Search Documents

By S. M. Bradshaw, V. Rocher, L Kabondo, B. Combrink, C. A. Snyders

Media losses are a significant contributor to the operational cost in a dense media separation (DMS) circuit. Of these losses, up to 80 wt% can occur on the drain and rinse vibrating screens. Although these screens are an integral part of any DMS circuit, surprisingly little work can be found in open literature regarding the effect of aperture configuration on the drain rates (draining water and medium). To establish the effect of slot aperture size, experiments were conducted on a 0.6 x 1.2 m vibrating screen with polyurethane (PU) panels at slurry densities between 1.6 – 2.8 kg/L, and volumetric flow rates of 19 – 25 m3/h for both ferrosilicon and magnetite. Results showed that an increase in the volumetric flow rate led to an increase in drainage rate, moisture content and medium carryover. Once an optimum volumetric flow rate was exceeded, a further increase in flow rate resulted in a decrease in drainage rate with a sharp increase in moisture and medium bypass to the oversize stream. An increase in ferrosilicon slurry density led to a decrease in drainage rate with an increase in moisture and medium bypass with each of these rates increasing as the slurry density increased. For magnetite, a gradual decrease in drainage rate was observed with increase in slurry density and volumetric flowrate beyond the screen optimum point. It was found that an increase in aperture size from 0.63 x 8.8 mm to 0.8 x 8.8 mm to 1.0 x 13 mm resulted in an increase in ferrosilicon drainage rate of between 1.3 - 1.8 m3/m2/h depending on the flow rate and slurry density with a reduction in moisture and medium carryover of between 1.0 – 1.2 % and 14.1 – 20.2 kg/t/m respectively. For magnetite, the drainage rate increased between 1.0 - 1.4 m3/m2/h as the slot width increased from 0.63 x 8.8 mm to 0.8 x 8.8 mm while an increase in slot length from 0.63 x 8.8 to 0.63 x 12 mm only resulted in an increase in drainage rate of 0.1 - 0.5 m3/m2/h.

Jan 1, 2018

By A. Kamali Moaveni, A. Boehm

"The current research study addresses a physical separation process of basic oxygen furnace slag “BOF-Slag” (also called Linz-Donawitz “LD” slag) for the removal of phosphorous. In order to recycle the LD-Slag into the steelmaking process, the physical dephosphorization methods are considered. The systematic geometallurgical investigation carried out on particle classes of decreasing size, which were further subdivided into susceptibility classes, shows intimate intergrowth beyond 40 µm due to slag´s fast cooling rate. Generally, LD-slag is constituted of oxide and silicate phases, among which di-calcium silicate “C2S” dominates. About 0.5 mass% of phosphorous was detected in the LD- slag, which is exclusively situated in the lattice of the C2S. The comparatively high grinding resistance (Rittinger index 12.9 cm²/J) of the LD-slag reflects the energy demand to liberate the phosphorous carrying phase from the iron containing minerals, while separation efficiency decreases in the very fine particle size range. Hence, the conversion of the phase intergrowth pattern was considered alternatively to re-build the mineral phase structure of the material to a separable interlock pattern. Carbon dioxide, as the most convenient substance in the steelmaking plants, was applied to digest the C2S in the presence of water and to reduce the basicity of the slag slurry. As a result of C2S-CO2 chemical reaction, calcite and calcium silicate are precipitated at the surface of the oxide particles and carried between 25% and 75% of the total phosphorous, respectively. Accordingly, the mobility of the phosphorous content phase to the top of the grains serves the possibility to separate the precipitated layer by mechanical attrition process. This paper is focused on the impact of the intergrowth pattern alteration on the slag´s separability characteristics. Moreover, the operating conditions of the carbonization process, such as temperature and pressure, on the deconstruction kinetics of the C2S and the generated products will be considered. INTRODUCTION The steelmaking BOF-Slag is a stony aggregate waste from the steel manufacturing process. The investigated slag by the current research work was provided by voestalpine steelmaking plant in Linz, Austria. The current legislative situation in Austria restricts the historical application of slag as construction material, due to the high level of heavy metals content and corresponded land-filling and transportation costs of slag, therefore the demand for recycling of BOF-Slag to the steelmaking process has raised, as an alternative application. Statistically, voestalpine steelmaking plant produces about 130 kg BOF-Slag per ton of final steel product, which serves annual BOF-Slag production of 700,000 ton, approximately."

Jan 1, 2018

By S. Banisi, A. Haji-Zadeh, H. Asadi, M. Maleki-Moghaddam

One area in AG/SAG milling field which has received a great attention is the optimization of liner design for any application to increase the availability of mills. The Gol-E-Gohar iron ore concentration plant uses three 9m × 2.05m autogenous mills (AG) in parallel in a dry operation. The AG mill shell is lined with three series (57 cm each) of 36-row liners. Due to large variations in feed characteristics and inadequate blending, the performance of AG mills has been lower than the target value. Therefore, to improve the comminution efficiency, the optimization of the design of AG mill shell liners was applied in this plant. By simulation it was found that increasing the liner lifter face angle from 7 to 30° while maintaining the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. Measurement of the wear profiles of shell liners indicated that the wear along the liner length was not uniform and the highest wear occurred between 0.5 m and 1.2 m of the mill length. A new liner design was proposed by redistributing the metal from parts with a lower wear rate to the parts with a higher wear rate to arrive at a uniform wear profile along the liner length at the liner removal time. The non-uniform shell liner was constructed and installed in one of the three parallel dry AG mills. It was found that the first and second liner designs increased the mill throughput by 2.6 and 7.5%, respectively. After conversion to SAG milling on the account of liner change, 18% (from 413 to 489 t/h) increase in throughput was realized. It was predicted that the non-uniform liner designs will increase the liner life time by 10% and will reduce the scrap metal from the current value of 59% to 50%.

Jan 1, 2014

By Vinay Jain

Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. One of the methods by which this problem might be addressed is by design/screening of suitable reagents (flocculants/depressants/collectors) which act selectively towards either aluminum containing minerals (gibbsite and kaolinite) or iron bearing minerals (hematite and goethite) in order to separate them. Our earlier work indicates that separation of iron oxide minerals from gibbsite is relatively more difficult than from kaolinite. Accordingly, our research work has been focused on finding selective reagents for iron oxide ? gibbsite separation. We have performed density functional theory (DFT) computations to evaluate the interaction energies of seven different reagent groups - carboxylic acid, flotol, hydroxamic acid, phosphonic acid, iminobismethyl phosphoric acid, xanthate and starch with hematite and gibbsite surfaces. The objective was to identify if any of these groups show selective adsorption towards one of the mineral surfaces. Among all these reagents, starch exhibits the highest selectivity towards the hematite surface with a difference in interaction energy of ~63 kcal/mol between hematite and gibbsite surfaces. This is consistent with experimental findings at our laboratories on slime samples from Noamundi mines wherein it is being observed that usage of starch as a flocculant does lead to an improvement in the final grade of the ore with significant reduction in the Al-content. A binuclear complexation mechanism based on affinity between Fe and Ostarch atoms combined with a geometrical templating effect, arising out of a close correspondence between Fe-Fe distance on the hematite surface and O-O distance in starch, is proposed to explain the strong adsorption of starch on hematite surface. Keywords: slimes, iron ore, alumina, hematite, gibbsite, DFT, adsorption, flocculants

Sep 1, 2012

Flinders Power, formerly NRG Flinders, is considering the possible use of low rank coal from Lake Phillipson, South Australia (SA) in its power stations at Port Augusta, SA. Typically, this coal contains about 35% moisture and 10% ash. Unfortunately, it also contains high levels of sodium (1% Na) and chloride (0.95% Cl) with a Na2O level in ash of 18.9%. Such levels cause serious problems during coal combustion, making the use of as-mined coal impractical for power generation. This paper describes the development of an aqueous leaching technique to remove 90% of the sodium and chloride and to yield a product with a Na2 O level in ash of less than 3%. Small-scale agitation leaching tests with good quality tap water at ambient temperatures showed that the coal needed to be crushed to minus 5.6 mm to obtain maximum removal of water-soluble sodium and chloride in 30 min. Leaching kinetics, but not the ultimate removal of salt, were enhanced by the use of higher temperatures (up to 150°C), but this was deemed uneconomic. Varying the pulp density between 20% and 50% had little effect on extractions and there was no benefit in multiple stage water washing. The best results by water leaching were 69%~74% extraction for sodium and 95%~97% for chloride, meaning that the sodium removal was well below the target level. From SEM examinations of the leached product it was concluded that the remaining sodium was organically bound to the carbon atoms in the coal. Further tests using aqueous solutions containing cation exchange additives such as calcium chloride (CaCl2) or ammonium chloride (NH4Cl) or sulphuric acid (H2SO4) showed that significantly enhanced sodium extractions were possible and target specifications were met. Two options, namely a single-stage and a two-stage leach, were then investigated. In a single-stage leach with additive, minus 5.6 mm coal was leached at 33%~50% solids for 30 min at ambient temperature and then filtered and washed with fresh water. This gave a sodium removal level of about 81% and a Na2O level in ash of about 5%. These levels do not quite meet tar-get specifications. In a two-stage leach, the coal was first leached with water alone without an additive as in the single stage leach, and the washed residue re-leached under similar conditions for about 5 min with an additive (CaCl2), and then filtered and washed. This gave a cumulative sodium removal of 96% and a Na2O level in ash of 1.4%~2.4%. These levels are well within target specifications.

Jan 1, 2014

By M. Y. Zhou

The paper elaborates on the significance of producing ultra-low-moisture ore concentrate, the operating principle and technical features of thermocompression- filtration process, the kinetics involved in the dewatering process, and the technological process system and equipment used. It is pointed out that it is possible to reduce the moisture of fine ore concentrate to a minimum. By way of example, the case of the treatment of flotation molybdenum (Mo) using the thermocompression- filtration process is cited.

Jan 1, 2014

By K. Takahashi

Generally speaking, wastewater coming from the metallurgical process for recovering precious metal contains precious metals such as gold (Au), platinum (Pt), palladium (Pd), Silver (Ag), etc., which concentration is about 10 mg/L. In addition, there are other metals such as copper (Cu), iron (Fe), which concentration varies from several mg/L to more than 10,000 mg/L. It should be noted that the concentration of metals in wastewater is relatively high, considering the fact that these metals of similar concentration can be found in ores. However, most of these valuable metals are not treated, due to the high processing cost and technical problems. Within this frame, the authors put forward a new process that includes neutralization/reduction, precipitation and fusion. The idea is to recover and recycle Au, Ag, and Pd metals as well as protecting the environment by saving the resources. It was found that this new process was able to recover more than 90% of Au, Ag and Pd.

Jan 1, 2014

Traditional mineral processing techniques are more and more difficult to recover the increasingly low grade phosphate ores today. Although bioleaching method has been attempted to process low grade ores in hydrometallurgical field due to economical and environmental reason, it has been hardly used in leaching phosphate ore at home and abroad. Strains of Acidithiobacillus thiooxidans and Acidithiobacillus ferrooxidans were collected and separated from the acid drainage of a coal mine in Anhui province of China. Ultraviolet irradiation and Microwave inducement were applied to the bacterial cultivation process to produce strains of Acidithiobacillus thiooxidans and Acidithi-obacillus ferrooxidans able to tolerate extremely low pH conditions and generate sulphuric acid by oxidizing elemental sulfur or sulphide and the mutagenesis can achieve higher leaching rate. The bioleaching result will improve more by the addition of Tween series surfactants.

Jan 1, 2014

By J. Finch, F. Rosenblum, McGill University

The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to potentially hazardous to life and infrastructure. It is essential that there be a reliable test methodology that can categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral combinations making it difficult to predict their self-heating behavior a-priori based on mineralogy or with a simple "snapshot" test. Furthermore, self-heating behavior will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to predict the latent self-heating hazard of a sulphide material. Several of the methods were compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.

Jan 1, 2014

By Bo Feng

The development of surface charge of serpentine mineral and implications for sulphide ?otation have been studied through flotation tests, sedimentation tests, zeta potential measurements and optical microscope photos. The results show that the serpentine mineral was positively charged at an extensive pH range, with an isoelectric point (IEP) of 11.9. The magnitude and sign of the pyrite particles were pH dependent and were negative for pH values above 2. At pH value 9, where ?otation of nickel sul?de ores is routinely performed, serpentine and pyrite particles attract through an electrostatic mechanism. Slime coatings of serpentine adhere to the surface of pyrite, reducing pyrite flotation recovery. The removal of magnesium ions from the serpentine surface by acid leaching results in a decrease of serpentine IEP and eliminates the adverse effect of serpentine on pyrite flotation. Therefore, it has been clearly established that the surface charge value developed in the serpentine/aqueous electrical interface is a function of the serpentine surface incongruently dissolution. As a result of hydroxyl dissolution, the magnesium ions are left in serpentine surface, which is responsible for serpentine surface charge. The methods, which can remove magnesium ions from serpentine surface, can be used to eliminate the adverse effect of serpentine on pyrite flotation.

Sep 1, 2012

By N. I. Tyushkova

This is a brief survey of the technological solutions for deep cleaning of baddeleyite?s concen-trate. Baddeleyite is part of kamaphorite of composite apatite-magnetite ore in alkaline-ultrabasic mountain range of Kola Peninsula. Baddeleyite?s concentrate, which is being produced by Kovdorsky GOK (ore mining and processing enterprise) contains 97.5%~98.5% (Zr?2 + ?f?2) and also scandium oxide (0.05%). It is usually used without any chemical processing. World demand for zirconium oxide is constantly on the rise. Its consumption grows in ceramic industry and in high-tech spheres. That?s why the demand for its purity is very important nowadays (additional cleaning from phosphorus, silicon, iron, aluminium). The mechanism and kinetics of interaction of activated bad-deleyite with sulphuric acid has been studied as well. While applying method of mathematical mod-eling it was confirmed that the mechanical activation is effective for the intensification of sulphation process of baddeleyite?s concentrate with the aim of purifying it from dirt. The use of the calculated optimal regimes allows to reduce such technological operation factors as: temperature, the du-ration of process, the sulphuric acid consumption. It also allows to determine the conditions of anticipatory abstraction of scandium and main dirt in solution in comparison with zirconium oxide.

Jan 1, 2014

By F. Henríquez

Traditionally, the implementation of an automated control for a ball mill has been a challenging one. First, it must be capable of processing a variable SAG mill feed while at the same time avoiding to become a process bottle neck. Second thing is, it must deliver an adequate quality product (P80) to the process downstream. Then the ball mill itself and its associated classification equipment has problems of its own: it must maintain adequate control of cyclone?s pressure, density and pump-box level with often, less manipulated variables than needed, namely, variable pump speed and the opening/closing of cyclones. Thus, it becomes a non-linear multi-variable type of process with often too multiple and contradictory control objectives to satisfy simultaneously. On top of that, to extend cyclones availability and yet, maintaining their performance, is must both for process and maintenance purposes. Trying to solve the puzzle, Minera Los Pelambres implemented a novel and successful combination of MPC (Multivariable Predictive Control) and advanced control in two of its newest ball mills, reducing considerably process variability while maintaining high throughput and keeping the process well within constraints limits. Because of their differences in processing capacity, size and topology, two different stabilizing-control strategies were developed, tested and tuned. Hence, for both control approaches their implementation process, main results, areas of applicability, limitations and their key performance indicators are discussed further. This paper also discusses the need of such advance control technologies in the mining industry, including the impact of these technologies on best practices for their implementation, operation and long term sustainability

Sep 1, 2012

By A. M. Ozbayoglu

Gross calorific value (GCV) of coals was estimated using artificial neural networks, linear and non-linear regression techniques. Proximate and ultimate analysis results were collected for 187 different coal samples. Different input data sets were compared, such as both proximate and ultimate analysis data, and only proximate analysis data and only ultimate analysis data. It was observed that the best results were obtained when both proximate analysis and ultimate analysis results were used for estimating the gross calorific value. When the performance of artificial neural networks and regression analysis techniques were compared, it was observed that both artificial neural networks and regression techniques were promisingly accurate in estimating gross calorific values. In general, most of the models estimated the gross calorific value within ±3% of the expected value.

Sep 1, 2012

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes are diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favors a different flotation environment. An improvement in the kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferential recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rpm, rotor size/type) at the beginning of the row, where flotation is typically froth phase limited and operational, and set-up parameters have a limited influence on the recovery. ? Higher-powered flotation machines (high rpm, high power rotor size/type) at the end of the row to improve fine particle recovery. ? Lower-powered flotation machines (low rpm, low power rotor size/type) to enhance coarse particle recovery. In evaluating the effect of turbulent kinetic energy on flotation performance, the spatial distribution and its effect on size denominated recovery needs to be evaluated. The mean energy dissipation rate is a measure of the bulk energy input, but CFD-based models offer a more introspective view of flotation sub-processes. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced air and naturally aspirated machines. Keywords: CFD-based model, attachment, detachment, energy dissipation, hybrid energy flotation?, forced air, naturally aspirated

Sep 1, 2012

The major components of sylvinite ores, sylvite (KCl) and halite (NaCl), are separated by flotation. Since both these minerals are water-soluble, the process is carried out in a saturated brine, 6~7 mol/L aqueous solution of NaCl and KCl. C16~C22 primary amines, utilized as a collector, are practically insoluble in water. In commercial potash ore flotation operations these amines are melted by heating up to 70~90°C. They are then neutralized with hydrochloric or acetic acids, and such a hot emulsion/dispersion is introduced to the flotation pulp (which is at room temperature). This is immediately accompanied by the appearance of a white precipitate in the system. As our measurements indicate, the Krafft point of dodecylammonium chloride in concentrated electrolyte solutions is much higher than 80°C, and the Krafft point of C16~C22 amines is substantially higher than that. Introduction of a hot amine emulsion into a pulp, at temperature much lower than the Krafft point for the utilized amines, must cause precipitation of the amines. Some of these species are obviously flotation-active. It is interesting to observe that in summertime, when temperatures are high-er, longer chain amines perform better. It demonstrates that the colloidal amine species that precipitate serve as active species in the potash flotation. Therefore, at higher pulp temperatures, when the temperature difference between the pulp temperature and the Krafft temperature of the utilized amine is not sufficiently large, a longer chain amine, the amine with a higher Krafft point, is more efficient. The results reveal that premixing of an alcohol such as MIBC (common frother) with the amine significantly improves flotation performance of the amine. In the presence of such an alcohol the amine disperse system becomes less turbid, and the rheology of the system less non-Newtonian. All this indicates that MIBC, which does not operate as a frother in a potash flotation system, when used as a co-surfactant, enhances the dispersion of the amine colloidal system. The appearing colloidal species perform as an active form of the collector.

Jan 1, 2014

Micro-fine disseminated molybdenite was ground in a laboratory stirred mill using steel media and zirconium media respectively. The floatability of ground molybdenite and slurry chemistry was investigated. It was found that the total recovery of ground molybdenite using zirconium media was higher while the pH and Eh of the slurry are lower than that using steel media. When steel media was used, iron oxy-hydroxides had been generated coated on the surface of molybdenite, and decreased the floatability of molybdenite, especially of the -10µm particles. The iron and lead oxy-hydroxides was generated by the reaction between steel media with pyrite and galena associated with molybdenite. It was also found that changing the grinding media to inert can benefit the flotation of molybdenite. Keywords: stirred mill, grinding environment, floatability, micro-fine disseminated molybdenite, fine grinding

Sep 1, 2012

By T. Fraszczak, U. A. Peuker, T. Mütze, T. Leißner, A. Wikedzi

The present paper highlights on the comminution and liberation properties of two greisen-type lithium bearing-mica ore blends (L1, L2) subjected to different breakage devices; cone crusher (CC), roller crusher (RC), rotor beater mill (RBM) and a screen mill (SM). The particle size distribution (PSD) of the products from each device were evaluated to search for an appropriate PSD model using Gates-Gaudin-Schuhmann (GGS) and Rosin-Rammler (RR) functions. In order to determine an appropriate function that could better describe the PSDs from the devices used, the coefficient of determination (R2) was used as a criterion. In terms of mineral liberation studies, due to costs, only products from rotor beater mill (RBM) were examined through an automated scanning electron microscope (SEM) technique. It was found that RBM, RC and SM products were better described by the RR model than the GGS model with higher R2 values (0.97-1.0). However, cone crusher products for L1 were better described by GSS model, while that for L2 were better described by RR model. In terms of the spread of size distribution as indicated by RR model parameters, RC products were more uniformly distributed compared to products from other devices, for both ore blends. Also the RBM products were more scattered than products from other devices. The results indicate that the composition of individual ore blends affected the comminution products PSDs since different PSD model parameters were obtained for samples comminuted by same devices. The modal mineralogy of the two ore blends indicate both to be rich in quartz, topaz, zinnwaldite and muscovite. Further, the result indicate that, for both ore blends, zinnwaldite phase is more enriched in the fraction < 250 µm. Moreover, better liberation of zinnwaldite is observed for L1 compared to L2. This could be explained by differences of the two ore blends in three aspects; the nature of mineral association, reduction ratio of the fractions analysed and the nature of spread of the size distribution.

Jan 1, 2018

By Ritva Tuunila, Antti Häkkinen

"Wet stirred milling is one of the most effective grinding methods in producing very fine powders in large scale production, but it is a very energy-intensive process, especially when pigments or even nanosize particles are produced. Therefore, optimization of the process parameters is important. The specific energy consumption is a function of stress energy, which describes the effect of tip speed and media characteristics on grinding, and is related to the number of stress events during milling. In effective grinding, a large number of stress events are necessary. The stirrer configuration influences the number of stress events and their intensity, because the motion of the media and the suspension are caused by a rotating stirrer. The effect of three different stirrer types: a pin, disc and blade stirrer, on the grinding rate, i.e. product fineness and specific energy were investigated in this study with a batch laboratory stirred mill with two tip speeds. The material used in the experiments was calcium carbonate. The results obtained with the smaller tip speed showed approximately similar grinding rates and energy consumption for all stirrer types. When looking in closer detail, the blade stirrer seemed to give the finest product with all grinding times compared to the pin and disc stirrers, which both produced almost the same product fineness with the same grinding times. The specific energy consumption was the smallest with the disc stirrer, but not very big differences were obtained. With a higher tip speed, greater differences occurred both in grinding rates and specific energy consumption. The blade stirrer was the most effective in grinding, and the pin stirrer the next. The net energy consumption for the blade and pin stirrers was almost the same, but it was slightly higher for the disc stirrer."

Jan 1, 2014

By R. C. Dunne

A review of the current ?state of the art? of refractory gold treatment will be provided. This will include a global perspective of refractory processes past and present and the location of currently operating plants. Some discussion on the challenges that face the refractory gold industry will also be provided. Keywords: refractory gold treatment, flotation, roasting, pressure oxidation, bacterial oxidation, preg-robbing gold ores, fine grinding.

Sep 1, 2012

By ?. Kostadinov

Theoretical study of the behavior of grinding medium presented by TBP (tetraballpebs) was conducted by computer modeling of the position of grinding medium at different speeds and different drum fill factor. For the modeling were used known equations of motion derived for the ball load. Algorithm was created by SolidWorks software, allowing determination of center of gravity of the load in the mill and energy for grinding. These results were compared with similar results obtained by ball grinding medium. The capabilities of both grinding media are demonstrated by graphics under the following conditions: 1.Equal dimensions of the experimental model of the mill; 2.Equal mass of the grinding loads; 3.Comparison of grinding bodies with the same number, mass and density. Keywords: simulation, behavior, grinding medium, balls, tetraballpebs

Sep 1, 2012