Search Documents

By Wolfgang Öfner

Many technical processes also yield dusty residues which usually contain appreciable amounts of valuable matter. Often they also accumulate substances detrimental to the process. Dumping them entirely in landfills wastes raw material and causes high disposal costs, but recycling them without prior treatment is often not feasible. Physical separation processes are preferable because of their rather low energy demand. In order to develop such treatment systematically, the residues must be characterized properly. The technique for such a characterization is taken from mineral processing: perfect fractionation according to continuous properties of the particles supplemented with chemical analysis are used for plotting the Henry-Reinhardt chart. This represents the benchmark for assessing actual separation processes and tests. Their results are compared in terms of ?selectivity? and plotted in the kappa chart. In this paper, Henry-Reinhardt chart and kappa chart are applied to several different types of residues from iron and steel production and show their potential for being upgraded before reutilization in the production process. This approach is suitable for virtually all dusty residues from other industrial processes as well. Keywords: residue, dust,iron and steel, process development, Henry-Reinhardt chart, kappa chart

Sep 1, 2012

By Swati Mohanty

Spiral concentrator, which works on the principle of gravity separation, is widely used in the mineral industries for separation of solid particles based on the size and density. In the present study, CFD simulation of the flow profile on a laboratory scale spiral concentrator of height 2.29 m, pitch 0.435 m and width 0.17m was carried out. A single computational domain covering the entire spiral was considered. Volume-of-Fluid algorithm was used to track the interface and predict the flow profile. In the present study the Donor-Acceptor method was used for the calculation of volume fraction in the cell. Simulation results show that the velocity increases as the water flows down due to the convective force and gravitational force, but the viscous force acting in the opposite direction retards the flow. Thus the maximum velocity is attained at turn three at which the viscous force overpowers the other forces and further down the velocity decreases. Measured water depths along the radius of the spiral at various heights were compared with simulated depths, which were in good agreement. The simulated liquid phase velocity profile was used to carry out preliminary studies on the flow profile of solid particles of size 500 micron and densities 2600kg/m3 and 5100kg/m3, based on the Lagrangian model taking into consideration fluid-particle interaction.

Sep 1, 2012

By Rintaro Hayashi

The enrichment of useful components from ores and/or wastes has become important with increasing recent worldwide resources demand and the amount of wastes generated from the urban mines, in order to establish real ?sound resource-cycle society? including the activity of resource exploitation. The first stage of the treatment in the process must be comminution and it is important to make good liberation among compositional phases in the targeted resources. Electrical disintegration (ED) is well known to make a selective breakage at phase boundary. However, the detailed mechanism of the phenomena is not clarified yet, in especial, on the influence of electrical properties of compositional materials on the liberation. This paper made a comparison between the liberation degrees of ED products and the results of electromagnetic field analysis using finite element method (FEM). In the experiments, we used several synthetic cement paste based samples in which mineral particles were dispersed to apply the ED, and in the electromagnetic field analysis, we calculated the charge density accumulated and the Maxwell stress at phase boundary. It was found, for highly insulating mineral samples, that higher breakdown voltage was necessary because electric charge was not easily accumulated at phase boundary but that higher liberation degree was obtained after the breakdown (ED). It was also found the tendency that higher liberation was observed for the samples which had higher maximum Maxwell stress calculated by the electromagnetic field analysis. From the results, the electrical charge and Maxwell stress induced at phase boundary could be driving forces of selective breakage. In addition, we also applied the ED to the printed circuit boards (PCBs) in order to concentrate miner rare metals, which were essential for producing electronic devices. It could be demonstrated that the devices installed on the PCB were easily detached from the board and that most of metal elements in the devices was exposed and liberated from the insulating plastic covers, which were broken in the ED, then, it is considered that the subsequent solid phase separation could be effective for concentrating such metal elements. Keywords: liberation, electromagnetic field analysis, printed circuit board, miner rare metal

Sep 1, 2012

By Kazutoshi Haga, Ryo Kawarabuki, Atsushi Shibayama, Masato Kosugi, Masanobu Kawata, Refilwe S. Magwaneng, Kohei Mitsuhashi, Altansukh Batnasan

"The recovery of copper and iron from carbonaceous sulfide ore is of economic and environmental interest despite its processing difficulty. Hydrometallurgical methods can be used to concentrate sulfide metals of these hard-to treat ores in a simple and eco-friendly manner. In this study, high pressure acid leaching process was comprehensively studied to dissolve metals from an ore with organic carbon and carbonaceous gangue material using autoclave equipment. The sample used for the experiment was reduced to an average particle size of 75 µm after undergoing flotation to reduce carbonaceous gangue minerals. A comparative study on two leaching reagents of sulfuric acid and iron sulfate and their dosage was used to observe dissolution of copper and iron. Other parameters of temperature (90-170 0C), solid-liquid ratio (1:10, 1:5, 1:3 and 1:1) were investigated through kinetic studies to access the influence of organic carbon and carbonaceous material on recovery of copper and iron. Materials balancing analysis was used to evaluate the efficiency of metal dissolution. The effects of parameters on leaching rate and concentration was demonstrated. Results obtained from the experiment indicated low concentrations of copper and iron in pregnant leached solutions, which was attributed to acid consumption by organic carbon and carbonaceous material in feed. However, the high efficiency rates of 92.4% and 86.3 % for copper and iron respectively in sulfuric acid can be concluded that leaching of concentrates of carbonaceous ore is possible provided system control on type of acid, pH and temperature. The purpose of this research is important in understanding mechanism involved in dissolution of copper and iron in concentrates of carbonaceous ore and marks an improvement in leaching of highly contaminated ores."

Jan 1, 2018

By G. Atesok

Turkey?s EU affairs started in 1963 with the Ankara Treaty. On 31 December 1995 the Customs Union between Turkey and the European Union came into effect. In order to achieve the Copenhagen Criteria?s, Turkey, made laws parallel to the Framework Programs. On 3 October 2005, with the confirmation of ?Membership Framework Document? the negotiation process of Turkey has started. Coal had important role in the industrialization of EU and it is directly related to Energy and Environmental subjects. In this point many restriction became with the some protocols, in last decades. European Union composed Energy and Coal Policy, therefore engaged to reduce the emissions, and made new regulations. This regulations concern Turkey?s energy future, since large; but low quality of lignite reserves of Turkey, it is expected to have some difficulties with Union?s Environmental Legislation during Turkey?s congruity process. With the last natural gas import agreements of Turkey, the production and consumption of coal sunk in last seven years. However, considering environmental sustainability, the role of coal in energy production will rise up in the coming future. In this paper, in terms of Turkey Energy Sector, production and consumption problems of coal discussed and evaluated considering EU?s coal, energy and environmental rudiments.

Jan 1, 2014

By Danfeng Xu

The majority of the world?s nickel (Ni) resources occur as laterite ores, which are exceptionally complex, lower grade (<1.5% Ni) and expensive to treat using conventional smelting and high temperature/pressure autoclave methods. Heap leaching is a promising, less costly, alternative technology for processing low grade nickel laterite ores. However, significant technical challenges remain with Nickel laterite heap leaching, preventing its general adoption. This paper presents some highlights of laboratory column leaching studies undertaken to characterise, evaluate and optimise sulphuric acid leaching behaviour of Nickel laterite agglomerates. They provide basic but valuable information regarding Nickel laterite agglomerate structure stability and leaching performance under industrially-relevant, continuous acid irrigation conditions. In particular, Nickel and other key metals? (e.g. Co, Fe, Al and Mn) extraction rates, free acid concentration, bed slump and structural changes were determined at a given acid percolation rate as a function of time. Potential implications of the findings, for devising strategies for improved Nickel laterite plant heap leach operations are discussed. Keywords: nickel laterite, column leaching, agglomerates, leaching kinetics, acid consumption

Sep 1, 2012

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered feed samples in a larger KC as op-posed to the commonly adopted GRG test has been discussed.

Jan 1, 2014

By H. Allenius

Today, most requests for quotations force all bidders to follow the bid document to the letter. The choice is then made based on price since it is the only difference in technically identical offers. However, clients allow and even encourage suppliers to come up with alternatives. Overall economy again, is much more than low investment costs. Operation costs may affect the economy of a project far more than a million saved in investment. There is almost always the choice: Should we go for the cheapest solution or should we go for the most economical solution? We strongly recommend the study of the long-term effects on investments as they often surpass any apparent savings in capital expenditure. With high operating costs, time is never on our side. Almost all relevant inputs and outputs in a concentrator have a value that can be expressed in a suitable currency. Unit prices may differ substantially from one operation to the other, but everything has a price tag and globalization has made it possible to move both goods and services to almost any place in the world. Even a rather simple exercise can give a good indication on which process improvements are worth pursuing when investing in new systems or equipment. The ones that do not qualify, as money earners, will naturally appear as clearly. No ?rocket science? is required, just process knowledge, practical experience, an open mind and some common sense and the reward may be the difference of having a good or an excellent project. The model we have developed can be made as detailed as required, but we do not recommend too much detail, as it sometimes tends to distract work and obscure the important issues. Two different process solutions compared in a simplified example illustrate the importance of evaluating a project based on its long-term effects rather than focusing on the investment costs only.

Jan 1, 2014

By Wei Qu, Yongsheng Song, Xingyu Liu, Wenjuan Li, Shuang Liu, Guiying Zhou, Bowei Chen

The Pb,Sb,Zn multi-metal sulphide ore is processed in sequence of beneficiation of jamesonite, sphalerite . Due to relative large amount of collector (xanthate), activator (CuSO4) and regulator (lime) during different flotation stage, the flotation wastewater from sphalerite beneficiation stage can’t be directly recycled to the first lead flotation stage. In this paper, the flotation wastewater from sphalerite beneficiation stage was treated by Ozone and BAC technology, results showed that when the influent concentation of COD and copper ion were 850 mg/L, 10.48mg/L respectively, the Ozone and BAC technology could effectively treat such type of water. In the treated wastewater, the COD is 60mg/L, copper ion concentration is 0.023mg/L, pH is 7.0, which satisfy the need of Pb,Sb-Zn preferential floatation separation process. After recycle of the treated wastewater to Pb,Sb floatation circuit, qualified Pb,Sb concentrate and Zn concentrate were obtained.

Jan 1, 2014

By G. C. Li

Gold extraction using iodide leaching from refractory carbonaceous gold ores was studied. Thermodynamic analysis of iodide leaching chemistry had been carried out. Eh-pH diagram of Au-I2-I--H2O leaching system showed that the coordinating active forms from iodides were I3- and I-, while the major coordinate compound formed during iodide leaching was AuI-. For leaching parameters optimization, technological parameters such as I2 concentration, I2 :I- ratio, oxidation assisting agents, liquid/solid ratio, and leaching duration were studied. The leaching results showed that the average Au leaching rate reached 91% and 92% for oxidized ore and roasted primary ore respectively. Leaching process proceeded in weekly acidic or neutral slurry at ambient temperature; the leaching duration was 4 hours. After that gold was extracted from the pregnant liquor by activated carbon adsorption ? desorption ? electrowinning process. Gold recovery was over 93% in the adsorption process, while the gold recovery in electrowinning process was about 95%, provided that the initial gold concentration is 40mg/L or larger. For iodine regeneration it is enough to add hydrogen peroxide in excess into the filtrate after gold electrowinning, all the iodides existing in the solution in any forms would be precipitated in the form of elemental iodine.

Jan 1, 2014

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By D. W. Lui

Tangdan copper oxide deposit, the largest independent copper oxide deposit in China so far, is located in the northeast of Yunnan province, southwest of China. The ore from this deposit is characterized by: low grade, high oxidation ratio, and fine-grained disseminated, resulting in poor flotation recovery. The analysis of plant flotation data reveals that the loss of copper minerals into tailings is mainly with coarse size fraction due to insufficient liberation and fine size fractions, especially minus 10 microns fraction, which proved to be very difficult-to-float with conventional flotation. In order to improve the performances of plant flotation of this ore, laboratory flotation tests were conducted with the pure malachite, which was the principle copper oxide mineral in Tangdan copper ore deposit. The results obtained suggested that a finer grinding (up to -325 mesh or even -400 mesh) be needed to decrease the loss with coarse size fraction, and vacuum flotation is a promising way for the recovery of the fine malachite effectively.

Jan 1, 2014

By R. M. Zhao

The process conditions and mineral characters of cleaning separation stage in magnetite concentration plant are studied in the paper, and the affecting factors and the methods to increase the concentrate grade are analysed and given. The BKJ cleaning special drum magnetic separator is developed specially for the cleaning stage according to process conditions and mineral character. The separation mechanism, structure characters, separation process and excellent adaptability of BKJ special magnetic separator are described. The results in Zhangjiawa Concentration Plant show that the BKJ special drum magnetite separators play an important role in increasing the concentrate grade and improving the economic benefit.

Jan 1, 2014

By Shenxu Bao, Ying Bian, Xiang Liu, Liuyi Ren, Yimin Zhang, Chun Liu

Efficient enrichment of high-carbon low-grade mica stone coal containing vanadium is a key problem in the mineral processing field, and the mature beneficiation process is yet to be developed and applied. In this paper, a special mineral mica type of stone coal containing vanadium from Tongshan, Hubei Province, China was selected as the research object. Chemical analysis results show that this mineral contains V2O5 0.71%, SiO2 49.28%, C 13.44%, and CaO 6.26%. Scanning electron microscope (SEM) shows that vanadium generally exists in all kinds of mica minerals in 20 µm to 50 µm fractions. Mica stone coal containing vanadium must be ground to a particular fineness (approximately 45 µm). To reduce acid consumption during vanadium extraction from stone coal through acid leaching, a pretreatment process was proposed to enrich micas by using shaking table and flotation methods. A new combined technology process was implemented, resulting in a 0.96% improvement in the vanadium grade of raw materials in the succeeding process. Vanadium losses were controlled to 4.57% through the pre-concentration process, which reduced the burden of the subsequent procedure. The content of high acid consuming minerals was also diminished, such that approximately 6612 CNY was saved from producing 1 t V2O5. Therefore, stone coal containing vanadium should be pre-concentrated by using an appropriate combined process to reduce costs.

Jan 1, 2014

By B. Q. Xiao

In surfactant flooding, surfactants added are often a mixture of the same type of molecules with different lengths of carbon chains. The relationship between a single, pure surfactant solution and crude oil is seldom studied. Additionally, up to now, alkylbenzene sulfonates are applied widely in surfactant flooding, such as Daqing oilfield, China. A factory producing alkylbenzene sulfonates will enlarge its yield to 20 000 tons per year over there. For the purposes of widening the alkylben-zene sulfonates? application, 16 kinds of pure alkylbenzene sulfonates were synthesized through Friedel-Crafts acylation and Wolff-Kishner reduction reactions, and the compounds? molecular structures were confirmed by 1HNMR and 13CNMR spectra. The factors affecting interfacial tension (IFT), such as, surfactant type, oil composition, electrolyte concentration, and alkali concentration were considered. The synthesized pure surfactants? critical micelle concentration (CMC) and optimal salinity were measured through interfacial tension technique. According to lab experiments results, heavy alkylbenzene sulfonate (2SY) was synthesized in magnifying scale in Jinzhou Wash Chemical Plant and the coretests were conducted using it. The results showed that the homemade heavy alkylbenzene sulfonate (2SY) flooding can improve oil displacement efficiency 20% more than water flooding at surfactant?s concentration from 0.05%(wt) to 0.2 %(wt).

Jan 1, 2014

By T. Fujita

The incinerated bottom ash includes titanium oxides and a small amount of chromium oxides. Initially, 89 % of chromium was removed from ash at magnetic flux density at several stages of wet magnetic separation from 0.05 T to 6 T. The bottom ash from an industrial waste incineration process includes about 10 % of TiO2. The minerals that contain titanium are rutile and perovskite. These minerals are paramagnetic and show low magnetic susceptibility, therefore, the high magnetic field strength, created by a superconducting magnet, is necessary to capture these minerals. At the first stage of separation, a magnetic field strength of 6T was applied in order to attract the particles that contain iron oxides to the higher magnetic field region. At the second stage of separation, the magnetic capture rate of weekly magnetic particles decreased with increasing the magnetic susceptibility of the aqueous solution (i.e. the medium for dispersing the particles) in order to separate the highly magnetic materials. The para-magnetic salt such as ferric chloride was dissolved in the water to increase the magnetic susceptibility of the medium. After a two-step wet HGMS with superconducting magnet, the grade of TiO2was increased from 10 % to 28 % with a recovery of 64 %.

Jan 1, 2014

By Antony Amberg, Gonzalo Saldías, Romke Kuyvenhoven, Catherine Souza, Heriban Soto, Francisco Soto

"Vizcachitas is an advanced stage copper–molybdenum porphyry deposit, fully owned by Los Andes Copper and located in Central Chile. The property contains an indicated resource of 1,038 million tonnes grading 0.37% Cu and 0.012% Mo, and an inferred resource of 318 million tonnes grading 0.345% Cu and 0.013% Mo (Coffey & Alquimia, 2014). The deposit occurs in the same geological belt as several other giant copper-molybdenum porphyry deposits including Río Blanco-Los Bronces, Los Pelambres-Pachon and El Teniente. In 2018, the original Preliminary Economic Assessment (PEA) study from 2014 was updated; this paper presents the geometallurgical testwork that was performed to support that update. The testwork focused on the metallurgical characterization of 40 DDH samples and the development of a more profound orebody knowledge by relating geological features with metallurgical performance. The scope of work included complete chemical and mineralogical QemSCAN characterization; SAG, ball mill and abrasion testing; complete rougher and cleaner kinetics including locked-cycle-test; environmental ABA and settling tests on rougher tailings. The results show that the ore can be classified as medium-hard, with a hardness that is slightly below the average for large Cu/Mo deposits in the region. A good correlation was found between lithology and breakage characteristics, implying that the specific energy consumption (kWh/t) is well correlated to rock type. The results of the flotation tests were very encouraging and did not show significant variability. An overall Cu recovery of 91% can be expected for the flotation circuit. The use of a relatively coarse primary grind size gave good final recovery and grade for both Cu and Mo, and deserves further attention in future work, as this impacts positively both energy consumption and water recovery.INTRODUCTION Los Andes Copper Ltd. is a Canadian exploration and development company focused on the acquisition, exploration and development of advanced stage copper deposits in Latin America. The company owns 100% of the Vizcachitas project in Chile, the largest copper deposit in the Americas not controlled by the majors. Vizcachitas is a copper-molybdenum porphyry deposit, located 120 km north of Santiago, in an area of very good infrastructure."

Jan 1, 2018

As a kind of collector, Xanthates are generally used to make sulfide minerals hydrophobic in flotation process. Xanthate adsorption on a galena surface has been widely studied experimentally. In this paper, DFT methods were employed to investigate the local adsorption interactions about the collectors,such as ethyl xanthate (CH3CH2OCS2?, EO) and ethyl trithiocarbonate (CH3CH2SCS2?, ES), absorbing on two different PbS clusters. From the results, it can be easily found that, on the edge or at the apex, both collectors, with two S atoms bidentate coordinating on the clusters, have surprising interaction energies, while on the surface, its interaction is relatively weak in the form of monodentate ligand. NBO analysis results reveal that there is at least a covalence bond with sulfur atom about 10% and lead atom about 90% when the absorbed lead is on the lattice edge or at apex, but, if the absorbed lead is on the lattice surface, no covalence band would be found. Meanwhile, the S-Pb bond, formed by the absorbed Xanthate and galena lattice, seems to have much more covalence characteristic than that formed in the PbS lattice inner. Furthermore, those data also imply that the difference of the collecting effect between the EO and the ES may be not notable, because of the similar distance and the interaction energy for the same interaction mode.

Jan 1, 2014

By Xiqing Wu, Tao Yue

"Magnetic seeding co-agglomeration, i.e. adding magnetic seeds, organic depressant (such as the starch), and pre-magnetization for co-agglomeration, was applied in the reverse flotation for hematite ore slimes. Samples of the hematite ore slimes and the pure hematite fines were investigated by the co-agglomeration, respectively. Flotation tests suggest that the depressing effect of starch in the flotation was further enhanced with the addition of magnetic seeds and the pre-magnetization. Following the laser size analysis and flotation tests, TOC adsorption analysis, VSM, surface charge measurement, AFM, FTIR study, and SEM imaging have been utilized to understand the depressing mechanism. Based on the results it was demonstrated that with the addition of magnetic seeds and the low field pre-magnetization, the adsorption of starch onto hematite minerals was strengthened through the magnetic seeding co-agglomeration. The co-agglomeration improved the flotation performance by introducing the magnetic interactions and acting the bridging adsorption of starch between fine hematite and magnetic seeds in a suspension, and then resulting in an intensified coverage of the starch onto hematite particles and positive action in the coagglomeration under the pre-magnetization.INTRODUCTIONFlotation is undoubtedly the most important and versatile mineral processing technique, and both its use and application are continually being expanded to treat greater tonnages and to cover new area. However, its influence was limited to a relatively narrow particle size range of 5–300 µm (Wills and Napier-Munn, 2006). The main reason behind this limitation lies in that fine particles have high specific surface area, so need relatively high dosage of reagents (collectors or depressants), and exhibit poor flotation performance while intermediate or properly-sized particles produce high flotation kinetics and need low consumption of reagents. In order to increase the recovery of fine particles, quite a few of flotation techniques have been investigated. Most of them are based on particle aggregation, namely, by enlarging the apparent particle size, such as carrier flotation (Valderrama and Rubio, 1998; Zhu et al., 2009), shear flocculation (Duzyola and Ozkan, 2010; Yin et al., 2011), selective polymer flocculation (Rubio et al., 2007; Song et al., 2012; Ng et al., 2015), oil agglomeration (Laskowski and Lopez- Vladivieso, 2004; Forbes, 2011), temperature responsive polymer flocculation flotation (Forbes et al, 2011), and etc. However, these techniques above-mentioned are mainly studied for the direct flotation of fine minerals, and most of these techniques have not found applications for iron ore slimes especially recovered by the reverse cationic or anionic flotation."

Jan 1, 2018