Search Documents

By Sushil Bhandari

Presented here is the simplified process of fragmentation of homogeneous rocks by blasting based on experimental studies. Small scale single hole blasting experiments on jointed limestone are described. Results show that directions of joints overshadow the degree of fragmentation and also influence the remaining rock. The possible influence of joints on the process of fragmentation of non-homogeneous rock by blasting is also discussed.

Jan 1, 1983

By France Goupil, Richard Barabe

In 1987, a large company reopened its quarry located in a very dense urban area in Montreal-East. This reopening occurred after a long period of inactivity during which houses were built within 200 feet of the quarry. During the first year of operation, people in the vicinity reacted negatively which caused the City of Montreal to seriously consider closing down the quarry by expropriation. This expropriation would have resulted in millions of dollars of loss for the operator.

Jan 1, 1992

By Charles E. Joachim, Christo V. Lunderman, Charles R. Wdch

The U.S. Army Engineer Waterways Experiment Station (WES) recently conducted a series of precision-scale water shock experiments which consisted of the detonation of several 8-gram, 10-gram, and 12-gram spherical explosive charges. The charges were fabricated from NAX 2000 Primasheet explosive and were center-detonated. Commercial tourmaline crystal water shock sensors were used to measure the induced pressure fields in the water. The measured water shock waveforms and related parameters from the precision-scale experiments were in general agreement with data from larger-scale experiments.

Jan 1, 1998

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d'Or, Québec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By John M. Bolger, Keith E. McMaster

Excessive salt fines are undesirable in underground salt mining as they are considered a costly waste by-product. This paper describes an extensive explosive application program conducted at The Canadian Salt Company Ltd, located in Pugwash, Nova Scotia, Canada. The prime objective of the program was to reduce the quantity of fines generated from this company's underground production blasts. The program was known as the "The Fines Reduction Program".

Jan 1, 1996

By Jeff Wachendorf

As the title implies, this paper details the start of a cast blasting and the design flexibility required to satisfy different parameters encountered on a large coal mine employing cast blasting as the program has grown and evolved around the town of Colstrip, Montana. As strip ratios have increased, the need to adapt and find solutions to provide coal at a reasonable cost to the mine mouth power plants has risen. Colstrip, Montana has a long history of coal mining which dates back to the early 1920s when Foley Brothers began supplying coal strictly for powering locomotive engines.

Jan 1, 2015

By Kenichiro Yamamoto, Masaharu Murakami, Toshio Matsuzawa, Yoshiyuki Ikeda

In a series of tests, we examined the dynamic shock resistance of Emulsion Explosive in water and compared it with that of Dynamite and Slurry Explosives. Both the distance between donor and acceptor charges and the delay initiation timing of the acceptor charges were varied. The resistance to dynamic shock varied with the properties of the explosive. In the case of emulsion explosives, there seems to be a certain proportional relationship between the critical detonation distance and the delay initiation timing. Some blasting results with emulsion explosives are described.

Jan 1, 1983

By C De La Cruz

The use of a thin-film piezoelectric stress gauge to determine the pressure profile in a detonating explosive has been demonstrated. These PVDF gauges have measured, in the borehole, the Chapman-Jouget pressure and the release adiabat of the detonation products for several explosives including ANFO and ANFO/emulsion mixtures. The technique can provide: (1) a direct measure of the blasting stimulus, (2) a sensitive QA tool for the blaster, and (3) a means to examine the magnitude and effects of preshock from adjacent bore holes. The PVDF pressure gauge is self powered, can measure pressure from a few bars to 400 kbars, has high time resolution (0.05 µsec), and is easy and economical to use.

Jan 1, 1997

By Finn Ouchterlony, Gert Bjarnholt, Robert Holmberg

A system for contour blasting with a linear shape charge principle has been studied /10/. In one operation the charge creates two notches along the bore hole wall and breaks the rock mass. The built in notching capability makes it possible to reduce the specific charge and the bore hole pressure to 1/3 of what is used in conventional contour blasting and to ensure that cracks are initiated and propagated only at the notches and nowhere else. The notching capability of linear shape charges has been studied experimentally and the bore hole pressure calculated to aid in optimization of a charge for future field experiments in bore holes with a diameter of about 50 mm.

Jan 1, 1983

By Robert A. Cortese, Lon D. Santis

This paper describes a method of measuring continuous detonation rates using standard electronic parts, coaxial cable, and a data recorder such as an oscilloscope. Three six-volt lantern batteries or a DC supply power the electronics that cost less than $100. Included are means of showing low battery power, finding the proper voltage scale on the recorder, and test triggering of the recorder. Modifications of the circuit allow for use in the field to measure charges up to 57 meters and for use in the laboratory to measure short charges. The high resistance (8.709 Ohms/meter) coaxial cable is a mass produced, special order cable available commercially. The driver circuit delivers a constant current to the cable, and as the detonation shorts the cable, a change in circuit voltage occurs. Recording this voltage change over time allows determination of detonation rate resolute to the sampling speed of the recorder. An oscilloscope or personal computer with a data acquisition card can easily record the data for analysis. Detonation rates recorded in the laboratory using the coaxial cable and the Bureau of Mines's traditional probes are presented. The system accurately measured the detonation rates of ANFO confined in steel pipe, detonating cord, and unconfined high explosive.

Jan 1, 1996

By Malcolm Mellor

Practical procedures that have been developed for pre-split blasting and smooth blasting in common rocks are reviewed systematically. Topics covered include shothole spacing, charge weight per unit length of shothole, decoupling ratio, adjustments for explosive type and rock type, and weight of explosive per unit face area. Relevant properties of frozen rocks, frozen soils, and ice are compared with those of common unfrozen rocks, and appropriate adjustment of blast design is discussed. Interim relationships for the design of controlled perimeter blasting in frozen soils and massive ice are put forward, recognizing that additional experimentation is required. Special problems in controlled blasting of ice are discussed. These include effects of wet holes, delayed removal of burden, and submerged burden. Special attention is given to the cutting of ice islands and icebergs. An Appendix describes an operation in which the face of an ice wharf at McMurdo Sound was trimmed by pre-split blasting.

Jan 1, 1976

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By Greg Mclellan, Mark Johnson, John Pepper

Several large quarrying projects recently occurred in Miramar, Florida. These were closely monitored by the Seismologist of Record and Broward County in accordance with County and City regulations. In addition to this monitoring, the City of Miramar employed The Pepper Engineering Group, Inc., to provide additional spot check monitoring and to review the records of the other two parties on a routine basis. Broward County ordinances require that the location of each shot and the nearest protected structure be recorded along with seismograph measurement of each shot at the nearest protected structure. The positions of the blasts and nearest protected structures were determined using GPS. The blast vibrations were measured by seismograph. Over 600 shots, which are the subject of this study, were measured both by the County, the Seismologist and, on many occasions, The Pepper Engineering Group. As such, the vibration data was constantly cross-checked for consistency. The blasting contractor also provided blast designs for each shot. In this paper, the measured vibrations are plotted in terms of Resultant Peak Particle Velocity (RPPV) versus Scaled Distance (SD) on logarithmic scales. The data curves are fitted with least squares and upper 95% and 99% prediction limits are provided. Equations are presented to predict the RPPV based on scaled distance and prediction level using power fits. Statistical information concerning the derivation of the various limits is presented. The raw data used to develop this paper, along with other information concerning the shots, will be posted on the Internet for use by other researchers.

Jan 1, 2000

By Terry Nichols, Karl E: Warkwick Burgher, Charles J. Wideman

The application of Fourier spectral analysis to records of ground vibration generated by over 100 explosions from an open pit mine is used to develop empirical predictor equations that relate the response spectra to the blasting parameters used to generate the excitation motion. Time series representations of ground particle velocity are transformed into the frequency domain where the appropriate modifications are made such that the inverse Fourier transform yields the time series representation of particle displacement and acceleration. Compensations are made for the transform function of the recording system in the frequency domain. Spectral analysis of the three types of ground motion is correlated with the blasting parameters. The results show that the frequency content of ground vibrations generated from a mine blast can be quantified in terms of the predictor equations.

Jan 1, 1990

By A. K. Sirveiya

A major concern with blasting at surface mines is generation of ground vibration, air blast, flyrock, dust & fume and their impact on nearby structures and environment. A study was conducted at a coal mine in India which produces 10 million tonne of coal and 27 million cubic meter of overburden per annum. Draglines and shovels with dumpers carry out the removal of overburden. Detonation of 100 tonnes of explosives in a blasting round is a common practice of the mine. These large sized blasts often led to complaints from the nearby inhabitants regarding ground vibrations and their affects on their houses.

Jan 1, 2005

By Paul Worsey, Braden Lusk, Seokbin Lim

This paper discusses the theory and experiment involved in the discovery of the mechanisms of Linear Shaped Charges, which are much different from those for Conical Shaped Charges. Linear Shaped Charges (LSC) have been assumed to function in the same manner as Conical Shaped Charges (CSC) in the published literature on the subject. Much work has been done on CSC for military purposes, but there is limited information about the mechanics of LSC. Previous theories have cited the formation of a Monroe Jet as the dominant process. The Monroe Effect describes what happens to a target below the charge following detonation of the charge, and prescribes a fluid jet process for penetration. The fluid jet comprised of the liner material is the cutting device in CSC and has been extensively studied. Recent work at the University of Missouri at Rolla (UMR) cutting concrete with LSC has surprisingly shown that there is not a fluid jet process in LSC. After completing several reinforced concrete penetration tests, minimally deformed copper blades were found in the debris. Initially, the blades were suspected to be misfires or malfunctioned charge remnants. However, results were good and blades were found after every single test. Upon closer inspection, the ribbons were found to be folded copper and they were suspected to be the bottom liner of the LSC. A test series was conducted to verify the new theory by experiment.

Jan 1, 2005

By Charles E. Joachim

Railroad and blast induced vibrations were measured in the vicinity of the proposed Big Bend Cutoff. Peak horizontal and vertical particle velocity relations were developed using least squares regression analysis. The dominant frequencies of these data are in the range of 30 to 50 hz. Therefore, allowable charge weight per 30 msec delay curves were generated for buildings (2 in./sec) and unlined tunnels (8 in./sec). A blasting contour map is presented for this site.

Jan 1, 1984

By Yves Lizotte, Malcom Scoble, Sanu Hanspal

"This paper reviews the physical, chemical and mechanical components of what is considered to be the anatomy of a blast muckpile. These relate principally to geometry, floor, fragment size and shapedistribution, density, hydrology, weathering, and diggabiity characteristics."

Jan 1, 1995

By Dale Preece, Stephen Chung, D. Scott Scovira

The DMC_BLAST (Distinct Motion Code) has been developed to model rock motion and displacement during the gas expansion phase after the detonation of an explosive in a borehole. Recently, a designated delay firing order algorithm was written into the DMC_BLAST code. The model can now be used to analyze rock mass displacement for a V-cut, center opening, or sinking cut initiation sequences. This new feature allows the investigation of the effects of delay firing order on rock displacement when blasting complex inter-bedded and ore-waste structures. The model provides important ground movement and mixing indicators for dilution control in surface gold mining relative to the initiation sequences employed. Echelon blasts as compared to center opening type blasts show differences in their internal muckpile displacement. These displacement differences can be important to operations that mine narrow strike driven ore bodies. The model also has applications to through coal seam blasting and demonstrates that down-dip blasting is a better alternative than up-dip blasting. There is less disturbance to the dipping coal seam and less mixing of the rock and the coal.

Jan 1, 2000

By Mark William Withey

Blasting safety in surface mining is a necessary industrial goal. Proper techniques and disciplines exercised during the blasting process enhance the probability of achieving that goal.

Jan 1, 1995