Search Documents

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitled ?Evaluation of Proximity Warning Devices? dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electrostatic fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factor of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By Robert L. de Beauchamp

The Bureau of Mines designed a chlorination apparatus to prepare CrCl2 free of CrCl3 by the direct reaction of chlorine and chromium. Equipment and procedures were developed for routine preparation of 25-pound batch quantities of anhydrous CrCl2. Calcium, iron, nickel, and silicon impurities were in the 0.01 to 0.05 percent range, and all other impurities were below 0.01 percent.

Jan 1, 1968

By R. B. Schluter

Magnetite pellets were simultaneously reduced and indurated on a laboratory scale in order to determine the effects of temperature, induration time, degree of metallization, and sulfur content upon the physical and chemical properties of prereduced pellets. The reductants were commercially-pure tank gases. Among the findings were these: 1,100° C is the minimum temperature that will produce acceptably hard pellets using carbon monoxide as the reduc-ing gas. Prolonged treatment time improves the pellets' crushing strength, but the rate of improvement falls off sharply after 2 hours' induration. At 1,120° C, 75-percent metallization produces the maximum crushing strength; there was no corresponding peak at 900° or 1,050° C. Sulfur in the furnace atmosphere lowers the required induration temperature. A few tenths of 1 percent sulfur in the pellet increases the sintering rate of metallic iron in pellets by forming a liquid FeS phase that facilitates iron transfer.

Jan 1, 1968

By Clyde L. Holmberg, Paul Zinner

"INTRODUCTION In view of the large tonnage of low-grade iron ore and iron-bearing material known to exist at the western limits of the Gogebic range, the Bureau of Mines undertook an investigation of the area for the purpose of evaluating the iron-bearing formations as sources of iron for possible future utilization.After 6o years of exploration an, development on the Gogebic range, the area investigated by the Bureau represents the known western limit of direct-shipping ore mined from operations on the Gogebic range.An area about 2 miles in length between the villages of Pence and Iron Bolt in Iron County, Vic., was selected for investigation, and trenches wore excavated through the overburden and fully across the iron-bearing formation to obtain 108 bulk samples for beneficiation tests. Exhaustive tests involving gravity and flotation methods, magnetic separation, and magnetizing roasts followed by magnetic separation were conducted on the samples to determine the ammability of the individual formations and the entire iron-bearing zone to beneficiation.Empirical data on the character and mineral content of the formations arc tabulated herein, as well as the results of the beneficiation tests."

Dec 1, 1947

By Gerald T. Homce

A system capable of monitoring mine electrical power systems and detecting impending component .failure could significantly improve power system safety and reduce unscheduled equipment downtime. Such monitoring would require a method of evaluating electrical parameters, calculated from terminal values, for indications of component deterioration. The U.S. Bureau of Mines has targeted electrical failure of squirrel cage induction motors and examined the use of mathematical models to aid in this evaluation. The initial stage of this work is complete, and has produced polynomial networks called adaptive learning networks (ALN's) that can detect and quantify winding insulation leakage simulated on laboratory motors. In this modeling process, empirical data from laboratory motors were used to select the electrical parameters most significant for assessing? motor conditions, and mathematical expressions relating these parameters to simulated deterioration were formed. ALN's developed thus far can process readily measured motor terminal information and quantify power and current levels of laboratory-simulated leakage to within 1% and 3% of full load values, respectively, for motors in the 10-to 150-hp size range. The next stage of this research is validation of these ALN's for actual motor failures; this stage is currently underway, using accelerated life testing of laboratory motors.

Jan 1, 2010

By J. Torma-Krajewski, C. Hipes

Although many mining companies apply ergonomic principles, it is usually done either informally and/or reactively. An example of an informal approach is replacing worn equipment (such as seats) with models that have ergonomic features. Another example is modifying a task to eliminate safety hazards. Such approaches reduce risk-factor exposures that can lead to musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/ equipment after an MSD occurs. However, neither of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper discusses how Vulcan Materials Company applied ergonomic principles and implemented interventions to reduce risk-factor exposures.

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall injury experience for coal mines, both anthracite and bituminous, coke plants, petroleum and natural gas, peat, and asphalt and related bitumens (native); metal mines, their metallurgical plants, including ore-dressing plants and primary nonferrous reduction plants and refineries; nonmetal mines; nonmetal mills; sand and gravel operations; slag (iron blast-furnace) plaints; and stone quarries and their related pants. Volume I of the yearbook contains a chapter showing injury experience and employment data treated separately by metal mines, nonmetal mines, quarries and their related plants, metallurgical plants (ore-dressing plants and primary nonferrous reduction plants and refineries are shown separately), nonmetal mills, sand and gravel plants, and iron blast-furnace slag plants. Volume II contains injury and employment experience in the fuel industries (coal, coke, petroleum and natural gas, asphalt and related bitumens (native), and peat. Injury and employment data are submitted voluntarily for the mineral operations through an industry canvass made by the Bureau of Mines, except for the coal industry, whose reports are mandatory. Information published in this chapter is the result of this canvass. Figures presented in this chapter for 1961 are preliminary except for anthracite, peat, coke, petroleum and natural gas, asphalt and related bitumens, and slag. These preliminary data, with the exception of bituminous coal, are a summation of reports received by May 31, 1962, from the operators showing their injury and employment experience. Estimations of injury and employment experience are not included in these preliminary data.

Jan 1, 1962

By Martin H. Stanczyk

Bench scale, laboratory batch attrition grinding tests were made of a coarse commercial kaolin in a stainless steel, 5-inch-diameter attrition grinding machine to study the effect of a number of basic operating variables on particle size reduction and electric energy consumption. The results of the investigation showed that the more important operating variables influencing the efficiency of kaolin comminution and energy consumption requirements were type, size, and shape of grinding media, grinding media to clay weight ratio, peripheral rotor speed, clay slip pulp density, degree of pulp dispersion, and the angular arrangement of the rotor and stator bars. The tests also indicated that variables having less influence on grinding efficiency and energy consumption were pulp temperature, design of rotor cage, rotor clearance, rotor-stator bar interval, addition agents, pulp level, degree of pulp aeration, and chamber liners. The research showed that grinding media had the greatest influence on abrasion of machine parts and that spherical-shaped grinding media were superior to sharp angular or long bladed media with respect to media degradation, machine abrasion as well as grinding efficiency.

Jan 1, 1968

By Mark S. Sanders

This report presents a summary of the work reported by Sanders and Kelley (1981). A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were indentified. The visual attention locations are contained in this report. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars & scoops were used to test the procedure. Illustrative results are presented in the report.

Jan 1, 1981

By Herman W. Sheffer

This report describes and discusses present-day leaching technology employed to recover copper from low-grade mine and dump materials derived from the exploitation of copper ore deposits in the Western United States. Illustrations of the integral parts of the leaching, precipitation, and recovery operations at several copper-producing companies are presented. Schematic drawings are included to present typical flowsheets of leaching and precipitation operations. Operational problems common to most copper leaching and precipitation plants are discussed. Areas of present and future research to improve leaching techniques are cited.

Jan 1, 1968

A knowledge of the mechanics of wave propagation through the earth is essential if reliable communication systems are to be designed for coal mine environments. To obtain a reliable basis from which accurate propagation predictions could be drawn, a series of theoretical Studies have been prepared for the Bureau of Mines by Mr. Ramsay Decker of Spectra Associates, Inc. through a subcontract with Collins Radio Group. These reports formulate the analytical techniques from which wee may derive frequencies and antenna configurations that yield the optimum signal-to-noise ratios over the greatest distances in mine environments. The reports of sections 2 and 4 deal with analytical techniques for determining the signal-to-noise ratio within a mine environment for loop-to-loop and line source-to-loop antenna configurations. The analytical results of these reports were then implemented into computer programs to obtain predictions concerning through-the-earth signal propagation. These preliminary predictions are based on noise data compiled by Bensema, Maxwell and Stone, and WVU prior to the extensive research conducted by the National bureau of Standards (NBS). These initial measurements indicated a 20- to 30-dB lower noise level than that measured recently by N BS. The recent NBS data is that used by Collins in the final predictions.

Jan 1, 1974

By Jonathan Ludlow

This document is the final report of a study aimed at defining the relative contributions of various sources of respirable airborne dust on longwall faces. In order to define the contribution of various primary sources, continuous dust level data were recorded on five longwalls for an average of five shifts at each. By analysis of these data with records of face activity, it was possible to determine the overall contribution of each of the major elements of the longwall system to overall respirable dust exposure at various face locations. Average levels were determined for roof support generated dust, conveyor and intake dust and for dust levels during various shearer activities. When average levels are compared between mines, a significant degree of consistency is noted. The next phase of the study was aimed at differentiating the various dust sources associated with the shearer. To this end 'fly cuts' varying from 6 in. to 30 in. were closely monitored as were dust levels at operators' positions over the various segments of longwall cycle. These data indicated that the clearance ring of the shearer drum as a disproportionately heavy contributor to shearer dust make. A statistical analysis of the effect of shearer haulage speed on dust make revealed that high haulage speeds are associated with low specific dust make.

Jan 1, 1983

By Thomas L. Vandergrift

To significantly increase the stability of underground excavations while exploiting the full advantages of confined rock strength, methods must be developed to actively control the distribution of stresses near the excavation. This U.S. Bureau of Mines study examines theoretical and practical aspects of rock pres¬surization, an active stress control concept that induces compressive stress in the wall rock through repeated hydraulic fracturing with a settable fluid. Numerical analyses performed by incorporating the rock pressurization concept into a variety of boundary-element models indicate that rock pressurization has the potential to improve underground excavation stability in three ways: (1) by relocating stress concentrations away from the weak opening surface to stronger, confined wall rock; (2) by inducing additional stresses in a biaxial stress field to reduce the difference between the principal stress components near the surface of the opening; and (3) by counteracting the tensile stresses induced in the rock around internally loaded openings. Practical aspects of the rock pressurization concept were investigated through a series of hydraulic fracturing experiments. The use of sulfur as a settable fluid for hydraulic fracturing was demonstrated, although problems related to sulfur viscosity suggest that other molten materials, such as wax, may be better suited to practical field application of the rock pressurization concept.

Jan 1, 2010

By J. M. Pugliese

The Bureau of Mines, in support of its overall goal of helping to meet future U.S. demand for minerals, undertook this study to aid the quarry entrepreneur and/or operator in developing quarries near urban areas. In response to increased environmental concerns, the quarry operator often must take steps beyond those required in the last decade toward gaining permits for quarrying near metropolitan areas. Following the steps suggested in this report should increase the chances to obtain the permits to open and develop a quarry. Each task and question in the general plan flow diagrams are described in detail, with the flow diagrams aimed at the goal of acquiring the necessary permits. The appendixes include (1) types of projects for which Environmental Impact Statements (EIS's) may be prepared and Federal agencies responsible for preparing them, (2) State contacts for information regarding environmental impact assessment requirements and mining and mineral land reclamation laws, (3) a checklist of environmental inventory factors, (4) a tabulation of different regulations that affect mining in Michigan and the number of townships and counties that have each of the listed regulations, and (5) environmental logic associated with site selection. A central recommendation is that the quarry entrepreneur and/or operator coordinate plans at the beginning with local government officials (such as township supervisors and/or city and county planning board members), State and Federal officials, and public groups that will be affected.

Jan 1, 1979

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1979 (October 1, 1978-September 30, 1979) under its Mine Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's miners.

Jan 1, 1979

By Ren G. Dong, Kristine M. Krajnak, Dan Welcome

Continual occupational exposure to vibrating hand tools can damage the neural, vascular and other soft tissues of the fingers. Rat tail models have been developed to investigate the biological responses of the tissues to vibration.1-2 However, the biodynamic response of the tail relative to that of the human fingers has not been characterized. The objective of this pilot study was to compare the transmissibilities of rat tails measured via a scanning laser vibrometer to those of human fingers gripping a handle. Methods In Part I of this experiment, four male Sprague Dawley rats (6 weeks old) were exposed to discrete 5g-rms sinusoids of 32, 63, 125, 160, 250, and 500 Hz. The rats were restrained in Broome-style restrainers with their tails constrained without compression to an exposure platform via elastic straps as shown in Figure 1. The platform was attached to a vertically vibrating shaker. The vibration was measured for the array of points shown in Figure 1 using a scanning laser vibrometer (Polytec) and the transmissibility calculated for each point on the tail relative to the reference points on the platform. In Part II, three male human subjects were exposed at the frequencies specified in Part I - with the addition of 1000 Hz - at a magnitude at the ANSI <0.5-hr limit up to 63 Hz, after which the acceleration was held constant at 5g-rms. The subjects gripped an instrumented handle at 20 N as shown in Figure 2. The transmissibility was calculated relative to the reference points on the handle. [ ]

Jan 6, 2006

By R. A. Kearns

Biennially the Bureau of Mines issues a list of equipment that has been accepted as approved or permissible during the two calendar years immediately preceding the date of publication of the listing. By so doing the mining industry is kept informed of the availability of the latest equipment for safe use underground. This list supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953; Information Circular 7722, Permissible Mine Equipment Approved During the Calendar Years 1953-54; Information Circular 7840, Permissible Mine Equipment Approved During the Calendar Years 1955-56; and Information Circular 7957, Permissible Mine Equipment Approved During 1957-58. This list includes equipment meeting those standards that have been revised since Information Circular 7957 was .issued. Schedule 16E,4 a revision of Schedule 160, was approved May 19, 1960.

Jan 1, 1961

The Federal Coal Mine Health and Safety Act of 1969 limits to 2 milligrams per cubic meter (for dust containing a maximum of 5% quartz) the average respirable dust concentration to which individual miners may be exposed. Section 205 of the Act directs that an appropriate exposure formula for dusts with quartz content in excess of 5% be established. This formula, entered in F. R. Document 70-12351 filed September 16, 1970, is 10 milligrams per cubic meter divided by % quartz. Thus, the total respirable dust exposure permitted limits the quartz to a maximum of 100 micrograms. For example, if % quartz is 5%, 10 mg/5 = 2 milligrams, and (.05) (2 mg) = 100 micrograms. Similarly, if % quartz is 10%, 10/10 = 1, and (.10) (1 mg) = 100 micrograms, etc. If the % quartz is less than 5%, the 2 mg/M3 limit prevails.

Jan 1, 1974

By E. D. Eastman

The basic character of the free energy r data relating to water and the oxides of carbon makes it desirable that the most representative values that can be obtained should be constantly available. The calculations of Lewis and Randall3 retain much of their of original value, but appear to require some modification in the light of more recent work. This paper has been written to incorporate the newer information and to present some estimate of the reliability of the resulting figures. The data upon which the calculations are mainly based are, for these substances, the equilibrium constants of the various reactions involved. The original work relating to these equilibria has, been reviewed and, where possible, weighted to correspond with its probable reliability. The differences in the results of the present from the earlier calculations are partly the consequence of this appraisal and partly of the inclusion of more extensive data, as will be indicated in detail in the succeeding sections.

Jan 1, 1929

By L. A. Neumeier

The Bureau of Mines evaluated the properties of a Zn-0.75 pct Cu-0.12 pct Ti alloy extruded at temperatures between 400° and 720° F. The extrusions were made with a reduction ratio of 28-to-l and at relatively slow speed. Rod was also extruded at 560° and 640° F with a reduction of 255-to-l. With increased extrusion, temperature, extrusion pressures decreased substantially and creep resistance of the rod improved significantly. Coefficients of thermal expansion were low in the long rod dimension. Microstructures, hardness, and tensile properties were also evaluated, and a limited evaluation was made of bend ductility at 32° F for the rod extruded with the 255-to-1 reduction.

Jan 1, 1969