Search Documents

By D. Kosior

Influence of frothers (a-terpineol and n-octanol) concentration on kinetics of a three phase contact (TPC) formation by a bubble colliding with a hydrophobic surface (Teflon) of different roughness was studied using a high-speed camera (1040 frames per second). It was found that the Teflon surface roughness and the frother concentration strongly affected time of the TPC formation (tTPC) and time of drainage (tD) of the liquid film separating the colliding bubble from the solid surfaces. With increasing Teflon surface roughness, from ca 1 to 80 µm, the time of the TPC formation was shortened by over the order of magnitude, from ca 100 to a few milliseconds only. At low a-terpineol and n-octanol concentrations, thetTPC values were shorter than in distilled water due to lowering the bubble velocity in the frother presence and diminished bouncing of the colliding bubble. However, at high frothers concentrations the tTPC values were prolonged, despite that the bubble velocity was similar. The prolongation of the tTPC at high frother concentrations indicates that air (micro- and/or nano-bubbles) was present at the Teflon surfaces of different roughness. The mechanism of the tTPCprolongation at high frother dosage is described.

Sep 1, 2012

By T. B. M. Himawan

In this study, effect of thiosulphate and oxidation using oxygen were studied in arseno copper ore flotation. Single mineral study of chalcopyrite and tennantite in regard to the aforementioned techniques was also studied. Zeta potential, XPS, contact angle and floatability of single minerals were conducted for each treatment to understand the mechanism. It was revealed that the separation is best conducted in alkaline condition at where there will be interaction between thiosulphate and the mineral surface as well as the formation of hydroxide species in the oxidation using oxygen. From zeta potential of both thiosulphate and oxidation conditioning, it can be found that the reactivity of tennantite is much higher rather than chalcopyrite resulting higher rate of depression on both techniques as shown from contact angle and floatability of each mineral after treatment. XPS spectra confirmed qualitatively and quantitatively the existence of species responsible for the depression of each conditioning techniques. As for the copper ore flotation test, it is the oxidation using oxygen provides best performance after 60 minutes of oxidation. Keywords: tennantite, chalcopyrite, arseno copper ore A, thiosulphate, oxidation using oxygen

Sep 1, 2012

By Paulo Sérgio de Oliveira, Joaquim D. Donda, Andreia C. Rosa

"The search for energy efficient technologies for comminution processes is constant in mineral processing studies, since those processes represent a major percentage of operational costs. In this context the use of stirred mills is increasing, especially for ultrafine grinding. Although many authors claim that these new equipment are more efficient than the conventional ball mills, there were very little chances to prove that in a practical way, since there are few industrial circuits where those technologies perform the same duty. Therefore, the regrinding circuit of Germano second concentrator offers an interesting opportunity: a vertical mill operating in parallel with two ball mills. During almost two years of operation, several sampling campaigns were conducted to evaluate the vertical mill performance and to compare the operational data of the three mills. The industrial data was also compared to jar mill tests results, which are monthly conducted in Samarco labs in order to predict the specific energy consumption required by the ore fed to these circuits. The vertical mill demonstrated the same ability to achieve the product specifications of the ball mills while proved to be able to reduce the medium specific energy consumption in about 40%."

Jan 1, 2014

By Mohsen Hashemzadehfini

Nowadays heap leaching has become established as a mineral processing technology for treatment of some low grade minerals such as copper, gold, and zinc, etc. Heap height, particle size, leach reagent consumption, and metal recovery are four important metallurgical parameters in a hydrometallurgical process like heap leaching. This paper investigated the effects of heap height and particle size on copper recovery as well as acid consumption. Three heap heights of 2, 4 and 6 meters and two particle size fractions of less than 25.4 mm and 50.8 mm were selected as variables in the experiments. The research results showed the inverse relation between heap height and copper recovery as well as acid consumption. Under given conditions, the copper recoveries of minus 25.4 mm ore are 78.63%, 66.27% and 52.88% higher than that of minus 50.8 mm samples for the heap heights of 2, 4, and 6 m, respectively. Both copper recovery and acid consumption increase with decreasing particle size. Keywords: heap leaching, heap height, particle size, acid consumption

Sep 1, 2012

By Megan Becker, Cyril O’Connor, Jenny Wiese, Gaynor Yorath

The effect of particle shape on true flotation has been widely reported. The present paper presents results obtained in investigating the effect of particle shape on the entrainment of particles during the flotation process. Different hydrophilic minerals with particles of varying aspect ratios were used and their shape determined using rheological tests and QEMSCAN. Their entrainment properties showed a close relationship to their shape with the recovery due to entrainment increasing as the aspect ratio of the particles increased. The effect of surface charge, by changing pH, and size of particles showed that the effect of shape was sustained at different pHs and particle sizes. Proposals are made to explain these observations in terms of the known relationships between drag coefficients and terminal velocities and shape. Since it has been previously reported that different milling procedures can affect particle shape, these results indicate that it is possible that such different procedures may result in increased entrainment of hydrophilic minerals.

Jan 1, 2014

By I. Blayda

The purpose of this work is to study and make comparative analysis of germanium extraction and related valuable components of the sublimates from the burning of domestic power coals (product 1) and germanium sulfide materials, which are a waste of lead-zinc production (product 2), by traditional chemical methods (distillation of germanium in the form of tetrachloride from raw and preliminary burning source) and by microbial bioleaching of sulfur-oxidizing bacteria. The dependence of the germanium extraction by chemical methods from phase composition of the initial raw materials was installed. The germanium tetrachloride extraction from products 1 and 2 were 78.50 and 19.52%, respectively. Such difference in indexes on extraction, is caused by germanium confinement as concomitant trace component to the basic phases to carriers. The share of acid-non-soluble compounds (tetragonal modification GeO2 and silikogermanaties) in the product 1 account for 21.5 % of germanium. Ratio between acid-soluble and acid-not -soluble germanium forms are 19.52 and 80.48 %, respectively, in the product 2. Our experiments have shown, that implementation of restorative firing (with addition of 30-40 % carbon at 1150 0?) of sulfide product 2 considerably impacted on the extraction of germanium tetrachloride (91.76 %) in comparison with its low enough extraction at straight distillation of hydrochloric acid (19.52 %). The results are confirmed by a set of physical methods. The results of processing the same so-called hard phase?s material (product 2) with the help of microorganisms are presented. It Has been established, that selected strains of bacteria are capable of extracting from initial raw materials not only macro components (iron, zinc, lead, manganese, aluminum, nickel), but also micro impurity of rare metals (gallium, germanium, zirconium). It is important that these metals were not extracted by traditional chemical methods (with application of aggressive conditions and heats) independently of the phase composition of the source. Almost complete extractions of germanium in solution using sulfur-oxidizing bacteria take place in the first day of the process independently of the phase composition of the source and the type strain. The results have practical significance and can be the basis for developing a unified biotechnological method of technogenic waste processing with a purpose of their sterilization and detoxification with simultaneous obtaining concentrates of valuable metals. Keywords: germanium, extraction, sublimates, bioleaching, sulfur-oxidizing bacteria.

Sep 1, 2012

By Sun Chuanyao, Cao Fei, Sun Desi, Zhou Dezhi

"The research applies the density functional theory and molecule design technology to design and synthesize the novel flotation collectors for copper-sulphur separation. Density functional theory (DFT) was applied to investigate the electronic properties of O-isopropyl-N-benzyl thionocarbamate (IP-BIAN) and O-isopropyl-N-ethyl thionocarbamate (Z-200). The calculation results show that both the energy of highest occupied molecular orbital (EHOMO) and the lowest unoccupied molecular orbital (ELUMO) of IP-BIAN are smaller than that of Z-200, electronegativity of IP-BIAN is higher than that of Z-200. According to the Klopman’s generalized perturbation theory, the collecting power of the two compounds is predicted to be Z-200 > IP-BIAN, the selectivity of IP-BIAN is better than that of Z-200. Then the thionocarbamate molecular is synthesized, and the compounds are characterized by nuclear magnetic resonance (NMR). It turns out that the test result identifies the prediction after the flotation verified test of pure mineral and actual mineral. The results demonstrate that the EHOMO and ELUMO are smaller in the thionocarbamate after a nitrogen atom is bound to benzyl, the thionocarbamate has strong selectivity and low collecting power. The lower the LUMO energy of thionocarbamate is, the stronger the back donation covalent p-bond between collectors and chalcopyrite is, thus improving flotation power for chalcopyrite and selectivity against pyrite. The result proves the feasibility of design and synthesis of the novel thionocarbamate through the frontier orbital properties of the collectors.1. INTRODUCTION Thiocarbamate is a kind of nonionic polar collector and is now widely used as flotation collector for copper-sulphur separation. The flotation power of thiocarbamate to chalcopyrite is stronger than pyrite, so it has high selectivity against pyrite. The frontier orbital theory and density functional theory (DFT) has been widely applied to study the structure-activity relationship of flotation collectors [1-6]. The flotation test results can be interpreted by using the reaction energy criteria and quantum-chemical parameters, such as the energy of the highest occupied molecular orbital (EHOMO) and the energy of the lowest unoccupied molecular orbital (ELUMO) of collector [7-11]. In turn, there are rarely reports about screening the novel flotation collector, by the frontier orbital properties such as HOMO and LUMO of flotation collectors. In this thesis, we apply the density functional theory and molecule design technology to design and synthesize the novel flotation collectors for copper-sulphur separation. Based on the previous findings of the structure-activity relationship of xanthogen formats [12], it has stronger collecting ability to chalcopyrite while the xanthogen formats after a nitrogen atom is bound to benzyl. Thus, in this study, a novel thionocarbamate molecule O-isopropyl-N-benzyl thionocarbamate (IP-BIAN) will be constructed, when the group structure connected with N atom in the known collector O-isopropyl-N-ethyl thionocarbamate (Z-200) is replaced with ethyl by propyl. The collectors (IP-BIAN and Z-200) have been calculated by DFT methods in quantum chemistry. By analyzing the reaction energy criteria and the frontier orbital properties (HOMO and LUMO), this research predicts flotation performance of novel collectors (IP-BIAN), then the synthetic experiments and flotation verified tests are conducted. The research provides a new theory reference for screening out the high-effective flotation collectors of copper-sulphur separation. This technology adoption will contribute to the sustainable development of mineral resources as it shortens the research cycle of new collector molecules and reduces the investment."

Jan 1, 2018

By M. Minagawa, G. Granata, C. Tokoro, T. Kato

"In this work, we studied the mechanochemical activation of chalcopyrite by vertically stirred ball milling (VSBM) to enhance the dissolution of copper. By using x-ray diffraction (XRD) and laser diffraction particle size analysis, we investigated the effect of milling and milling conditions on particle size and phase composition of the chalcopyrite concentrate. To elucidate the efficiency of VSBM towards the mechanochemical activation of chalcopyrite, we also conducted leaching experiments in sulfuric acid-ferric sulfate media. Under all investigated milling conditions, the VSBM determined a dramatic decrease of particle size from over 100 µm of P80% up to about 13 µm. Furthermore, the XRD of the ground chalcopyrite specimens highlighted a partial oxidation of the mineral. In leaching, upon grinding by VSBM, the increase of copper extraction ranged from a minimum of +10% to a maximum of +40%, depending on the grinding conditions. In order to elucidate whether the dissolution enhancement was a consequence of the decreased particle size or of an induced mechanochemical reaction, we performed leaching experiments on activated and non-activated chalcopyrite sample having the same particle size. In addition, we determined the activation energy of leaching before and after vertically stirred ball milling. The leaching results on samples with the same particle size highlighted a greater copper extraction and higher dissolution rates upon mechanochemical activation. Whether performing grinding by VSBM or not, the leaching kinetics was found to be controlled by the chemical reaction on the surface of the chalcopyrite particle. By grinding the chalcopyrite concentrate by VSBM, the activation energy of leaching slightly decreased from 66 to 58 kJ/mol. INTRODUCTION Due to the increasing demand of copper, low grade ores and refractory minerals like chalcopyrite are expected to become the main copper source in the next years (Klauber, 2008). As a low-grade sulfide, chalcopyrite shall be processed hydrometallurgically. However, due to the formation of a protective layer of elemental sulfur during the oxidizing leaching, the dissolution of copper is slow and/or incomplete (De Bernardi and Carlesi, 2013). Therefore, the development of new technologies to enhance the extraction of copper from chalcopyrite is highly required."

Jan 1, 2018

This study examines the surface alteration and flotation behaviour of synthetic moncheite, PtPd(BiTe)2, in the presence of pentlandite. The telluride minerals contribute around 20% ~ 30% and up to 45% of the PGM present in the Platreef ore and are considered to be slow floating as there is evidence of these minerals reporting to the tailings. It was proposed that oxidation products from other minerals and grinding media would affect the mineral surface composition and floatability thereby causing inadvertent depression of moncheite due to precipitating ions. ToF-SIMS analyses (time of flight secondary ion mass spectrometry) was used to characterise the mineral surface as well as the extent of surface alteration. Microflotation was used to deter-mine the hydrophobicity of the synthetic minerals. Conditioning of moncheite in the presence of pentlandite reduced the flotation response of the + 38 -106µm size fraction from > 99% to 56%. This was due to pentlandite dissolution products (iron and nickel hydroxy species) which formed overlayers on the mineral surfaces thereby inhibiting the adsorption of collector. In addition, further grinding of these samples, with and without pentlandite conditioning showed a negative effect on recovery due to the fineness of the particle size distribution and there was no advantage gained from any possible exposure of fresh sites in the sample.

Jan 1, 2014

By Y. M. Zhu, G. C. Gong

"The influences of citric acid (CA) on the flotation behavior of cassiterite using styrene phosphonic acid (SPA) as the collector were studied via single mineral flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations in this paper. The results of single mineral flotation tests revealed under the conditions that pH=4 and the dosage of SPA 100 mg/L, the recovery of cassiterite reached 76.78%. The addition of 20 mg/L AC decreased the recovery by 12.42% at pH=4. Contact angle measurements demonstrated the adsorption of CA prior to SPA made the cassiterite more hydrophilic. The results of zeta potential determinations and solution chemistry calculations indicated the chemisorption of C6H7O7- and C6H6O72- filled parts of the Sn site on cassiterite surface and prevented the SPA from getting adsorbed. The hydrophilic effect of AC was stronger than the hydrophobic effect of SPA and the flotation of cassiterite was crippled. INTRODUCTION Tin is an important metal which is widely used in medical instruments, marine engineering materials, electronic and electrical devices, welding, weapon manufacturing and organotin compounds industries (Angadi et al., 2015). Cassiterite is the only mineral from which the tin can be extracted, thus it is of great importance to efficiently exploit the cassiterite mineral. Flotation is an indispensable method for the recovery of cassiterite (Li et al., 2015). However, cassiterite is usually in association with many other gangue minerals which are of similar floatability, such as quartz, calcite, fluorite, iron oxide, wolframite, scheelite and tourmaline (Sreevinas, 1997). So some modifiers are necessary in the cassiterite flotation process. The amounts of the modifiers used in the flotation must be judicious and the overmuch modifiers may cripple the recovery of cassiterite (Parsonage et al., 1987). Nevertheless, the research about the effects of the modifiers on the flotation behavior of cassiterite has been rarely reported. In this paper, the influences of citric acid (CA) on the flotation of cassiterite using styrene phosphonic acid (SPA) as the collector were investigated by flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations."

Jan 1, 2018

By Achilles Dutra, Everton Santos, José Oliveira

The beneficiation of phosphate ores by froth flotation is the most efficient process used to separate apatite from gangue minerals like calcite, dolomite and quartz. However, the similarity of surface properties between apatite and calcite generally lead to non-selective adsorption of reagents, rendering the selective separation of these minerals a worldwide problem. The phosphate deposit of Itataia, State of Ceará, Brazil, studied in the present work, presents a complex mineralogical composition having uranium associated with the apatite mineral. The main gangue minerals are calcite and quartz. The bulk flotation of apatite and calcite with anionic collectors in an alkaline medium followed by the selective flotation of calcite at pH 5.5 using phosphoric acid as well as citric acid as depressant have been suggested for this ore. This paper presents the results of contact angle measurements obtained using jojoba oil, a natural reagent composed mainly of gadoleic acid (C20:1) and long-chain fatty alcohols (eicosenol and docosenol), as an alternative collector for the selective separation of apatite and calcite minerals. The hydrophobicity studies were carried out using a computer controlled contact angle goniometer. Additionally, the collector adsorption was evaluated via electrophoretic mobility and FTIR measurements. The results indicated that a high selectivity can be obtained by using jojoba oil as collector in a slightly acid pH range, without the use of depressant. The best results were achieved with a jojoba oil concentration of 200 mg.L-1 at pH 6.5, where the apatite was fully hydrophilic and calcite showed a high hydrophobicity (? > 60 º).

Jan 1, 2014

By P. Knüpfer, B. Babel, M. Rudolph, F. Perez Maldonado, U. A. Peuker, L. Ditscherlein

"In heterocoagulation processes for the separation of mineral particles, the most famous being froth flotation, the main characteristic of separation is a differing wettability of the constituents to be separated. This most crucial property in the economically important process of flotation is often only and incompletely, quantitatively described in terms of contact angles against water. A water contact angle larger than 90° is referred to as hydrophobic and hydrophilic vice versa. Looking at Young’s equation shows that it is actually the surface energy of the solid in interaction with the surrounding phases and their surface energies (or surface tensions for liquids) which describes whether there will be hydrophobic/hydrophilic hydration interactions leading to attraction or repulsion. This, we have previously published for various more or less hydrophobic minerals in correlation to their flotation response, i.e. flotability (c.f. Rudolph & Hartmann, Coll.Surf.A 513, 380-388). In the same paper we also discussed the heterogeneity of wettabilities as assessed with the novel method of inverse gas chromatography. Furthermore we have also reported on hydrophobic force distributions as assessed with atomic force microscopy which are as well due to wettability heterogeneities (c.f. Fritzsche et al., Coll.Surf.A 459, 166-171).In this paper we present wettability distributions of different substrates and particles with various surface roughnesses/shapes and degrees of hydrophobization as assessed with iGC, AFM and dynamic sessile drop analyses. We are putting the results in context in unifying models and present methodologies helpful to make use of the fundamental information and their impact on the actual industrial separation process in fundamental process models. Besides froth flotation we also emphasize the impact on selective hydrophobic flocculation process."

Jan 1, 2018

By P. K. N. Raghavan

Bauxite is the principal source for the production of aluminum metal which has gained tremendous importance over the years due to its versatility as a metal capable of substituting almost all of the non-ferrous metals, non metals like wood, plastics, fibre glass, etc. and even steel in many applications. 90% of the high purity alumina needed for the production of this wonder metal in the world comes from bauxite. Even though alternate methods have been developed to produce alumina from non bauxite sources, owing to the high capital and operating costs involved, Bayer process still retains the superiority among all the methods by virtue of its simplicity and favourable economics. Bauxite continues to be the perfect ore for alumina production and its remarkable utilization makes it the most important non-ferrous ore. Most of the Alumina Refineries in the world process different types of bauxite and that too from varied sources. The technology employed in the Alumina Refineries depends on the Bauxite processed, with an ultimate view to produce alumina of required quality in the most efficient manner. Bureau of Indian Standards (BIS) and Indian Bureau of Mines (IBM) had from time to time put forward bauxite specifications for metallurgical and other applications. However, these are found no fully based on alumina technology, present developments and availability of different types of bauxite in the country. The aim of this paper is to provide scheme of metallurgical grading of Indian Bauxite based on the background of alumina processing technologies and availability of various types of bauxite in the country. Efforts are made here to evaluate beneficiation techniques for central Indian Bauxite from the point of view of alumina production. Keywords: bauxite beneficiation, digestion, alumina, gibbsite, bohemite, diaspore

Sep 1, 2012

By B. Aydin, G. Erturk, G. Bulut

Coal is a complex material because of its structure consisting of carbon constituents and mineral matter. Flotation is readily carried out due to hydrophobic characteristic of coal. Therefore coal flotation is the most commonly used technique for fine coal beneficiation in order to acquire clean coal separating ash forming mineral matter from carbonaceous matter. In the coal flotation, floatability of coal both depends on characteristic of coal and used flotation reagent. Frothers as a flotation reagent are used to facilitate air dispersion into fine bubbles by prevention of bubble coalescence in the pulp phase, and stabilization of flotation froths. In this study, the effects of frother types and concentrations at different pH and particle size on the coal flotation were investigated. The representative sample was taken from Zonguldak, Turkey. It contains 9.1% ash and 7313 (kcal/kg) calorific value. Pine oil, Dowfroth 250, MIBC and Isooctanol were tested as frother types. It is determined that 1.92 ppm frother concentration is sufficient to float coal, except pine oil. In mixed frother tests, it is seen that Dowfroth 250 is more effective than others. No significant difference in coal recovery was observed for flotation tests at the different pH values. The best results are obtained in size of coal (-0.1 mm) with all frothers.

Jan 1, 2014

By H. Lieberwirth, M. Hesse

"Selective comminution (SC) is beneficial for the treatment of primary raw materials, especially if it is utilized in the pre-concentration process. Pre-concentration processes are applied in mineral processing to relieve subsequent processes and to achieve a higher efficiency. SC is also a promising method for the treatment of low-grade ores and waste dumps. With SC, various components can be separated such as valuable minerals from waste, ore from wall rock and different ore varieties within a deposit. SC is a property of a comminution system and leads either to a preferred crack propagation in one component (called preferential breakage) or to a preferred crack propagation along the grain boundaries (called interfacial breakage). SC results from different comminution behavior of various components in the feed material. For mechanical comminution, the preferential breakage seems to be the most important case of SC. Hereby SC generates only the difference in the particle size which can finally be used as a sorting parameter. A sorting process which uses SC depends on three parts: the feed material, the comminution machine and the separation machine. The feed material defines the potential for SC. Differences in properties like strength, toughness and density which are related to comminution are often used. The comminution machine has to exploit this potential. The extent of the exploitation can be influenced by the machine design, material and operational parameters. After SC, the various components are still combined in the product. So ultimately, a separation machine is needed. At preferential breakage, a simple screening machine can be used. The basics about SC will be presented at first. This contains relationships between material properties, the kind of loading in the comminution machine and the SC effect. These basics can be used for example to exploit a potential to SC for a pre-concentration step or to avoid the SC for a higher efficiency of subsequent processes. Based on recent investigations with impact load, the influence of the important parameters compressive strength, density, particle size and impact velocity to the SC will be shown, using examples of lead-zinc ore comminution and fluorspar processing."

Jan 1, 2018

By Sami Makni, Ahmed Bouajila

"To remain competitive in an open market, mining companies are more and more requested to optimise their complex and highly multivariate processes. The increasing amount of process data, brought about by intensive use of instrumentation and the progress in computer data acquisition, enhances the need for more and more powerful and robust tools for the analysis and modelling of the process data. Now, with the emergence of multivariate data analysis (MDA) techniques, on-line clustering of mineral process behaviour is possible and could help in the extraction of valuable process operation indicators. MDA can be used in different mineral processes such as flotation, grinding, smelting etc.In this paper, we focus on grinding process considered as the most costly and power consuming node of the mineral processing scheme. Different objective-oriented levels of data clustering will be addressed.First, the evaluation of grinding operation taking into account data and constraints from all processes before (e.g. blasting, crushing) and after (e.g. flotation, leaching, etc.) the grinding node. The second level deals with process diagnosis by differentiating operation level and identifying behaviour drifts. Control and optimisation are two other levels concerned here with the selection of optimum trajectories in the drift correct.Industrial plant data are processed in order to illustrate the feasibility and the potentiality of MDA applications in addressing the clustering and interpretation of grinding mill behaviour."

Jan 1, 2003

By T. Sreenivas

This paper describes results of laboratory studies on recovery of dissolved uranium values from alkaline leach slurries of a medium-grade uranium ore from Gogi (Karnataka, India) using the resin-in-pulp (RIP) process. Besides anionic carbonate complex of uranium, the other major ionic constituents of the leach solution are CO32-, HCO3-, SO42- and MoO42-. The total dissolved solutes (TDS) are about 45 g/L. Various commercially available strong bases anionic resin-in-pulp (RIP) grade resins ? both macroporous and gel type, were studied with respect to their loading capacity. Parametric variation studies were then carried out with the short-listed resins. Results of the semi-continuous counter-current extraction and elution tests indicated extraction efficiency of about 98% and practically complete elution of the loaded uranium values with NaCl eluant using a gel type polystyrene based resin grafted with quaternary ammonium ion. Keywords: uranium, hydrometallurgy, ion exchange, resin-in-pulp

Sep 1, 2012

By M. Gonzalez Fernandez

"If the final goal of metallurgy is the extraction of metals from a given ore, everyone knows that this achievement relies on many separation steps involving much more than a biphasic material made of metal and gangue. Nevertheless, still today, most of the design and follow-up of industrial processes only consider metal grades; in best case metal grades per size class. Working with such heterogeneous material, made of several minerals, with different grain size and texture, implies to consider finer ore models to be able to predict the behavior of material and the subsequent operation performances. Analytical tools are now available to provide such relevant and accurate data which are applied in geometallurgy. To achieve a true geometallurgical approach for process design, but also for optimization, accurate process simulation absolutely needs to combine these fine ore models with the corresponding unit operation models. Based on generic, but configurable, criteria of description and a hierarchical approach, the material modelling tool embedded in the USIM PAC process simulator provides the necessary flexibility to describe any type of ore with almost no limit in the level of details and associated physical properties that can be met in the mining industry. The simulation engine and the mathematical models of unit operations are designed to manage such a diversity of material modelling. The paper present various ore models and some of their applications in flowsheet simulation. It proves the interest of this detailed and advanced approach to accurately predict plant performances. INTRODUCTION Process simulation used for process design and optimization requires accurate unit operation modeling. During the last decades, main efforts of the different teams developing software simulators have been dedicated to those models for comminution and physical separations such as flotation or gravity concentration (Kojovic et al., 2012, Soni and Yoon, 2014). In most case, the ore is modelled with a size distribution and metal or mineral grades. A water phase is considered for wet processes. The association of unit operations and such material models generally allows, after some parameters adjustment, to achieve good agreement between experimental and simulated data. The use of the obtained simulator to test alternative configuration of circuits or settings of equipment devices can be accurate enough as far as the ore processed is close to the ore used for simulator adjustment. However, when the ore gets very different grades, coming from different mineral proportions or grain sizes, the simulation results can be of poor accuracy. Because any physical separations such as gravity, magnetic or flotation, do not sort metal and gangue but particles, made of minerals, containing metals, the only way to be accurate enough for allowing extrapolations, is to model particles. The phase model tools embedded in the USIM PAC process simulator gives this possibility. However, as such level of details are not always available for analyses, the tool has been designed with a high level of flexibility, to adapt the model to the available data. In this paper, the principles of this conceptual modelling tool are presented, and some application cases illustrate the material model flexibility and its interest."

Jan 1, 2018

By H. Matsuoka, M. Kawata, K. Haga, K. Mitsuhashi, C. Tokoro, A. Shibayama, R. Kawarabuki

"The mineral surface characteristic is important for the flotation because it affects the flotation behavior of the mineral. Conventionally, in the flotation process for Cu sulphide ores, the degree of ore floatabilities varies depending on the mineral phase such as chalcopyrite, bornite, or chalcocite. Therefore, mineral surfaces are treated with activators and depressants to control the floatability of target minerals and obtain high recovery performance. There are lots of flotation reagents which have many effects on ores depending on ore characteristics and conditioning methods. For example, sodium hydrosulphide (NaHS) as activator is known to have the effect of resulfurizing and activating oxidized surface of chalcocite and bornite. On the other hand, NaHS is reported to depress chalcopyrite floatability. In this study, the evaluation of mineral surfaces was conducted to predict flotation behavior. Activation of Cu minerals (chalcocite, bornite, and chalcopyrite) by NaHS was experimented. The three Cu minerals were treated in two steps. Firstly, they were oxidized in the drying oven. Secondly, they were treated with NaHS solution. After each treatment step, each mineral was measured by contact angle apparatus then analyzed by X-ray photoelectron spectroscopy (XPS). The results of surface characteristics after oxidation and NaHS treatment were utilized to accomplish the study’s objective. INTRODUCTIONCopper sulfide minerals such as chalcocite (Cu2S), bornite (Cu5FeS4), chalcopyrite (CuFeS2) are well-known abundant copper-containing minerals. Generally, these minerals are recovered and concentrated via collector flotation. In flotation, the wettability of the mineral surface is an important factor in its recovery. When the surface is hydrophobic, the mineral has high floatability and when the surface is hydrophilic, it has low floatability. Usually, Cu sulfide minerals have high floatability. However when their surfaces are oxidized, their floatability becomes lower in flotation. In this case of surface oxidation occurrence, activators are added before flotation to modify the surface property of the Cu sulfide minerals so that they can be floated at a certain flotation condition. Sodium hydrosulfide, NaHS, is known as one of the activators. Zhao et al. (2018) reported that NaHS is often used as sulfurizer for oxidized sulfide minerals (Becker et al., 2014, Clark et al., 2000, Newell et al., 2006, 2007, Newell and Bradshaw, 2007). Although the floatability of Cu sulfide minerals was raised by adding NaHS generally, the results of this flotation study showed that the flotation behaviors of mixed chalcocite, bornite, and chalcopyrite were different. Therefore, it was considered that NaHS works differently for each mineral."

Jan 1, 2018

By G. A. Wierink

This paper discusses a new method to increase flotation recovery. As known from literature, fine and coarse particles have different flotation rate constants, hydrodynamic behaviour and require different reagent regimes. The device discussed allows separate processing of finer and coarser slurry by extraction of a third stream, carrying finer slurry, from the flotation cell. By separate treatment of fine and coarse slurry operational conditions and so flotation recovery for both may be optimized more efficiently. Extraction and classification of the third stream is accomplished by low speed centrifugation and Taylor-Couette flow separation. This Dual Outlet Device (DOD) can be installed in a traditional flotation cell without need for equipment replacement. In order to asses different design options for the DOD a transparent laboratory scale model was built. For this scale model Computational Fluid Dynamics (CFD) simulations using the RANS k-e and LES turbulence models were performed. Essential insight in the dominant flow systems relevant to optimal operation of the DOD was obtained from the CFD simulations and flow visualization tests with the laboratory scale model. Based on these findings a number of configurations were investigated at pilot plant scale in a 5 m3 Outokumpu flotation cell. The results of the pilot plant study show that utilization of the DOD provides a method for in-cell control over particle size distribution in the slurry. Use of the DOD in a flotation cell may enhance flotation recovery and decrease flotation reagent consumption significantly, against marginal investment and operation costs.

Jan 1, 2014