan 1, 1976

By Dong G. Chae

A model for the leaching of oxide ores is developed and II correlated with laboratory tests for percolation leaching of copper oxide are. Using the model, recovery of metal values and lixiviant concentration of the effluent solution at any time may be evaluated. For the copper oxide ore a simplified version of the model is examined for the leaching mechanism consisting of: 1) a surface flush reaction with the highest rate of lixiviant consumption; 2) penetration of lixiviant to react with copper minerals and gangue constituents; and, 3) slow lixiviant consumption, mostly by residual gangue materials. The simplified model is able to explain reasonably the leaching behavior of copper oxide ore by introducing a concept of effective initial size to correct for packing in a bed of fine particles.

Jan 1, 1979

By Michel C. Frippel

This section of the Minerals Yearbook reviews the minerals industries of 27 countries: the 12 nations of the European Community (Belgium, Dermark/Greenland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, and the United Kingdom); 6 of the 7 nations of the European Free Trade Association (Austria, Finland, Iceland, Norway, Switzerland, and Sweden); Malta; the 8 Eastern European economies in transition (Albania, Bulgaria, Czechoslovakia, Hungary, Poland, Romania, and Yugoslavia); and the U.S.S.R. Western Europe Western Europe [loosely defined to include the 12 nations of the European Community (EC) and the 7 nations of the European Free Trade Association (EFTA)] is the single largest trading area and consumer of raw materials in the world. If Western Europe was at one time an important mining sector, it has now increasingly relegated the role of supplying minerals for its minerals processing industry to the more minerally endowed countries in North and South America, Africa, and Australia. In this regard, Western Europe is the most important determinant of raw materials consumption (and thus, indirectly, raw materials production). Western Europe has significant reserves of industrial minerals but has limited availability of metalliferous raw materials. It, therefore, imports significant quantities of the latter and ranks along with the United States and the U.S.S.R. in the production of refined metals. Nonetheless, there is an inherent tendency to underestimate the importance of Western Europe in the world of minerals, both as a minerals processor and raw materials buyer. The reason for this is that Western Europe is generally thought of on the basis of individual nations rather than as a whole. Viewed in this limited context, the United States, the U.S.S.R., and Japan appear to dominate the world economy. Viewed as one regional area, however, Western Europe includes the fourth (FRG), fifth (France), sixth (United Kingdom) and seventh (Italy) largest economies of the world, all bordering on one another. With the remaining 15 EC and EFTA countries, Western Europe has a land area approximately 40 % of that of the United States, exceeds the U.S. population by 50 % and has a gross domestic product about the same as that of the United States.

Jan 1, 1993

Objective: On-the-job training (OJT) is a common means of training workers. By definition, it seems relatively simple. However, to be effective, training must go beyond the simple process of following an experienced worker around the workplace— sometimes called the "follow Joe" method. NIOSH researchers spoke with human resources personnel, safety and health specialists, supervisors, experienced miners, and new miners and found that OJT was of high interest, but was rarely part of a formal or standardized program. Various training methods have evolved to ensure that a trainee will absorb the information presented rather than simply emulate what the instructor is teaching. These methods have been brought together into a published guide for developing an effective formalized OJT program. The guide (Information Circular (IC) 9479) is called "Coaching Skills for On-the-Job Trainers." It contains materials and suggestions for your company or mine to conduct a 1-day workshop for teaching OJT trainers how to be better coaches to less experienced workers. The guide was created by the NIOSH Pittsburgh Research Laboratory and a safety professional from a private mining company.

Feb 1, 2006

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world's largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By R. J. Leary

Oxidation testing of copper-clad steel strip was performed in a muffle furnace to determine whether copper in contact with steel scrap could be removed by oxidation in an airstream at high temperatures. Substantially all of the copper was oxidized before any significant iron oxidation occurred. The rate of copper oxidation was not affected by contact with iron. Copper oxide scale separated spontaneously from the underlying metal during cooling. Results indicate the possibility of removing light-gage copper coatings and components from ferrous scrap by oxidation in an incineration process.

Jan 1, 1965

By Chas. F. Jackson

This paper is published as a progress report for the first half of 1929 on the study of wining methods and costs in the Eastern and Central States. Data obtained from 25 mines using open-stope methods are correlated and summarized. Some of these mines have been described in considerable detail in reports already published as Information Circulars. In addition to the published reports on individual mines, considerable data have been obtained from other mines which were visited and studied during the course of the investigation. Many of these mines will later be described in detail in separate papers, and when the field has been covered in this manner it is planned to issue a bulletin on open-stops methods of mining which will amplify the subject matter of the present paper. Definition of ?Open-Stops?. - The term "open-stopes" as employed by the Bureau of Mines is applied to all naturally supported stopes; that is, stopes in which the excavated ore is not replaced by support of an artificial nature other than preps or stulls and in which the ore or (and) capping are not caved during the active life of the stopes.

Jan 1, 1931

By P. A. Lawless

The objective of the research performed A for the Bureau of Mines on this contract was to develop a portable instrument for the detection of carbon monoxide (CO) in a mine environment. The desired characteristics were sensitivity and specificity for CO with a stable calibration. The sensor of the instrument was to be of metal oxide composition, requiring low power for compatibility with the types of batteries presently used in personal equipment in mines. The solid state design was also desired for ruggedness and small size. A key design feature of the instrument was to be provided by adherence to the intrinsic safety design requirements for electrical equipments operated in potentially exposive mine atmosphere. The Research Triangle Institute has prior experience in developing a solid state oxygen sensor using a thin film of zinc-oxide (Ref. 1) and experience in fabricating thin film devices. Solid state sensors utilized by other workers (Refs. 2, 3, 4, 5, 6) have included metal and semiconductor films and crystals of materials like carbon and aluminum oxide for the measurement of water vapor in the air and have relied upon measuring resistance and capacitance changes in the sensor in response to adsorbed vapors or gases. Since the effect of carbon monoxide in changing the resistance of various materials such as molybdenum, platinum, and zinc oxide had been reported (Refs. 7, 8, 9, 10), the requirements appeared to be realisable, although it was recognized even at the inception of the work that specificity to carbon monoxide might require the incorporation of more than one sensor.

Jan 1, 1976

By M. Karmis

Surface subsidence is an inevitable consequence of many underground mining operations and has been recognized as such since the fifteenth century. Damage resulting from this phenomenon ranges from simple land settlement to severe structural damage to buildings and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). In fact, it is estimated that over 2 million acres of land across the United States have been affected by mining subsidence, of which 140,000 acres are in urban areas (Singh, 1978; Johnson and Miller, 1979). Further, it is estimated that during the next twenty years an additional 1.5 to 2.4 million acres of land will also be affected by mining. Subsidence prevention is not feasible, at least under the existing technologic and economic constraints of underground coal mining. Foreign experience has demonstrated, however, that subsidence can be successfully controlled if an accurate method of predicting ground movements is available. Such techniques have been developed in many coalfields, where it is currently accepted that subsidence can be predicted within ± 20 percent of the actual values. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented.

Jan 1, 1983

By Laurence G. Trudell

Geology and oil-yield data are presented for a 58-square-mile area encompassing the U.S. Department of the Interior oil-shale leasing program tracts in the western Washakie Basin, Sweetwater County, Wyo. Lithology and oil yields of samples from three Bureau of Mines coreholes are evaluated and correlated with Kinney Rim surface sections measured and sampled by the U.S. Geological Survey. Minable sections of oil shale averaging up to 25 gallons of oil per ton crop out on Kinney Rim in the Laney Member of the Green River Formation. Thick oil-shale sections in the Laney Member that average 15 gallons per ton represent 155 million barrels of oil in place per square mile. In the lower part of the Green River Formation the Tipton Shale Member contains a 20-to 40-foot section averaging 15 gallons per ton. Beds of high-volatile C bituminous coal up to 6 feet thick are present in intertongued parts of the lower Green River Formation and upper Wasatch Formation.

Jan 1, 1973

By Oliver C. Ralston, Foster Fraas

The electrostatic separation of solids utilizes the forces exerted when electrically charged particles of the solids are present in an electric field . The charges may be acquired by various means (5) , and when the acquisition or loss of charge depends on the property of the particle , separation can be obtained between particles having different properties . A property commonly utilized in present - day separators in conductance . Charging also may be accomplished by bringing the particles into intimate contact with various surfaces . This is sometimes described as a " frictional electrical effect. The charge , or specifically the polarity of the charge , in this latter case evidently depends on the property known as the contact potential , as has been explained in the discussion of a paper (7) and in several other papers (10) . Separation by this method is accomplished in two steps - a charging step , in which the particles are brought into intimate contact with an electrification surface , and a separation step , in which the charged particles are separated in an intense electric field . Descriptions of such methods may be found in the literature (2) , (7) , ( 8) . Even as early as 1909 , Blake and Morscher (2) described the charging of particles by intimate contact followed by separation in an electric field . They also state that the polarity of the electrical charge acquired by the particles depends on their composition . O'Brien ( 8) presented several designs of apparatus . He obtained electrification by means of a wiping action , either on inclined plates or in rotating cups , in which a centrifugal force was imparted to the particles .

Nov 1, 1942

By H. M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since in most fields gas under pressure is the main source of the energy causing the oil to move through the sands into the wells and thence to the surface, coincident production of natural gas will continue as long as present-day producing methods are used. Generally the use of this gas is restricted, since markets are not readily available. Consequently, a large portion of the gas produced is often wasted by being blown into the air. The magnitude of gas waste is well brought out in the following statement by Miller: Only a few outstanding examples need be cited to show the enormous production of gas that accompanies the discovery of new sources. In April, 1927, the Ventura field produced approximately 210,000,000 cubic feet of gas a day; and during the summer of 1927 Alamitos Heights reached a peak gas production of 102,000,000 cubic feet a day; on December 1, 1928, as a result of the summer's deeper drilling in the Long Beach field, surplus gas production amounted to 125,000,000 cubic feet a day. It is estimated that in January, 1929, the Santa Fe Springs field will have a daily gas production of 387,000,000 cubic feet from the recently discovered Buckbee oil zone. Of this amount 274,000,000 cubic feet a day will be the surplus above the amount required for field and plant fuel, taken out by utility corporations, and that used in repressuring the Meyer sand which lies above the Buckbee zone. Another example of the waste of large volumes of gas is in the Turner Valley field of Canada, 6 where 250,000,000 cubic feet of gas is being burned daily in flambeaus, as there is no present outlet except at prohibitive cost.

Jan 1, 1931

By H. W. St. Clair

This study was undertaken to provide a more adequate knowledge of the chemistry of the sulfide volatilization process for recovery of tin from low-grade Bolivian ores. The investigation was partly supported by the Department of State under its program for scientific cooperation with South American republics. The results of this investigation demonstrate the conditions under which cassiterite (Sn02) may be converted to stannous sulfide by reaction with pyrite or sulfur vapor, Quantitative data are given on the rate of sulfidization and on the vapor pressure of stannous sulfide.

Jan 1, 1954

On July 1, the Bonneville Power Administration announced a 25% power cutback because of lower than normal stream flow. In September, the Aluminum Company of America (Alcoa) announced plans to shut down one 23,000-ton-per-year potline at its Vancouver, Wash., primary aluminum smelter. Alcoa also announced that the last of four potlines at its Point Comfort, Tex., primary aluminum smelter would be restarted in October. A new 3-year contract was signed and workers at three Alcan Aluminum Ltd. primary aluminum smelters in Canada returned to work. It was estimated that it would take about 3 months before the smelters were operating at full capacity.

Jan 1, 1979

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, are investigating technology and methods to monitor the blind areas around large haulage equipment used in surface mines. On average, six fatalities a year can be attributed to equipment colliding with other vehicles or pedestrian workers, or backing over the edge of a dump point. Several off-the-shelf technologies exist for monitoring areas that an equipment operator cannot see from the cab, including radar, video cameras, and radio signal detection systems. NIOSH researchers have tested many of these systems on large dump trucks both at their test facility and at surface mines. This article discusses the technologies available for this application and their effectiveness in detecting objects near an off-highway dump truck. Also, guidance is presented for mine safety personnel who are planning to evaluate collision warning systems or cameras on their haulage equipment. Available Technology Over the past few years, the number and types of systems available for monitoring the blind areas around heavy equipment have increased. Systems marketed for the automotive and recreational vehicle industries have been around for a while. Small video cameras can be found

By F. R. Lee

THE Bureau of Mines was established in July 1910 to conduct research and to establish standards for mining equipment and practices which would conserve human life, natural resources, and property in the mineral industries. Several lists of equipment approved by the Bureau as permissible for use in gassy coal mines have been issued since then. The lists covering all approved equipment except breathing apparatus and explosives have born consolidated into two publications: Bulletin 343. Permissible Equipment Approved to January 1, 1953, and Information Circular 8220, Permissible Mina Equipment Approved By The Bureau of Mines During 1953-62. The, purpose of this publication is to supplement Bulletin 343 and Information Circular 8220 with a listing of permissible equipment approved during 1963 and 1964. The schedule, (standards) under which equipment listed herein have been approved are, as follows (cities and dates of approval and revision are, given in footnotes) : Schedule 2F,3 schedule 6D,4 schedule 7C,5 schedule 8C,6 schedule 9B,7 schedule 10C,8 schedule 12D,9 schedule 22,10 schedule 24,11 schedule 25B,12 schedule 25B,13 schedule 29A,14 schedule 30,15 and schedule 31.16

Jan 1, 1966