Search Documents

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"Cu ore bodies commonly contain oxide Cu at the surface, with sulfide Cu content increasing with depth. The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Current practice of oxide Cu recovery involves sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors. CPS has shown to improve recovery of oxide Cu but has the following limitations: a) HSE issues with NaSH, b) high consumption of NaSH, and c) inability to recover certain oxide Cu minerals because they are refractory to sulfidization. The oxide Cu flotation is further complicated by the presence of certain non-sulfide gangue minerals which adversely impact both recovery and selectivity.Over the past eight decades, numerous collectors have been proposed and evaluated for the direct flotation (i.e. without sulfidization) of oxide Cu minerals, the most researched of which is alkyl hydroxamate. While there are numerous publications dealing with the fundamentals of interaction of alkyl hydroxamates with single minerals, there are few publications which discuss the practical aspects of alkyl hydroxamate use in ore flotation, particularly their use with sulfidizing agents. Case studies in this paper include methods to identify optimum combinations of sulfidizing agents and oxide collectors to maximize recovery for various types of ores. It was observed that some ores do not require any sulfidization, while others require at least partial sulfidization to improve efficacy of AHX. Depending upon the ore type and mineralogy, recovery improvement in the range of 5 to 15% units, over and above that achieved with CPS, has been observed with the use of AHX. For ores requiring high dosages of NaSH, it was shown that AHX can be used to reduce the NaSH consumption significantly. The challenges associated with the presence of non-sulfide gangue minerals in oxide copper ores are included, and the use of modifiers to alleviate the associated problems and enhance the performance of AHX is discussed."

Jan 1, 2016

By M. Mirnezami, J. A. Finch

The McGill component of the consortium contributed detailed examination of the electrokinetic properties of the constituent minerals, primarily pentlandite and serpentine. Mineral specimens were derived from an ore sample; mineralogical examination showed the serpentine was predominantly clinochrysotile, a fibrous mineral responsible for much of the flotation separation problem. The study included design of a novel sedimentation potential measuring device to classify the surface charge of the ore and electrophoresis measurements on single and mixed minerals which progressively approached flotation conditions. The sedimentation potential measurements provided a general association between surface charge and the visual state of aggregation as a function of pH. The electrophoresis experiments started with single minerals in a background of indifferent electrolyte and progressed to mixed minerals in a background of supernatant derived from an ore sample. The single mineral tests supported the suspected electrostatic interaction, i.e., hetero-coagulation, at flotation pH 9-10. The mixed mineral tests demonstrated this interaction and also revealed hetero-coagulation with Mg(OH)2 precipitates, derived from the supernatant. This interpretation was confirmed by optical and electron beam imaging. A series of agents, CMC, polyphosphate, soda ash, EDTA, were examined to disperse the system. To accommodate the small mass of single mineral available a novel turbidity measurement using a UV/Vis spectrophotometer was introduced. Selected conditions were used in contact angle and small-scale flotation tests.

Jan 1, 2011

By Janice Zinck, Ian London

In recent years, the secure supply of critical and technology metals has become increasingly important tomajor industrialized economies that seek to sustain their industrial base and develop advanced technologies, such as clean energy. Canada, with its significant reserves of rare earth element (REE) and other metals, has an opportunity to supply some of the global demand for these materials. However, to transition from promising mineral deposits to marketable products, investment in strategic research and development (R&D) and expertise is needed to address the complex technological challenges around the production, separation and processing of these metals, and to better understand the global market for these key commodities. To this end, in its April 2015 budget, the Government of Canada committed to invest $23M over 5 years to accelerate production of REE and chromite/ferrochrome. The goal of this program, developed in close association with industry, is that Canada contributes a sustainable supply of REE to the global market. The research and development program will provide the technological capacity to establish a Canadian REE industry. This paper will discuss REE R&D advances achieved in the first year of the program in areas of mineral characterization, beneficiation, leaching, separation and environmental management and will highlight the Canadian model of collaboration where industry (e.g. prospective producers, technology companies), government, academia and other stakeholders work closely to ensure that the R&D is targeted, innovative and effectively deployed and commercialized.

Jan 1, 2016

By R. J. Grant, D. W. Scott, M. A. Cooper, E. R. Shannon

"The Brunswick No.12 site concentrator processes 10,500 tonnes per day of a complex lead, zinc, copper and silver ore producing four concentrates by differential flotation. Research over the years has led to increased understanding about the mineralogical and flotation characteristics of the ore. A pilot plant study conducted at Lakefield Research, primarily designed to investigate the technical feasibility of semi-autogenous grinding, provided an opportunity to test recent theories about grind size,, reagent schedule and flowsheet configuration.A fundamental approach was taken with each of the unit processes involved in grinding and flotation. Basic operating and metallurgical criteria were established in each area and a step-by-step implementation program initiated in the plant.Significant improvements in metallurgical and financial performance have been realized through the application of basic grinding and flotation principles using conventional milling equipment and without major capital expenditure. Current operating practice is detailed and metallurgical advancements cited.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mines near Bathurst, New Brunswick. Brunswick is a publicly traded company with majority ownership held by Noranda Minerals (63%). In addition to the No. 12 underground mine, the company operates a lead smelter and phosphate fertilizer plant in Belledune, N.B. and maintains a 25% interest in a joint venture with Noranda Minerals' Heath Steele mine near Newcastle, N.B. Through the four operations, a total of 2000 people are directly employed with fixed assets totalling Cdn$187 million (BM&S, 1991)."

Jan 1, 1993

By E. Busse, J. E. Burgener, J. G. Eacott, M. C. Robinson, P. E. Burgener

"This paper presents a preliminary assessment of the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from electric arc furnace baghouse dust at a mini-steelplant. Recent studies and literature are referenced briefly as they pertain to the formation and characterization of dust, toxicity considerations and alternative dust treatment and disposal options.Laboratory testwork results, published data, pilot plant experience and anticipated influences resulting from recycling residues are used for the purpose of developing a conceptual design for a caustic leach - electrowinning plant to treat 15,000 tonnes/year of dust at a one million tonnes /year capacity steelplant in Canada.Target economic studies, comprising preliminary estimates of capital and operating costs, revenues and rate of return are presented. Economic and commercial considerations concerning the relative merits of dust treatment at a centralized facility compared with an on-site plant are discussed.IntroductionThe treatment or disposal of mini-steelplant electric arc furnace (EAF) baghouse dust has been given increasing attention in recent years for two principal reasons. Firstly, the dust is now classed as a hazardous waste material under V.S. EPA regulations which prohibit its disposal in dumps other than controlled landfill sites. Secondly, the dust contains certain metal values, notably zinc and lead, which may be economically recoverable, depending on the costs associated with disposal resulting from enforcement of the EPA regulations. Other metallurgical dusts and waste materials, from both ferrous and non-ferrous operations, may require the same considerations as EAF baghouse dust.Several studies have been carried out to examine various aspects of dust treatment but few commercial plants are in operation. Technology employed uses pyrometallurgical techniques. Commercial-scale hydrometallurgical plants are not known to exist although small-scale plants are frequently more economically attractive than their pyrometallurgical counterparts which generally require economies of scale to be viable.The concentration of mini-steelplants in northeast V.S.A. and southeast Canada merits study to determine whether or not dust treatment for metals recovery is a commercially feasible alternative to disposal.This paper examines the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from EAF baghouse dust at an on-site ministeel plant processing carbon steel scrap and discusses economic and commercial considerations pertaining to dust treatment at a larger, centralized facility."

Jan 1, 1984

By Nickvinder Bhath, Johnson Matthey Plc, Jamie Baker, Daniel Kim, Jeff Lucht, Shijie Wang

"Precious metals (PM) in copper anode slimes are traditionally recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of precious metals, including relatively inert metals such as gold and platinum group metals (PGMs). In this paper, a new method to recover PGM from complex and difficult feed streams is described. Using a proprietary Advanced Ion Exchange (AIX) adsorbent which has a high selectivity for PGMs over other metals and can achieve high PGM mass loadings with a series of incredible pilot test data plus the business case generated from the study results are also presented in the paper.INTRODUCTIONPrecious metals in copper anode slimes are traditional recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of many metals, including relatively inert metals such as gold and platinum group metals (PGMs). Fully hydrometallurgical processes for extraction and recovery of gold and silver from copper anode slimes were employed in major copper refineries since 1995, which was first developed at Rio Tinto Kennecott Utah Copper.In Rio Tinto KUC process, the wet chlorination and gold solvent extraction were utilized to enable recovery of gold and silver as well as other metal compounds. The availability of water and the interaction and amenability of gold processing in water-based solution makes it possible that gold and silver are produced in only five days, compared with a traditional pyrometallurgical process that took 45 days. Most copper refineries are still following the tradition, but the use of hydrometallurgical technologies is increasing as the world demand for metals increases, energy utilization, and environmental viability."

Jan 1, 2016

By R. G. McDonald

"High iron solution concentrations often result in the formation of basic ferric sulfate during the high temperature oxidation of sulfidic materials such as base metal and refractory gold concentrates. Consequently, the “Hot Cure Process” followed by limestone neutralization is required to facilitate subsequent processing and/or disposal of the leach residue. The present paper discusses strategies that can be employed to influence the composition and nature of the high-iron content leach residues produced during pressure leaching.INTRODUCTION Control of iron deportment in hydrometallurgical processing remains a key challenge for a range of reasons. Strategies generally relate to the control of conditions under which iron is optimally rejected (Demopoulos, 2009). Supersaturation provides the driving force for crystallization and this can be controlled by a number of factors that include (1) pH and/or Eh control, (2) the presence of matrix anions and impurities, (3) dilution, (4) complexation and dissociation and (5) manipulation of the rate at which the metal to be precipitated is released to solution. Each of these factors is impacted by temperature. Good control of crystallization is essential to the control of precipitate properties such as the degree of crystallinity, stability, particle size and quality which covers both the extent of impurity uptake and suitability of the precipitate for waste disposal. The quality and properties of iron precipitates in turn can impact downstream processing. It is the aim of this paper to discuss the generation of iron-containing residues produced during the pressure oxidation of sulfidic ores and concentrates and how the nature of these can be controlled to potentially facilitate further processing. A brief overview of several related topics will now be given and include, where relevant, discussion of work undertaken in our laboratories. In addition, brief discussions of selected process options that enable good control of iron rejection will be provided."

Jan 1, 2016

By Cheryl L. Allen

The increasing energy costs associated with mining has become an issue that needs to be addressed for future sustainable production. Vale Inco is undertaking a Ventilation on Demand (VOD) Project in an effort to minimize costs, continue to mine at depth and reduce green house gas emissions. A dynamic VOD system is very complex with potential high risk. Therefore, a systematic approach is being taken for successful development and implementation of the concept. The physical components of the system are currently being tested at various Vale Inco mine sites. While the operability of the physical components are being tested, the strategy for optimizing the architectures of the system is being defined. This presentation discusses the method of developing a VOD system at Vale Inco.

Feb 1, 2008

By E. Eccleston, E. Gardner, F. Letarte, R. Schonewille

"In 2005, after nearly a decade of process development and feasibility work, the commercialization of the Falconbridge Nickel Smelting Technology (NST) began in earnest with the design and construction of a grassroots ferronickel plant at Koniambo Nickel in New Caledonia. The NST process was developed as an alternative to the conventional Rotary Kiln-Electric Furnace (RKEF) process for production of ferronickel from saprolitic nickel laterite ores. The NST process promised environmental and energy efficiency advantages over the conventional route. A key step of the NST process involves fluidized bed pre-reduction of calcined laterite ore using direct injection of pulverized coal as the reductant. Two parallel fluidized bed reduction roasters (FBRs) were installed at Koniambo Nickel, each designed for a maximum capacity of 4,200 MTPD of calcined nickel laterite ore. This paper describes the process development and scale-up of the fluidized bed pre-reduction process, the design challenges associated with the prototype commercial units, and the current status of the FBR operation at Konaimbo.INTRODUCTION In the mid-1990s, Falconbridge began to develop a new flowsheet for production of ferronickel from nickel laterite ores. The process that developed came to be known as the Falconbridge Nickel Smelting Technology (NST). The flowsheet, which is particularly appropriate for saprolitic ores, involves several major unit operations, including: drying in a hammer mill-flash dryer, calcination and preheating in a flash calciner, pre-reduction in a fluidized bed reactor, and smelting in a DC arc furnace to produce the ferronickel product. This paper focuses on the fluidized bed pre-reduction step of the process and provides an overview of the process chemistry, laboratory and pilot plant development work, scale-up and commercialization of the pre-reduction step, and the results obtained in the prototype commercial units."

Jan 1, 2017

By André Bérubé

"IntroductionSince the disappearance of Les Forges du Saint-Maurice at the end of the last century, many historians have taken an interest in the lengthy past of this enterprise. They considered the political, socio-economic, administrative and anecdotal aspects of the industry, but barely dealt with the elements of technology. The purpose of this article is to try to fill this gapru.Les Forges du Saint-Maurice was an integrated industrial concern, specializing in the production of semi-finished wrought iron and finished cast iron, that operated almost without interruption between 1734 and 1883. Les Forges first came into being in 1729, when Montreal merchant Francois Poulin de Francheville submitted to the king of France a request for the right to exploit the bog iron ore deposits on his seigneury of Saint-Maurice. This request, agreed to in 1730, was one of a long series of attempts, previously unsuccessful, to establish a local iron industry in the colony. Several such proposals were held up by a lack of capital from promoters or a too rigid application of the mercantilist policy by the metropolis. In 1730, however, the French minister Maurepas favoured a more liberal policy which would encourage private enterprise. The benefits of an iron industry to the naval construction industry was a factor that caught the attention of administrators. The choice of the site for Les Forges was based on the following factors:• the abundance of surface deposits of bog iron ore in the Saint-Maurice region;• the presence of a vast supply of hardwood and conifers needed in large quantities by this industry;• the proximity of sandstone and limestone deposits, indispensable materials for the construction and operation of the blast furnace;• the presence of a water stream, with sufficient flow to provide the hydraulic power needed for the operation of the machinery."

Jan 1, 1983

By R. F. Favreau, R. A. Morin, G. W. Kuzyk, P. J. Babulic, N. J. Tienkamp

"Atomic Energy of Canada Limited is constructing an Underground Research Laboratory (URL) as part of a comprehensive program to evaluate the concept of nuclear fuel waste disposal deep in crystalline rock formations. Careful blasting methods have been used to minimize damage to the excavation surfaces. Good wall quality is desirable in any excavation. In excavations required for nuclear waste disposal, the objective will be to minimize blast-induced fractures which may complicate the sealing requirements necessary to control subsequent movement of groundwater around a sealed disposal vault. The construction of the URL has provided an opportunity for the development of controlled blasting methods, especially for drilling accuracy and optimization of explosive loads in the perimeter and cushion holes. The work has been assisted by the use of blast simulations with the mathematical model Blaspa.This paper reviews the results of a recent project to develop a controlled method of full-face blasting, and compares the observed field results with the results of a blast simulator called Blaspa. Good agreement is found between the two, and the Blaspa results indicate quantitatively how the blasting may induce damage in the final excavation surface. In particular, the rock in the final wall may be stressed more severely by the cushion holes than by the perimeter holes. Bootleg of the rock between the perimeter and cushion rows occurs when the burst out velocity imparted to it by the explosive loads in the perimeter holes is inadequate. In practice, these findings indicate that quantitative rock stress and rock burst-out velocity criteria can be established to minimize wall damage and bootleg. Thus, blast simulations become an efficient way to design controlled blasting and to optimize quality of the excavation surf ace."

Jan 1, 1989

By P. R. A. Andrews, I. Jackman

"A mineral processing investigation to recover chromite was performed at Lakefield Research, under the guidance of CANMET personnel, on a 70 tonne ore sample from the Bird River deposit in Manitoba. In the laboratory phase a flowsheet was developed which involved grinding, gravity separation and flotation. The gravity concentrates were upgraded by magnetic separation and the flotation concentrates by gravity concentration. Pre-concentration by electronic ore sorting, magnetic separation and heavy media separation also was examined.The developed flowsheet was applied on a pilot-plant scale in the second phase of the testwork to the ore as received, and to ore pre-concentrated by electronic ore sorting and magnetic separation. Ore pre-concentrated by heavy-media separation was treated on a laboratory scale based on the pilot-plant flowsheet.Processing the are as received resulted in 77% recovery of chromite in a concentrate analyzing 30% Cr20 J; processing are pre-concentrated by electronic are sorting resulted in 64% recovery of chromite in a concentrate analyzing 30.5% Cr20J.IntroductionA five-year mineral development sub-agreement was signed between the federal government and the province of Manitoba in 1984. The purpose of the agreement was to establish a work program which would strengthen and diversify the mineral resource industry of Manitoba. Basically, the agreement covers three sectors: Sector A, geoscience; Sector B, mining and minerals technology research; and Sector C, development studies.Project selection involved input from industry, federal and provincial representatives. In the case of industrial mineral s, the selection was initiated at a meeting held at the offices of the Department of Mines and Energy, Winnipeg, Manitoba, in October 1985. One such project was the evaluation of the chromite ore deposits at Bird River, Manitoba."

Jan 1, 1988

By R. Pakalnis, H. Miller, Madill. T.

"This paper describes a methodical approach to the estimation of the orientation and the magnitude of in-situ stresses. The study was performed at the Ruttan Mine, Sherritt Gordon Mines Ltd. , a 6,000 T.P.D. underground operation, located in northern Manitoba, Canada. It involves an initial estimate to be made based upon: structural interpretation • virgin stress measurements conducted in other areas (world wide, regional)The verification of the prevailing stress regime was made by conducting CSIRO hollow inclusion(1) overcoring measurements. The current cost for a virgin stress determination is about $7000 per measurement(2) and the difficulty encountered in attaining a good reading is high. This paper will describe the analytical procedures employed at Ruttan in evaluating the in-situ stress magnitude and orientation based on three overcore tests. It is proposed to perform an additional six measurements in order to verify the following results:Vertical stress = av (MPa) = 0.027 by depth (m)Major principal stress = o! """" 2.5 xav (340°/-20°)*Intermediate principal stress = a2 - 1.2xav (070°/0°)Minor principal stress = a3 """" o.8xov (160°/-70°)IntroductionThe Ruttan Mine of Sherritt Gordon Mines Ltd., a 6,000 T.P.D. underground operation, is located in northern Manitoba, Canada (Fig. I). The Ruttan copper-zinc orebody is a multi-lensed, steeply dipping (70 degrees) en-echelon deposit. Individual lenses have a maximum strike length of 350 m with widths varying from 7 m to 61 m. The mining method is o pen stoping with delayed backfilling and extends from surface to 860 m below surface."

Jan 1, 1985

By S. H. Logan

The present discussions throughout the civilized world on the subject of gold for monetary purposes may seem due to general economic conditions during the past year. But for some years previously a small group of authorities had warned the world against the continued disregard of an equitable distribution of existing gold reserves, and had urged the necessity of keeping the supply of new gold equal to the monetary demand, which, according to world production and trade figures, increases on the average about 3 per cent per annum. In 1927, Sir John Aird, the President of The Canadian Bank of Commerce, stated that the United States could spare a billion dollars of the supply it then held, 4 ½ billion dollars. About a year and a half ago the Professor of Banking and Currency in the University of London, Mr. T. E. Gregory, said, "If the world finds it impossible to modify its habits so far as to make an organized effort to economize gold seem less Utopian, it must be prepared to pay for its bad habits, in this and other respects, by a possible loss of material welfare." These clear-cut statements were not heeded, perhaps for one reason because most countries were in the flush of prosperity, and making such great demands upon the mining fraternity for industrial materials as to distract attention, at least to some degree, from gold mining. Now the world knows it faces serious problems, first, of making? fully effective its present monetary reserves, which, although badly distributed, are as a whole ample for the needs of the present, and secondly, of preventing a shortage in the supply of new gold, one that may come within the next few years if the present sources of supply are not enlarged, and if there is no marked change in the technique of gold production.

Jan 1, 1931

By Minoru Fujita, Ian M. Johnson

"A helicopter-borne geophysical survey was flown in 1978 over selected areas on Kyushu Island, Japan. The principal sensors were a moving source electro-magnetic system and a magnetometer. Maps of apparent resistivity were generated from the EM data. Based on the resistivity signature of known deposits within the survey areas, targets were selected for ground follow-up. Drilling of one such target in late 1980 resulted in the discovery of a gold deposit from which full production will begin in the summer of 1985. The deposit contains a minimum 120 tonnes (3.86 million ounces) of recoverable gold and is the largest in Japanese history. The deposit is in a geological setting previously unsuspected of hosting precious metal deposits. The case history suggests a preferred exploration strategy which might be employed in other similar geological environments.IntroductionThe Hishikari area is located some forty-five kilometres north of Kagoshima city, Kagoshima Prefecture, Kyushu Island, Japan (Fig. I). The area and its environs is one with a number of gold deposits which have been worked with varying results since the late 1800s. The large st deposit in terms of recovered gold is the Ohkuchi (or Oguchi) Mine (Fig . 2) which was recently closed due to exhaustion of reserves. The Ohkuchi Mine started production in 1896. A total of 22.2 tonnes (714 ,000 ounces) of gold, with an average ore grade of 13.6 grams/tonne (0.39 ounces/ton), was extracted over the Life of the mine.In an attempt to discover new deposits , the Metal Mining Agency of Japan (MMAJ) carried out a regional geologic mapping program of the area between 1975 and 1977. This was followed by a helicopter-borne electromagnetic and magnetic survey. The airborne survey was flown by Scintrex and the compiled results presented to MMAJ in early 1979."

Jan 1, 1985

By Shantanu Patel, C. Derek Martin

"The objective of this work is to develop a practical numerical approach for applying the confining pressure to discrete element cylindrical triaxial tests. A layer of membrane particles with very low stiffness and extremely high contact bond strength was created around the lateral boundary of the cylindrical numerical specimen. To prevent the membrane particles from penetrating into the rock specimen on application of confining forces and to provide a smooth boundary surface, the space between the membrane and rock particles was filled using small-diameter packing particles. The results of this method were compared with those of rigid boundary method with confining pressure of 20MPa. The results obtained show that new approach gives both peak strength and post peak response that are in closer agreement with laboratory findings. BACKGROUNDThe discrete element method (DEM) has become the cornerstone for simulating both intact material and discrete fractures for low porosity strong rocks (ISRM Classes R3 to R6). Despite the advances in its application, simulating realistic behaviour of intact rock using the DEM remains a challenge. The bonded particle model was introduced as a potential solution for simulating the complex mineral grains in strong rock and other granular materials (Potyondy and Cundall, 2004; Utili and Nova, 2008; Salot et al., 2009). While some issues were resolved, a remaining challenge is the lack of the bonded particle model to simulate the brittle response commonly observed in strong rocks during the triaxial compressive test. Such behaviour is shown in Fig. 1 for Lac du Bonnet Granite at a confining pressure of 20MPa."

Jan 1, 2015

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama, Ryuji Oinuma

"Recently, the arsenic grade in copper ores has been increasing year by year. Arsenic bearing minerals (enargite (Cu3AsS4) and tennantite (Cu12As4S13)) coexist with typical copper minerals such as chalcopyrite (CuFeS2). The removal of arsenic from copper ores that contain relatively high arsenic content is essential due to its adverse impact on the environment and the resulting economic consequences. In this study, arsenic removal and dissolution behaviour of Cu and As from enargite (Cu3AsS4) were investigated using ferric sulphate (Fe2(SO4)3) solutions containing sodium chloride under high pressure oxidation conditions. The effects of numerous parameters including the concentration of Fe2(SO4)3 and NaCl, temperature, total pressure, leaching time and particle size were studied while other variables such as pulp density and stirring speed were fixed at 100 g/L and 750 rpm. The results showed that more than 60% of the copper was dissolved in a 0.1 M ferric sulphate solution under the high pressure oxidative conditions, whereas the leaching rate of arsenic was less than 20%. SEM observation revealed that elemental sulphur was deposited on the surface of enargite forming a passivation layer and the residue was agglomerated. Those phenomena may cause a decrease in the copper leaching rate. It was found that more than 80% of copper was dissolved in the ferric sulphate solution in the presence of 0.34 M sodium chloride under the conditions optimized, whereas the dissolution of arsenic in the mixture did not exceed 2%. XRD analysis of the solid residues from the leaching experiments used ferric sulphate and mixtures of ferric sulphate and sodium chloride showed arsenic to be present as scorodite (FeAsO4).INTRODUCTION In recent years, there has been an increase of the arsenic (As) content of copper ores due to the gradual depletion of high grade copper ores. In some copper deposits, arsenic occurs in the form of minerals such as enargite and tennantite. The removal of arsenic in ores containing copper is critical to the production of pure copper and the management of the environmental challenges caused by the smelting process. Due to the environmental risk caused by arsenic emission and the deteriorated quality of the copper product, smelting of enargite concentrates is not an effective method for the extraction of copper (Padilla et al., 2010; Safarzadeh et al., 2014; Long et al., 2012). Therefore, a number of studies have been carried out to develop arsenic removal technologies from copper ores using various methods such as hydrometallurgy (Curreli et al., 2009; Tongamp et al. 2010), pyrometallurgy (Dalewski., 1999; Padilla. et al, 2012) and bio-oxidation (Ehrlich, 1964; Sasaki et al., 2010). Several hydrometallurgical leaching processes like sulphuric acid, alkaline sodium sulphide and sodium sulphate and ferric sulphate leaching have been developed to treat enargite ores and concentrates. The alkaline sodium sulphide leaching process has been developed for the removal of arsenic from enargite (Anderson, & Twidwell, 2008; Parada et al., 2014). The mechanism of the dissolution of arsenic from enargite in sodium sulphite solution is"

Jan 1, 2016

By Nosa O. Egiebor, Kafui Nyavor

"The effectiveness of sulphuric acid, nitric acid, and hydrogen peroxide pressure oxidation on the cyanide extractability of gold from a double-refractory concentrate is presented. Whileover90% of the sulphide content could be oxidized by either of the two acid pretreatments, only 65% was achieved by the peroxide oxidation. Carbon oxidation by both acid and peroxide pressure oxidation were less than 15%. Although the peroxide pressure oxidation pretreatment resulted in much lower sulphur and carbon oxidation, it gave pretreated residues with decreased levels of preg-robbing activities and higher gold recoveries during subsequent cyanidation, thus indicating some deactivation ofthe preg-robbing carbon during pretreatment with hydrogen peroxide. The refractoriness due to carbon preg-robbing activity was found to contribute more to the refractory behaviour of the concentrate than the occlusion of gold particles by the sulphide mineralization.IntroductionGold ores and concentrates are classified as refractory when a significant portion of the gold content cannot be extracted efficiently by conventional cyanidation, even after fme grinding (Weir and Berezowsky, 1984); (Demopoulos and Papangelakis, 1987). The refractory behaviour of precious metal ores and concentrates is generally attributed to two main factors: The presence of carbonaceous materials which could cause preg-robbing activity during cyanidation (Zaitseva et al., 1973); (Nice, 1971); Scheiner et al., 1971); (Eisele et al., 1983), or occlude gold-bearing minerals (Wells and Mullens, 1973); (Gasparrini, 1983); (Chen and Reddby, 1990), and the occurrence of sulphide minerals which can occlude gold, thus reducing the access of lixiviants (Schwartz, 1944); (Weir et al., 1986); (papangelakis and Demopoulos, 1990); (Michaelis, 1989); (Schweigart, 1965). When the refractoriness is due to a combination of these two factors, the ore or concentrate can be referred to as being ""double-refractory"". Because of the rarity of gold ores exhibiting this double-refractory phenomenon, only a few studies have been carried out on their suitability for pretreatment by existing techniques."

Jan 1, 1992

By R. L. Guerguerian, Eugene Bercel

"Grinding mill hydrostatic trunnion bearings require an external pumping source to provide and maintain the oil film between the bearing members. In order to guarantee a predetermined minimum film thickness, the lubrication system tends to be oversized. The oil film is ""indirectly"" controlled by flow, pressure and temperature monitors with fixed settings on the conservative side. This can lead to excessive maintenance and abbreviated life for the lubrication system components. A reliable method of monitoring actual film thickness would not only provide greater mill availability, but also minimize maintenance costs.This paper describes the instrumentation installed in Dominion hydrostatic bearings, and presents results of field tests where the output of that instrumentation was recorded under various operating conditions.IntroductionThe trend toward larger and more sophisticated grinding mills has made the operators of these machines increasingly vulnerable to financial loss, as the cost of downtime and repairs has increased directly with machine size. In order to guard against such losses, it is becoming imperative that large, sophisticated grinding mills be equipped with protective instrumentation to monitor some of the critical operating parameters and to identify events and trends which, if they go unnoticed, can lead to excessive maintenance costs and machine downtime. The idea of protective monitoring systems is not new. The operators of certain types of machinery where a high degree of safety is required or where machinery health can deteriorate very rapidly, as in the case of high-speed turbo-machinery, have long been using protective instrumentation on their machines. The increased awareness of the benefits of monitoring machinery conditions and the availability of reliable and relatively low-cost instrumentation of a large range of sophistication is making the practice now widespread. Traditionally, grinding mills have not been considered as high-risk machinery requiring instrumented protection. However, the trend, mentioned earlier, toward employing fewer, but larger capacity, mills increases the risk of significant disruption of production, and therefore measures to minimize the risks are desirable."

Jan 1, 1981

By A. J. Hyett, R. D. Reichert

"A laboratory and field research program was conducted to investigate the major factors influencing bond capacity of grouted cable bolts. The results indicate that cable bolt capacity most critically depends on the grout uniaxial compressive strength (UCS), the radial confinement, and the embedment length.In the laboratory &apos;split-pipe&apos; tests were conducted using P VC, aluminum and steel pipes to provide radial confinement, and field test sites were chosen in granite, limestone and shale rock masses. For both datasets higher capacities were obtained under conditions of higher radial confinement. A correlation between the two was obtained through a comparison of the radial wall stiffness of the laboratory pipes with that of the field boreholes as measured using a high pressure dilatometer. Cable bolt capacity was found to increase with embedment length though not in direct proportionality.The use of low water cement ratio grouts (<0.40) can increase cable bolt capacities by 50% to 75%. This effect is maximized under conditions of high radial confinement. However, the use of super thick grout paste (0.30 and less) may be both impractical and undesirable, first because of their limited pumpability and second because of their inconsistency in strength. Grouts with a water cement ratio of between 0.35 and 0.40 are recommended for practical cable bolt applications."

Jan 1, 1992