Search Documents

This paper describes basic parameters, such as surface forces and film elasticity, affecting the stability of foams (two-phase froths). We used the thin film pressure balance (TFPB) technique to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG). The results were compared with the foam stabilities measured experimentally and the film elasticities calculated using a new model developed by Wang and Yoon (2006). It was found that at low electrolyte (NaCI) concentrations foam stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother type and concentration. Further, the kinetics of film thinning was studied at a high electrolyte concentration. The results obtained in the present work showed that the major role of a frother is to decrease the hydrophobic force rather than to increase the film elasticity. This conclusion is drawn from the observation that at the typical frother (MIBC) concentrations employed in flotation, frother additions cause sharp decreases in hydrophobic force while causing relatively little changes in film elasticity.

Jan 1, 2006

By W. Harry Foster

"Asbestos Corporation Limited, incorporated in 1925, operates four asbestos mines and three asbestos mills in the Thetford Mines 1•egion of Quebec's Eastern Townships. A unique asbestos orebody, located in the Ungava Peninsula of Nouveau Quebec, was purchased by Asbestos Corporation Limited in 1964 and commenced production in 1972. As there were no existing facilities in the isolated, arctic region of Asbestos Hill, it was necessary for Asbestos Corporation Limited to construct at Deception Bay a deepsea wharf, a large ungraded fibre shed, a power plant and camp facilities. Forty-two miles of road were needed and were constructed from Deception Bay to Asbestos Hill. At Asbestos Hill, a complete crushing-drying-milling complex, a power plant, pe1•sonnel accommodations and open-pit facilities were provided. Unloading facilities and a fib1•e finishing mill we1l constructed at Nordenham, West Germany. The ""Asbestos Hill- Nordenham Story” is divided into individual papers covering all aspects of the engineering, construction and operation of this unique enterprise. Particular emphasis has been placed on those unusual aspects caused by the isolated location, arctic conditions, short shipping season and the deep permafrost."

Jan 1, 1976

By Robert H. Clark

Introduction During the last twenty years, science and industry have been strenuously endeavouring to discover new sources and new kinds of liquid fuels and to work out suitable chemical methods for their production. One of the new possibilities for the production of liquid fuel on a large scale is law-temperature carbonization of various grades of coal. The use of alcohol as motor spirit, in spite of its relatively low calorific value, is being widely investigated. Its production by fermentation of sugars, its recovery from the sulphite liquors of the paper industry, its production directly from wood and also from calcium carbide, have all been considered. At present the most promising line of investigation would appear to be the further development of those technical processes which yield liquid fuels from coal; since science has shown the possibility of preparing all kinds of liquid fuels and even the complete conversion of coal into oils. The present paper will consider briefly: 1. The production of primary tar by low temperature carbonization of coal. 2. The hydrogenation of coal. 3. The synthetic processes of Dr. Franz Fischer.

Jan 1, 1928

By A. Djebara

Today, indoor air quality, especially in manufacturing industries, is of great interest due to the use of new processes and advanced materials such as those containing nanoparticles. Manufacturing processes generate aerosols (dry or wet) which can be detrimental to occupational health and safety and to the environment. Controlling metallic particle emissions during machining processes should limit their formation at the source, and thus minimize the risk of exposure; this at-source reduction requires the characterization of the particle emitted (size, nature, concentration, etc). The metrics normally used in characterizing fine and ultrafine particles include the mass concentration, the specific surface and the number concentration. Most of these metrics are affected by the size, the geometry and the density of the measured particles. Information about the form and the real size of the particles is thus very important. A procedure for collecting and characterizing fine and ultrafine metallic particles was developed and applied to the study of particles emission during the machining of aluminum alloys. It was found that metallic particles emitted during the machining of aluminum alloys are of various shapes and sizes, and this information must be taken into account when characterizing these particles.

Jan 1, 2011

By F. W. Gray

Foreword: It is not my purpose, in this address, to write the history of the Geological Survey of Canada, which has from time to time been reviewed by the officers of the Survey itself, and by men more competent than myself to handle so large a subject, but rather to set out some of the reasons for the regard in which the Survey is held by our Institute, the body best qualified to speak for the mining men of Canada. And, a further purpose is to publish the desire of our Institute that the work of the Survey shall be maintained at the highest pitch of efficiency the resources of our country. will permit, because to scrimp expenses on the Survey is 'to save at the spigot and lose at the bunghole." A historical examination of the grounds on which it may be asserted the Geological Survey has been, and still is, of fundamental economic value to our country, discloses a prescience on the part of the forefathers of Canada, calling for our admiring gratitude, and reveals a unanimity among the real leaders of Canadian thought, on the value of geological knowledge, that is impressive in its continuance dawn to this date. There seems always to have been before our people the realisation that large stretches of Canada are unfitted for agricultural settlement, and that our glaciated areas, the barrens and tundra of the North, and our extensive mountain ranges, had promise of compensating mineral content which the geologist and the prospector, labouring together through the years, would disclose. The Geological Survey is one of Canada's oldest public services, distinguished by an unimpaired tradition of honourable and useful labour. Founded in 1843, under William Edmond Logan, not yet 'Sir William', one year after the Act of Union, it was directed by him until 1869, or into the early years of Confederation, so that the early years .of the Survey were also, politically, the formative years of Canada, as we know her today.

Jan 1, 1932

By M. Tadie, J. Wiese, K. Corin

The use of potential control in the flotation of ores has been applied in a variety of operations and presents an opportunity for improvement of selectivity and recovery of valuable minerals. Although it is possible to vary the redox potential (Eh) using chemical additives such as sodium hypochlorite or hydrogen peroxide this is more commonly done by varying the pH and dissolved oxygen (DO) concentration. The present study involves an investigation into the effect of varying dissolved oxygen concentration, ionic strength (IS) and pH on the flotation response with the aim of application to a South African lead-zinc ore. In all cases the Eh is measured as a function of the different DO, IS and pH values. The main objective was to achieve selective flotation of galena from sphalerite. The first part of the work was micro-flotation tests conducted on single minerals with galena used as the basis for effect of the factors studied on redox potential and ultimately recovery. The DO was varied by alternating between the use of air and nitrogen as the gas source to the micro-flotation cell. PH was varied between pH 9.2 and pH 11.8 using sodium hydroxide. In the first part of this study a factorial design approach was used to determine the interactive effects of the variables tested, viz. DO, ionic strength and pH, on the Eh and on the recovery. Redox potential was measured using a combination electrode made up of platinum wire and Ag/AgCl reference combination. Recoveries indicated that pH had the most significant effect on recovery and Eh. The influence of redox potential on recovery was found to be of relevance to the condition of high dissolved oxygen concentration and less so at low dissolved oxygen concentrations. It was also noted that that the combined interaction between ionic strength and dissolved oxygen concentration had a positive effect on recoveries, however this was not so with Eh. The chemistry of the ions in solution was observed to play a dominant role on the recovery due to changes in solubility arising to pH modification. The longer term objective of this work is to determine the optimal Eh conditions for the separation of galena from sphalerite.

Jan 1, 2016

By Jie Deng, Wenliang Xiong, Binyan Chen

"With falling rare earth metal prices, low cost beneficiation of rare earth minerals is essential. The “Flotation-Agglomeration-Magnetic” (FAM) separation process is a newly developed technology by IMUMR to economically recover rare earth elements from different types of deposits. The theory of FAM process is to selectively agglomerate rare earth particles and separate from gangue minerals by bubble flotation process. The flotation product is further upgraded by magnetic separation. The FAM process has been successfully applied in industrial production on the Dalucao rare earth ore, Sichuan, China. The average REO grade of rare earth concentrate is 65% in the latest 12 month production run, with an average recovery of 55%.INTRODUCTIONRare earth elements (REEs) include fifteen lanthanide elements coupled with two chemically similar elements (yttrium and scandium). These elements are split into two sub-groups, La to Sm are classified as light rare earth elements (LREEs) and the remaining elements including yttrium are heavy rare earth elements (HREEs) (Kumari & Panda, 2015). The demand of rare earth elements surged in recent years due to their increasing usage in diverse industrial aspects including high strength magnets, phosphors, clean energy, polishing compounds and catalysts (Goley &Scott, 2014).More than 250 REE-bearing minerals have been discovered, but many minerals are with very low concentrations of REEs, varying from 10-300 ppm (Adam &Ping, 2013). The most common rare earth minerals mined are bastnaesite, monazite, xenotime and ion-adoption REE (Chelgani & Rudolph, 2015; Kanazawa & Kamitani, 2006). Before the 1960s, most rare earth resources were extracted from monazite in the beach placer, with the exploiting of Mountain Pass in the United States and Bayan Obo mine in China, bastnaesite became the chief mineral source of rare earth resources (Klinger, 2015). These minerals are commonly separated with gangue minerals by froth flotation, gravity concentration, magnetic separation, or any combination thereof based on their specific physical characteristics (Zhou & Wang, 2014; Adam & Richard, 2014; Yang & Satur, 2015; Xia & Brian, 2015a,b)."

Jan 1, 2016

By K. Sakaguchi, T. Yokoyama

"In-situ rock stress measurement was carried out in the Kamaishi mine of Iwate Prefecture to quantify the variation of the shallow crustal stress field associated with the 2011 Tohoku-oki earthquake. Stress measurement was conducted by the Compact Conical ended Borehole Overcoring (CCBO) technique, which is one of the stress relief method. The CCBO technique is the one of the suggested method of ISRM. Measurement period is from 1991 to 2014. Main results obtained in this study can be summarized as follows.The direction of the maximum principal stress did not change much before and after the earthquake. However, the directions of the intermediate principal stress and the minimum principal stress of one year after the earthquake changed from those of before earthquake. Namely, the direction of intermediate principal stress was East-West horizontally, and the direction of minimum principal stress was vertically. This state of stress is reverse fault type and was maintained for three years after the earthquake.The magnitudes of principal stresses and the vertical stress of one year after the earthquake became more than the double before the earthquake. However, the magnitudes of the maximum principal of two year after the earthquake became smaller comparing with those of one year after the earthquake. Furthermore, the magnitudes of the intermediate principal stress and the minimum principal stress of two year after the earthquake became almost same as those before earthquake, and the vertical stress of two year after the earthquake became almost equal with the overburden pressure. And the magnitudes of three principal stresses of three year after the earthquake became the same level before the earthquake."

Jan 1, 2015

By H. Q. Fan

Construction equipment is an important type of resources of heavy construction contractors. Since equipment breakdowns can cause project delays and significant financial losses, the contractors are eager to know those factors causing equipment failures directly or indirectly, related to equipment design, maintenance, and operations. Although Bayesian network can be used for diagnostic analysis of failure events or making predictive analysis, building a Bayesian network for such purpose can be difficult as the cause-effect relations can be subjective and their conditional probabilities change with a wide variety of causal factors. A hybrid approach is proposed in this paper to update the Bayesian diagnostic network structures and parameters using real life data, the conditional probabilities and cause-effect relationships can be dynamically updated with observed failure records to reflect the real life situations of a complex equipment system. A case study is conducted to show the benefits of the hybrid approach in construction equipment diagnostic analysis.

Aug 1, 2013

Building block cave operations involves significant commitments to capital and time before arriving at completion or full scale production. The focus of the mine planners is habitually to minimize the upfront capital and achieve target development rates and construction dates. However, management of the construction of block cave projects requires understanding of the strategic/tactical decisions that the project planners can take to increase the value of the project and cope with schedule risks. As block cave projects involve development of vertical and lateral access to the underground footprint and ore body, more attention to uncertainties is required as most of those projects need to confront delays leading to a decrease in value. The standard process of development and construction scheduling is often not planned with provisions to realise uncertainties in the construction phase. Uncertainties and risks such as poor ground conditions and equipment breakdowns are the primary reasons for schedule slippage. As a result most of these projects experience delays. In order to mitigate risk to the project schedule, we centre our attention on increasing the value of the project by spending more money upfront and improving the schedule rather than focus on minimizing the upfront capital. Scenario-based simulations along with project appraisal methods hold great promise to address those challenges and enable mine planners to make better decision and enhancing project value. This paper will present a hybrid simulation based approach to model the process of development and construction based on discrete event (DES) and continuous based simulations (CBS). Such simulations will be conducted for scheduling multiple development headings (Apex, undercut, extraction, and haulage levels). Two scenarios are utilized to investigate the impact of risks on schedule and how flexibility in construction can be incorporated to minimize delays: (1) The bench mark scenario is created based on actual data from an existing case study. (2) The flexible scenario is an alternative way to use primary production infrastructure (Ore Handling System) including conveyer drifts, conveyer belt, and a gyratory crusher in the construction process and that requires the system to be in place before starting lateral development in the footprint. As a result, a truck-load system versus a conveying system will be studied to observe the gain in construction speed and to estimate the premium cost for mucking rock from headings and drawbells and transporting it to surface. Such strategic flexibility would be part of the original budget to make the tactical flexibility available during construction. Continuous cash flow models are used to evaluate and compare the scenarios. This study is an example of how new techniques in planning can be used to support decision-making processes in block cave design.

Aug 1, 2013

By D. J. Houlahan

ABSTRACT Sorting has the potential to massively improve the pro?tability of mining base metal, hard-rock ores. However, several barriers to the increased application of sorting have been identi?ed, including a lack of mineral-speci?c sensors available to the industry. This paper presents the outcomes of acollaborative project to develop an induction-balance sensor speci?cally for low-grade copper and nickelores. A review of the basic principles of induction-balance sensing and of the sensor-rock interaction is presented. Early development and testing of the sensor on ores from the Thompson nickel belt in northern Manitoba is discussed. Shortcomings of the prototype identi?ed in early testing have now been over-come, leading to improvements in design and construction, as well as sensor accuracy. The improve dsensor has now been tested on additional ores from the Sudbury Basin, with good results. A discussion of potential applications is presented and recommendations for future development are made.

Jan 1, 2010

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By G. Molloy

The purpose of this paper is to demonstrate the value of applying continuous improvement, in particular 5S and standard work, in an underground environment. 5S and standard work are two aspects of Lean manufacturing that have been applied in many industries. At Vale Canada Limited, the focus is to first stabilize the process, commonly through the use of 5S, standard work and other continuous improvement techniques. In parallel with building an engaged workforce, these approaches aim to incrementally stabilize and improve a process. 5S is an employee-driven, systematic methodology to reduce waste in all its forms through attaining, maintaining, and improving workplace organization. Identified as a foundational part of any improvement process, 5S aims to remove wastes that impact on the overall efficiency of the area. Standard work is used to formulate a common approach to how tasks are carried out to ensure consistency. Standardization involves identifying, establishing, and following the best method. The aim is to eliminate the variation that can occur when there is not a pre-defined established standard. Demonstrating the value of 5S and standard work in an underground environment will be achieved by first understanding the overall concept of Operational Excellence and continuous improvement as practiced within our operations. The paper will then cover a real application of 5S and standard work within the underground environment at Thompson, Manitoba.

Aug 1, 2013

Vast quantities of cosmic material, ranging in size from fine dust to large meteorites and planetoids, have been colliding with and accumulating on the earth since its origin 4.5 billion years ago. There are less than twenty well preserved meteorite craters and Jess than thirty fossil craters or astroblemes on the present face of the earth. On the moon, there are approximately 200,000 craters on the visible face alone -the largest crater being 132 miles in diameter and attaining a depth of 16,000 feet. Making allowances for the different physical conditions on the moon and assuming that these lunar features are of impact origin, the indifference is that, since primeval time, large numbers of celestial objects have also encountered the earth, but that both the topographic expression of the impact and the objects themselves have been destroyed by weathering and erosion. It may be reasonable to suggest that additions of cos-mic bodies have materially altered the chemistry of the earth's crust from place to place and that the impact of large meteorites and asteroids has created zones of weak-ness in the crust that could be the center of magmatic intrusion and mineralization.

Jan 1, 1965

By H. H. Wober, P. J. Morgan

"The proposed classification of ore reserves based on geostatistical and economic parameters is designed to be used as a communication tool to identify for investors, bankers, and financial analysts the degree of risk associated with a specific class of ore reserves. The class designation identifies the degree of accuracy of the estimates for tonnage and grade of annual production volumes of ore. It thus enables decision makers to quantify the risks and uncertainties inherent to the ore reserve in achieving over-all economic goals and annual financial objectives.IntroductionDuring the evaluation, in 1980, of the Creede silver deposit in Colorado, U.S.A., as a potential bulk mining project, the authors were faced with the problem of conveying to senior management the risks and uncertainties that are implied by using common or conventional classification systems to categorize ""ore reserves"". The estimated numbers for tonnages and grade of the projected ore reserves represented the only entry for future revenue from the project. It was, therefore, necessary to convey to management the level of risk associated with those numbers when implementing further stages of development, and to convey what impact significant differences would have on the profitability of the project. The desire to quantify these risks led to a revised definition of ""ore"" and to a re-examination of the classification system of ""ore reserves"". Traditional methods for estimating tonnage and grade of reserves do not include a quantification of the errors of these estimates. The advent of geostatistical methods made this quantification possible. The proper application of geostatistical methods, with adequate geological input and a reliable set of sample data, is essential to its validity.Others have proposed a classification of ore reserves based on geostatistical parameters. Diehl and David (1982) recognized ""that concepts of proven, probable and possible have to be linked to the production rate or time horizon"". Royle (1977) had also addressed this problem. Forsyth (1987) pointed out that bankers are concerned with ""the probability that the variability will fall within a certain degree of accuracy"" especially for grade estimates, and would like to see grades expressed together with the error of the estimate at the 950Jo confidence level."

Jan 1, 1993

By A Turek

The Lake Cinch deposit occurs in the Tazin gneisses on the footwall side of the Black Bay fault. Ore is localized by two faults, the Main Ore fault and the Cracking-stone River fault, occurring in shoots along the former and on tension fractures between the two faults. Faulting leading to the localization of the deposit is analyzed in detail and tied into the regional pattern. Pitchblende, the chief radioactive mineral, is investigated by X-ray and found to be of very small particle size. The relation-ships of U, Fe and Mn in the ore are established quantitatively, and Fe is found to bear a catalytic relation to U. The deposit is classed as belonging to Lindgren's mesothermal class. Mineralization is attributed to carbonate solutions, and the uranium is believed to have been trans-ported in the hexavalent state as the uranyl tricarbonate ion; analogy is drawn to a recently developed hydro-metallurgical technique for the production of uranium dioxide. Introduction THE Lake Cinch deposit is located in the Beaver-lodge Camp, Saskatchewan. The property was staked in 1948 and went into production in 1957

Jan 1, 1965

By J. P. Messervey

As a result of my field examinations in this Province, I have been struck by the evidence of widespread mineralization in rocks, particularly the limestones of Carboniferous age. Six prospects of lead and zinc or lead alone scattered through the eastern part of the mainland, one copper prospect and three veins of siderite, all point to a period of mineralization subsequent to the forming of the Carboniferous rocks in which they occur. While none of the present prospects are of proved economic importance, still it is possible, and indeed probable, that further prospecting will find concentrations sufficiently large to make mines. It may possibly aid the prospecting for these base metals if the present scraps of information are assembled from various sources, and I will further briefly recount the information as a result of my observations. Gay?s River At Gay's river, midway between Halifax and Truro, and four miles east of the railway, numerous pits and natural exposures show galena and sphalerite in limestone of Carboniferous age, near where it lies unconformably upon slate and quartzite of the gold series. These exposures extend for a length of over one thousand feet along a curving contact. The pits show that on the contact there is a fossiliferous and somewhat porous layer of limestone, which is so impregnated with galena and small amounts of sphalerite as to be of ore grade. Wherever observed, the thickness of this layer is less than two feet.

Jan 1, 1929

By Nelson Hogg

"THE NOR-ACME gold mine is located close to the north shore of Snow Lake, at 54°53' north latitude and 100°03' west longitude. It is about 75 air miles east of Flin Flon, and 36 miles by road from Wekusko at Mile 81 from The Pas on the Hudson Bay Railway.The claims which contain the Nor-Acme orebodies were staked in 1927 by C. R. Parres, who, with his sons, held the ground until 1938 when Nor-Acme Mines Limited was incorporated. In 194 l, on the recommendation of F. Ebbutt (1), this property was optioned by the Howe Sound Exploration Company, Ltd. A program of 50,000 feet of diamond drilling resulted in the outlining of two orebodies containing an estimated 5,000,000 tons with an average grade of 0.15 ounces per ton to a depth of 1,000 feet.A period of inactivity during the war years was followed by the construction of a mining plant capable of treating 2,000 tons of ore per day. Milling started in March 1949, and to the end of 1954 has resulted in the production of 383,793 ounces of gold and 32,906 ounces of silver from 3,331,403 tons of ore.General GeologyThe general geology of the Snow Lake area is described by J. M. Harrison (2), and will not be discussed here except insofar as it affects the Nor-Acme orebodies. The orebodies occur in rocks of Precambrian age that have been classified by Harrison as the Snow group, comprising meta-morphosed sediments interbedded with acid and basic volcanic rocks. The volcanic rocks include pyroclastic types which are unique in the region, a fact which led to their classification in the Snow group rather than the more widespread Missi group that generally occupies the same stratigraphic position above the Amisk group (Figure 1)."

Jan 1, 1949

By R. A. Ford

The paper outlines: methods used for the determination of wear metals in motor and transmission oils; contaminents in motor, transmission and crusher lubricating oils; and viscosity determinations. Case histories and costs are presented to illustrate the value of an oil analysis program. Introduction NORANDA MINES LIMITED (BELL COPPER DIVISION) is located on the shores of Babine Lake, approximately 450 miles north of Vancouver, British Columbia. Access to the mine is by road from Topley, B.C., about 40 miles away. When a preventive maintenance analysis program was first considered, it was obvious that if samples were to be sent out for analysis, results would not be available for at least a week, due to the distance from any commercial laboratory. The assay laboratory was asked to investigate the possibility of determining wear metals on site. A limited program was started soon after production commenced, and this has now grown to include all large mobile equipment as well as crushers and grinding mills. The laboratory also now determines viscosity, fuel dilution, dirt and abrasives, glycol and water. All these results are ready within two days. This paper will outline the methods used, data interpretation, several case histories and the benefits from such a program.

Jan 1, 1977

By H. Karakul

Determination of P-wave velocity (Vp), which is closely related to intact rock, is a nondestructive, easy and less complicated procedure. Due to these advantages, there is an increasing trend to predict the geomechanical properties of rocks from Vp. In addition to mineral content, cementing material and porosity, degree of saturation (Sr) are also other factors influencing geomechanical properties of the intact rock. However, up to the present, in the studies on the prediction of geomechanical properties of rocks from Vp, the effect of Sr has not been investigated. By considering this issue, in this study, it was aimed to correlate strength properties (uniaxial compressive and tensile strengths) and Young’s modulus with Vp of various rock types under different degrees of saturation. In addition, geomechanical properties of rocks were estimated from theoretical P- and S-wave (Vs) velocities, which were calculated based on their mineralogical compositions. For this purpose, fourteen different rock types were collected from several parts of Turkey and a comprehensive laboratory testing program was conducted. In the statistical analyzes, a series of different prediction relationships were developed by using independent variables such as Vp, Sr and effective clay content (ECC). Simple regression analysis results indicated that although prediction of the geomechanical properties of rocks from Vp at different degrees of saturation was possible, the equations developed would yield some under- or over-predictions. On the other hand, the multivariate equations developed have very high prediction performances and are very useful tools to estimate the geomechanical properties from the measured Vp at any Sr value. In addition to mineralogy, the variation in geomechanical properties with increasing Sr is also associated with the combined effect of porosity and clay content, which is first described in this study by the term Effective Clay Content (ECC). It is also noted that strength properties of rocks at any Sr may also be estimated using the empirical relations based on the theoretical Vp and shear-wave velocity (Vs) values, which are calculated from their mineralogical compositions.

Jan 1, 2015