Search Documents

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been conducted, thereby providing a unique opportunity to examine the geochemical evolution of a sulfide rich mine>tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% alumino silicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, S042-, Cu, Zn and Pb (up to 10 000 mglL, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively). In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tin oxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SOi-, Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents. Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massivesulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By T. Melfi, M. James

Attaining required mechanical properties in welds made using the double submerged arc welding (DSAW) process is difficult, and it is becoming more difficult as the strength level of the base materials continues to increase. Producing weld metal with adequate mechanical properties involves factors that are often overlooked and not taken into consideration. Not least amongst these problems is simply finding information to use in selecting the appropriate flux/wire combination. Most of the available data on flux/wire combinations provided by consumables manufacturers is generated using the multiple pass welding procedures required for classification per specifications such as AWS A5.17 and A5.23. This data really gives no insight into the properties that can be expected in a DSAW application. Also, base plate composition plays a very significant role because of the fact that base plate dilution can be as high as 70% in DSAW welds. This means that if any elements are present in the base metal that are deleterious to mechanical properties, they will also be present in significant quantities in the weld deposit. Some of these elements can decrease toughness and increase hardness (increased hardness is a concern if the pipe is intended for sour service). Some of these problems can be mitigated by proper selection of welding consumables. Selection of proper welding consumables means selecting an electrode that provides the appropriate alloying elements to obtain the desired level of impact toughness while also keeping the hardness within any specified limits. In order to attain the necessary impact toughness, selection of a flux with an appropriate composition (in terms of its basicity and its ability to control the nitrogen content of the weld deposit) is required. As with all welding processes, the mechanical properties of DSAW welds are also highly dependent on the welding procedures. This work clarifies how to select appropriate consumables to meet a given set of requirements, and also how to achieve the optimum mechanical properties from those consumables.

Jan 1, 2005

By D. Houghton

"I am very pleased to be a member on this panel today because abrasion and wear in mills has been part of my life over the past forty years. My presentation will deal with the role Ni-Hard has played in combating wear and abrasion in mills. Before Ni-Hard came along, unalloyed white iron was used in ball mills and one of the most popular types of white iron liners was the pocket liner. Slide #1 illustrates the design of the pocket liner used at Dome Mines in their 5' x 22' pebble mills. The pockets filled with grinding media and it was on this that the wear took place. The concept is not unlike the new magnetic liner which utilizes the ore and grinding media to form the wearing surface. In this slide please note the tapered pocket type of cored bolt holes. If cored bolt holes do not fill with grinding media there could be excessive grooving or wear at that area. Therefore all cored bolt holes should be tapered in this manner.Before Inco patented the name Ni-Hard several foundries were making the alloy iron under different brand names such as Diamond Alloy, Mitchelloy and Specialloy. In the early days some of the Ni-Hard was poor quality. Inco provided foundries with technical knowhow and provided assistance to licence them to sell under the name of Ni-Hard. This was in the late 1920's. The material we are discussing is Ni-Hard type I with the following analysis (slide #2). It is a martensitic white iron with BHN of 550 - 600 and is a relatively easy alloy to produce in either a cupola or electric furnace. The annual average production of Ni-Hard in North America is 90,000 tons with mill liners making up 25,000 tons and grinding media 30,000 tons, according to Warren Spear of Inco."

Jan 1, 1983

By N. H. Grace

"IntroductionA STRIKING FEATURE of the past twenty years has been the application of organized scientific and industrial research to problems of national defence and security and to the development of our natural resources. It has been shown that effective research improves public health, increases the productivity of land, makes mineral wealth available, and increases the efficiency and productive capacity of industry. Alberta is a region bounteously provided with a variety of natural resources, and the Province has entered into a period of unprecedented industrial development. There is, surely, a great opportunity to bring scientific research to bear •on problems associated with the development of these natural resources.I propose to spend a little time discussing the term 'research', indicating something of the various types of research and those fields which appear to •be the particular responsibility of government bodies. It seems logical, also, to outline the course of development .of industrial and scientific research in the English-speaking world during the past twenty-odd years.Research is investigation, examination, or enquiry, and involves the application of human thought, and actions, to the unfolding of new knowledge. That knowledge may assume a variety of forms. Fundamental knowledge may be new facts related to some form of matter, to motion, space, thought, and so on. Those engaged in applying the natural sciences have no monopoly on research as this term is equally valid for those engaged in obtaining, sorting, relating, and interpreting the facts of history, literature."

Jan 1, 1952

By J. B. Evans

"THE OPPORTUNITY to participate in a CIM seminarconcerning the direction of mining engineer trainingis perhaps fortuitous as it comes at a time when theengineering schools which have invited inspection byCanadian Accreditation Board of the Canadian Councilof Professional Engineers are examining theirrespective curricula.Currently there exists considerable soul-searching in various engineering schools across Canada where questions such as the following are being posed.- Have we achieved the correct balance between subjects related to technical methodology and subjects devoted to conceptual planning and design?- Should we include ""applied humanities"" in our program? (Whatever ""applied humanities"" might mean!)- Should courses covering pollution control, ecology, economics, technical writing, professional conduct and ethics be offered as compulsory subjects, as electives, or not at all?- Is it a better scheme to have students complete an Arts or Science degree before entering engineering?- Do we place too much emphasis on pure mathematics and sciences with the result that insufficient time is available for instruction in the engineering applications of these subjects?- Should English expression and/ or literature be included in the engineering programs and, if so, should these subjects be presented by the English department or by English lecturers captive to the engineering school? - Is the present program directed primarily at research activities rather than preparing engineers for their future roles in industry? - Should we teach our own versions of mathematics and physics? - Do we have sufficient engineers on the faculty strength or are we overloaded with Ph.D.'s from the pure sciences? - How flexible should the program be, what should the compulsory vs elective course content be, and what freedom of choice, if any, should be given with respect to elective courses? - To what extent should students contribute to faculty decisions?- How far should we pursue computer science subjects and do we need to make our students proficient in computer programming? - How far should operations research and mathematical models be carried in the undergraduate program when the students have limited experience in the real engineering world? - Realizing that an engineer never completes his education, should the undergraduate program cover ""bare bones"" engineering and should instruction in particular disciplines be left to graduate schools and / or industry?"

Jan 1, 1972

By John C. McKay

"The five papers which follow, under the heading of ""Technology Transfer-Universities to Industry"", were originally presented at the 20th Annual CIM Conference of Metallurgists in Hamilton, Ontario. They are a unique group of papers, unique because each paper is concerned with applied research done wholly or partly in a university environment and then translated into industrial practice.Universities can rightly be regarded as one of our nation's greatest resources-a veritable storehouse of knowledge and expertise. Yet, too often, this resource is overlooked or, at best, sparingly used by Canadian industry. Of course, university-based research cannot supplant industry-based research, nor vice versa; each type of research activity has its proper role in the over-all process of technology development.University-based scientists are best equipped to conceptualize, innovate, determine viability of basic premises and to verify these at the bench or small pilot-plant level. Industry based scientists are best equipped to develop ""bench-scale"" innovations into mature manufacturing practices. Thus, university-based scientists and industry-based scientists do not compete with, but rather complement, each other. Active, relevant university research enhances industrial research provided good communication between the two ""solitudes"" is continually nurtured.Good communication between industry and university is a prime objective of CSIRA/ACRIS (Canadian Steel Industry Research Association /Association Canadienne pour la Recherches dans d'Industrie Siderurgique), The directors of CSIRA/ACRIS foster improved communication by making regular visits to universities, by sponsoring projects and by providing lists to professors of uncharted areas where basic research is needed. More can be done to improve communication between industry and university, and it is the intent of the Association to do more.The five papers sponsored by CSIRA/ACRIS are examples of good communication and healthy cooperation. It is interesting to note when reading these papers that the cooperation arose, in each instance, as a result of different circumstances. However, there is a common thread and it is personal acquaintanceship-the university scientist/professor and the industry investigator/manager knew each other prior to the initiation of the project."

Jan 1, 1982

By W. K. Muwais, R. G. Cuddy

"The Lower Cretaceous McMurray Formation contains the bitumen reserves of the Syncrude Mine in northeastern Alberta. This formation comprises sediments deposited sequentially in fluvial, estuarine and marine depositional environments. The Syncrude Base Mine area consists mostly of estuarine sediments, as much of the original marine sediments have been eroded away. These estuarine deposits consist of channel-fill sediments and interchannel tidal flat sediments with the channel-fills comprising most of the orebody.Channel-fills contain, among other lithologies, interbedded sand, silt and clay rich layers that often occur as sequences of inclined beds with dips up to 25 degrees or more. A detailed knowledge of the distribution of these inclined beds, their lithological characteristics and their continuity is very important in assessing the risk of mine highwall instability . Techniques used to identify and characterize adverse structures are reviewed. INTRODUCTIONGeneralThe Syncrude Canada Ltd. oil sand mine is located within the surface mineable portion of the Athabasca Oil Sands area about 40 kilometres north of Fort McMurray in northeastern Alberta, Canada (Fig. I). The company commenced large-scale strip mining of oil sands in June 1977in the area, referred to as the Base Mine, situated in the southeast corner of the company's two lease areas (Fig. 2).The mining method (Fig. 3) utilizes large electric drag lines operating on a single bench with highwall depths up to 60 metres. Feed grade oil sand (= 6 wt.% bitumen) is mined by draglines and windrowed parallel to the highwall crest. Lower grade oil sand « 6 wt. 0J0 bitumen) occurring as waste bands is selectively mined by the draglines and cast back into the mined out pit or placed on the bench and hauled by truck. The windrowed feed is delivered to the extraction plant by a bucket wheel reclaimer and conveyor system. Stripping of Recent, Pleistocene and Cretaceous overburden units is done outside the conveyor systems by mobile equipment. The 4.5 kilometre long mine is split into four quadrants for planning and scheduling purposes, with each quadrant having an individual dragline-bucketwheel-conveyor system.Surface mining of oil sand at Syncrude requires the removal of vast quantites of material. The design of the open pit mine relies heavily on knowledge of the distribution of ore and waste materials, and on the physical characteristics of these materials.The geology of the oil sand below the dragline bench at the Syncrude Mine is complex. Geological, geotechnical and hydrogeological factors play an important role in the design and operation of the mine. This paper describes aspects of the geology that impact on the design and operation of the mine. Some of the methods and procedures adopted by Syncrude to successfully overcome difficulties that the complex geology creates are discussed."

Jan 1, 1989

By E. Bratygin, G. Gazaleeva

"The article describes the analysis of methods and criteria of selectivity of optimal ore preparation schemes. Traditional criteria based on study of physical-mechanical properties of ores give the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production.Further on estimation is given to different criteria of the crushing selectivity, the new criterion is offered, the definition of which is done by results of an optical microscopy– the estimation of a valuable mineral release degree. The final estimation of the crushing process selectivity L? is performed by a calculation of a ratio of the valuable mineral free grains quantity in a desired size grade of a crushed material to the valuable mineral free grains quantity in a desired size grade of a raw product.Besides, optimality assessment of using the specific crushing unit is preliminary performed according to a maximum crushing degree of a material, however, the priority is given to the maximum selectivity criterion. The check of the proposed criterion was done when comparing the crushing of niobium bearing ores of the Vishnevogorskoye deposit in cone inertial and centrifugal impact crushers. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion L? showed that the centrifugal impact crusher (CC) has the value of the selectivity criterion lower than the cone inertial crusher (CIC). For the crusher CC the criterion L? is 0.82 – 0.87 units, whereas for the crusher CIC – 1.43-1.755 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 120°, peripheral speed of a cone rotation – 1,420 rpm, specific energy consumption – 6.99 kW?t/t.INTRODUCTIONIt has been shown that the most efficient techniques of mineral raw materials disintegration are selective crushing enabling to produce liberation of particles at maximum use of destruction techniques by borders of minerals cleavage. These days, such techniques are usually called special disintegration techniques (Jankovic & Valery, 2015), and they are used in 3–4 crushing stages. The selection of optimal crushing techniques is performed based on the following main parameters:- degrees of crushing, calculated based on granulometric features of raw and crushed products;- selectivity criterion defined according to useful mineral release and slime ability degree; and- traditional criteria (Gazaleeva et al., 2015) of choice based on study of physical-mechanicalproperties of ores gives the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production."

Jan 1, 2016

By J. Oliver, B. Wilson, 10

"Red Dog is one of the world’s largest zinc producing mines and a significant producer of lead and silver. While some of the operational challenges relate to the mine’s location in a remote part of Alaska, there are also challenges in the mineral separation process. Recent processing upgrades have included the installation of two M5000 IsaMills to improve the zinc regrind circuit and of one Jameson Cell to improve the pre-flotation circuit. Relatively fine grinding is required to achieve efficient mineral separation at Red Dog, but while fine grinding aids in the production of high grade concentrates, it also creates challenges in the efficient recovery of fine minerals. Over half of the lead lost to the lead circuit tailings, as well as almost half of the zinc lost to the final tailings, is in the finer size fractions (<10 µm). The high pulp density experienced in the pre-flotation and lead rougher circuits also causes significant entrainment loss of lead and zinc to the pre-flotation concentrate and of zinc to the lead concentrate. To help improve fine mineral recovery, Red Dog has recently plant tested and installed magnetic conditioning technology in the flotation circuits. The equipment aggregates fine paramagnetic sulphides and selectively increases their flotation recovery. This paper outlines the testing and positive results at Red Dog.INTRODUCTIONRed Dog is the largest zinc mine in North America and represents approximately 29% of North American zinc concentrate production. The mine is located in northwest Alaska, approximately 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The remote location makes the mine accessible only by air or seasonally by ocean-going barges. Red Dog is a partnership between NANA Regional Corporation Inc, the land owner and Teck Alaska Incorporated, the operator of the mine. Red Dog Ore and Mineralogy The Red Dog deposit is a rich sedimentary exhalative (sedex) zinc-lead-silver deposit. The main minerals present in order of abundance are: quartz, sphalerite, pyrite, barite and galena. Production began in 1989 with mining of the Main deposit. Between 1989 and 2012, approximately 55.6 million tonnes of ore with an average grade of 20.5% Zn, 5.6% Pb, and 97 g/t Ag was mined from the Main deposit. Subsequent to the development of the Main pit reserve, two additional open pit deposits were discovered: Aqqaluk and Qanaiyaq. The first blast in Aqqaluk occurred on June 4, 2010. As of December 31, 2014, the Aqqaluk deposit reserve is an estimated 45.7 million tonnes of ore with an average grade of 15.1% Zn, 3.9% Pb and 71 g/t Ag."

Jan 1, 2016

By L. Chunpongtong

Compared to equipment used in hard rock mines, the lifespan of equipment deployed in oil sands operations tends to be shortened due to the abrasive nature of the material and soft ground conditions in which it operates. One of the challenges of oil sands mine planning is to determine the most cost-effective replacement time for aging equipment. For cost engineers dealing with aging equipment, the options become an economic trade-off between taking the chance of higher frame failure or buying new equipment. Therefore, the ultimate question is: “When is the best time to replace the equipment?”

Jan 1, 2012

By J. A. E. Bell

"Inco has shifted part of its traditional extractive research effort at its J..Roy Gordon Research Laboratory in Mississauga toward new, value-added products. Most of the effort is being expended on new Ni powders for batteries and new Ni-coated products which will be produced in Inco&apos;s carbonyl nickel refineries. New products under development are Ni-coated powders, Ni-coated fibres and ultra-fine Ni powders. Other new products for advanced material applications include controlled expansion composites, NiGOLD strip, Thermal barrier coatings on Inco alloys, and plasma coatings.Research and Corporate Strategic ThrustsThe newest strategic thru st of the company is to increase the value of the primary metal products. These new products are to be in addition to any new alloys or downstream alloy fabrication.Historically Inco has had the highest research expenditures in the extractive metallurgy field in North America. This has resulted in many new processes including flash smelting , matte separation, fluid bed roasting, pressure carbonyl refining and cobalt electrowinning which have contributed to establishing Inco as the lowest cost nickel producer. The recession of the 1980s caused a restructuring of Inco research and corporate goals .As shown in Figure I, from 1975-1982, i.e. pre-recession, Inco spent around 33 million dollars per year on research. Some 48070 of that sum was spent in Corporate Laboratories in Sterling Forest in the United States and in the United Kingdom , mostly on alloy associated research. A further 10% was spent on alloy research at the alloy production facilities in Hunting- ton, West Virginia, and Birmingham and Hereford in the United Kingdom. On extractive research, 13% was spent by process technology groups at the plant s, 20% at the pilot plants in Port Colborne and 9% at the J. Roy Gordon Research laboratory.The relative research expenditures (Fig. 2) have decreased so that today they are at the same level as 1975-80. The research as a per cent of sales has been cut from 2.2% to 1.2% of normalized sales. A normalized sale price of $4.00/lb Ni was used in the 1988 figures. This was partly achieved by closing Corporate Laboratories. Most of the essential alloy research was moved to producing plants and total alloy research is now 27%.A new thrust initiated in the 80s was mining research which now accounts for 20% of research expenditures. Over a period of the past five years this research has doubled the mining productivity in Inco. The pilot plant expenditures have been cut in half. One entire research station at Port Colborne was converted into a platinum group metals intermediate refinery. The decrease in pilot plant expenditures has been compensated by full scale plant trials devoted to the S02 abatement program at Sudbury."

Jan 1, 1990

By Lassi Klemettinen, Ari Jokilaakso, Dmitry Sukhomlinov, Pekka Taskinen

The solubilities and distributions of molybdenum and iridium in iron silicate slag and copper-iron mattes were studied using an equilibration-quenching technique and subsequent direct phase composition analyses by EPMA (Electron Probe X-ray Microanalysis) and LA-ICP-MS (Laser Ablation-Inductively Coupled Plasma-Mass Spectrometry). The equilibrations were carried out on a wide matte grade interval, ranging from 55 wt-% Cu to 75 wt-% Cu, in pSO2 = 0.1 atm at 1300°C. The results in equilibrium with a solid iridium-molybdenum alloy indicated an iridium solubility of 150–500 ppmw in the sulphide matte, depending on the matte grade, and a molybdenum solubility of 100–600 ppmw. Iridium was distributing predominantly in the sulphide matte with the distribution coefficient of 10+3 - +4 but molybdenum deported predominantly in the slag with Lm/s(Mo) = 0.02–0.1. The effects of alumina and lime additions in the smelting slag were also examined. INTRODUCTION Iridium is a highly siderophile element (HSE), which means that it is incompatible with the sulphide forming elements and possesses a small solubility in mattes, such as copper- and nickel-iron sulphide melts. Molybdenum behaves only modestly in that way (Walker & Li, 2008; Righter et al., 2017). They both are known to be trace elements accompanying copper and nickel sulphide ores. No solubility data, however, are available for them in copper-rich sulphide mattes. Geochemical data on the behaviour of Ir and Mo deal mostly with low-iron silicate systems, e.g. basaltic melts, and high-sulphur sulphide solutions and mattes (Ertel et al., 2008; Fonseca et al., 2007). They also indicate that Ir and Mo dissolve in silicate melts primarily as oxides and not as electrically neutral metal species. Most geological data of iridium focus on high-sulphur systems of the monosulphide composition and typically Fe-Ni mattes where copper is a trace element (Fleet et al., 1996; Sattari et al., 2002). Direct solubility measurements for mattes and iron-lean silicates have also been made using pure Ir or an Ir alloy as the saturation phase (Borisov & Palme, 2000; O’Neill & Eggins, 2002; Makovicky & Karup-Møller, 1999; Ertel et al., 2008; Mungall & Brenan, 2014). A recent summary about the solubilities of HSE’s in iron- and sulphur free silicates is available in Laurenz (2012). The thermodynamics of molybdenum partitioning between oxides and Fe-S-O melts was studied by Mengason et al. (2011). Their results indicate strong accumulation in the iron-rich sulphide in reducing conditions (pO2 = 10-9.6 atm in Ni-NiO equilibrium at 1050°C). Molybdenum dissolves in iron-lean silicate melts as MoO3 species in oxygen pressures above the Fe-FeO equilibrium and as MoO2 in more reducing conditions (Farges et al., 2006; Righter et al., 2017).

Jan 1, 2019

By J. W. Matousek

Since the late 1800s, copper-nickel ores have been mined and smelted in the Sudbury area. The Canadian Copper Company, the Copper Cliff ancestor of Inco Limited, commenced operations with a blast furnace smelter in 1888. Coal-fired reverberatory furnaces were added in 1911 and multihearth roasters in 1914. The blast and reverberatory furnaces smelted, respectively, coppernickel ores and ore fines until 1930, when a milling process and plant began operating to concentrate and separate the minerals of these two metals. Two reasons for this delay were: (1) the availability of high grade ores suitable for direct smelting; and (2) the difficulties in making the copper-nickel separation. The Mond Nickel Company, however, practiced flotation at its Coniston Smelter site from 1914 to 1930. A bulk concentrate containing six per cent copper and five per cent nickel was recovered from ore of 1.6 per cent each of copper and nickel. Gravity (table) and magnetic concentrates were also produced. Inco Limited (then The International Nickel Company) began laboratory-scale flotation tests on its ores in 1918. This work led, ultimately (in 1930), to the construction of the 7500 tonne-per-day Copper Cliff Mill, designed to recover separate copper and nickel concentrates. Its capacity was expanded to 11000 tpd in 1936, to 18 000 in 1940, and to 27 000 in 1942. Since 1971 it has operated to process only the bulk flotation products from other mills to yield individual nickel and copper concentrates.

Jan 1, 1999

By J. E. Armstrong

"Pinchi Lake and Bralorne Takla mercury mines; Canada's only producing mercury mines during the past war (1939-1945); occur within the Pinchi Lake mercury belt. This belt is in central British Columbia; and is approximately 150 miles long extending from southeast of Fort St. James northwest to the headwaters of Omineca river.During the field season of 1937 cinnabar was discovered by J. G. Gray of the Geological Survey in Permian limestone on the north shore of Pinchi lake, where the main showings of the Pinchi Lake mercury mine were later developed. Following the publication of Gray's report claims were staked in the spring of 1938, and later that year were optioned to the Consolidated Mining and Smelting Company, and in June 1940 a reduction plant with a rated capacity of SO tons a day was brought into operation. In 1943 the plant had a capacity of more than 1,000 tons a day. The grade of ore treated was reported to average S to 10 pounds of mercury a ton, and production during the years 1940 to 1944 exceeded 4,000,000 pounds. The Bralorne Takla mercury mine, which is 90 miles northwest of the Pinchi Lake mercury mine, was brought into production in November 1943 with completion of a 50-ton mill. During the next 10 months more than 100,000 pounds of mercury were recovered, and the grade of the ore was reported to average 15 to 20 pounds of mercury a ton. During the war, production from these two properties was far in excess of Canadian requirements, and Canada was able to supply the United Kingdom and United States with part of their need.s. Both properties ceased operations during 1944, and, due to an excessive supply of mercury, have not yet reopened. The Pinchi Lake mercury belt lies along a northwest-trending major fault zone called the Pinchi fault zone (Fig. 1). This zone is approximately 150 miles long and varies in width from 200 to 1,000 feet . It forms the northeastern edge of a northwest trending fault belt up to 10 miles or more wide in places. In general the northeastern margin of the Pinchi fault zone represents the contact between closely folded, stratified Permian rock:s on the southwest and Mesozoic formations and Omineca intrusions on the northeast. It seems probable that the fault zone marks the site of major thrust faulting from the southwest and that the Permian rocks moved up with respect to the Mesozoic formations. Intense faulting occurs in the Permian rocks within the fault zone. There the more important faults trend north and northwest, dip steeply west and southwest, and may join a major low-angle thrust fault at depth."

Jan 1, 1954

By Jeremy D. Glennon

A number of exciting challenges, opportunities and unanswered questions remain concerning the chemistry, geochemistry, medical, industrial and analytical applications of gold and its compounds.1 Among the challenges presented is the need for extraction methods for gold, at process and indeed analytical scales, that avoid the use of organic solvents or hazardous reagents. Extensive environmental contamination has occurred in the Brazilian Amazon from the mercury-gold amalgamation process. Major problems with the cyanidation process are the relatively slow dissolution kinetics and the health and environmental problems associated with it. With innovation and technical changes, a cleaner way for solubilising and extracting this versatile precious metal can be found. This cleaner future may lie in supercritical fluid science. Interestingly, geochemical studies of gold solubility and speciation in hydrothermal solutions have highlighted the importance of supercritical conditions and sulphur species in the deposition of gold in natural environments. Gold solubility in supercritical brines is far higher than previously supposed while interest in the high content of carbon dioxide in the mineralizing fluids is growing. 2,3 In recent years, also, there has been a tremendous amount of attention paid in analytical chemistry and in industry, to the area of supercritical fluid extraction (SFE) of organic and metallic species. 4 This interest has been fuelled by the introduction of more stringent environmental control and the subsequent need for cleaner solvents and processes to replace established ones. Carbon dioxide is the substance of choice for SFE because of its moderate critical parameters (Tc = 31oC, Pc = 73atm), inertness and availability in pure form. It is an excellent extraction medium for non-polar and moderately polar species, and with careful ligand design, it can be used for analytical and process scale metal extraction from solution and solid phases. In general, the dissolution of a metal in supercritical CO2 (sc-CO2) requires that the charge on the metal ion be neutralised on complexation by the ligand or through a form of ion pairing (analogous to the situation where metal ions are extracted into organic solvents, such as methyl isobutyl ketone or toluene). In this way, then, many chelating agents such as dithiocarbamates and hydroxamic acids have been utilised to extract metal ions such as Cu and Fe into sc- CO2, the process greatly enhanced by the use of fluorinated ligand derivatives. 5-7 In this review paper, we show that supercritical conditions and complexation with sulphur donor atoms, important in the natural deposition of gold, can form the basis of a clean, eco-friendly chemistry for gold extraction. Analytical scale extractions of gold from a variety of matrices can be conveniently used to assess the efficiency of any new proposed ligand.

Oct 1, 2003

By Brooke Clements

The Buffalo Head Hills region is located approximately 350 kilometres northwest of the city of Edmonton in northcentral Alberta (Figure 1). The Alberta diamond joint venture consisting of Ashton Mining of Canada Inc., Alberta Energy Company Ltd and Pure Gold Minerals Inc. began exploring for kimberlites in the Buffalo Head Hills region in late 1996. At the time, the Mountain Lake diatreme, located 200 kilometres to the southwest, was the only reported kimberlitic rock in Alberta (Leckie et al., 1997, Figure 1). Exploration efforts since 1996 have successfully identified a new diamondiferous kimberlite province in Canada.

May 1, 2001

By John D. Lupton

This paper will discuss the benefits and advantages of using 3D survey data in stope analysis. Obtaining detailed 3D survey data of underground mine progress and production is a challenge. It is almost impossible to ?see? around corners, underneath overhangs, or deep into dark, dusty, humid underground voids. Thus, valuable ore can remain permanently encased in backfill. Without the benefit of 3D survey data, underground mines have the difficult task of meeting grade quotas without the benefit of knowing exactly what has been mined. Lack of this data usually results in unfavorable month end Reconciliation factors, where grades must be adjusted to match grades assessed by the Mill.

Apr 1, 2005

By Michael Bowker

Au/TiO2 catalysts were prepared by incipient wetness impregnation and tested for the room temperature photocatalytic reforming of methanol in aqueous solution. These catalysts proved to be more active, on a molar basis, than Pd/TiO2. The dependence on loading of gold was different from that of palladium, showing a double maximum in yield at 0.1 and 2 wt. % with low rate below 0.01% and above 10%. A model is proposed for the reaction involving band gap excitation of titania electrons which are used to oxidise the methanol via adsorbed CO. With palladium, photoreforming of CO and water can be achieved, but this is much less effective on gold, presumably due to the much weaker bonding of CO on Au.

Oct 1, 2003

By Min-Sung Kang

Excavation and earthmoving equipment mostly operate in accident-prone areas. These areas normally have rollover, confinement, and fall or may be considered harmful work areas due to demolitions and sewage removals. It is inevitable that excavation and earthmoving systems should be developed to secure the safety of operators through unmanned and remote control systems. Therefore, this research proposes a system that enables excavators to be unmanned and remote controlled without any renovation, remodeling, change, or transformation by applying attachable and separable mechanism and modules. Moreover, this research proposes the sensor module to evaluate the dynamic status without processing remodeling or transformation the existing hydraulic drive excavation system by adopting the easy attachable and separable mechanism. The study verifies this proposal based on observed possibility and feasibility through the experiments.

Aug 1, 2013

By Roy Sage

Overview ? History ? background to current programs ? Kyoto status ? Support for technology development ? Support for GHG reduction ? Sources of information History ? 1988 - Toronto Conference - The Changing Atmosphere ? Proposed target ? CO2 levels reduced to 20% of 1988 levels by the year 2005 ? 1992 - Canada signed Framework Convention on Climate Change at the UN Conference on Environment and Development in Rio de Janeiro in June 1992 ? Canada launched the National Action Plan on Climate Change ? Kyoto protocol adopted in principle in 1997

Nov 1, 2002