Search Documents

By W. H. White, A. J. Sinclair

"Unaltered biotites from three samples of monzonite and gabbro from the Copper Mountain stock and a single sample from a pegmatic biotite-chalcopyrite vein cutting the Triassic Wolf Creek formation have a mean K-A age of 193±7 m.y. These data support a suggestion based on geological evidence that Copper Mountain ore deposits are related genetically to the Copper Mountain stock.A cogenetic mineral pair (biotite and clinopyroxene) from a sample of sericitized and chloritized monzonite of the Copper Mountain stock have identical K-A ages of 150 m.y., which probably represents a time of wide-spread, post-ore, hydrothermal alteration. This alteration is believed to be related genetically to a group of post-ore intrusions known as the ""mine dykes,"" suggesting that they also have an age of 150 m.y."

Jan 1, 1968

By E. Norton

"Even though the subject of this panel discussion is dust control, rather than dwell on the design aspects of dust collection systems which are well documented in numerous publications, :it was considered more pertinent to the present economics of mining to examine the energy costs involved.At the present time, the facts of shrinking fossil fuel reserves and spiralling fuel costs are being constantly brought to our attention. Industry is being motivated to consider the possibilities of incorporating heat recovery systems in areas where they prove to be economical. Unfortunately, it is not a simple exercise to determine if the installation and operation of heat recovery equipment is feasible and economical. Each process involving heat recovery potential must be thoroughly studied in all aspects.In a paper presented at the 1975 Annual General Meeting of the Canadian Institute of Mining and Metallurgy in Toronto, Ontario, entitled ""The Influence of Energy Conservation on Concentrator Design"", it was stated that the largest single energy consumer in winter is space heating with the largest portion of this supplied to crushing and screening plants. (1) Within the scope of this panel discussion we will study, as one example, a crushing and screening plant using natural gas heat in the province of British Columbia and we will explore the feasibility and economics of installing air-to-air heat recovery equipment."

Jan 1, 1976

By Xian Jian Guo, Lei Li, Hua Wang

The distribution and behavior of As, Pb and Zn elements in the copper smelting process were investigated using thermodynamics. The differences between thermodynamics evaluation and practical smelting processes were analyzed. The main factors affecting the distribution of the elements are oxygen enrichment in blowing, copper matte grade and smelting temperature. In general, the distribution ratio of As, Pb and Zn to off gas increases with the smelting temperature and decreases with oxygen enrichment in blowing. Meanwhile, their distributions in matte decreases and that in slag increases with the increase of copper matte grade. There is some gap in distributions between thermodynamics evaluation and practical smelting processes. INTRODUCTION The copper concentrates usually contain a number of minor elements, the control of which in copper smelting processes is often a key to the quality of the anode copper produced and may also have a bearing on the overall economics of the process (Yang et al., 2017). Knowledge of the thermodynamic properties of the minor elements in slag is very important in the control of the slagging reactions (Takeda Y, Ishiwata & Yazawa, 2007). In addition, the environmental contamination caused by the minor elements associated with copper-bearing ores, such as As, Pb and Zn, has become more and more important (Wang, 2004). Arsenic, lead and antimony, which are all carcinogenic metalloid elements, are usually contained in iron-rich wastes, and theirs emissions are considered to be one of the foremost environmental concerns (Wang, 2004). It is important to elucidate the elements distribution of them in the reducing-matte smelting process. The distributions of As, Pb and Zn elements in the copper smelting process are dependent on many factors, including the temperature, raw material composition, reduction atmosphere, concentration level, and slag chemistry etc. (Chen L Z, Xu X, 2016). Generally, these minor elements mainly distribute in phases of gas, copper matte and slag in the smelting process (Shu, Wang, & Qu, 2016). The arsenic exists mainly in the form of sulfo-arsenides in the copper concentrate, and it will decompose and be oxidized in the smelting process (Chen & Lu, 2016). Part of the products, including AsS, AsO, As2 and As2O3, evaporates into the gaseous state, and some other part enters into slag phase in the form of As2O3 and As2O5 (Wang, Guo, & Tian, 2017). Meanwhile, the As2O3 in the slag phase can also be reduced to metallic As and combine with Cu, S, Fe forming Cu3As2, As2S3 and Fe3As2, and then enter into copper matte. During the copper smelting process, about 50% of zinc enters into slag phase in the form of ZnO and 45% exists in the copper matte in the form of ZnS. Little volatizes into the gas phase. Most lead exists in forms of PbS and PbO in the copper concentrate, and it is mainly distributed in copper matte in the smelting process (Zheng & Lin, 2015).

Jan 1, 2019

By Osvaldo A. Bascur

Industrial complexes rely on measurements of flow rates, qualities, and concentrations for monitoring and optimizing their operation. Corporations use the data from the various sensors and measurements to make business decisions, which affect the profitability of the operation. However, gross errors, due to a variety of reasons like faulty sensors, bad instrument calibration, or incorrect process models may corrupt the actionable information supplied to operations, quality managers, and maintenance personnel. The solution is to use the sophisticated new tools to model the process, sift through the available data to locate the gross errors, and use statistical data reconciliation to validate the sensors and instruments. In this way the data are unified to give the most accurate plant information for use by the monitoring and decision making processes. Most mining and metallurgical plants use predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis, and oil and lube analysis for critical equipment. Process control strategies are installed in several metallurgical sites. All of these depend on reliable and accurate data. The data unification methods validate the individual measurements by using the concept of balances and statistical techniques where each instrument is no longer independent of the other measurements in the facility. This paper refers to the data unification and analysis methods required for profitable plant operations. Continuous improvement and monitoring of the measurement system at the plant and analysis of the reconciled data provide the best information for the decision-making process. On-line gross error detection and elimination methods are required to ensure efficient evaluation of process performance and process optimization. An open discussion of the new methods for gross error detection and data unification will be presented.

May 1, 2001

By C. Gu

Flow field design is critical for PEM fuel cells. The flow field design can affect reactant distribution to the catalyst surface, water management, thermal management and current collection. Therefore, it has tremendous impacts on the fuel cell performance and durability as well as reliability and operational flexibility. In this paper, an optical method is used to study the reactant distribution in the flow field channels of two commonly used flow field designs, straight channel design and serpentine channel design. Images of the flow patterns are shown followed by discussions of the flow patterns.

Jan 1, 2005

By D. K. Sarkar, Ying Huang

"Superhydrophobic thin films were fabricated on aluminum alloy substrates by chemical etching followed by passivation with organic acid molecules; (ii) electrophoretic deposition (EPD) of functionalized ZnO nanoparticles and (iii) electrodeposition of organic-inorganic composite materials. The physical and compositional analyses of the deposited thin films were characterized by SEM, FTIR, XRD as well as contact angle goniometer. The contact angle and surface roughness of the superhydrophobic surfaces prepared by the chemical etching process were found to be 156° and 2.29 µm, (ii) by the EPD process were found to be 155° and 4.54 µm and (iii) by the electrodeposition process were found to be 159° and 7.11 µm, respectively.The corrosion properties were analyzed with both polarization and electrochemical impedance spectroscopy (EIS) in NaCl aqueous solutions. The results demonstrate that the superhydrophobic thin films on aluminum alloy substrates display better anti-corrosion behavior than the as-received aluminum substrate. The comparison of results pertaining to the compositional and corrosion properties of these thin films on aluminum will be discussed in this work.INTRODUCTIONSuperhydrophobicity is defined as a surface property which provides non-wetting characteristics with a water contact angle larger than 150°. It is observed that the creation of certain micro-nanoroughness structures promotes the entrapment of air in the spaces of the rough surface morphology. In addition, lowering the surface energy helps to reduce the affinity of water drops to the surface, thereby weakening the water-surface interaction. Recently, various fabrication methods for superhydrophobic surfaces have been explored (Sarkar, 2010, Huang, 2010, 2011, 2013, 2015a, 2015b), such as the sol-gel process (Brassard, 2011), plasma treatment (Marchand, 2013), chemical vapor deposition (Zheng, 2009), chemical etching (Saleema, 2011), electrodeposition (Ying, 2011) and electrophoretic deposition (EPD; Huang et al., 2015b)."

Jan 1, 2016

By P. Au, R. Kearsey, D. Y. Seo, Patnaik. P. C.

Three nickel based superalloys (7.5%Cr+5%Co+2%Mo+1%Ti+5%Al and Ni balance (wt%)) containing different amounts of W and Re were produced in the single crystal (SX) condition utilizing the Bridgman casting process. First, the effect of different levels of Re, and W on chemical microsegregation were investigated by EPMA quantitative analysis, and eutectic phase fraction analysis. Second, in order to investigate the effect of these refractory elements addition on oxidation behaviour, isothermal oxidation testing of the SX nickel based superalloys was conducted at 1000°C for 277 hours under 3 ppm moisture content of air in a thermogravimetric analyzer (TGA). All three SX nickel based superalloys revealed an excellent SX solidification structure with a common primary dendrite arm spacing of -250 µm and a large fraction of ?/?' eutectic located between the secondary dendrite arms. From the average EPMA compositional results, with the exception of Ni, elements such as Cr, Co, Re, Mo, and W all tended to segregate towards the dendrite core during solidification, while Al, Ti, and Ta were present in greater quantity in the last liquid phase to solidify, which resulted in large eutectic ?/? ' phases to form within the interdendritic regions. As the nominal level of Re increased, microsegreagation of Re, W, Cr and Mo increased, indicating that Re had a much greater influence on partitioning behavior compared to W. Figure la shows the specific mass gain as a function of exposure time for each alloy. An alloy with 2wt% of W and Re (Alloy B) exhibited less weight gain compared to two other alloys with either higher content of W or Re (Alloy A and C). Microstructural and compositional analyses of oxidized samples were conducted using SEM and EDS. Figure lb shows the typical surface morphologies of the oxidized Alloys A and B. It is evident that more oxide nodules (indicated by arrows in the figure) were presented in Alloy A. It is speculated that the amount of these nodules was responsible for more mass gain in Alloy A compared to the two other alloys. From the examination of the longitudinal section of the oxidized samples as shown in Figure 2, for Alloy A, nodules actually penetrated deep into the material. For Alloy B, however, a relatively uniform and continuous oxide layer was developed and deeply attacked areas were not observed. It was also found that preferential oxidized regions were located at the area between the ?/?' eutectic phase and the dendrite arms where the concentration of refractory elements was relatively high. Therefore, it is plausible that the oxidation kinetics of these alloys is related to the extent of microsegregation.

Jan 1, 2004

By D. Ibarra, J. Jacob, A. G. Guezennec, P. d’Hugues, A. Archane

The lack of adequate gas mass transfer is a rate limiting step in many bacterial leaching processes. Oxygen often becomes a limiting factor because of its low solubility compared to the high demand induced by sulfide oxidation. One way of increasing the solubility of oxygen in water or in media solution is by increasing the driving force, i.e. raising the oxygen partial pressure in the gas stream supplied to the leach pulp. The use of oxygen is a well-known practice in high-temperature bioleaching reactors (above 70°C) whereas air is usually preferred in medium and low-temperature operations in order to avoid too high dissolved oxygen concentrations which could impact negatively the bacterial activity. The purpose of this study was to investigate the use of oxygen-enriched gas in bioleaching reactors at 40°C in order to improve the gas transfer in the system when operating at high solid load (20% and more). Bioleaching experiments were performed on a sulfide-rich tailing waste (pyrite 60%, copper 0.8%, cobalt 0.06 %, gold 1 g/t) using the “BRGM-KCC” bacterial consortia. The reactor used for the tests was designed on the basis of a new bioleaching reactor concept developed by Air Liquide, Milton Roy Mixing and the BRGM which uses floating agitators to inject gases and to mix and to suspend solids in the bioleaching solution. Two types of tests were carried out: with air injection and with oxygen enriched gas mix injection. The aim of this work was to confirm the capacity of bacteria to grow and to dissolve pyrite in this type of bioreactors in oxygenrich atmosphere, and to compare sulfides dissolution rates during both types of bioleaching tests. The results obtained show that the use of oxygen enriched gas mix does not decrease bioleaching performances compared to air injection. High metal extraction yields were achieved (above 80%). No deleterious effect due to oxygen use was observed on the bacteria despite the high level of dissolved oxygen reached in oxygen tests (up to 14 mg.L-1).

Jan 1, 2016

By R. B. Casault, J. D. Boyd, D. R. Bell

"Full-scale sections of three different types of Grade 483 line pipe have been evaluated extensively. The variations in chemical composition, optical microstructure, tensile properties, hardness and Charpy impact toughness with specimen orientation and location were determined. Significant variations in several properties, notably Charpy shelf energy, impact transition temperature, inclusion content and ferrite grain size, were observed for different locations in the pipes. The results indicate that current specifications call for test samples for the most conservative locations, except for impact tests. Minimum Charpy impact values generally occur at the II2-width location, which may be a more appropriate specified test location than the present I/4-width location. The anisotropy of impact toughness, and the importance of low sulphur content and inclusion shape control for adequate toughness in the transverse/rolling-direction orientation were demonstrated. The orientation of impact specimens is critical for spiral-weld pipe, and the current specification test is non-conservative in that it can give results which are two to three times higher than the minimum value for the steel.IntroductionThis report presents the results of an extensive metallurgical evaluation of three different Grade 483 line-pipe steels. The sample material came from full-scale sections of line pipe, which represented current commercial practice at the time of manufacture (1975-1977). Since then, significant improvements have been made in the manufacturers' procedures for producing skelp and pipe, and the line-pipe specifications have been revised. Hence, the information in this report is dated in terms of current design, but it is unique and significant in several respects:"

Jan 1, 1982

By M. P. Brameld, G. Archambault, R. H. McCorkell

"The rates. J. at which materials emit radon are of interest in studies of the sources of radon in mines. buildings. soils overburden and other places where it may indicate the location of ore or be a health hazard. Here J values were determined by measuring the radon concentrations by means of scintillation counters or alpha-particle track detectors in chambers in which specimens were sealed. Errors in the measurements due to leakage from the chambers. lack of secular equilibrium in the decay series of the radon measured, or the limited rate of diffusion of radon from powders or within the chambers were shown to be insignificant or could be corrected. Scintillation counter measurements are highly reproducible; track detector measurements also appear useable and may be made on many small samples using small, simple chambers. J measurements were made for uranium ores, drill cores, standard CANMET pulps. concrete and gypsum board. Powdering of ores had little effect on their J values.IntroductionIn the mining and mineral sciences, radon (222Rn) is of interest chiefly for two reasons: in geochemical exploration for mineral deposits its presence in soil. overburden and water in more than background concentrations may indicate the existence and locations of uranium deposits and, if present in sufficient concentrations, it is a possible health hazard in mines, mills and other places where people live and work. The latter aspect of radon's role has received considerable attention recently(1,2,3,4,5), and surveys of soil-gas radon concentrations have been used for some time in searches for uranium deposits(6,7,8,9,)."

Jan 1, 1981

By Jun Shan

The preparation of poly(N-isopropylacrylamide)-monolayer-protected clusters (PNIPAM-MPC) of gold nanoparticles was carried out in a homogeneous phase using three ways, in which three types of PNIPAM ligands were employed. The first type comprised of PNIPAMs with narrow molar mass distributions, synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization and thus, bearing a dithiobenzoate at the chain end. These polymers were used directly to passivate the gold nanoparticles upon the Schiffrin reaction in a one-pot synthesis. The second type of ligands was derived from the first one through hydrazinolysis, and they therefore contained a thiol end group. The third type of ligands was PNIPAMs obtained through conventional radical polymerization, post-modified to contain thiol end groups. The PNIPAM-MPCs were characterized by high-resolution transmission electron microscopy, and by dynamic light scattering. The one-pot synthesis utilizing the ligands of the first type turned out to be a simple and facile method, compared with the other two ways, with which the size of the gold nanoparticles can be easily manipulated mainly by adjusting the molar ratios of PNIPAM / HAuCl4. PNIPAM is a more efficient ligand to stabilize the gold nanoparticles in water and in organic solvents than alkanethiols. The surface density of PNIPAM chains ranged from 1.8 to 3.6 chain/nm2, which is much lower than that typical for alkanethiols. The thickness of a PNIPAM monolayer bound to the gold core is somewhat larger than the size of the random coil of corresponding free PNIPAM in aqueous solution, which suggests that the conformation of a PNIPAM chain bound to the gold core is to extended.

Oct 1, 2003

By Tobias Riedel, Peter Ay, University of Applied Sciences, Bianka Bade, Nicole Pausch, Bernhard Gemende, Florian Logsch, Matthias Leiker, Satyanarayana Narra, Claudia Glaser

This study focusses on the production of micro-structured agglomerates with high porosity from iron (III)-hydroxide-containing materials as adsorbent. A fractal-like structure of the agglomerates was created through a two-stage agglomeration process. Developing porous structures was necessary to increase the adsorption capacity. Various materials were used for the agglomeration experiments: i) filter cake (dry matter content 23 to 27 wt.-%); ii) FerroSorp®DGµ, a product which is already being used commercially for various applications in water cleaning. These materials in the pristine state have different characteristics such as dry matter content and particle size distribution. The desired optimised agglomerates can be achieved with the help of additives or binders, respectively. Additionally, the agglomeration process parameters play a vital role. In order to produce agglomerates with high porosity, the process was carried out in two steps. Firstly, FerroSorp®DGµ (d90 < 30 µm) was agglomerated jointly with the aforementioned filter cake in an Eirich intensive mixer (particle size range 125 µm < d90 < 500 µm). The second agglomeration step post drying was carried out in a pelletisation disc or in an Eirich intensive mixer with the addition of polymeric binders (up to particle sizes ranging from 2 to 4 mm). Agglomerates were characterised both in short and long term loading tests using phosphate as model ion. Contact times were less than 10 min, similar to practical application in percolation columns, or more than 7 days, respectively. The results show that the agglomerates produced in the two-stage pelletisation process have more advantageous properties like better accessibility of the active sites obtained by specificly influencing the particle size distribution during the two-stage pelletisation process.

Jan 1, 2016

By R. Siwik, N. K. Davé

"The national reactive tailings (RATS) program is a co-operative industry-government effort to develop practical techniques for closure of reactive tailings areas. This paper summarizes the RATS program objectives and areas of research, and details the Noranda/CANMET project on the Waite Amulet tailings.Geophysical and biohydrogeochemical investigations were carried out at an inactive copper-zinc mine tailings site, Waite Amulet, in Noranda, Quebec. Geophysical investigations consisted of seismic, electromagnetic conductivity and electrical resistivity surveys to determine the thickness of the layers above bedrock and to map conductivity variations within the tailings and the immediate outlying area. Biohydrogeochemical investigations consisted of installing multilevel piezometer nests to determine groundwater flow patterns and porewater chemistry, obtaining solid core samples and characterizing for physical, chemical and mineralogical parameters, and iron oxidizing and sulphate reducing bacterial counts.The geophysical survey indicated a bedrock ridge extending under the tailings from the northeastern outcrop which may act as a porewater boundary layer. The survey also indicated a 2 to 20 m clay layer underlying the main tailings dam. Preliminary results of the saturated zone porewater chemistry have indicated three major zones of high electrical conductivity varying between 1,000 to 12,000 µs and pH between 3.4 to 8. Lower pH and high metal and sulphate concentrations were obtained in a shallow zone near the water table. With depth, the concentration of metal and sulphate ions decreased and pH increased below the water table. The underlying clay layer is relatively impervious -and most of the seepage from the tailings is probably exiting from the sides of the impoundment dam."

Jan 1, 1987

By P. C. Garg

"IntroductionThe Central Mine Planning and Design Institute (CMPDI) of India, started planning the extraction of thick seams highly susceptible to heating in 1977by the French method of sub-level caving and/or multi-slicing. Nitrogen flushing was proposed for inhibition of heating by the author in one such project - the Kotadih colliery.Inhibition of heating was unheard of in the Indian coal industry before 1977-78. The usual practice was to seal off a district or a part of the mine or the entire mine when spontaneous heating occurred. With very little equipment in a normal bord and pillar district and a low production rate, the financial loss in capital assets and in production did not warrant any serious thought for inhibition of spontaneous combustion. With the planned advent of longwall mining, particularly sub-level caving, with heavy capital investment as well as high production potential, the sealing of a longwall face due to spontaneous heating could not be considered an appropriate solution.Principle of Inhibition of SpontaneousCombustionFrench engineers have established that a fire will not break out when oxygen is 15% or lower in the general body of the air. However, once a fire starts, the percentage of oxygen has to be reduced to 2% - 4% to extinguish it. It is this principle which has been used at Blanzy Coalfield in France to inhibit heating and it is claimed that this has retrieved the integral sub level method of mining. Nitrogen infusion has been used in Frence since 1978 to keep the oxygen content below 14% in the goaf."

Jan 1, 1987

By P. Fellner, A. Sýkorová, J. Thonstad, J. Jurišová, V. Khandl

Adsorption of S02 on alumina used in the aluminium industry, so-called smelter grade alumina, was studied in the temperature range 15 C-120 C. The specific surface area of the smelter grade alumina was 88 m2/g. It was found that at temperatures lower than 40 C, sulphur dioxide is bonded to alumina reversibly by physical forces, and the adsorption can be described satisfactorily by the Langmuir adsorption isotherm. The heat of adsorption was estimated to be -33 kJ.mor1. At temperatures in the range 80 C- 120 C, which prevail in dry scrubbers in the aluminium industry, the heat of adsorption was determined to be -56 kJ.mor1. When S02 was adsorbed at temperatures higher than 80 C, about 30 % of the S02 could not be desorbed when heating the samples up to 250 C. In the presence of S02 and oxygen, the formation of sulphate was determined at temperatures above 90 C.

Jan 1, 2006

By Zhongxue Li

This paper reviews an analytical model that defines the relationship of weight-weighted or volume-weighted average haulage distance with bench height and other related parameters, presents the optimum bench heights under various conditions in terms of minimizing the weighted average haulage distance of ore/waste during the full lifetime of an open pit mine, and discusses the truck haulage economics of mining open pits by high bench, specifically by 15 m, 18 m and 20 m benches through marginal analyses. The observations from these analyses disapprove the previous conflicting assertions that the over-all weighted average haulage distance either increases or decreases directly with bench height. It is concluded that: (1) an increase of bench height to 15 m from 12 m is likely to be viable under the general conditions of large-scale deep open pit mines; (2) the reduction of haulage cost is much limited with the case of increasing bench height to 18 m from 15 m; and (3) the feasibility of mining open pits by 20 m benches is generally questionable. These conclusions may serve as a useful guide for those who advocate open pit mining by high bench.

Jan 1, 1995

By Maria Skyllas-Kazacos

The All-Vanadium Redox Flow Battery that was pioneered and has been developed at the University of New South Wales (UNSW) in Sydney since the mid-1980s is currently regarded as one of the most attractive energy storage systems for large-scale implementation in a wide range of grid-connected and offgrid applications. Several companies are now manufacturing and installing MW-scale VFBs in applications ranging from renewable energy storage, load-levelling, emergency back-up power and power arbitrage. The full-scale uptake of the VRB in commercial energy storage systems however, is heavily dependent on the availability and cost of vanadium used in the VRB electrolyte. Cost is also a function of purity requirements and although there is little scientific evidence on the effect of impurities on the VRB life and performance, VRB developers continue to demand high purity vanadium at considerable cost. This paper will provide a brief overview of the current understanding of electrolyte impurities on VRB performance together with an economic analysis of the impact of vanadium prices on overall VRB capital and levelised costs for a range of applications.

Jan 1, 2014

By I. A. Menshikh, S. A. Kotov, N. L. Shinkarkin

All the cycle for conversion of natural and reprocessed uranium of ROSATOM’s “TVEL” Fuel Company is concentrated at the Siberian Chemical Plant. Conversion capacities are located on two sites, i.e. the Radiochemical Plant, which refines feedstock, and the Conversion Plant, which produces uranium oxides and uranium hexafluoride. Liquid radioactive waste arising in the process, after pretreatment, is transferred to a dedicated national operator for underground disposal. Environmental strategies pursued by the Fuel Company involve the introduction of process solutions intended to eliminate liquid radioactive waste and convert it into a solid phase. In the 5–7 years coming, work will be performed to refurbish and upgrade conversion facilities of the Siberian Chemical Plant that will principally change its radioactive waste management scheme. This paper describes the current waste management scheme and sets out planned schemes for management of natural and reprocessed uranium waste, which will be implemented in the refurbishment of conversion facilities of the Siberian Chemical Plant. The new technologies for the management of liquid radioactive waste from uranium conversion described in the present paper have an undeniable advantage over the current technology mainly due to significantly less environmental harm.

Jan 1, 2020

By R. U. Seneviratne, B. K. Ahlgren

In this paper we follow various technological discoveries and developments in the purification of minerals and metals in the mining industry by ion exchange. For approximately 100 years, ion exchange has been a known and variously applied purification and separation technology used by scientists and producers. It would seem obvious that the producer’s objectives have always been to achieve the highest quality products and the lowest operation costs, but also with the least amount of technological complexity. As a strategy to reach these goals, much effort has been expended in the quest to improve continuous ion exchange (CIX) systems by reducing utility needs and resin degradation or loss while at the same time improving productivity and reliability. Recent developments from a number of companies have pushed equipment boundaries, resulting in a variety of unique commercial equipment designs each with a varying degree of success. The challenge set forth for all new designs has been a truly continuous process with no sacrifice in the afore mentioned benefits. One very recent equipment design based on system symmetry appears to meet many of these objectives with greater flexibility and less complexity resulting in better economics for the producer.

Jan 1, 2014

By Z. Xie

Gas diffusion electrodes (GDEs) for high temperature polymer electrolyte fuel cells (PEFCs) have been prepared using ZrP-modified Nafion ionomer. The performances of these GDEs as cathodes and anodes were evaluated and compared with conventional Nafion ionomer GDEs using Nafion 112 as the PEM under elevated temperature and reduced relative humidity. ZrP-modified Nafion ionomer was incorporated into the catalyst layer to enhance water retention and/or increase the protonic conductivity. The fabrication of ZrP-GDEs was implemented by the ion exchange of Nafion solution with zirconyl chloride, followed by the impregnation of GDEs in H3PO4 solution. The composite electrolytes in the catalyst layer possessed a ZrP content of 20% by weight. GDEs were characterized by TGA, SEM, XRD, and CV. Scanning electron microscopy (SEM) indicated evenly distributed elemental Zr and P within the catalyst layer. Cyclic voltammetry shows a reduced electrochemically-active surface area when the ZrP is incorporated into GDEs. Polarization and impedance analyses indicate the cathode with ZrP-modified Nafion ionomer did not show an enhanced or decreased performance, compared with conventional Nafion ionomer GDEs under elevated temperature and decreased humidity. However, when GDEs with ZrP¬Nafion ionomer were used as the anode, an improved performance was observed. Preliminary experiments show that the anode is more sensitive to dehydration than the cathode under elevated temperature and/or low humidity. Improving the anode water retention capability will help to reduce losses at the anode. However, the incorporation of hygroscopic agents in the cathode catalyst layer is not essential because it is self-humidified by electrochemically-produced water even under elevated operating temperature and lower humidity.

Jan 1, 2005