Search Documents

By Wils L. Cooley

The report covers tests and criteria for the establishment of safe grounding systems for coal mines. The work deals primarily with under-ground coal mines, but much is applicable to surface mines as well. Included is an extensive guide to grounding and bonding procedures for mine surface substations. Xit-Rods are evaluated and shown to deviate from manufacturer's claims. An analysis shows that very long cables are difficult to monitor using audio frequency ground-check techniques. A method is developed to detect failing cable splices without removing the cable from service. Simulation and measurement are compared for a technique to detect bad rail bonds, and an assessment is made of grounding techniques for dc face equipment.

Jan 1, 1979

By E. G. Davis

The Bureau of Mines investigated gaseous direct reduction of low-grade iron ore concentrates in a continuous fluid-bed reactor. These studies were made in a 4-inch diameter fluid-bed reactor using hydrogen alone, and oxygen-or air-reformed natural gas as the reductants. The percent reduction is directly dependent on the mole ratio of hydrogen in the reducing gas to the oxygen associated with the iron oxide in the ore. Two-and three-stage fluid bed tests were simulated by repeated continuous tests. The results showed that percent reduction of the final product was dependent on the mole ratio of the quantity of hydrogen in the gas of each stage to oxygen in the iron oxide of the initial ore feed. Reduction as high as 87 percent in the single stages and as high as 94 percent in the multistages was obtained when either hydrogen or reformed natural gas was used as the reducing gas. Magnetic separation and concentration of the highly reduced fluid-bed product yielded a high metallic iron concentrate analyzing 85 percent total iron and 80 percent metallic iron with total iron recovery as great as 90 percent. Agglomeration of the high-grade metallized concentrate produced hard pellets analyzing 85 percent total iron and 78 percent metallic iron. Green pellets, with good strength, were made without any binder in a drum pelletizer. Direct melting of the high-metallic fluid-bed product in a basic lined arc furnace produced a nearly pure iron which contained 0.09 C and 0.01 P with 95 percent recovery of the metallic iron in the metal.

Jan 1, 1972

As part of its research on advanced mining technology, the U.S. Bureau of Mines emphasizes studies on in situ leach mining. This research enables the Bureau to develop technical information that can allow mining companies to adopt in situ leach mining methods. Research results should help to remove the technical and economic barriers currently hindering the development of commercial in situ leach mining operations. This report contains papers summarizing results of Bureau research on various aspects of in situ leach mining. A featured topic is the cooperative field experiment of the Bureau and Santa Cruz Joint Venture in a copper deposit near Casa Grande, AZ. Discussions in-clude an overview of the entire project, cost modeling, environmental permitting, laboratory core-leaching experiments, petrographic studies, and an evaluation of the geologic structure in the region. In addition, papers describe hydrologic modeling and geophysical studies of solution flow during leaching. Preliminary geochemical modeling studies are also summarized. A final paper describes a nonionic chemical additive with potential for significantly reducing the high costs of drilling in in situ leach mining.

Jan 1, 1989

By J. I. Paige

As part of a continuing effort to develop technology that maximizes mineral and metal recovery from domestic resources, the Bureau of Mines investigated a method to totally utilize copper converter slags without recycling them back through the matte smelting furnace. The research was directed toward (1) recovering the contained copper in converting slags by producing a recyclable copper-iron matte, (2) carbothermically reducing the slags to recover the iron, and (3) producing slag wool from the depleted slags. This report deals with the reduction of three industrial converting slags, containing 2.0 to 7.3 wt-pct Cu, in an 800-kVA electric arc furnace to produce a recyclable copper-iron matte. The addition of sufficient iron pyrite to provide 29 to 113 pct of the stoichiometric sulfur (based on producing 40-pct-Cu matte) produced a recyclable matte (36 to 61 pct Cu) at an energy consumption of 520 to 700 kWh per ton of solid material charged. The expected energy saving for treating molten slag in an electric furnace (5-to 9-MVA range) is about 400 kWh per ton of molten slag treated.

Jan 1, 1982

By William R. Vogel

The Bureau of Mines Information and Analysis organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 3291, to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral- material production or consumption.

Jan 1, 1989

By C. Daniel Kealy

Dissolved and suspended solids are present in the free water of tailings ponds. This Bureau of Mines study was designed to identify the influences of the slime zone in preventing these solids from reaching the environment outside the tailings pond. The finite-element method was used to determine the rate of discharge of subsurface water from the Van Stone tailings pond in northern Washington. The slime zone was sampled and tested for the first time, and results were interpreted and incorporated into the mathematical model. Computer results were verified by installing and monitoring piezometers in the field and by a simulated (16- by 1/2- by 3 foot) laboratory model. Output from the numerical model defined critical seepage zones and revealed that proper pond design and maintenance can reduce pond seepage losses to a minimum. Minimization of seepage requires maintaining the pond water level over the slime zone. Sufficient physical, chemical, and limnological data were collected and analyzed to conclude that the only realistic reflection of synergistic effects is obtained by study of the indigenous biota in combination with quantitative chemical and physical data. Proper planning and management of the milling and waste disposal operations are the key to minimal pollution.

Jan 1, 1974

By Burton Scott

A device for detecting carbon monoxide at ppm levels is described which is based on the measurement of infrared absorption at 4.65 microns. The unique feature of the nondispersive infrared instrument is contained in the optical design which includes a confocal cavity, increasing the effective optical path length by a large factor, thus greatly reducing the required package size. The cavity has the effect of reducing the total amount of radiation passing to the detector, but at the same time increasing the percent attenuation observed when adding CO, by a factor called gain. The radiation is chopped by a filter wheel which contains narrow band filters at 4.0 and 4.65 microns. The resultant signal produced by the pyroelectric detector is demodulated by the electronics to product an automatic gain control signal, proportional to the total radiation, and a difference signal, proportional to the CO present. Tests of a breadboard model are described which show cavity gains of 10 with noise levels equivalent to 2 to 10 ppm CO.

Jan 1, 1975

By J. W. Jensen

This report was prepared as a background reference for future publica¬tions concerning the damping capacity of metals and alloys. It contains a broad description of the theory and methods of measuring damping capacity and correlates the developments of the past decade in terminology, units, and techniques. Damping-capacity instrumentation at the Mississippi Valley Experiment Station, Rolla, Mo., is described. The bibliography contains over 150 references to recent articles, each tabulated as to material investigated and test variables, such as frequency, stress, mode of vibration, and temperature. INTRODUCTION After it discovered high-damping manganese-copper alloys before World War II, the Bureau of Mines began research on the damping capacity of alloys and has continued to expand this activity to the present time. In physical metallurgy, damping capacity has become an important research tool in the Bureau. The physical measurement of the damping properties of alloys was begun at the College Park laboratories, and later conducted at Salt Lake City under the direction of Dr. E. V. Potter. Among the many articles resulting from this work, Damping Capacity of Metals (108)3/ has received frequent men¬tion in more recent literature and describes briefly the methods of measurement employed at that time.

Jan 1, 1959

By P. R. Jones

The Bureau of Mines has written a computer program for the design and cost of a shell and tube type heat exchanger, in which a change in phase occurs on the shell side. The total cost, which was minimized, includes the annual fixed charges and annual operating costs. The program was written to meet the following requirements: (1) Triangular pitch, (2) single or multiple pass, and (3) heating or cooling. Price optimum design was obtained for four standard tube diameters and pitch. Standard heat exchangers whose area equaled or exceeded the required area are also listed. The program was made adaptable to various fluids and to various tube dimensions by including many of the required data such as physical properties of the fluids, tube data, and standard shell data as input data.

Jan 1, 1969

By R. H. Grau, S. B. Robertson, J. Dolgos, T. P. Mucho

The National Institute for Occupational Safety and Health (NIOSH) has developed a computer program called the Air Quantity Estimator (AQE). The purpose of the program is to provide a starting point for estimating the air quantity needed to dilute diesel particulate matter (DPM) in an underground large opening mine, albeit taking into account various input assumptions. The AQE estimates the total air quantity needed to dilute DPM emissions that enter the main airstream of the mine to current statutory levels. It helps operators pinpoint vehicles that are high DPM contributors. In addition, it allows the user to make “what if” scenarios by varying the input parameters to achieve the most efficient and practical ventilation system. The AQE is a stand-alone software program that does not require any type of spreadsheet software. Engine data must be known or estimated with some accuracy and assumptions must be made in order to limit the variability of the program output. Program calculations and two case studies, for validation purposes, are included in this report. It should be noted that the program does not ensure adequate face ventilation and personal exposure compliance.

By William Porter

Hand scaling is a physically demanding job and is responsible for numerous overexertion injuries in mining. This experiment studied rib scaling from an elevated bucket to examine force generation capabilities and electromyographic responses to a prying subtask. Subjects exerted force using two bars (steel and fiberglass) at five target heights. Work height significantly affected peak prying force during scaling activities with highest force capacity at the lowest level (p = 0.0188). Bar type did not affect force generation (p = 0.7843): However, use of the fiberglass bar required significantly more muscle activity to achieve the same force (p < 0.05). It was concluded that miners should scale points on the rock face that are below their knees, and reposition the bucket as often as necessary to do so. Additional research is needed to fully understand the impact of bar type on the physical demands of an entire scaling task.

Jan 1, 2006

By L. H. Banning

This investigation was undertaken to obtain basic information necessary for the design and operation of a plant for recovering metallic values from nickeliferous laterite and serpentine of the Philippine Islands. It was divided into three parts: (1) Mineralogical studies and preliminary mineral dressing tests; (2) electric smelting of the ores, upgrading of ferronickel by blowing with oxygen, smelting laterite slag to produce crude iron, and the production of mild steel; and (3) nickel and cobalt recovery from upgraded ferronickel. Results of the investigation indicate that it should be feasible to recover nickel, iron, and possibly cobalt products from the laterite and ferro-nickel from the serpentine. Mineralogical studies were made on representative fractions of the laterite and serpentine tonnage samples and on five selected samples; mineral dressing tests were made only on laterite. The nickel occurs principally associated with hydrous iron oxides and chemically combined with serpentine; garnierite was the only discrete nickel mineral identified, and it was found in a highly decomposed serpentine. The bulk of the cobalt was found in wadlike manganese oxide material. Approximately twice as much chromite was found in the laterite as in the serpentine, By mineral dressing techniques, laterite was separated into two fractions: one fraction contained over 90 percent of the nickel and cobalt, and 83 percent of the iron; the other fraction contained 74 percent of the chromium. A cobalt concentrate (1.1 percent Co) was produced by a scrubbing and sizing procedure.

Jan 1, 1962

By L. D. Tracy

This is the third of the series of reports on coal-mine royalties and leasing conditions in Illinois. The results of the study of District VI were published as Serial No. 2726, January, 1926, and those of District VIII as Serial No. 2745, April, 1926, of the Bureau of mines. The counties of Macoupin, Sangamon, and Montgomery, which are three of the principal coal-producing areas in the northern part of District VII, have been chosen for this report because these counties cover an entirely different part of the State than do the two districts already covered. Some leases in, Randolph and Washington counties are included as they are in the southern part of the district, and the data happened to be readily available.

Jan 1, 1926

By Richard L. Fowler

Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the beam coverage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve a completely self-contained shuttle car system which responds to the existing mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to evaluate various guidance techniques during the feasibility study. Subsequent simulation runs were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing was performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated the predicted performance capability during underground face haulage tests. Dust did not impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance. Closed loop steering control with manual override is recommended for the lateral guidance system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.

Jan 1, 1973

By Parviz F. Rad

The Bureau of Mines used a linear cutting apparatus equipped with a 7-inch disk cutter to cut grooves in marble, limestone, granite, and quartzite under a normal force of 7,000 lb. The size distribution of the muck for various grooves was determined through sieve analysis. A statistical search showed that Weibull distribution describes the size distribution better than other available functions. Results indicate that fineness modulus, chip population, and dimension of the largest chip can be used as indicators of cutting efficiency. The results correlate with those obtained from the boring machines and other lab experiments. Application of the principles established through this work to the operation of boring machines is explained

Jan 1, 1974

By David C. Grant

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated.

Jan 1, 1985

The purpose of this study was to examine the problems of underground coal mining in the United States, and to develop recommendations for an integrated Research and Development Program aimed at resolving these problems. Specific objectives of the study were as follows: ? To identify the existing inadequacies that have adverse effect on Health, Safety, External Environment, and Productivity. ? To identify opportunities for technological advance s to correct these inadequacies. ? To develop an integrated Research and Development Program designed to accomplish the advances identified. Many of the recommended tasks are dearly long range; this is especially true of those for study of future mining systems. However, funding recommendations in this Report are presented for a 5 -year period, since the developments accomplished during this period will undoubtedly be a factor in the formulation of the follow on tasks. Where applicable, the recommended Research and :Development could include development and test of pilot model equipment.

Jan 1, 1970

By Paul Meadows

This Bureau of Mines report presents operating practices and results of pressure maintenance and secondary recovery by water injection or by water injection supplemented by gas injection. Particular emphasis is placed on the results of water injection, which is the principal oil-recovery method employed in projects covered by this report. No attempt is made to study gas-injection projects or operations that are considered water-disposal projects. Also, this report does not include water-injection projects that have not been in operation long enough to evaluate results. Figure 1 is a map of north Louisiana showing the geographical locations of the projects included in this report. Most of the data used in this study were supplied by unit operators, operating companies, and the Louisiana Department of Conservation. Reservoir information and recovery data are generally those supplied by the operators, but include revisions where deemed necessary.

Jan 1, 1962

By Richard F. Hewlett

The purpose of this Bureau of Mines paper is to provide the mineral industry with current information on high-speed data processing and to illustrate how some of these techniques can be applied to the industry. The need for applying these techniques is generally recognized, but not much information is readily available on specific applications. This paper briefly describes high-speed data processing and reduction equipment in an effort to familiarize the reader with the functions of the equipment. A list and explanation of some of the possible applications of high-speed data processing for the mineral industry are included. A few of these applications are illustrated by the use of specific examples of existing computer programs or processing methods, including their calculation times and costs. Some of the programs cited herein were developed by the author at the University of Arizona for a Masters thesis in mining engineering. When a reference is made to a specific computer, the reference is given to make the information that is being presented as factual as possible; most of the manufacturer&apos;s equipment that is mentioned in the references was available at the University of Arizona, and no specific endorsement of that manufacturer is intended.

Jan 1, 1962

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, rooting granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of rooting, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural tines available. On the other hand, California manufacturers of asphalt products other than having utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, and other nonmetallic minerals as filler, mainly for reeling and flooring. Also about 500,000 tons of roofing, granules is produced in California, most of which goes into roofing manufacture in California. In addition. A significantly large and growing tonnage of relatively coarse mineral aggregates Ire used on low-angle, built-up, asphalt roofs to produce in attractive surface and offer protection against the clements. Clearly ill minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of those commodities could be utilized in some use categories.

Jan 1, 1966