Search Documents

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By N. Dobrin, R. Sheinman, Y. V. Kokotov, L. N. Braginsky

Increasing the production of a Mixer-Settler unit requires either increasing flow rates or increasing extractant concentration. The mixers still have to ensure complete emulsification and to maintain high values of specific interface surface area in order to provide a high rate of mass transfer. Theoretically, an increase in mixing intensity can support increased flow rates without reducing extraction efficiency. Unfortunately, conventional pump mixers and mixing systems create small droplets that do not separate easily. As pumping action and mixing intensities are increased, the quantity of small droplets increases. We describe the development and industrial application of a novel mixing system for efficient mass transfer without forming significant quantities of small droplets, targeting both high mass transfer rate and low entrainment values.

Jan 1, 2014

By J. K. Gowans

The Research and Design group of the Project Development Division (PDD) of Placer Dome Inc. includes metallurgical, electrical, civil and mechanical engineers. They provide metallurgical research and conceptual flowsheet development, feasibility concepts for the processing and ancillary facilities, and manage the detailed design of the facilities once approval has been given to a mining project. This paper describes how this group works, within the Project Development Division, to help develop feasibility studies with the Evaluations Group, manage detailed design, and provide support for the Construction Group. The paper briefly reviews the history and growth of the group and describes how it is evolving. The role of outside engineering firms and how they are incorporated into the division’s objectives are also discussed. The paper highlights the differences between Placer Dome’s Project Development Division and other mining groups, and why this approach fits the way Placer Dome does business.

Jan 1, 1998

By G. D. Mcdowell, L. B. Cochrane, B. D. Thompson

"Abstract - Exploration for deep underground copper and nickel sulfide deposits in the Sudbury mining camp is carried out with surface drilling. More detailed drilling, with an advanced underground exploration program, may be necessary to establish an accurate interpretation of the deposit geology and upgrade the resource estimate to the measured category for reserve estimation and feasibility assessment. Resource evaluation is a lengthy and costly process that could result in a decision not to proceed with the project. For projects that proceed to production, significant reductions in the operating and capital costs could be achieved with a more accurate interpretative model of the deposit geology and mineralization. Quality control procedures to ensure the integrity of the drilling data and interpretation guidelines are essential steps in the development of a deposit model. The use of block modeling techniques and the application of geostatistics for resource estimation further improve the quality of the resource model.Significant improvements to the interpretive models can also be achieved by incorporating additional information from geophysical measurements to validate and constrain the geological interpretation. The geophysical models must be consistent with known geological environments and oreforming processes, which has required the concurrent development of comparative models from exploited deposits. These geophysical techniques can also provide key geotechnical information required for the optimum design of the mining method and mining sequence. The objective of this program is to improve the accuracy of the deposit model and the quality of the resource and reserve estimates in order to optimize capital investments and reduce the development and operating costs of underground mining projects. Several of these techniques are currently being tested at INCO Limited’s Sudbury operations. The results from those tests are presented and their applications are discussed within the framework of resource/reserve classification systems and project evaluation objectives."

Jan 1, 1998

By R. S. McCaffrey

In addition to its importance in agricultural production, Wisconsin is a very large manufacturing state and its rank in the metal working industries is probably first among the States of the Union per unit of population. The University of Wisconsin is a state supported institution and the Wisconsin tradition has always emphasized the relation of the University to the state and its responsibility to exercise its leader-ship where it might, in any and every way, for the development and benefit of the state and the community. The Department of Metallurgy of the University realized its responsibilities in the carrying out of the co-operative tradition and, two' years ago, an experiment was started in co-operative research between the University and certain of the industrial plants of the state. At the present time this work has so far progressed that it is no longer an experiment, and its results prove that this co-operative research may be carried on very advantageously and that, under the conditions existing in the state, the method employed has been satisfactory.

Jan 1, 1926

By D. W. Duncan, A. Bruynesteyn

Acidic mine waters containing solubilized uranium have been observed in many uranium and some copper mines. In every case, the sulphide and iron oxidizing bacterium, Thiobacillus ferrooxidans, was also present. This bacterium provides the ferric iron required to oxidize u+4, both by oxidizing available ferrous iron and by oxidizing pyrite or other available sulphide minerals. This latter oxidation also provides sulphuric acid and may increase extraction by exposing more uranium. The enhancement of bacterial activity and the results of some field tests are discussed.

Jan 1, 1971

By Vahid Faghihi

SatraPM is a web-based software package, aiming to help project managers to easily handle their construction projects via internet. This software is capable of handling all projects of an organization, in which all projects can be defined in EPS the same as users in OBS. A 3D accessing module links EPS, OBS and inherent functions in order to provide a secure environment for the data to be processed throughout the system. This paper intends to take a deeper look at capabilities of SatraPM in helping project managers to keep track of and control their construction projects as well as its potential future features.

Aug 1, 2013

By J. Stumper

The control of the distribution and movement of liquid water is crucial for increased reliability and durability of PEM fuel cells: whereas the proton exchange membrane requires a minimum amount of liquid water for optimum operation, water excess in the GDL will impede reactant gas access to the catalyst layer thereby reducing performance. In order to understand the relationships between water management on one hand and fuel cell performance and durability on the other, Ballard has been developing a number of minimally invasive techniques that can throw light on the role of liquid water for both cell performance and durability. This paper introduces a novel measurement method that can provide information about the amount and distribution of liquid water under operation. It is shown how the MEA Resistance and Electrode Diffusivity (MRED) method can be used to determine i) the amount of liquid water in the fuel cell, ii) the pure ohmic cell resistance and iii) the O2 -diffusivity of the cathode. Furthermore, through a combination of the MRED method with current mapping it is possible to determine spatially resolved MEA resistance profiles.

Jan 1, 2005

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By J. Keough

During industrial electrowinning of copper, uneven growth can impact current efficiency, cause short-circuits in the cell and negatively impact the final quality of the metal product. Copper electrodeposits can be made smoother by incorporating a host of additives in the electrolyte but uneven copper growth may still occur due to variations in electrolyte composition throughout the cell-house. To quantify roughness, 3D images of the surface may be combined with scaling analysis to gain further insight into the deposit structure. Moreover, scaling analysis may offer a method to predict long-term deposit structure using short-term copper deposits. In this paper, the application of Atomic Force Microscopy (AFM) and scaling analysis are used to monitor copper growth and extract surface roughness characteristics. The cathode was a 304 stainless steel disc that was polished to a mirror finish. Copper was deposited onto this surface over a range of 10, 20 and 30 minutes from an acidic sulfate solution (40 g/L Cu) at 40oC from an electrolyte that contained or was free of guar. AFM images were acquired to obtain 3D topographical information on the samples and scaling analysis was performed to extract the root-mean-squared (rms) roughness, periodicity (grain size), aspect ratio of surface features and growth mechanism. INTRODUCTION During the process of copper electrowinning, the dissolved metal ions are reduced and thereby deposited onto a cathode substrate which is later recovered by stripping the metal from the cathode surface. Although this process is widely used in the industry, the conditions of the deposition procedure may cause the growth of the metal product to be uneven which can not only impact the current efficiency and final copper product quality but may also lead to plant interruptions through short-circuits if the anode and cathode make contact. To create more uniform copper deposits, a host of additives may be included in the electrolyte which may act as brighteners, leveling agents and inhibitors which may include guar gum, glue, thiourea or polysaccharides or polyacrylamides and their industrial use has changed over time (Moats, Luyima, & Cui, 2015). As such, the electrolyte composition is often complex and subtle variations in the solution matrix throughout the cell-house may impact the surface morphology of the final copper product. In an effort to quantify the roughness of copper samples, image analysis is often applied and may include Scanning Electron Microscopy (SEM) or Atomic Force Microscopy characterization. While both are appropriate, AFM offers 3-dimensional information which may be used to both qualitatively and quantitatively characterize the surface characteristics.

Jan 1, 2019

By W. G. Wahl

The Slave Province, a segment of Archean continental crust, migrated west and north from the northern flank of the Superior protoshield shortly after the Kenoran orogeny. The probable cause of migration, the path it followed and the cause of its coming to rest can be inferred from the Bouguer gravity data. The migration caused an indentation in the edge of the Superior protoshield which precluded the development of the Hudsonian orogenic front under Hudson Bay. As the nickel and asbestos deposits of the Thompson Nickel Belt and the New Quebec Nickel Belt are restricted to this orogenic front, no such deposits would occur under Hudson Bay.

Jan 1, 1973

By F. E. Lee

The following outline gives a brief account of some of the ways in which microscopy is applied to the problems arising from the various operations of the Tadanac reduction works, at Trail, B. C. The Sullivan ore is a very fine-grained mixture of galena, marmatite, pyrite and pyrrhotite. The separation of minerals associated so intimately is a difficult task and requires careful control. Various oils and reagents are used in the process as developed, and it is essential that the operators have a means of control which shall be rapid, and at the same time, approximately correct. This result is obtained by microscopic analysis in the following manner: The operator places a quantity of the material upon a slide, a drop of water is added, and it is covered with a cover glass. Upon examination with transmitted light, the zinc mineral particles appear reddish, the ordinary gangue colorless, the lead and iron sulphides opaque. This method has proved of great assistance both in the development and in the operation of the present method for concentrating Sullivan ore. The miscroscope has thus become as much a part of the metallurgical equipment as the balance and burette. The microscope used in the laboratory is a Fuess "petrographic" with a specially-made vertical "illuminator" by Bausch & Lomb, with the usual accessories.

Jan 1, 1924

By V. Loya

Metallic foams (MF) are relatively new materials with a combination of attractive properties (permeability, high surface area, thermal and chemical stability, etc,), They can be produced from different materials and can be manufactured using various processes, Due to their unique properties, they find applications in different sectors of engineering, such as energy absorption, filtration, heat dissipation, etc, For many applications, the permeability is an important parameter to characterize and optimize, Most of the recent literature on the subject studied the permeability in the low velocity range. The present study was carried out to have a better understanding of permeability for greater velocity ranges, An equipment was designed and built for this purpose, Pressure drop measurements were made across the thickness of open-cell nickel foams, Pore and window sizes were measured by image analysis on SEM micrographs, The experimental results are in relatively good agreement with the Hazen-Dupuit-Darcy model (R2>98%), The permeability is affected by pore size, porosity and the normalized projected area of the connecting pores (ie. windows).

Jan 1, 2005

By Robert R. MacLachlan

New underground mining technology is evolving through the use of large-diameter bore holes containing individually restricted charge weights. This article presents summary observations on cube-root scaling trials using single and rows of charge blasting in sand and in frozen ground. These observations have some bearing on the evolving underground practice, especially where charges of appropriate geometry are used.

Jan 1, 1978

By A. S. Baillie

THE subject of taxes appears to engage our attention altogether too lightly. At least it would seem that, notwithstanding the increase in the cost of government, and its concomitant increased taxation, little constructive work is being done with a view to solving the problem of increased taxes. I believe that the inattention of the public generally to the subject of increased taxation is due largely to the fact that shareholders are not advised of the amount of taxes paid by industry. Were companies to advise their shareholders the amount of monies paid or payable out of each year's earnings for taxes in one form or another, and were such amounts compared with the amounts available for distribution to shareholders, the effect would be a general demand for more equitable taxation methods. While I am not unmindful of the burdens and inequities in taxation confronting industry generally, I believe that the mining industry in this Province does not fully appreciate the burden represented by the costs of taxation. My reason for this belief is based partly upon1the fact that no serious effort has so far been made to devise some means By which the mining industry in British Columbia might protect itself against the ever-increasing burden of taxation. In addition to this fact the widely diverse nature of mining in British Columbia makes the accumulation of comparable data a problem which, so far as I can ascertain, has never been attempted in a manner which would be authoritative. It should not be necessary to cite the effects of this burden upon any one mining company or upon any branch of the mining industry, such as coal mining, placer mining, base-metal mining, or the precious-metal mines. In my opinion, the operation of our mines by large corporations is conducive to the payment of taxes with much less protest than would be the case were the taxes being taken out of the earnings of just a few partners or a very few shareholders. We appear to be too unmindful of the taxes, paid by mining companies, of a kind that are not so prominently brought to our attention as are the taxes which are calculated upon the taxable income of the company at the end of its fiscal year. British Columbian mining companies pay many other taxes besides those which are calculated upon taxable income. Among these are school taxes, property taxes, gasoline taxes, mineral taxes, coal royalty, to say nothing of fuel-oil tax, sales tax, and excise taxes.

Jan 1, 1935

By François Baillargeon

Two types of ore deposit provide the bulk of the world nickel production. They are the hypogene magmatic massive sulfide deposits and the supergene lateritic deposits. Platinum group elements (PGE) are also extracted from magmatic sulfide deposits. Recent sky-rocketing price of palladium has prompted the mineral industry to seek alternative resources. In such a manner has emerged the Lac-des-Iles type of target, a very low sulfide-bearing bulk tonnage type of deposit. Furthermore, unconventional (e.g. non-magmatic) types of deposit are now sought more intensively (Wilde et al., 2003). Considering both this trend of the PGE Industry, and that only a few magmatic deposits account significantly for the world nickel production, someone may wonder if a diversification of the hypogene nickel resources base would not be needed in the near future. Laterites are residual deposits developed on ultramafic rock under wet tropical climate. Are all ultramafic protoliths equal to generate high-grade lateritic deposit? Are some preweathering processes important to generate favourable ultramafic protoliths? The mineralogical heterogeneity of some ?dry? lateritic nickel deposits renders their ore beneficiation difficult. Is the type of nickel-bearing mineral found in the protolith a significant factor influencing the laterite heterogeneity? To contribute to answer all these questions, we have undertaken a research project on the nickel occurrences of the southern Quebec serpentinite belts. Why choosing this specific region for such a project? First because, due to continuous mining of asbestos ore since 1870, the serpentinite belts of this region are among the best exposed and studied in the world. Secondly, this region host a complete spectrum of nickel deposits that have been described before in the scientific literature. Furthermore, this region is slightly to moderately metamorphosed which make it perfectly suited to study the departure from magmatic nickeliferous paragenesis through various metamorphic conditions. As a matter of fact two orogenic events affected this region, the Taconian, in Ordovician time, and the Acadian during the Devonian. The magnitude and the timing of these dynamo-metamorphic events vary considerably through the region (Gauthier et al., 1994). These variations are now well constrained due to precise age dating.

May 1, 2003

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By Tassos Grammatikopoulos

The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies of the Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoe-shaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York State, no carbonate protolith is preserved and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560 oC, or, alternatively, 550 MPa and ca. 630 oC. Several high grade zones, averaging >40%, but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 - 2 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates. St. Lawrence compares favourably to other known prospects and operating wollastonite deposits; having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production.

May 1, 2002

By M. Yao, D. Thibodeau

"Selective mining, such as post pillar cut and fill, is used in large, flat, irregularly shaped ore bodies where ground stability is to be maintained. This selective mining is used to open the stope to the full lateral extent of the ore body in order to minimize the dilution and maximise the recovery. For increased mining depth, design of the post pillar becomes more challenging since those pillars will eventually fail as mining progresses upwards. The post pillar should be designed such that failure does not occur at the early mining stage, such as at the first cut. After mining progresses upwards, the post pillars are expected to fail but be confined by backfill. In order to maximise ore recovery, both drift width and post pillar size must be designed adequately with a consideration of all geomechanic parameters. This paper will describe the process used to design post-pillar cut and fill for one of the ore bodies in Vale’s Copper Cliff Mine using a combination of both empirical deterministic and numerical modelling techniques. By utilizing both empirical deterministic and numerical modelling techniques drift width and post pillar size can be effectively designed. Current post pillar cut and fill design in the existing Vale operations are used to validate the design for Copper Cliff Mine. INTRODUCTIONCopper Cliff Mine is located within the Copper Cliff Offset in the limits of City of Greater Sudbury, Ontario, Canada, as shown in Figure 1. The Copper Cliff Offset extends about eight kilometres south from the Sudbury Igneous Complex into the footwall rocks. Until 2008, the current Copper Cliff Mine was operated as two separate mines i.e. North Mine and South Mine. However, as part of restructuring of Vale Ontario Operations, the North and South Mines were merged in 2009 to form the “Copper Cliff Mine”."

Jan 1, 2015

By Brian W. Mackenzie

"This paper briefly outlines the characteristics which should be considered in assessing the economics of mineral exploration, and illustrates such an assessment by using data from the Canadian base metal sector. Implications for the sector are found to include the following:(1) base metal exploration has the potential to create a substantial amount of new wealth;(2) investment incentive for exploration under current conditions is not unattractive over-all;(3) because of existing taxation policies, there is much more incentive for large companies to explore than for smaller enterprises;(4) succesful exploration is sensitive to the size, financial resources and organizational structure of the exploration entity;(5) the general level of recent exploration expenditures should be adequate to maintain the current rate of production and perhaps to support very modest growth; and(6) there is an important opportunity for growth in the sector.The findings of the study suggest that government policies should be made more flexible, in order to take into account the risks associated with exploration and with price fluctuations in the base metal sector. Recommendations are also made concerning improvements in provincial regulations for disclosure of exploration information."

Jan 1, 1981