Search Documents

By Mark S. Stagg, Rolfe E. Otterness, Stephen Rholl

The Bureau of Mines is engaged in research to develop and test high explosive fracturing and rubblization techniques that will enhance ore body permeability and thus increase recovery during in situ mining. The natural permeability of many ore bodies is too low to allow successful in-place leaching. These deposits could be profitably mined if flow rates of leach solutions could be increased. Blasting represents a potentially low-cost and effective permeability enhancement technique.

Jan 1, 1991

By George E. Jackson

ANFO, as a blasting agent, is used in large quantities in coal surface mines. It can be purchased on the open market or through reliable suppliers. The blaster in the field must assume that his ANFO is homogeneous, consistent, and nearly identical on a daily basis. A quality control program will enable him to be assured of the correct product. Therefore, the material cost and operational efficiency can be better controlled.

Jan 1, 1978

By Alastair Torrance, George Boucher, Roger Keller

An investigative blast programme has been carried out to provide information on the best blasting methods to excavate Chek Lap Kok island in Hong Kong for the new airport. The objectives of the programme included the assessment of a range of blast design parameters and their influence on fragmentation. This has been evaluated by physical assessment, photo digitising of the muckpile and computer predictions. In addition, a model to predict the three dimensional muckpile shape has been successfully calibrated.

Jan 1, 1992

By Mauro F. Dobran

The use of Slot Raises has been common for many years. The following presentation will compare various methods of developing these Slot Raises and introduce two new ones.

Jan 1, 1996

By Ivan Kovac, Pero Marjanovic, Branko Bozic

"The paper deals with results of geophysical survey of the rock masses, and the blasting parameterswhich have effect on the fragmentation in quarries . A relationship between the burden, which is the distance between the charged borehole and the free rock surface, and the velocity of longitudinal waves in the rock mass is established based on measured values for different quarries. It is shown that the drilling geometry can also be detemrined from this relationship."

Jan 1, 1999

By Mark S. Stagg, Stephen A. Rholl

The Bureau of Mines is studying blast delay timing influences on rock fragmentation in a series of tests that started in 3-ft concrete blocks, progressed to 45in-bench reduced-scale tests in massive dolomite, and has now included 22-ft-bench full-scale tests in a thin-to-thick horizontally bedded dolomite. This paper discusses the full-scale test results and how they compared to the concrete block and reduced-scale studies.

Jan 1, 1988

The breakage mechnism of a spherical charge greatly differs from that of the cylindrical charge used in underground mining. The advantages of the spherical charge could not be utilized until INCO Metals Company, Ontario Division, introduced large diameter holes to their operation.

Jan 1, 1978

By Jack Eloranta

This paper describes a method of evaluating shot performance through the use of available mine- data. The mine had already been monitoring the following parameters for other purposes: drill penetration rates, shovel loading rates, crusher throughput, crusher power and crusher hangups. By assigning pit coordinates to these factors, maps showing the location of difficult and favorable blasting are as are identified. Products and techniques are compared by the same method.

Jan 1, 1993

By Roger L. McCarthy, Ali Reza

The use of an ammonium nitrate-fuel oil (ANFO) explosive in the Oklahoma City Federal Building bombing has led to a renewed interest in using additives during the manufacturing process of ammonium nitrate to render it non-detonable. Suggested additives include calcium carbonate, which is already used in some European countries, and mono-ammonium phosphate (MAP) or di-ammonium phosphate (DAP), which are the primary desensitizing agents claimed in US patent 3,366,468, Method for desensitizing fertilizer grade ammonium nitrate and the product obtained, issued Jan. 30, 1968 (Porter, 1965).

Jan 1, 1999

By Pat McLaughlin, J R. (Dick) Daniels

Current practice in establishing quarries in remote areas with hilly or mountainous terrain tends to the use of airtracs (or similar pioneering units) drilling horizontal holes to establish a face, followed by bench development with light excavating equipment. The authors propose the use of a hybrid coyote blast design that incorporates long-round tunneling techniques. This method would, in effect, use down-the-hole (DTH) drills to advance the drift cut to the final depth, allowing longer and more rapid drift advances, and replace the cross-cut drifts with clusters of DTH holes to achieve the same explosives distribution.

Jan 1, 1995

By Calvin Konya, Janos Foldesi

A bridge over a main line railroad system was scheduled for demolition. The bridge was made of reinforced concrete and spanned three mainline railroad tracks which could not be shut down due to blasting or demolition. To further complicate matters, the mainline tracks had high tension power lines running above the tracks, but below the bridge. These high tension wires provided the electricity for electrically powered trains. The tracks could not be damaged or disrupted, nor could the power line be broken.

Jan 1, 1992

By Abraham Lindo

Panama’s current economical growth demands an increase in electric power supply; projected energy supply for 2012 exceeds the demand by as little as 2%. In an effort to comply with the demand, several different hydroelectric projects, promoted by the government, are currently under construction and each of them vary in generating capacity, construction design and complexity.

Jan 1, 2013

By Rodney C. Espley-Jones, John C. B Wilson

South Africa is well known for its shaft sinking exploits, and many of the world's biggest and deepest shafts are to be found there. Blasting practice differs in a number of respects from that followed elsewhere.

Jan 1, 1979

By William H. Snyer, Hank Cox

A high explosive device using Linear Shaped Charge (LSC) (to rapidly cut vent and drain openings in a rail tank car) is described. In the event of damage to a tank car loaded with a pressurized flammable fluid, it may sometimes be necessary to perform controlled on-site vent, drain and burn operations. Existing techniques required refinement to achieve the desired safety and procedural reliability for use in emergency situations.

Jan 1, 1994

By Randall M. Wheeler

Many blasting companies are using simulated production ground vibration waveforms to aid them in the control of their vibration effects. The simulations are typically produced by using a seismograph to record a signature waveform from a single hole shot and subsequently applying the various delays to be used in a proposed production design. The ability of this simulation method to give good results usually depends on three primary factors. These are: 1) the homogeneity of the seismic travel path from hole to hole; 2) the consistency of the seismic energy release per unit of explosive from hole to hole; and 3) whether or not the delays fire as planned.

Jan 1, 1991

By J Foklesi, G Bohus, D Benedek

The breakage process in blasting takes place in space and in time and the latter will determine the degree of fragmentation, shape of the muckpile and the extent of displacement. The shock wave travels at the velocity of sound in the material and it can easily be measured. The cracks' velocity is only 0.38 % of the velocity of sound. The number of cracks at any distance from the explosion cavity, their length and the time of development can be calculated.

Jan 1, 1986

By James Stuart

Explosive components are common in electric power distribution systems. Basically, we use explosives either to open or to close a circuit very quickly, in order to avoid electrical catastrophe. We use explosives in these important applications, because explosive materials are compact, inexpensive, long-lived, powerful, and can be triggered instantly. A lead-alloy fuse will melt when excessive electric current passes through it. A small fuse of this type melts quickly. However, a lead-alloy fuse for high current levels must be larger, and takes longer to melt. Thus, at high current levels, a lead-alloy fuse offers inadequate protection, because electrical catastrophe might happen, before the fuse melts. We need faster-acting, explosive components.

Jan 1, 2009

By Edward J. Walter

Vibration control is affected by many factors which are difficult to isolate and evaluate. Occasionally a circumstance occurs in which one factor appears to predominate and its effects can be evaluated. Changing rock characteristic or lithologic variation is one of these factors or parameters. In a recent seismic monitoring project, lithologic variation in the form of hard lenses occurring suddenly and randomly in the rock to be excavated caused sudden and large increases in vibration level. Data are presented to illustrate these effects, and procedures used to control these effects are described.

Jan 1, 1981

By Michael McDougall

"Suncor Inc. Oilsands Group, Mining Operation in Northern Alberta, Canada, has beenblasting to loosen the oilsands to increase production and decrease maintenance of the hugebucketwheel excavators for over twenty years. In 1991 an area of the mine wasencountered which had a working face in excess of 130 feet. In order to maintain theproduction objective, the blasting department took on the task of providing as much of ablasted face to work with as possible. In doing this Suncor has exceeded several knownrecords in production blasting."

Jan 1, 1993

By Minoru Kawamora, Koichi Kurokawa, Kenji Hashimoto

We developed concentrated remote control blasting system to blasting simultaneously at a large number of sites in a mine of large scale. This system is consisted of three parts, the first part is a control station with high voltage power source units, the second part is a relay terminal with relaying and branching units, and the third part is a blasting machine with charging and discharging units. The control station is connected with the blasting machine by mean of control bus wire. The blasting machine adopts MBS(electromagnetic induction blasting system) for the reason of safety and good handling.

Jan 1, 1990