Search Documents

By Barry J. Morash

The over-all slope angle of between 55 and 60 degrees at the Adams Mine necessitates control blasting on the final pit walls. The control blasting techniques used are pre-shearing and buffer blasting. Pre-shearing with 2'I2-inch holes on 5-foot centers is used in areas where jointing and rock type are not conducive to smooth stable walls. Buffer blasting with 12'/4-inch holes is used in areas where the rock is competent. Control blasting adds to the operating costs, but can result in substantial savings in increased slope angle and reduced stripping.

Jan 1, 1978

By Clifford S. Gibson

THESE troubled times suggest three reasons for maximum effort to control silicosis: (1) To keep to a minimum the ever-increasing burden occasioned by past deficiencies in this respect. (2) To effect the greatest production with maximum efficiency, which means at the least cost. (3) To preserve man-power in every way. Good control of the silicosis problem aids these aims. Inadequate control hampers all three. Insofar as our knowledge goes, silicosis in Ontario mines is caused by the inhalation of finely particulate quartz. It follows, therefore, that removal of dust containing this mineral automatically erases the cause. The achievement of this ideal is the aim of the mine operator. His best tool to this end is ventilation. This paper discusses mine ventilation from the viewpoint of dust control and it is hoped that in so doing there may result a better understanding of the part played by air in silicosis prevention. No attempt will be made to treat the subject fully. Instead, there will be presented certain salient aspects culled from field observations, the data in all cases referring to gold mines, unless mention to the contrary is made.

Jan 1, 1942

By K. R. Wood, G. W. McDonald

"The tailings disposal system at Les Mines Selbaie includes dewatering of tailings in a high-capacity thickener, followed by point discharge of the thickened solids to form a stable conical pile. Tailings water drains to ponds formed behind engineered dams, prior to either recycling f or process use or discharge to the environment. Design and economic considerations of the system are discussed. Construction, start-up and operating experiences are also presented.Introduction Les Mines Selbaie is located in the Abitibi region of northwestern Quebec, approximately 700 km north of Toronto and 150km south of James Bay. More locally, the Detour gold mine is 60 km to the west while the Noranda smelter is 220 km to the south.The deposit was discovered as a result of a Questor INPUT Mark VI geophysical survey in 1973, followed by diamond drill programs from 1974 to 1976. Three mineralized zones were delineated and underground exploration was carried out on all three. A production decision for the 'B-zone' copper-gold-silver orebody was made in July 1979. The underground operation started in July 1981, with full production of 1500 t/d being achieved in May 1982.During the planning phase, every effort was made to ensure that the operation would be environmentally sound . The design included the provisions of the then newly proposed provincial environmental guidelines. The tailings disposal system formed the most significant part of the environmental program due to the large volumes of solids and water effluent. In addition, the design allowed for future expansion of the system to accommodate mining of the other zones, thus minimizing future costs and disruptions."

Jan 1, 1986

By M. Pearson, L. Zunti

Pressure vessels in hydrometallurgy and many chemical process industries throughout the world require the use of specific lining systems to protect the parent vessel materials from corrosion and/or abrasion. Typically, these lining systems are required for processes that are corrosive and operate at elevated temperatures. Two basic lining system types arc: 1) refractory linings in conjunction with an impervious corrosion resistant membrane, and 2) metal-clad vessels consisting of titanium or other corrosion resistant metal bonded to a carbon steel shell. Operating conditions play a key role in selecting the type of lining system to be utilized for a specific application. Lining systems in turn have an impact on the process vessel size, which ultimately affects the capital cost of the vessel. The capital costs for each type of lining system must be considered for each application, as well as maintenance concerns, quality control, and delivery. It is clear that operating conditions play a key role in the final selection of lining systems utilized for specific projects based on initial capital cost, life-cycle maintenance costs, and overall service life. This paper will examine the fundamentals of each lining system, their inherent technical strengths and weaknesses, and present relative cost comparisons for each lining system as they apply to specific operating conditions and vessel sizes.

Jan 1, 2004

By H. Z. Liu, J. M. Zhao, F. C. Wang

"Novel silicate-alginate composite beads containing 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester (P507) were synthesized and applied for the adsorption of Nd3+ from aqueous solutions. The adsorption amount of Nd3+ has been increased owing to the introduction of P507. The effect of equilibrium pH (pHe), the kinetic and isotherm experiments were investigated. The adsorption reaches equilibrium at 9 h and the maximum uptake capacity is up to 195.4 mg/(g dry adsorbent). The Langmuir isotherm equations are used to describe the adsorption process. Complete desorption can be realized with 0.2 M HCl within 20 min. INTRODUCTIONRare earth elements (REEs) have found various applications in different domains, such as metallurgy industry, ceramic industry, nuclear fuel control, photo-electro-magnetic functional materials owing to their unique properties. Neodymium (Nd), as a representative of all of the most valuable REEs, is widely used as catalysts, laser crystals, capacitors, rubber additives, Nd-Fe-B magnets, hydrogen storage and so on. Thus, the separation and purification of neodymium is significant. Unfortunately, Nd always coexists with other REEs and selective separation of the individual Nd from the REEs mixtures is still extremely difficult owing to their strictly similar atomic structures and chemical properties.Liquid-liquid extraction (LLE) and solid-liquid adsorption (SLA) are the most widely adopted techniques for the separation of REEs in the hydrometallurgical fields. The LLE process is well suited for large-scale continuous operation because of its inherent high capacity and fast kinetics. Nowadays, as a commercial extractant, 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester (P507) has been extensively studied for extraction and separation of REEs since it has considerably good extractability and high separation efficiency (Xu et al., 1992). SLA is one of the effective and green separation methods with some prominent advantages, such as easy regeneration of adsorbents, small footprint size, less industrial wastes, higher enrichment factors and column efficiency,rapid solid–liquid separation without emulsion and so on. Hence, the introduction of extractants with excellent performance into adsorbents will integrate the advantages of LLE and SLA (Lee et al., 2009)."

Jan 1, 2012

By Charles S. Ney

"ZINC-LEAD REPLACEMENT deposits straddle the steep-sided valley of Kicking Horse River at a point three miles east of Field, B.c., in Yoho National Park. The Monarch orebodies extend into Mt. Stephen on the south side of the valley, and outcrop at two points, 1,000 and 1,200 feet above the valley floor. The Kicking Horse deposits are in Mt. Field, on the north side of the valley, and they outcrop 200 feet lower.The East Monarch outcrop is said to have been discovered in 1884 during construction of the Canadian Pacific Railway. The larger West Monarch outcrop, 700 feet west of the original discovery, was not reached till 1917 because of its nearly inaccessible location on the cliff face.The Kicking Horse mine was staked in 1906. Little development was done for several decades, and mining was not commenced till 1935.At the East Monarch, mining was commenced soon after location, and several thousand tons of ore were shipped prior to 1912. At this time a gravity concentrator was installed. This was operated till 1924, and a total of 42,000 tons of ore were mined, including about 10,000 tons from the West Monarch. The period from 1928 to 1935 featured flotation milling and the mining of 265,000 tons of ore, mostly from the West Monarch orebody. Intensive exploratory development was carried out in both Monarch and Kicking Horse from 1935 to 1946. Production from both mines in this period totalled 380,000 tons. From 1947 to the time of closure in 1952, considerable new ore was found in both mines and 185,000 tons were milled. Immediate possibilities for finding ore in the Monarch were considered exhausted. Kicking Horse orebodies are known to persist with a low grade of zinc. Total production from the two mines amounts to 842,500 tons grading approximately 7 per cent lead, 10 per cent zinc, and 1.2 ounces per ton silver."

Jan 1, 1949

By Damien Gaboury

"Two practical methods for correlating two or more diamond-drill core intersections, using a stereographic projection software are presented. The first may be used to establish if two or more vein intersections are correlative, based on their core angles and diamond-drillhole attitudes. The second method allows prediction of main vein attitudes from numerous intersections, based on a spherical density contouring projection. The methods are suitable for: (1) correlating veins in complex orebodies; (2) ascertaining lateral continuity of ore for reserve estimations; (3) demonstrating the hidden complexity of an orebody; and (4) correlating and interpreting various planar elements.IntroductionModern mineral exploration relies on diamond- drill core data and on the ability of geologists to interpret them. Drill core generally yields unoriented information, unless an expensive orientation device is used. As a consequence, strike and dip of planar elements such as lithological contacts or mineralized veins cannot be determined easily. This is particularly true for blind deposits (covered by thick overburden) and complex orebodies, where field data cannot support drilling interpretations. Such a problem has been addressed previously using two and three diamond drillholes and several solutions were proposed based on trigonometry, and geometric and stereographic projections (Mead, 1921; Wisser, 1932; Fischer, 1941; Stein, 1941; Bucher, 1943; Gilluly, 1944; Addie, 1962; Mills, 1963; Lyons, 1964). However, these solutions are time consuming and not relevant to present day computerized data plots."

Jan 1, 1997

By Vicken Aprahamian

"The Royal Canadian Mint (RCM) operates a gold and silver refining toll operation in Ottawa, Ontario, Canada. The silver refining line is a recent addition and was commissioned in 2005. One source of silver in the refinery is from gold doré which undergoes Miller chlorination before electrorefining to 99.99% cathode gold. Treatment of the Miller salt or silver-copper chloride produced consisted of a 2-stage high temperature reduction process step using soda ash prior to 2005. Copper-rich silver bars were produced and shipped offsite for further refining.The copper-rich bars could not be blended into sufficient high grade silver doré to dilute the copper and allow electrorefining in a silver nitrate medium. A new wet process was developed and commissioned to replace the high temperature reduction and allow removal of bulk copper. Thus upgraded impure silver produced was cast into anode for electrorefining to 99.9% purity silver flake. The 2005 RCM Hydromet Slag process is presented as well as its more current version. In addition, mention is made of a novel processing scenario for the introduction of Miller chlorination silver into the electrorefining circuit."

Jan 1, 2015

By Walter E. Montgomery

ACCIDENT-PREVENTION work in years gone by has been carried on by many mine managers as a philanthropic movement, but in recent years they have come to realise that Safety is good business and pays tangible dividends. Let us begin with the word itself. We are told that an accident is "any-thing occurring unexpectedly, undesignedly, or without known or assign-able cause'. It is further explained that it is any 'unpleasant or unfortunate occurrence involving injury, loss, suffering, or death", and, finally, "any unintentional or non-essential circumstance". We admit that accidents are unfortunate, unpleasant, unintentional, and they generally happen undesignedly and to a great degree unexpectedly, but to say that they happen "without known or assignable cause" leads us to believe that the word 'accident' is often misused. Would it not be more correct to say that a man suffered a "personal injury"? The word 'accident' in its proper sense implies something over which no one has any control, but when the majority of all so-called accidents are analysed we arrive at the incontestible fact that some act or action, previous or present, was the underlying cause. As long ago as the year 1556 this fact was mentioned by Georgius Agricola, who, in writing a paper on metallurgy, aptly stated, "It remains for me to speak on the ailments and accidents of mines, and of the methods by which they can guard against these, for we should always devote more care to maintaining our health, that we may freely perform the functions of our body, than to making profits". Farther on, Agricola relates in more detail, "Sometimes workmen slipping from ladders into the shafts break their arms, legs, or necks, or fall into the sumps and are drowned; often, indeed, the negligence of the foreman is to blame, for it is his special work both to fix the ladder so firmly to the timbers that they cannot break away, and to cover so securely with planks the sumps at the bottom of the shafts, that the planks cannot be moved nor the men fall into the water; wherefore the foreman must carefully execute his own work. Moreover, he must not set the entrance of the shaft-house toward the north wind, lest in winter the ladders freeze with cold, for when this happens the man's hands become stiff and slipping with cold, and cannot perform their office of holding. The men, too, must be careful that, even if none of these things happen, they do not fall from their own carelessness'.

Jan 1, 1938

By D. M. Maijer, S. M. Mohseni, A. B. Phillion

The microstructure evolution kinetics of aluminum alloy B206 during artificial aging has been investigated using non-isothermal calorimetry. A combination of differential-scanning calorimetry (DSC) and tensile tests have been utilized to develop an Avrami model to predict the precipitation kinetics as a function of the thermal processing parameters. The Avrami coefficients, found based on a Kissinger analysis, compare well against those reported in the literature for aluminum-copper alloys. The rapid precipitation kinetics predicted by the Avrami model at temperatures higher than 200°C were assessed through a qualitative comparison against hardness measurement results. In contrast to the continuous hardening observed at 150°C, the material softens with continuing heat treatment at 250°C resulting in an overaged state. This can be attributed to the rapid precipitation kinetics at this temperature, leading to the termination of the precipitation-hardening effects at early stages of artificial aging.

Jan 1, 2015

By G. D. Garland

"IntroductionALTHOUGH the presence of rock salt in the Carboniferous basin of northern Nova Scotia has been known for at least one hundred and twenty years, and salt has been mined at Malagash continuously since 1919, certain characteristics of the deposits make exploration by drilling or surface examination difficult. The surface rocks of the basin are, in general, of Pennsylvanian age, while the salt occurs in the Mississippian Windsor group. The latter rocks are brought to the surface only along anticlinal folds, or as irregular fault blocks. Because of the limited areal extent of these Windsor exposures, and their complicated internal structure, geophysical surveys, especially gravimetric, can be of considerable aid in outlining the more favourable areas.The present paper describes the results of recent investigations by the Dominion Observatory, in cooperation with the Nova Scotia Department of Mines. It includes a regional study of that section of the Cumberland basin lying between Springhill and Malagash ( Figure 1), and a much more detailed survey of the immediate vicinity of the Malagash deposit itself. This deposit had been studied by Miller (6, 7) with the torsion balance nearly twenty years before, and a direct comparison between the results given by the two types of instruments is therefore possible."

Jan 1, 1955

By J. C. Li, Y. Zou, L. He

"The effect of rock joints is significant in characterizing dynamic behaviors of discontinuous rock masses. To reveal the relation between the transmission coefficient and the contact situation of the joint surface, an experimental study on stress wave propagation across an artificial rock joint was carried out using a modified Split Hopkinson Pressure Bar (SHPB) apparatus. All the bars and specimens were norite cored from the same site, and one surface of the specimen which contacted to the transmitted bar was sawn with a number of notches to simulate the artificial rough joint. According to a wave separation method, two strain gauges were mounted on each pressure bar at a specific spacing, then the incident, reflected and transmitted waves across the joints were obtained from the test data. It was found that the contact situation of the rock joint surface makes a different on the wave propagation. Finally comparisons of the transmission coefficients with different contact area ratios and different joint thicknesses were made respectively. The results show the effects of contact area ratio and thickness of joints on wave transmission.INTRODUCTIONJoints affect the dynamic mechanical behaviors of the rock masses significantly. When propagates across the rock masses, wave usually attenuates in amplitude and frequency due to the presence of the joint as a discontinuous interface in the rock masses. Rock joints are the main factor that affects the behaviors and properties of rock masses. Many researchers have focused on the mechanical properties of rock joints under quasi-static conditions. Nowadays, the effect of joint dynamic properties on wave propagation across rock masses is gradually taken into account in theoretical and numerical studies.The effective contact area, joint roughness, and properties of the asperities and filling materials have been found to influence the normal stiffness of joints (Bandis et al. 1983). As suggested by the International Society for Rock Mechanics (ISRM), the roughness of the discontinuities can be generally characterized by large-scale “waviness” and small-scale “unevenness” (Brown 1981). Many researchers focused on the roughness of rock joints that affects the mechanical properties of rock masses and wave propagation. For example, Brown and Scholz (1985, 1986) presented theoretically and verified experimentally a closure model of contact between two random nominally flat elastic surfaces, which showed that the joint closure property depended both on the surface topography and material properties. Pyrak-Nolte et al. (1997) presented the quantitative aperture data for three-dimensional interconnected fracture networks, which were imbedded in intact opaque rock samples several centimeters in length, using x-ray computerized tomographic (CT) imaging. Fardin et al. (2001) systematically investigated the effect of scale on the surface roughness of rock joints and concluded that samples should be equal to or larger than the stationary limit for surface roughness to be accurately characterized on a laboratory scale or in the field. Zhao et al. (2006) conducted excellent ultrasonic tests across intact cement mortar specimens, singlefracture specimens, and two-fracture specimens."

Jan 1, 2015

By L. K. Smith, C. R. May, K. R. Schrag, H. Buchwald

"New contracts for 65 million long tons of coking coal valued at over $900 million, over the next 15 years, herald the rebirth of Alberta's coal industry. The industry is optimistic that export orders may reach 20 million tons per annum by the mid-1970's. Coal will be extracted from underground and surface mines and it is expected that the total labour force will double from the present 1,200 men within the next two years. Ali the health hazards associated with coal mining are likely to be encountered and it will be incombent on the Provincial Department of Health to specify the standards which relate to health and environment where no such standards have previously existed. This paper examines some of the problems which are being encountered in setting up an environmental health program and reviews the practicability of environmental monitoring methods, with special reference to respirable dust."

Jan 1, 1969

By W. J. Kuit

Since closure in 1968, the Wedge Mine, situated adjacent to the Nepisiguit River in New Brunswick, has been flooding with acidic water containing toxic levels of heavy metals. Cominco Ltd. has undertaken a series of pollution control measures to mitigate the threat posed to the river quality. Included has been a successful treatment campaign in 1976 which discharged in excess of 30 million gallons of high-quality effluent from the accumulated volume of mine water. The sources of contamination have been identified as actively leaching waste dumps. A comprehensive program of permanent corrective measures has been prepared which will culminate in mine backfilling. Once completed, the unacceptable burden of water treatment in perpetuity at a non-producing property will be removed.

Jan 1, 1977

Project Details ? Located 420 km northeast of Yellowknife, Northwest Territories ? Jericho kimberlite discovered in 1995 ? Feasibility study showed +3,000,000 carats recovered from 2.6 million tonne reserve ? Nine year mine life ? Approx. 100 person workforce in full production ? First mine for Tahera, First new mine for Nunavut Completed Ambitious Construction Schedule During 2005 o Feb ? Mar/05 Winter road mobilization o Mar ? Dec/05 Pre-stripping, earthworks o Mar ? Apr/05 Camp facility, occupied May 3 o May ? Dec/05 Process plant o Jun ? Dec/05 Maint. shop, fuel storage, power plant o Jan ? Mar/06 Commissioning, start-up o April 2006* COMMERCIAL PRODUCTION

May 1, 2006

By M. J. Collins

The Advocate Mines Limited asbestos property is 6 km north of Baie Ve rte on the northeast coast of Newfoundland. Mining began in the early 1960s and was concluded in 1981. The chrysotile asbestos deposit lies at the north end of the Baie Verte Lineament, the interface between a closing ocean floor and continental margin. Asbestos occurs within ultramafic rocks of abducted ophiolite massifs that were thrust westward against Fleur-de-Lys Supergroup metasediments (continental rise sediments) in the Lower to Middle Ordovician. The asbestos-bearing ultramafics belong to the Central Ultrabasic Sequence of the Advocate Complex. Serpentinized peridotite of this sequence has a 'waste cap' core that grades outward to increasingly sheared rock. Asbestos is found mainly in a northtrending, basin-shaped zone surrounding the core, specifically within fractured serpentinized peridotite that abuts the sheared rock. Asbestos appears as stockworks of chrysotile cross fibre veins and is concentrated between brown, narrow brucitic dunite dykes and sills. Shear contacts commonly surround the ultrabasic body. Cross faults and complex Jointing also exist. The Advocate Mines Limited mill produced 65,000 tonnes of Group IV fibres and 1 l , 000 tonnes of Group VJ fibres annually. The bagged product enjoyed markets worldwide.

Jan 1, 1984

By Christopher Riley

A relatively unexplored lead zinc deposit lies about 12 miles northwest of Revelstoke, B.C., in the highly metamorphosed Monashee Group of rocks of the Shuswap Terrane, Precambrian in age. Host rocks are of sedimentary origin and consist of gneisses, schists, marbles and quartzites with intermediary types. The marbles and quartzites provide good horizon markers. Using these it is possible to interpret the controlling structure which is a syncline overturned to the north, dipping south at about 45°, and plunging east at about 12°. The syncline is truncated at about halfway of its length on a peak on the west side of which a partial cross section together with superimposed minor folds may be seen. The quartzites and the two marble beds may be traced over much of the structure. There are two lodes, above the marble and below the quartzite, which converge eastward and which are the exposed edges of the same host bed -an impure limestone.

Jan 1, 1961

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By Keith Spence

"The notion of ""value"" has always been a subjective and contentious issue. Indeed, Value is in the eye of the beholder. There are varied methods and practices for valuing property, as there are industries in which they are applied. For example, there are ""replacement value"", ""insurance value, ""salvage value"", ""appraised value"", ""book value"" and ""fair market value"", to name a few, although in the mining industry, valuations usually refer to fair market value.In the Canadian mining industry, at present, there are no comprehensive regulations or guidelines that specify which approaches or methods are appropriate for use in the valuation of mineral projects. In January 1999, The Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. Among the approaches to be considered, are included the following: the Discounted Cash Flow Approach, the Cost Approach, the Option Pricing Approach and Market Comparables Approach. In addition, methodologies differ depending on whether the project is at the exploration stage or the producing stage.The CIMVal committee expects that its final report will form the basis for a standard Canadian Code for the valuation of mineral properties."

Jan 1, 2003

By J. J. Fitzpatrick

"This paper deals with the methods used by Quebec Cartier Mining Company in the evaluation and selection of new haulage equipment and in increasing the productivity of the existing fleet.Selection of new equipment is based upon the comparison, for each model under consideration, of the capital investment required and the estimated operating costs and production rate. The calculation of the production rate is based on a widely used estimating procedure. Actual operating conditions considered in the method include: payload, haul distance, road grade, rolling resistance, loading and dumping times, and operational efficiency. A digital computer is used to handle the large volume of repetitive calculations required. Where a fleet of haulage equipment includes trucks of different size and performance characteristics, the problem exists of assigning each truck type to the different working locations to minimize total cost. Linear programming can be used in the solution of this problem."

Jan 1, 1967