Search Documents

By G. M. Scamans

In the past ten years there has been considerable penetration of aluminum automotive body sheet (ABS) into automotive structures. The exponential increase in demand is resulting in major investments in heat treatment and finishing capacity across the globe. Line speed and tonnage throughput is limited by the continuous heat treatment (CHT) floater furnace rather than the cleaning and pretreatment section where electrolytic treatments that offer higher line speeds should come into favour and roll coating of pretreatment should predominate. The capacity limiting surface texturing pass will either be eliminated or moved to the finishing line or a dedicated mill. The key to making aluminum both embedded carbon and cost competitive with steel for more and more affordable classes of vehicles lies in recycling of both prompt scrap and, in the longer term, end of life vehicle scrap. For the first time scrap separation technology is available that can compete effectively with hand sorting and can sort aluminum shredded vehicle scrap into wrought and cast alloys and then into individual alloy groups. The challenge is to use more end of life scrap in alloy formulation whilst at the same time extending the property range in terms of both strength and formability.

Jan 1, 2015

"INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of the city of Timmins, Ontario. Two types of ore are treated; 'A' type, a copper-zinc-low silver ore producing copper and zinc concentrates, and 'C' type, a copper-lead-zinc-high silver ore producing copper, lead and zinc concentrates.The ore is processed at a combined rate of 12,400 metric tonnes per day through four parallel grinding and flotation divisions. Three divisions treat the 'A' type ore and the fourth treats the 'C' ore. Each division is fed from its own fine ore bin.This paper reviews the grinding section with specific emphasis on grinding media consumption and the factors affecting it as related to 'A' type ore. At Kidd Creek there was an awareness that grinding media consumption varied on a weekly and monthly basis. The reasons for this variation was usually attributed to ore hardness as evidenced by short term variations in the circuit feedrate and head assays. However, there has been a diversity of opinion published in recent years regarding the factors contributing to steel consumption. This initiated a study of historical Kidd Creek operating data, from the period 1970 to 1986 inclusive, to determine the effect of various operating parameters on media consumption. The results of the study could then be used as a baseline for future media consumption testwork."

Jan 1, 1988

By B Lumsden, B Lacouture

"Red Dog is one of the largest zinc mines in the world both in terms of reserves and annual production. In 2013, Red Dog produced 551,300 mt of contained zinc and 96,700 mt of contained lead. The mine, which is located in Northwest Alaska, is a partnership between Teck Alaska Incorporated, the operator of the mine and NANA Regional Corporation Inc, the local land owner. The Aqqaluk deposit, which is the current source of ore, has an average grade of 15.8% Zn, 4.1% Pb and 73 g/t Ag with the main minerals being sphalerite, galena, pyrite, barite and quartz. Surveys of the zinc flotation circuit at Red Dog identified that a substantial amount of fully liberated, sub 20 micron sphalerite particles were being lost to final tailings. As a means of improving fine sphalerite recovery, a four month plant trial of magnetic conditioning was conducted in the zinc retreat circuit. Magnetic conditioning technology has already been commissioned in several concentrators around the world to agglomerate fine paramagnetic minerals, increasing their probability of bubble collision and recovery in a flotation cell. The results of the four month plant trial at Red Dog showed that at a high level of confidence, a 1% increase in zinc recovery or zinc recovery and zinc concentrate grade combined was achieved with magnetic conditioning. The resulting economic benefit, which is also at a high level of confidence, is significant to Red Dog and therefore, magnetic conditioning has been permanently incorporated into the Red Dog zinc flotation circuit.IntroductionRed Dog is the largest zinc mine in North America and represents approximately 29% of North American zinc concentrate production. The mine is located in northwest Alaska, approximately 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The remote location makes the mine accessible only by air or seasonally by ocean-going barges. Red Dog is a partnership between NANA Regional Corporation Inc, the land owner and Teck Alaska Incorporated, the operator of the mine."

Jan 1, 2016

By Eric Bain Wasmund, Lance Christodoulou, Julio Jairo Carmona Franco, María Fernanda Castillo, Jose Concha

"A number of technologies are in practice for selectively removing coarse gold from conventional grinding circuits. These circuits are often designed so that the grinding mill output is size classified, with large (or high density) particles being removed before the tails are returned to the mill. Because of the high relative SG of gold, and the fact that some forms of gold such as free gold do not break apart during conventional grinding, coarse gold can accumulate in the circulating load, and eventually be lost.Eriez has developed a flotation cell that uses fluidized water to enhance flotation of coarse particles. More than 40 units have been sold in industrial minerals, and we are now exploring applications for the HydroFloat® in the gold industry.Mineros S.A currently produces approximately 120,000 oz of gold per year by gravity concentrating alluvial gold ore with a mean particle size of 330 microns, followed by further concentration using a Falcon separator. A 400 mm diameter pilot-scale HydroFloat® was added to the tails of the Falcon to test whether additional gold could be captured. Enrichments of 50-600 times and recoveries normally in excess of 95% were achieved. This allowed direct smelting of the gold concentrate. Metallurgical results and operating parameters such as water addition and power will be discussed during the presentation.This result opens the possibility that the HydroFloat® could be used directly in the grinding circuit, for removing coarse gold in the circulating load. This work also shows the possibility that the HydroFloat® can produce a throwaway tail, which will reduce the size of the circulating load stream and the grinding requirements of the circuit."

Jan 1, 2015

By H. A. Bilgin, G. G. U. Aldas

"Ground vibration is the natural result of the blasting process. Many empirical formulae and methodologies including analysis of travel path effects have been developed. The scaled distance, which is the most popular approach for the calculation of the attenuation of particle velocity in the ground, has led to significant advances in the prediction of particle velocity when both explosive charge and distance vary. However, this approach does not consider the effect of ground anisotropy and existence of structural geological features on ground vibration. Therefore, in this study, the effects of these rock mass properties on types, amplitudes, and frequencies of ground vibration waves at four surface mines are examined. The results, which were implemented at Kangal coal mine, Bastas quarry and Kíbrís quarry, provided guidance for the extensive study at Orhaneli surface coal mine.As a result of the study, the authors came to the conclusion that vibration amplitudes change depending on the ground on which sensors were deployed and the conditions depending on whether measurements were done near major structural geological features. It was determined that the vibration amplitudes, measured at equal distances from the source but in different directions, change because of the propagation velocity anisotropy. Besides the change of wave type due to the kind of ground at the measurement location, it was determined that vibration anomolies were due to structural features."

Jan 1, 2004

By S. Tuttle, R. Sisson

"Suncor Energy Inc. has proposed a 2.2 billion dollar expansion to the current oil sands operation, which will more than double the productive capability of the facility. As part of the application for this expansion, a comprehensive closure plan had to be developed and filed.Closure planning includes a systematic evaluation of the area to be developed, the development activities planned, the goals and objectives of the corporation in re-establishing landforms and ecosystems at the same time as running an effective operation. As early as is practical during the mine development, surface contouring is completed, soil is reconstructed, and vegetation, surface drainage and wetlands are re-established. Once active reclamation is complete and vegetation has been re-established, Suncor monitors maturation of landscapes and ecosystems to provide the submission basis for reclamation certification"

Jan 1, 1999

By Gus Van Weert, Peter Kondos

"Ore sorting has been quite successful in providing a separation means in the rock size range of 1 to 6 inches; a range where mineral dressers do not have many options. The industrial minerals and recycling worlds have embraced this technology. However, ore sorting has not found wide application in the base or precious metals mining industry. One reason for this is thought to be the reliance of most sensors on rock surface characteristics, not very useful in case of sulphides, non-existing in case of gold. Microwave heating, however, is specific for sulphides and graphite (or carbonaceous matter) embedded in the rocks; washing or even drying does not appear necessary. Separation can be done afterwards by already existing ore sorting technology using infrared sensors. Test results on six Nevada gold ore samples are presented in detail. Some simple test procedures are also presented for those wishing to explore the microwave potential of sulphide sorting in their own operations.INTRODUCTIONMineral processing in the base metals industry most often involves upgrading of the ore, concentrating the valuable mineral fraction by classic methods, such as flotation. Since the liberation of minerals in the ore occurs mostly at or below the 100 micron level, the industry has been living with fault lines, so to speak, between blast hole spacing (10,000 mm), run-of-mine ore size (100 mm) and beneficiation size (0.1 – 0.01 mm). The acceptance of ore sorting will inevitably lead to the revisiting of the following questions: “Exactly how much below ore grade rock ends up in the mill because the geologists or the miners cannot define the resource boundaries more precisely? How can the economics of dilution be improved? How many ore grade rocks are lost with the overburden?”"

Jan 1, 2007

By J. C. Escobedo, J. M. Almanza, A. Flores, Cortés. D. A.

Secondary aluminum dross, which has been exposed for several years to atmospheric conditions, was characterized using chemical analysis, X-ray diffraction, optical and scanning electronic microscopy, and energy-dispersive spectroscopy. Based on the characterization, a method to purify the solids is presented. This method starts with the washing of the dross in boiling water to eliminate the soluble compounds like Na and K, followed by the physical separation of the metallic aluminum by milling and screening. Finally, an acid lixiviation process is applied using three different acid solutions, HCl, HNO3, and H2SO4. The best results were obtained using HCl. The main insoluble components of the dross after lixiviation were Al, SiO2, and Al2O3. MgAl2O4, AlN, Si, and Na2Al22O3·2H20 species were also found. Based on the alumina content, the solid product could be suitable as a raw material in the manufacture of castable refractories or metal matrix composites.

Jan 1, 2005

By Larry A. Lien

"A brief summary of the different membrane separation options currently available to the mining industry will be presented and discussed. The processes described involve operating membrane plants on the following applications: pregnant leach solutions (PLS) in the copper and gold industries, fractionation and concentration of metals and acids in refineries, and wastewater treatments to meet state-of-the-art surface discharge criteria.Included is a specific discussion on cost savings resulting from an operating membrane treatment system of nearly 3,500 m3/hr barren water relative to the prior, conventional precipitation practice at a major heap leach gold mine. This Engineered Membrane Separation® (EMS®) plant has produced water for six years that has met all standards for direct discharge into the environment, and captures and returns to the operation valuable minerals and solvents which were not previously being extracted in the Merrill-Crowe process.INTRODUCTIONMembrane technology has been available for more than 35 years, but has been used sparingly in the mining industry. However, recent developments in polymer chemistry, spiral-wound element design and construction, water clarification pretreatment equipment and techniques, and an expanded understanding of membrane fouling and cleaning techniques have dramatically improved the reliability and robustness of membrane-based systems for potential use by the mining industry.In the past 15 years large operating plants have successfully demonstrated the use of this “new” membrane technology to include the separation of pay-metals from large-volume acid and cyanide heap leach mining solutions containing copper, zinc, gold and silver. Moreover, variations on these same membrane technologies are ideally suited to fractionations that add value to processing fluids from refineries, like separating metals from acids or concentrating acids and producing high-quality process fluids."

Jan 1, 2010

By D. M. Wyslouzil

"This paper was prepared for presentation at the 16th Canadian Mineral Processor's Annual Meeting, Ottawa, Ontario, Jan. 17 to Jan. 19, 1984.This paper gives an account of the development of treatment procedures for the differential flotation of refractory copper-zinc ores. Special references are made to the effectiveness of various zinc depressants and their combinations.Studies carried out on refractory copper-zinc ores demonstrated that conventional zinc depressants such as cyanide and zinc sulphate were not particularly effective when secondary copper minerals were present in the ore; the flotation activity of sphalerite was enhanced in the presence of cyanide.Among the various zinc depressants evaluated, the following depressant combinations were found most effective: Zn(OH) 2-S02 , 802-CaO, Na2S-Na2S03-S02, Na 2 S-S02 and Na 2S-S0rDS22.The practical application of any of these systems depends on the type of ore treated and other conditions such as pH, levels and points of collector and depressant additions.In this paper the effect of each depressant combination on different ores is described with reference to the selection of collectors."

Jan 1, 1984

By U. Storck

"Shaft sinking for exploitation of the deep potash beds in Saskatchewan involved great difficulties from the very first because of the need to exclude from the shaft the high-pressure water encountered in the overburden. Control of the troublesome Blairmore quicksands was achieved relatively quickly by use of the freezing method and by lining with cast iron tubbing. The unsolved problem remained, however, of sealing the water-bearing Devonian where the formations had extremely low permeability and were thus hard to grout. Long experience in German potash mines had shown that the permanency of the whole mine would be seriously endangered if large amounts of unsaturated salt water were allowed to flow in from the shaft wall and merely removed by pumping. The prevention of water movement and the resulting dissolution of salt in the overburden were known to be most important. In the Alwinsal shaft, water flow from the Devonian has been prevented by the use of a steel and concrete sandwich lining similar in principle to a kind of lining introduced a few years earlier, and for another reason, in German coal shafts. As its installation is neither more expensive nor more time consuming than that of cast iron tubbing lining, this same lining was also chosen as protection against the Blairmore quicksands. The great advantage of the steel lining, in addition to its relatively high strength, is the fact that it is possible to make the joints of the individual segments absolutely and permanently water-tight by means of tested welds. The virtual dryness of the Alwinsal shaft will also result in lower costs because significant corrosion of all its steel installations, including skips, cage and ropes, will be prevented."

Jan 1, 1968

By V. J. Sopuck, O. P. Lavin, Ian Nichol

"A major challenge of contemporary exploration geochemistry is the development of procedures that can locate blind mineralization or mineralization that sub-crops below a cover of transported overburden, the composition of which bears no relation to the underlying mineralization. Over the past few years, the possible existence of diagnostic geochemical features in the country rock associated with volcanogenic massive sulphide deposits has attracted increasing attention both on the local mine scale and on the regional scale. In the present investigation, the nature of the geochemistry of a number of Archean greenstone belts of the Canadian Shield is examined to determine the feasibility of distinguishing productive from non-productive areas of copper-zinc mineralization. The results indicate that productive areas are distinguishable from non-productive areas providing consideration is given to the effects of igneous differentiation on rock compositionIntroductionArchean massive sulphide deposits are an important source of copper and zinc, and to a lesser extent silver and gold, particularly in Canada. As in the case of most other forms of mineralization, there is a continual need to develop new techniques that will improve the chances of success in the search for these deposits. The majority of Archean areas in the northern latitudes are overlain by a variable cover of glacial overburden. Considerable progress has been made in the development of new geochemical exploration techniques for use in glaciated terrain, based on the detection of anomalous dispersion in the glacial overburden. In certain situations, however, as in the search for blind deposits or in areas covered by glaciolacustrine deposits, overburden geochemistry offers little hope for success. In the case of massive sulphide deposits, one possible solution may lie in the detection of anomalous geochemical signatures in the bedrock. Recognizing this possibility, attention has been directed to the investigation of the nature of lithogeochemical dispersion associated with massive sulphide deposits on both regional and local scales, to establish the potential of lithogeochemistry as an aid in the search for these deposits."

Jan 1, 1980

By C. Cornejo, C. Schuffeneger, J. Rosas

"At the end of 2010 the AMSA Esperanza Concentrator started commissioning. Located in the Atacama Desert this project is the first of several large size concentrators developed recently to operate in Northern Chile. In addition to the new operations to be implemented in the short term, many existing installations are planning expansions. The use of large size equipment is one of the common characteristics of the new concentrators, but also new technologies are being considered and innovation is present in most cases. Sea water or desalinated water will be required to process large tonnages of sulphide copper ores as well as gold bearing ores, since process water supply from the Andes will no longer be available. The high cost of sea water or desalinated water supply and the high cost of energy are not a limitation as the current metal market scenario allows obtaining an attractive NPV even from installations designed to process relatively low grade ores. A review of the current concentrators being developed in Chile is presented, including a description of the main design issues related to technology and innovation. An analysis of the Chilean mining industry is also presented, detailing mine and plant capacities as well as expected final products.INTRODUCTION The mining sector in Chile has become a reference when analysing the large concentrator plants projected or currently in operation all over the world. At present and as a consequence of the high price of metal commodities, most South American countries have an active mining sector. Chile is known as a major producer of metals. First records of copper production exported to Spain are dated to the early XVII century. Since then Chile has produced over 13% of the total copper ever produced in the world. After 1990 Chilean mining and the associated cluster of activities has substantially grown to levels never reached before, especially in the production of copper, gold and other non-metallic minerals. This dramatic increase is the result of an economic policy based on delivering comparative advantages and incentives for the admission of foreign capital to offset the weak domestic investment in previous decades. Massive mining of its huge mineral resources has allowed Chile to be a world leader in the production of copper and other base metals and mineral products."

Jan 1, 2012

By E. V. Neelands

THE Canadian Malartic mine is in Western Quebec, about fifty miles east of Noranda and forty miles south of Amos on the Canadian National railway. The recently constructed branch of the railway from Rouyn to Senneterre passes half a mile north of the mine. HISTORY he property was discovered in 1923 'by St. Barbe Sladen, H. S. Kennedy, and J. C. Carroll, who were prospecting for an Ottawa syndicate and found gold in a small quartz vein near the present workings. Five claims were staked and were optioned to an exploration company, who allowed the option to lapse after surface sampling and diamond drilling eighteen holes. Some months later, the property was sold to Malartic Gold Mines, Limited, who carried on development until 1929. A vertical shaft was sunk and exploration work done on three levels, supplemented by diamond drilling 16 surface holes and 62 underground holes. The work indicated that the important ore occurred in two silicified.zones in schisted greywacke which intersected west of the shaft and were believed to be controlled by a drag-fold. The ore grade was not considered sufficiently favourable to war-rant an operation, and work was terminated. With the advance in the price of gold to $35 per ounce, interest was revived and a new Company, Canadian Malartic Gold Mines, Limited, was incorporated for further development. The shareholders of the old Company accepted a new position under which their interests were protected, and sufficient treasury shares were optioned to Ventures, Limited, and Sudbury Basin Mines, Limited, to provide funds for further exploration of the prop-erty to determine whether, under the new economic conditions, profitable operation would be possible, and, if advisable, to provide the equipment for production. Additional claims were acquired, bringing the total area up to 1,029 acres.

Jan 1, 1939

By R. Barbaroux, B. Dubreuil, D. Lemieux, K. Nasrallah, G. Garcia Curiel

"As conventional, base or precious metal ores are being depleted worldwide, the mining industry is being faced with an increasing exploitation of arsenical sulfidic ores. Enargite is a common example. The downstream processing of these ores poses several problems ranging from high smelter penalties to finding economical and environmentally acceptable means of disposing of the arsenic. Several hydrometallurgical processes have been proposed for extracting arsenic from enargite concentrates, notably using alkaline sulphide leaching (ASL). However, few alternatives exist for removing the arsenic from solution and stabilizing it in an approach that is both economical and environmentally acceptable.Dundee Sustainable Technologies (“DST”) has developed a technology for the sequestration of arsenic by vitrification. Originally optimized to cost-effectively stabilize arsenic trioxide (As2O3), DST has shown that vitrification could be successfully extended to the stabilization of other arsenical products, such as calcium arsenate (Ca3(AsO4)2) and sodium arsenate (Na3AsO4). In this paper, the vitrification of arsenic in the context of an enargite leaching was newly explored and demonstrated successfully.Two processing routes are being proposed by DST for the removal of arsenic from enargite concentrates and their stabilization by vitrification. In one route, arsenic is extracted by ASL and is then precipitated under atmospheric conditions and with minimal use of reagents and time. The resulting precipitate is an unstable hydrated ferric arsenate (FeAsO4•2H2O) that is then vitrified in a non-dilutive method, significantly increasing the stability of arsenic and meeting the TCLP guideline. Unlike is required for scorodite, stabilization was successfully achieved without concern for the crystallinity of the precipitate."

Jan 1, 2017

"WELCOME/BIENVENUE TO THE COM 2014 IN BEAUTIFUL VANCOUVER!On behalf of the organizing committee, I would like to extend my thanks to you for participating in this year’s Conference of Metallurgists. Recent times have been extremely difficult for the resource sector, but it is crucial for our industry to maintain personal connections through good and bad times. These interactions include technical exchanges, and this is at the heart of MetSoc’s service to its members. The theme of this 53rd Conference of Metallurgists is Prosperity Through Process Advancements. There are thirteen symposia at this year’s conference mainly focused on processing from extractive fields, to materials and the environment. Supporting these topics are the plenary, poster session, and trade show plus opportunities for socializing at functions like the opening reception and the awards banquet.Many people have contributed to this conference, from the authors and presenters to the organizers and the generous sponsors. They are all gratefully acknowledged for their quality work over the last two years. A particular thank you to our student volunteers whom we hope will take advantage of their time at COM to network and to learn about this exciting industry.Again, thank you for being a part of this exciting conference of metallurgists. I hope it will be a memorable experience and that you are able to take advantage of all the conference and Vancouver have to offer."

Jan 1, 2014

By J. Lee, R. G. Rosehart

"The basic problem of arsenic contamination from mine water is discussed. Effective methods of removal involving chemical precipitation, activated carbon adsorption, ion exchange and reverse osmosis are discussed. As well as an economic analysis, detail is also paid to other ions in solution which are removed simultaneously.INTRODUCTIONThe object of this paper is to review arsenic and its removal from gold extraction plant effluents. The first method considered is chemical precipitation. A second method is sorption processes, such as ion exchange resins and activated carbon adsorption. A third method is the possible application of reverse osmosis for the treatment of mine waste waters containing arsenic.Arsenic pollution in the gold mining communities of Canada and Ghana have been extensively studies (l, 2). Lynch(3) Shabunin, Gutman and Kogan( 4), Hollo, Troth, Vennes and Illinigi (5) and Hau(6) have reported their removal methods of arsenic by chemical precipitation, ion exchange and biological methods. Their conclusions were that the precipitation with Fe2+ and Fe3+ ions was most effective.Scope of the ProblemInitial aspects of this research program involved a detailed analysis of the operation of a gold extraction plant located in Canada. The name and location of the mine is proprietary information. Figure 1 gives a basic process schematic with the main tailing streams identified.Table 1 gives information as to the various mine streams and their physical and chemical composition. In this study, primary attention is paid to the removal of dissolved arsenic from waste waters. Solids from this type of operation can always be back-filled. As could be anticipated, the dissolved As content of the primary flotation tailing stream is very low. The dissolved As level in the secondary processing stream and the roasting quench water is quite high. The reason being that at this stage of the process, the arsenic has been freed from the arsenopyrite forms."

Jan 1, 1972

By G. Lyle

Since its inception CEMI (Centre for Excellence in Mining Innovation) has focused on facilitating innovative solutions to the mining industry in six strategic research areas; GeoRisk, ConstructMine, ValueMine, FindMine, SustainMine and MineTech (visit www.miningexcellence.ca for details). This paper focuses on CEMI?s largest project to date, Ventilation on Demand (VOD). Energy consumption in mines can account for upwards of 40% of a mines operating cost, with a significant portion of this been consumed by the ventilation requirements. VOD provides a significant opportunity to reduce overall mine ventilation requirements and subsequently energy costs, while potentially increasing mine productivity. CEMI is currently in year 2 of an assessment of VOD, focusing on the financial, physical and equipment viability of utilizing such systems in both new and existing mines. This two year program, to be completed by March 31, 2011, is designed to systematically assess such a system to determine if and when it could effectively be applied in underground mines. The paper will describe the process by which the project was initiated, the demonstration projects established to capture data, the means to interpret the data and the modelling developed to calibrate and predict ventilation system requirements.

Oct 1, 2010

By Patrick F. R. Murphy

The mechanization of platinum group metal (PGM) underground reef mining in South Africa has posed a challenge to mining engineers for several decades. This is primarily due to the shallow dip angles and narrow thickness (<1.1m) of the tabular orebodies mined, and the issues faced in developing reliable drilling, bolting and loading machines suitable for such hard-rock mining applications. Presently, mining is typically conducted using hand drills and scraper shovels. These methods, however, are intensive in terms of manual labor, and limited in terms of productivity, and improved methods are desired. This paper will review the technical features of a 4 tonne, low-profile, LHD for narrow-reef PGM mining, developed by EJC Loaders Division.

May 1, 2003

By Maya Kamenetsky, Khoi Nguyen, Natalee Bonnici, Steve Walters, Claire McMahon, Julie Hunt, Ron Berry

"The analysis of meso- and micro-scale textural attributes has been undertaken on ore samples from the Ernest Henry iron oxide-copper-gold (IOCG) deposit in NW QLD. Quantified textural data including grain size, shape and mineral association have been extracted from classified images of core with the aim to better predict potential mineral processing behaviours such as comminution, liberation and flotation. Data have been extracted from images of intact core at meso- and micro-scales using high resolution continuous images collected using automated core-logger technology, SEM-based and optical microscopy platforms.The results of this study will show examples of quantified size, shape and mineral association data from meso- and micro-scale classified images. Analysis of the data shows that there are domains of variable grain size and mineral association that can potentially be related to crushing and liberation behaviour. The trends that are observed at the drill-core (meso-) scale are consistent with those at the micro-scale. The results from the micro-scale analysis show that the domains defined at the core-scale have clearly different chalcopyrite sizes and shapes as well as variable bulk mineralogy.INTRODUCTIONInnovations in technology have allowed automated extraction of information about mineral shape, grain size and mineral association, i.e., texture, from meso- and micro-scale images of intact rocks. The overall aim of this research is to investigate trends in quantified textural data that can potentially give an early view of processing parameters such as predicted grind size and liberation behaviour."

Jan 1, 2009