Search Documents

By Rob Farnfield, Charlie Adhock

The measurement of near-field shock has always been an attractive proposition for those working in the field of explosive and blast performance. The most commonly employed technique involves the use of piezoelectric accelerometers. Although highly effective, these complicated devices are relatively expensive and are often destroyed in the blast event. This paper describes the development and field-testing of a shock sensor of sufficiently low cost to enable it to be routinely used in product blasting. This new device is based on piezoelectric wafer technology and does not require any external signal conditioning. The device is housed in a small cylindrical package with approximate dimensions of 30mm (1.2”) length and 5mm (0.2”) diameter. It has been determined that the most effective way of fixing the device to rock is in a small diameter hole with epoxy glue. Alternatively the sensor can be simply placed in holes filled with either water or bulk emulsion explosive.

Jan 1, 2005

The first principle one usually Learns about blasting is that cunpetence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced blaster when operating in a new area, may have to make one or two shots just to acclimate himself to the new conditions with which he is faced.

Jan 1, 1989

By Tom Short

"Construction blasting covers a very extensive variety of explosive applications. I will discussseveral of these with you and then show slides from my collection, starting in 1956, which will betterillustrate the types of blasting under discussion."

Jan 1, 1991

By H G. Bosmare, G Bedser, C V. B Cunningham

Peak Quany has achieved substantial improvements to its bottom lie by giving close attention to blasting practice, and in pr@icnlar by introducing electronic delay detonators for routine production blasting. The precision and flexibility provided by these units has enabled the quarry to gain control over fmes and curtail oversize without increasing explosive usage. In addition, the extent of nuisance from blasting vibrations has been reduced.

Jan 1, 1998

By Ann Barron

For millions of people, cold weather is a fact of line – and one that can make a major challenge out of just getting to work. But for those working in the blasting industry, a number of obstacles are created when old man winter blows in. In addition to the obvious concerns regarding personal protection, Mother Nature can throw some very nasty weather at the blasting crew trying to travel with explosives products from the magazine site to the job site. As such, divers need to be familiar with cold, ice, and snow driving conditions both on and off the blast site. It’s critical to know what to expect before you leave. Keep informed of the latest weather and road conditions as they change often; it will help you make the right choice in clothing and driving habits. Remember bridges and overpasses will freeze first even in temperatures above or near the freezing mark due to the effects of wind chill. Plan to take extra time to and from the job site.

Jan 1, 2004

By Jennifer Ward

The primary objective of this paper is to establish how a low cost, high definition (HD) camera can allow for easy sustainable recordings of blasting operations. The subsequent analysis of each video can be utilized to monitor what type of performance was achieved and aids in improving blasting performance.

Jan 1, 2015

By Shazad Hosein, William Birch, Douglas A. Anderson

This paper will present the results of tests of a new method for assessing explosive performance using wavelet transform analysis of standard blast seismograms. The theoretical background of the method was presented at an earlier ISEE conference.

Jan 1, 2015

By B Brown, P J. Hommert, B J. Thorne

"Early attempts at estimation of stress wave damage in blasting by use of finite element analysis met with limited success due to numerical instabilities that prevented calculations from being carried to late times. A"" improved damage model based on microcrack growth in tension allows finite elementcalculations which remain stable at late times. Estimation of crater profiles for blasting experiments in granite demonstrate successful simulations with this model."

Jan 1, 1990

By Jay Rodgers

There has been a longstanding acceptance that burden plays a major role in the magnitude of ground vibration amplitudes generated from surface blasting. Much of the data that this belief is based upon is empirical in nature and may or may not represent an example of false inference. Recent published reports have rightly questioned the influence of burden and confinement on blast vibration amplitude, suggesting that the fracture condition of the rock mass is a better indicator. The increased investment in electronic detonators as a tool to control ground vibration amplitudes demands an understanding of vibration production detailed enough to make use of the vastly improved timing accuracy that they provide. A more accurate relationship may be found if we strip away the assumptions of the past and search for the underlying mechanism of vibration production in surface blasting. We must answer the question: What happens at or near the borehole when an explosive charge detonates that produces ground vibrations?

Jan 1, 2003

By Braden Lusk, Tristan Worsey, Nathan Rouse, Kyle Hall

Loading explosives up hole has challenges that are typically not seen in down hole explosive loading. Most explosives applications are not up hole. Lack of experience and technology can cause significant problems when loading explosives up hole. When results aren’t achieved, the blame is commonly put on the design when the true problems are unknown. Not knowing the cause of the problem causes drill and blast designs to be over engineered and very costly with little success. Being able to know and record key data is crucial to actually solving the problem. This paper goes over blast instrumentation that can be used to trouble shoot drill and blast problems in up hole explosives loading in underground mines. The tools and procedures used to trouble shoot include velocity of detonation recorder, borehole tracking, seismographs, and borehole camera. Each item will be discussed in detail with a case study to show the usefulness of the instrumentation. The operation discussed in the case study had issues pulling raises and had hang ups in the stope shots. These problems caused production slowdowns and costly remediation blasting that was not very successful. The case study is an underground gold mine that used modified sub-level caving with backfill as the mining method.

Jan 1, 2018

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of "ore. accurate detonators. The new and "ore accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1989

By Matt Slezak, Tristan Worsey, Nathan Rouse, Kyle Hall

As everyone knows, blasters are required to file blast reports of every blast for regulatory purposes. To this day, the authors see many handwritten blast reports. Handwritten blast reports are notorious for containing errors or omissions. This is not because the blaster intends to misreport information. It is because blasters have many tasks to complete in a day, are sometimes in a rush, and could accidentally miscalculate data, omit items, or record incorrect data. In most cases, blasters do not suffer consequences to these errors because blast reports are seldom reviewed in detail. In some cases, such as when a blasting operation undergoes some sort of litigation process, the reports are reviewed in detail and the blaster is ultimately held responsible. If the reports contain errors, the blaster can be fined, have his/her license revoked, or worse. Electronic blast reporting and centralized data management can help reduce or eliminate the potential for accidental blast reporting errors to occur. This paper presents many ways that electronic blast reporting can reduce or eliminate blast reporting errors, decrease time and extra costs spent reporting, and improve efficiencies in the field and the office.

Jan 1, 2018

By Hae-Moon Choi, Sang-Don Lee, Chang-Ha Ryu

The purpose of the study presented in this article is to establish a standard blast pattern to yield optimum blasting performance along with an attempt to reduce a difference between design and construction. A series of test blasts were carried out at two tunneling sites of Central Inland Highway crossing in Korea. Long-hole blasting was tested in rock mass whose RMR value is over 60.The blasting results were evaluated by measuring degree of fragmentation, advance rate,muckpile distribution, overbreak, etc. Based on the results of test blast, several patterns were proposed for a two-lane highway tunnel.

Jan 1, 2006

By John Meuth, Brandon Fryman, P. E. Hoffman, Joshua Ph. D., P. E. Calnan, Josh Ph. D.

Quantitative Risk Assessment (QRA) can be specifically tailored for use by the commercial explosives industry to calculate risk to employees and the public from commercial explosives facilities and operations. This methodology has several advantages over the American Table of Distances (ATD) which is solely a Quantity Distance (Q/D) analysis. While the ATD has remained essentially the same for 100 years, the safety of commercial explosives in storage has increased immensely. However, the concepts behind QRA calculations are not as intuitive and even at the end of the calculations the values of risk must be compared to something. A few regimes for assessing an acceptable level of risk are discussed in this paper. Risk levels for various United States Federal entities and international agencies are highlighted and suggestions for acceptable risk criteria for individuals and groups are provided. Referencing risk levels from normal daily activities is also done in this paper to make relative the accepted risk criteria. This paper presents some relevant individual risks for everyday activities and some scenarios for group risk for comparison. Individual risk is a straightforward concept however group risk is more complicated. This paper aims to clarify these concepts and provide means to communicate them to the public.

Jan 1, 2019

By N/A N/A

Aw a rd winners from the University of MissouriRolla. Back row from left: Seok Bin Lim, Chris B o l l i n g e r, Adam Kre s l e r, Scott Geer, Joseph Cohn, and James (Buck) Hawkins; Front ro w f rom left: Dr. Worsey, Trish Robertson, and Fio G i a n a

Jan 1, 2004

By William G. Szymczak

A set of experiments were conducted at the Aberdeen Proving Grounds [1] in which explosive charges were buried in saturated sand beneath a suspended rigid platform. The goal of these experiments was to measure the dependence of the impulse transmitted to the platform on the standoff distance and the charge burial depth. Simulations of these experiments were performed using the BUB2D axi-symmetric code using a frictional-cohesive visco-plastic model to describe the response of the saturated sand. This code solves a constrained set of conservation laws in which the liquid region (in this case saturated sand) is assumed incompressible. The explosion is initialized as a high pressure gas bubble (void) within the fluid. Comparisons of the simulations to the experiments are presented together with a study of the physical phenomenology associated with the loading process. In particular, it is shown that the force imparted to the platform is a combination of the impact of the sand on top of the explosion gas bubble and the pressure of the bubble as it expands before venting into the atmosphere. Under certain conditions, when the platform standoff is sufficiently small and the platform is sufficiently large, the bubble can over-expand before venting and pull the platform downward. This phenomenon was studied further through carefully measured and photographed small-scale experiments performed at the University of Maryland [2]. The small-scale experiments provide additional important validation benchmarks for our model.

Jan 1, 2005

By Kenneth Eltschlager

Business says that location is a primary component of being successful. So too is the importance of location in blasting. For blast seismograph data to be useful, the location of the blast and seismograph must be clearly documented. Another location of importance is that of a nearby structure. Establishing the spatial relationships between the blast, seismograph and nearby structures, allows the blaster to correctly interpret the data, evaluate the performance of the blast and gauge the validity of any complaints.

Jan 1, 2004

By Dale S. Preece

"Detonation delay timing has been an important aspect of quality rock blasting for decades. Detonators that enable delay timing have improved over the years especially with the recent advent of precision electronic detonators. The positive effects of precision delay timing have been observed repeatedly in the field with improved fragmentation, heave and overall blast control. Three-dimensional computational capabilities in terms of software, material models and computer speed have recently made possible the computer simulation of multiple blast holes in a bench configuration with precise delay timing between holes. Some of the key physical phenomena enabled by precise delay timing include: 1) collision and interaction of stress waves produced by adjacent blast holes, 2) reinforcement of stress waves from multiple holes as they reflect from the bench face and ground surface, 3) reflection of stress waves from “dynamic free surfaces” created by previously detonating holes, and 4) deformation induced fracturing, cracking and fragmentation. Simulating rock blasting in 3D has shed light on the physics involved and is resulting in an evolution of our understanding of fragmentation mechanisms. Routine use of these 3D computational tools will result in a much better understanding of the complex physics set in motion by the rock blasting process and allow predictionof improved blasting."

Jan 1, 2009

By Rufus Flinchum

Two of the most critical concerns a blaster faces today are airblast and flyrock. Airblast, sometimes called noise or overpressure, can cause damage to neighboring structures, especially windows. It also is the cause for many vibration complaints. The human sense of hearing is often more acute to identifying source than the sense of touch. When a blast occurs, the airblast is what identifies the event. The vibration that may be felt is then associated with the airblast. Vibrations of greater magnitude, such as passing trucks or construction work on the house, go unnoticed because their sounds are familiar or expected. Flyrock is the number one killer and cause of damage. Elasting laws provide limits for these two concerns. Failure to comply may result in fines, closing of the operation, and even prison. Airblast and flyrock originate from two distinct areas, the open face and the bench surface. Each of these areas is addressed in the detailed proven procedures that follow, and if used by the blaster in conjunction with his own blasting knowledge, a sound blasting plan can be developed to minimize the occurrence of airblast and flyrock.

Jan 1, 1992

By Tom Treleaven

Several nonelectric blast initiation systems have been developed since the mid 1970's. Until that time, most blasts were initiated either electrically with electric blasting caps or nonelectrically with detonating cord. What the development of these new systems was attempting to accomplish was to provide a system that was nondisruptive to the stemming or explosive column, but still possessed the safety and flexibility inherent in nonelectric systems.

Jan 1, 1991