Search Documents

By Walter Greaves

THIS paper describes a series of tests performed at the Hollinger mill during the past four years, in which both metal and rubber-lined pumps were used for pumping sand and slime. While conditions will not be the same at other mills, it is felt that the information gained from the tests should be of value to other operators and of assistance to them in selecting the most efficient size of pump and kind of lining for economical operation. For the successful operation of pumps with rubber linings there are certain conditions, which, if recognized at the outset, will save the operator a good deal of work and trouble. First is the necessity of keeping sharp pieces of steel, or anything that might cut the lining, out of the pumps. This can be effected by placing screens in the proper locations. Second is to recognize the fact that the rubber lining of the shell, and the rubber cover of the impeller, are subjected to very different conditions. The shell lining, :being at rest and well supported by the metal case, has a relatively easy job compared ? with the impeller covering, which is subjected to centrifugal force and has a tendency to tear itself away from the metal core. Also, the pulp travels through and past the impeller at a high velocity. These two factors, centrifugal force and velocity of the pulp, would appear to set a limit to the speed at which, for a given set of conditions, it is economical to run a rubber-covered impeller. Therefore, a pump should be large enough for the work to be done. To get the best mechanical efficiency, it must be operated somewhere near the limit of its capacity, but this may not give the best overall cost, because the saving in power, due to the high efficiency, may easily be lost through excessive wear on the lining. It would appear that this condition is more critical in a rubber-lined pump than in one lined with metal.

Jan 1, 1939

By J. M. Livingstone

"This paper covers some of the problems confronted by Canada's railways in moving bulk materials from their source to the dock-site. The ""cost center"" concept is presented, and hypothetical examples of its use given. Also discussed are systems design, the unit train and pipelines.INTRODUCTIONCANADA LIVES BY RER EXPORTS and the Port of Vancouver by the exports of the Mountain and Prairie Empire at her back. The most recent estimates of off-shore shipments of bulk from the Port of Vancouver rise to 35.8 million shipping tons in 1985 and deep-sea general cargo estimates, in and out, are estimated at 7.6 million shipping tons for the same year. This compares to 7.67 and 2.87 million shipping tons, respectively, in 1965."

Jan 1, 1968

By P. P. Rosario

A research project was conducted at the University of British Columbia (UBC) resulting in the development and evaluation of a novel comminution circuit incorporating autogenous grinding and parallel trains of cone crushers and high-pressure grinding rolls (HPGR). A primary driver for the circuit was to treat ore from deposits with clay and variable hardness. This paper summarizes the unique pilot-plant test program that was developed as a basis for experimental simulation and lists the main findings of the research, including the circuit?s potential operational cost savings compared to a conventional SAG circuit.

Jan 1, 2012

By Andrew Gillam

Outline of Presentation ? AMEC overview ? Benchmarked companies ? GRI 3.1 Guidelines ? Best practice examples ? Report content and boundary ? Strategy and profile ? Environmental ? Social GRI G3.1 ? Gold Standard for Reporting ? GRI ? Global Reporting Initiative ? 1997 outgrowth of Coalition for Environmentally Responsible Economies (CERES) and UN Development Program (UNDP) ? Official collaborating centre of UNDP and works in collaboration with UN Global Compact ? Coalition of companies, business organizations, accounting firms, CSR consulting firms and nogovernmental organizations (NGOs) ? Mission: develop and disseminate globally applicable Sustainability Reporting Guidelines ? Now de facto CSR reporting standard; appeal lies, in part, with supported flexibility in reporting approach and scope ? Latest generation G3.1 (March 2011); includes expanded guidance for reporting on human rights, local community impacts and gender

Aug 1, 2013

By Jean-Jacques Bouillon, Michel Jébrak, Stephane Faure

"Le gisement polymétallique (Cu-Zn-Au-Ag) des Mines Selbaie est forme par un réseau de filons encaisses dans une séquence de pyroclastites felsiques du sill on Harricana-Turgeon. Les minéralisations sont encaissées dans le tuf de Selbaie, situe sous une épaisse séquence d'ignimbrites Iitées. Ce gisement se distingue des autres gites archéens par une chronologie atypique des minéralisations: les veines de chalcopyrite, de sphalérite et de galène recoupent un amas exhalatifpyriteux stérile. Un vaste halo d'altération hydrothermale a chlorite et mica blanc est associe à cette minéralisation.La mise en place des veines minéralisées est associée à une phase d'extension NNW-SSE. Le complexe volcanique subit, par la suite, trois phases de déformation. Une compression, orienté N-S, développe une schistosité à peine pénétrative et un réseau de fentes de tension. Une réorientation des contraintes locales selon une direction WNW-ESE conduit au chevauchement de I' écaille d'andésite et de tonalite de Brouillan. Un réseau conjugue de failles normales cassantes est associe au relâchement des contraintes."

Jan 1, 1990

By G. R. Cope, J. S. Getsinger, K. D. Lund, T. Neale

"Mineral exploration in the Sicker Group, a belt of Paleozoic volcano-sedimentary rocks on Vancouver Island, has traditionally centred on auriferous polymetallic volcanogenic massive sulphide deposits such as those currently mined by Westmin Resources Ltd. near Buttle Lake. Recently, however, the focus of exploration in the Sicker Group has shifted toward targets of structurally controlled gold concentrations, with notable success. Major north and northwesterly-trending structural features such as the Cowichan-Horne Lake break (one of several regional high-angle thrust fault s active throughout a long period of geological time) and related fault systems have contributed to localization of gold mineralization.Using the extensive information database compiled by MPH Consulting Limited during numerous exploration projects in the Sicker Group, two cross sections through areas with significant gold occurrences southeast of Port Alberni are presented. The cross sections combine geological, geochemical and geophysical data in an attempt to emphasize the relationship between structural trends and gold mineralization. Examples from specific properties, including gold discoveries along the Mineral Creek fault zone, are used to illustrate this relationship."

Jan 1, 1990

?Hydrothermal breccias-genetic models ?Deep drilling-underground potential ?Deposit variety-test new ideas Exploration Summary

May 1, 2006

By Jaeheon Lee, Junmo Ahn, Doyun Shin

"Many alternative leaching systems including bacterial leaching have been introduced to avoid passivation on the surface of chalcopyrite and to increase the leaching efficiency of copper from chalcopyrite. Recently, glycine, one of the simplest amino acids, has been emerging as an efficient and environmental-friendly lixiviant to recover copper. In the present study, an alkaline glycine–peroxide lixiviant system was used to leach copper from chalcopyrite concentrate and the leaching mechanisms were also investigated by a suite of kinetic studies under different conditions. The chalcopyrite concentrate contains 28.8% copper with 30.8% sulfide sulfur. The effect of concentration of glycine and hydrogen peroxide of the leaching solution was investigated. Glycine concentration was varied from 0.5 to 1.0 M and the hydrogen peroxide concentration was changed between 3 to 5%. Leaching time and pulp density were also varied. Hydrogen peroxide is an oxidant of the system and the leaching efficiency with periodic additions of the peroxide was also studied. A mineralogical study was performed using XRD and SEM. To investigate the surface of the residue materials, XPS was used to see if any passivating layer was formed during the leaching. Detailed results from mineralogical, chemical, and metallurgical studies will be presented and discussed.INTRODUCTION The greatest global resource of copper is low-grade chalcopyrite and heap bioleaching may be the only economic option for its processing. However, formation of a passivating layer on the surface of chalcopyrite slows down the oxidation reaction and reduces the efficiency of the process."

Jan 1, 2017

By Diego L. Romero, Joy P. Romero

"IntroductionThe purpose of this paper is to explain the theory and demonstrate the industrial applications of electrostatic separation. Wabush Mines' use of this type of processing for the concentration of iron ore is unique in the industry. Other minerals are concentrated electrostatically but the process is not widely used.Typical minerals separated by electrostatic separation techniques are:Non-ConductorsAnhydriteApatiteBariteBastnasiteBerylCalciteChrysotileCorundumDiamondEpidoteFeldsparsFluoriteGarnetGypsumHornblendeKyaniteAcmiteAugiteBrookiteCassiteriteChalcopyriteChromiteColumbiteCopperDaviditeEuxeniteFerberiteFrankliniteGalenaGoldGraphiteHematiteMica (Biotite)Mica (Muscovite)MonaziteOlivinePerovskiteQuartzScheeliteSideriteSillimaniteSpheneStauroliteSulphurTopazTourmalineXenotimeZirconConductorsIlmeniteIlmenite-( High Iron)IlvaiteKoppiteMagnetiteMarmatiteMolybdenitePyriteRutileSamarskiteSphaleriteTantaliteWolframiteWulfeniteThe limitations of this process are:1. There must be a difference in conductivity between the minerals being separated.2. The size range must not be very wide.3. The specific gravity of minerals being separated should be similar or the minerals to be pinned should be lighter. 4. The feed must be dry.5. The particle shape should be more or less uniform. 6. The feed must not be high in true middling particles."

Jan 1, 1989

By David R. Ray, Arthur J. Pyron, William F. Thomann

"Proterozoic plutonic and volcanic rocks in the Franklin Mountains, west Texas, exhibit similar values in average concentrations of equivalent uranium (eU), equivalent thorium (eTh) and equivalent potassium (eK) when compared to Proterozoic igneous rocks of the southwestern United States. Variations of radioelement concentrations for all Proterozoic igneous rocks of the Franklin Mountains range from 1.1 to 357.1 ppm U, 2.1to 259.1 ppm Th and 2.5 to 10.2% K.Recent geologic mapping of the Proterozoic rocks in the Franklin Mountains revealed several types of granites previously unrecognized, and these warrant further exploration for U and Th resources. Fluorite-bearing granites and riebeckite pegmatites are likely targets for further investigation, as these have the highest U and Th concentrations compared to all other granites.IntroductionThis is a summary of the paper presented at the CIM Geology Division Uranium Symposium held in Saskatoon, Saskatchewan, September 8-13, 1981. The purpose of this study was to evaluate the distribution of uranium (U), thorium (Th) and potassium (K) in Proterozoic igneous rocks in the Franklin Mountains, and compare radioelement concentrations to Proterozoic igneous rocks elsewhere in the southwestern United States.General GeologyThe Franklin Mountains are located in west Texas and southcentral New Mexico, within the southeastern part of the Basin and Range Province o f the southwestern United States. The Franklins are a complex fault-block range trending northsouth with strata dipping toward the west. Ages of the rocks range from Proterozoic to Cretaceous. Harbour (1972, 1960) provides the most recent account of the general geology of the Franklin Mountains. Most recent accounts of the detailed Pro Proterozoic geology o f the Franklins are provided by Hoffer (1976), Thomann (1980, 1981), Pyron (1980), Ray (1982) and McCutcheon (1982)."

Jan 1, 1983

By F. Sorenson, P. A. Castellarini, F. Garbarino, M. N. Garcia

"Recently, significant efforts to improve productivity from the tight intervals of the Mulichinco Formation within the Sierra Chata Field in the Neuquén Basin have been ongoing. Because conventional high quality reservoirs were being developed in this field, a proper reservoir understanding and completion approach was applied. After developing these high permeability reservoirs, the operator began evaluating the tight intervals and new areas within the field, but a completely different approach was necessary to achieve motivating production improvement.An extensive study to help enhance reservoir understanding and identify key factors controlling productivity of these tight intervals (which tend to be in the range of 5 µD) has been ongoing. Some of the issues discussed in this study are 1) petrophysical review, 2) rock properties calibration, 3) geomechanics understanding, 4) faulting and micro faulting/lineaments description, 5) stimulation and completions review and, 6) understanding key production drivers.As in many other tight reservoir projects, a considerable area of the reservoir must be effectively stimulated during the hydraulic fracturing process to achieve economic productivity. Two critical issues hinder these objectives. First, the low permeability in addition to a pore pressure close to or even lower than hydrostatic are critical characteristics when attempting to flow back the well and clean up fractures. Second, very high horizontal stress anisotropy resulting from a strike slip stress regime promotes the generation of simple planar bi-wing fractures. It is well-known that this fracture geometry will contact much less reservoir area compared to more complex fractures, as the operator would normally intend to create at very low permeability reservoirs.This paper discusses these issues and how they were addressed. A pilot drilling and completion program was initiated during 2012 to validate this study. Key factors include well location relative to formation unconformities, their orientation relative to the far field principal stresses, hydraulic fractures generated, and overall completion design."

Jan 1, 2015

By J. A. Folinsbee, Andre Robitaille, Tony Y. Chong

"Conventional crushing and grinding is followed by gravity concentration to recover free milling gold. Refractory gold, finely disseminated within the pyrite and arsenopyrite matrix, is recovered by flotation followed by pressure oxidation, cyanidation, and cementation. Non-refractory gold is recovered by cyanidation/CIP processing.A comprehensive test program aimed at improving flotation recovery was initiated in June 1995. Plant testing indicated that flotation tails value could be significantly reduced using mechanical flotation cells. Based on these test results, a flotation circuit that incorporates one of the three existing flotation columns followed by mechanical scavenging and cleaning was developed. Detailed engineering was completed in September 1996. Construction started in February 1997 and was completed in 3 months at a cost of $3.2 million. An on-stream X-ray analyzer was installed to provide real-time arsenic and iron analyses and inferred sulphur value on some of the flotation streams.The new flotation circuit proved to be an instant success. Flotation tails values were reduced by 27%. Final tails solids and solution was reduced from 0.035 to 0 023, and 0.0014 to 0.0006 oz/ton Au, respectively. Based on a mill throughput of 1,620 stpd this decrease in tails value will result in an increased gold production of 7,500 ounces per year. The payback for the project is estimated to be around one year.This paper describes the evolution of the project from bench scale testing to commissioning. Also, the operational and economic impacts on down stream processing are highlighted"

Jan 1, 1998

By Phil Keele

"Manalta Coal Ltd. 's Vesta Mine will supply Alberta Power Limited's 740 MW Battle River Generating Station with 1 128 000 tonnes of sub-bituminous ""C"" coal in 1983. Mana/ta Coal Ltd. and Alberta Power Limited are in their seventh year of a 31-year coal supply agreement. With the exception of localized topographic highs where three coal seams are mined, the Vesta Mine is primarily a single-seam mining operation. Vesta's comprehensive programs of mine planning, preventative maintenance, reclamation, and employee relations make it an efficient and a well run operation. Introduction The Vesta Mine, located in east-central Alberta approximately 300 km northeast of Calgary, supplies sub-bituminous ""C"" coal to Alberta Power Limited's 740 MW Battle River Generating Station. The coal reserves and principal stripping equipment are owned by Alberta Power Limited. Manalta Coal Ltd. owns and operates the additional mining equipment and support facilities. Coal production is from a single pit, 3.5 km in length. Both single and multi-seam operations are encountered in the active pit. In 1983, production is anticipated to increase to I 128 000 tonnes from 906 000 tonnes in 1982. The additional tonnage will be achieved by operating 24 hours per day, 5 days per week. The following sections briefly highlight historical, geological and mining/reclamation aspects of the Vesta Mine. Figure I illustrates the location of the Vesta Mine in relation to the cities of Calgary and Edmonton. History Coal mining for domestic use began near the turn of the century in the Vesta Mine area. Initially, small underground room-and-pillar operations were dominant. As equipment technology advanced, surface strip mining replaced the underground methods."

Jan 1, 1985

By W G. Forbes

SOME 20 years ago, upon finishing second year at the University of Manitoba, I was faced with the choice of whether I wanted to be a geologist or a chemist. Accordingly, I sought out Professor Brownell, Head of the Department of Geology, to ask him what a geologist did. His reply contained the statement that following graduation one went out into the field in northern Canada for 5 to 15 years to reduce to practice what had been learned at university. To a young man, very socially conscious, even one year, let alone 5 to 10, in a small mining community sounded like being banished to a monastery in the Himalayas and thus I turned to chemistry. Moving to the present, last month I asked a geologist, and then a mining engineer, what does the fresh graduate in their field do these days? The reply was: usually serve an apprenticeship for an indeterminate period either underground or in the field learning the job.

Jan 1, 1965

By Z. X. Cui, X. D. Ma, L. Contreras, X. Jiang

The bath smelting process is one of the key techniques applied in the current copper smelting production, which includes bottom-blown and side-blown furnaces differently from the direction of gas injection. Liquid matte and slag form the bath in the smelting furnace. To better understand the fluid dynamic of the bath and further optimise the operational efficiencies in the smelting furnace, physical simulation of the bath in the horizontal cylindrical reactor was investigated. The mixing behaviour and wave motion of the bath in the bottom-blown and side-blown furnaces have been studied systematically. The mixing time is reduced with increasing gas flowrate and height of the lower layer, while it increases significantly with increasing the height of the upper layer. The wave motion in the furnaces can be suppressed with the presence of the upper layer, but the bath with a lower density generates higher wave amplitude. Overall, in comparison to bottom-blown mixing, side-blown mixing shows better mixing efficiency and lower wave amplitude. In addition, the plume eye and splash phenomena occurred in the bottom-blown furnace have also been studied. INTRODUCTION The bath smelting process is one of the principal techniques used in the current copper making industry. The bath smelting techniques have some advantages of high smelting efficiencies, low capital costs, low energy consumptions and reduced dust generations. From the direction of gas injection, the bath smelting techniques can be classified into five general types: (1) top-submerged blown, e.g. Ausmelt and Isasmelt; (2) top-suspended blown, such as Mitsubishi smelting; (3) top direct-to-copper smelting, such as Outokumpu smelting; (4) submerged side-blown, such as Noranda and Teniente smelting; (5) bottom-blown, such as Dongying Fangyuan bottom-blown copper smelting furnace (Schlesinger et al., 2002; Zhao, Cui, & Wang, 2013; Perez-Tello et al., 2018). In many metallurgical processes involving bath smelting situations, the objectives of agitation are to accelerate the bath homogenization inside the bath which makes a significant contribution to process efficiency and product quality. Extensive mixing studies have been performed for ladle refining and tundish associated to steelmaking processes through water physical models. Mixing time is the parameter used to quantify the efficiency of mixing in the liquid bath and the first empirical equation predicting mixing time was proposed by Nakanishi, Fujii and Szekely (1975). Later on, more systematic studies have been carried out on ladle mixing and researchers realized that the geometry of the vessel could also have a significant impact on mixing (Khajaviand & Barati, 2010). However, the investigations using ladles which are vertical cylindrical vessels, cannot be directly used in the study of mixing behaviour in horizontal cylindrical reactors. Understanding the fluid dynamics inside horizontal cylindrical bath smelter is useful from the industrial perspective. Recently fluid dynamics of horizontal cylindrical smelter related to copper smelting have been studied by the authors’ group (Shui et al., 2015a, 2015b, 2018a; 2018b; Xu et al., 2018, 2019).

Jan 1, 2019

By Horace Freeman

"IN THE writer's opinion, the most important industrial re-search problems in Canada concern development of technology for the treatment and commercial utilization of the recent discoveries of v.ast quantities of easily concentrated iron ores in both eastern and western Canada. They exist in both magnetite and hematite forms. The subject is doubly important because of the lack of metallurgical coking coal in Canada. Methods for utilizing our lower grade eastern and western coals for reduction purposes must be developed. We are fortunate in our supplies of oil and gas, which can supply the heat requirements for processing or for thermal electric plants, which are now competitive with hydro-electric plants in the industrial areas. These are among the reasons which have prompted the writer to continue the development of the co-current rotary kiln direct-reduction process outlined •in his report to this Institute at the 1956 Annual Meeting ( 1) in the face of the scepticism which has surrounded the numerous costly failures in 'sponge' or 'direct' iron production. The work involved in bringing the concentrating ores of Canada to the metallic state involves, firstly, concentration of the ores; secondly, preparing the concentrates for reduction; thirdly, reduction of the 'reconstructed' ore; and finally the steel making process. These briefly will be dealt with in order, giving emphasis to the most important of these steps, the reduction process which is the main subject of this paper."

Jan 1, 1959

By E. Thomson

This type of microscopic investigation, although still in its infancy, has already found practical applications in several different phases of mining activity. The study of the transparent minerals in rocks, by means of the ordinary petrographic microscope, has for long been a very useful supplement to observations in the field, but the opaque minerals, until recently, have had to rest content with a more or less superficial determination with the hand-lens or the blow-pipe. In a great many cases, particularly where the association of metallics has been somewhat complex, this has been entirely inadequate, and the determination of these opaque minerals under the micro- scope, has opened up a new field of scientific investigation that bids fair to surpass, in practical value at least, the micro-scopic determination of the rock-forming minerals. As the details of this kind of microscopy are possibly not entirely familiar to all mining men, it might be well to outline them very briefly before dealing with the practical directions in which this method may be applied. The ordinary petro-graphic microscope, with but one extra attachment, will serve for this work. A small reflecting device, called a vertical illuminator, is inserted immediately above the objective lens. This reflects the light down to the surface of the specimen and from here the light is directed up the middle of the microscope tube to the eye. As it is desirable that the maximum amount of reflection should be secured from the surface of the section, it is first polished and set in a position perpendicular to the vertical axis of the microscope.

Jan 1, 1924

By Mikael Ramström

The IREDES Special Interest Group (SIG) for Drill rigs has been active since its inception at MineExpo 2000, in Las Vegas USA. The SIG for drill rigs is responsible for the development of a IREDES Drill rig profile. This includes the exchange of production planning, performance and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During year 2001 a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies and third party suppliers and reviewed during several SIG meetings. In mid 2002 the profile was released for prototyping projects and since then, feed back received from these projects has been used as input to the first official IREDES release. LKAB and Atlas Copco decided in 2002 to start an IREDES prototyping project using the Simba L6C production drill rig as target equipment. The goal was to verify the drill rig profile and identify possible problems prior to the official release. This was done by implementing the IREDES prototype version in the LKAB?s production planning system and Simba rig control system. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this the mine production system was adapted for drill plan export and logging data import on IREDES format. This paper presents the most recent results of this prototyping project. Result from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES will be a central issue for future mine automation. As a result from this and other IREDES prototyping projects the official IREDES release will be available in 2003. Soon after that release IREDES compliant products can be expected. This will include drill rigs and mine production planning systems.

May 1, 2003

By D. B. Dreisinger, M. R. Tavakoli

"Vanadium has been produced from a variety of sources. This metal is known to make aqueous solutions of complex speciation as a function of vanadium concentration and pH. Considering the method of leaching, the impurities in the pregnant leach solution, and the planned vanadium product, different extractants and flowsheets can be applied for solution purification. This paper reviews the purification of vanadium leaching solution using organophosphorus, solvating, and amine extractants. This review focuses on vanadium separation from iron, molybdenum, and uranium, which are often present in vanadium resources such as primary ores, fly ashes, and spent catalysts.RÉSUMÉ Le vanadium est produit à partir de diverses sources. Ce métal est connu pour permettre des solutions aqueuses de spéciations complexes en fonction de la concentration du vanadium et du pH. En tenant compte de la méthode de lixiviation, des impuretés dans la solution mère de lixiviation et du produit de vanadium planifié, divers agents d’extraction et schémas de traitement peuvent être mis en oeuvre pour purifier la solution. Le présent article étudie la purification de la solution de lixiviation du vanadium au moyen d’extractants organophosphorés, solvants et aminés. L’étude cible la séparation du vanadium du fer, du molybdène et de l’uranium, lesquels sont souvent présents dans les ressources de vanadium telles que les minerais primaires, les cendres volantes et les catalyseurs usés."

Jan 1, 2016

By Franc R. Joubin

"Gold has been found in many parts of the Bridge River district of British Columbia; but it is from a relatively small area in the valley of Cadwallader creek that most production has come. The ore-bearing area measures 1/2 mile in width by 3 miles in length; and for convenience it is called the Cadwallader gold belt in this paper. In this belt are found the Bralorne and Pioneer mines and in addition several prospects under development.The gold of the Cadwallader gold belt occurs in quartz veins averaging about 3 feet in width and containing about ½ oz. of gold a ton. Except for a relatively small amount of silver, no other metals are produced from these veins. The ore-bearing veins occur in a variety of rocks. They occupy reverse faults and tension fractures belonging to a distinctive fracture system. Some of these structures are ore-bearing over lengths exceeding 5,000 feet and depths exceeding 3,700 feet. The production of the Bralorne mine (1932-1945) is 996,383 oz. gold and 190,709 oz. silver; that of the Pioneer mine (1930-1945) is 777,588 oz. gold and 135,698 oz. silver. These two mines have together distributed about $25,000,000 in dividends.The Bridge River district first attracted attention in 1863* when prospectors were attracted by its small but rich placer gold deposits. Most of the important lode deposits of the Cadwallader gold belt were discovered in 1897 (11). Many years of desultory development followed and it was not until 1928 and 1932 that the Pioneer and Bralorne mines, respectivdy, entered into profitable production."

Jan 1, 1954