Search Documents

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By D. G. Tisdale, W. Curlook, J. M. Toguri

"In this study, the vapour phase reduction of titanium tetrachloride conforms to the traditional Kroll chemistry, but employs argon as an inert carrier gas and requires a higher reaction temperature of 1150°C to 1250°C. A vapour phase reaction is advantageous because titanium is the only condensed phase present, and the metal can be collected free of magnesium or magnesium chloride, in marked contrast to the titanium sponge produced by the conventional Kroll process. The yield of metallic titanium from the reaction was determined as magnesium additions ranged from 36% to 168% of the stoichiometric requirement. Yields of over 99% were obtained when an excess of magnesium was present. Although the collection efficiency was low, metallic titanium was collected at the reaction site, where all other species were present as vapours. Magnesium and chlorine concentrations in the collected titanium were less than 0.3%.IntroductionA proposed method (Curlook, 1987) for titanium production has been investigated as an alternative to the conventional Kroll process (Kroll, 1940). The advantages of the new process include a simplified means of recovering the product metal, and a potential for lower overall energy consumption and greater product purity. A higher reaction temperature for the reduction of titanium tetrachloride results in a vapour phase reaction, rather than the conventional liquid phase reaction. This is the major conceptual difference between the proposed and the established (Kroll) processes.This study focussed on optimization of the process chemistry and briefly examined the issue of product deposition and collection. The reduction of titanium tetrachloride with magnesium, to produce metallic titanium and gaseous magnesium chloride:"

Jan 1, 1997

By D. W. Hayley

The rapid expansion of exploration drilling with anticipated production facilities for oil and gas in the Mackenzie Delta region of the Northwest Territories has created a demand for granular construction materials. This paper discusses the technique adopted and experience gained by the authors from several major resource evaluation programs in this remote area. The first part of the paper describes a methodology for deposit identification, logistics of helicopter and ground-based drilling operations and the sampling difficulties which are unique to permafrost: soils. The second part describes the exploitation of a large glaciofluvial deposit at YaYa Lake on Richards Island. Granular construction material is sparse in the delta region relative to projected demand. Exploitable sources of granular materials for aggregates or construction borrow are found in glaciofluvial deposits of Pleistocene age or in outcrops of Paleozoic bedrock. Glaciofluvial landforms can be located by reference to published surficial geology maps coupled with airphoto interpretation. Preliminary assessment of these features in a large region is most economically carried out during the summer months with a drill that is transportable by helicopter. Once prospective borrow pit sites are identified, a detailed ground-based winter drilling program must be undertaken to establish aggregate quality and quantity, and to provide information on natural features which could affect development. The glaciofluvial terrain has been highly modified by the formation of massive ground ice within the gravel deposits. This presents some unique pit development problems which are not encountered in a normal bedrock quarry operation.

Jan 1, 1977

By Paolo Farina

Slope monitoring radar has emerged in the last ten years as a leading edge tool for monitoring movements in natural and engineered slopes, thanks to its ability to rapidly measure slope movements with millimetric accuracy over wide areas in any weather conditions, obviating the need to install artificial reflectors. In recent years, slope monitoring radar has experienced significant improvements in its performances, mainly thanks to the use of different radar technology, such as Synthetic Aperture Radar (SAR), able to overcome some of the limitations of the first generation of radar and to provide higher spatial resolution, longer working distances and faster acquisition time. One of the leading applications of this technology is today represented by slope monitoring within the surface mining industry. Prominent international mining groups currently employ slope monitoring radar, based either on Real Aperture Radar (RAR) and SAR technology, for active and background monitoring of open-pit walls. The main technical features of typical slope monitoring radar based on SAR technology along with their possible applications are presented in this paper along with recent case studies of successful slope monitoring in open pit mines.

Jun 1, 2012

By Graham Walker

A new Code of Practice for the brake performance of off -highway vehicles was established in Alberta in 1976. Vehicles loaded to gross vehicle weight must be capable of stopping with mechanical brakes five times in quick succession on a grade of 10 per cent from a speed of 28 miles per hour. Comparative trials of various brake systems have been carried out and some combinations capable of meeting the Code are identified. Some problem areas in truck braking are reviewed and potential developments indicated.

Jan 1, 1977

"Dry crushing trials at pilot scale have shown that the IMPTEC Super-fine Crusher has the capacity to generate ultra-fine products from hard mineral assemblages presenting at either coarse or fine feed sizes. The super-fine crusher was introduced at the 27th International Mineral Processing Congress in Santiago Chile, with results from a range of duties, which demonstrated the crusher’s potentially expansive operating scope. This paper focuses on current preparations to progress the technology from pilot scale to commercial scale within a concrete production plant, where lead blast furnace slag will be crushed to ultrafine sizes to generate an active silica product for use as a supplementary cementitious material, which can replace Ordinary Portland Cement. A key objective of the operation is to demonstrate an economical route to reducing the cost of concrete production, improving concrete quality and reducing greenhouse gas emissions. The paper also highlights the potentially key contribution super-fine crushing can make to the long-term viability of iron ore beneficiation by simplifying comminution flow-sheets and reducing operating costs. There is every indication that the technology has the potential to feature universally in metalliferous and industrial mineral flow-sheets. INTRODUCTIONToday’s IMPTEC super-fine crusher is the successful end product of development work over 19 years and is the third particle size reduction device conceived, built and tested over that time. The concept evolved as engineering design progressively developed a mechanism capable of harnessing a highly efficient combination of fundamental particle breakage mechanisms. Early development trials at pilot scale indicated that super-fine crushing had the potential to establish a wet or dry, media free, low energy route to ultra- fine products from hard mineral assemblages. Having achieved some impressive results from open circuit pilot tests on fly ash and granulated blast furnace slag it became clear that the cement industry may well provide opportunities to apply the technology commercially. Following expressions of interest from local cement and concrete plant operators, IMPTEC negotiated an agreement to undertake commercial trials with a SFC 350 super-fine crusher installed on site at a concrete supply plant in South Australia. Super-fine crushing scope was recently expanded following further expressions of interest from research groups involved in the processing of iron ores. Pilot trials are progressing in these areas."

Jan 1, 2016

By Bradford P. Simser

The theoretical capacity of various ground support components can be misleading, especially in bursting ground where the failure mode is often in the retainment system. Wire mesh screen seams often peel open rather than breaking the wire strands, fractured rock often un-ravels around the bolts rather than breaking the bars. If a weak link(s) in the system fails prematurely, then the potential capacity of the system may never be fully realized. Underground observations are used to show how some support systems behave in the field. Various combinations of wire mesh screen with friction bolts, rebar, modified conebolts, cablebolts, shotcrete and mechanical rockbolts are considered. A short case history is used to contrast the performance of ?just-intime? development in a high stress faulted area versus a tunnel subjected to multiple stress changes in a similar environment. The latter proved to be a serious ground support problem when the well developed fracture zone around the opening was subjected to dynamic loading from a large seismic event causing a severe rockburst. In such cases an improved mining strategy may be more relevant than higher capacity support systems.

Feb 1, 2008

By J. Y. Liu

In Comparison to the application of HPGR (high-pressure grinding rolls) in the cement industry and in iron ore processing, the introduction of this energy-efficient comminution technology to processing of nonferrous base-metal ores has progressed slowly as yet. In the field of minerals industry, challenges lies not only in the large variety of the feed material with respect to particle size, density, hardness, moisture and mineralogy of the material but also in complexity of the processing flowsheet, which need to be addressed from case to case based on result of HPGR comminution test work. Whereas conventional comminution test with HPGR in lab-scale or pilot scale needs quite a large amount of feed material, a compressive stressing test of particle-bed in piston-die device provides an effective way to study interparticle breakage behavior of ore material with much less feed. In the present study the effects of interparticle breakage on comminution of a copper ore has been investigated by compressive stressing of particle bed in a piston-die device. The feeds to the particle-bed stressing tests were four narrow size fractions in the size range of 0.3~3.35 mm and a broad size fraction of 0/3.35 mm. The pressures applied were in the range between 30 and 180 MPa. The results showed that the specific energy consumption increases linearly with the pressure; the product fineness increases also with the pressure, but the magnitude of this increase declines as the pressure goes up. Under the same stressing intensity, the product size distribution curve becomes steeper as the particle size decreases, so there is no self-similarity between product size distributions of different feed sizes. The suitability of a material-characterization model for interparticle breakage was verified for this ore. In addition, the effect of interparticle breakage on comminution of this ore with respect to its influence on the downstream flotation were analyzed in terms of size-metal distribution and mineral liberation.

Jan 1, 2016

By E. V. Manlapig, M. A. Hampton, M. E. Holuszko

Methanol treatment of ZnS particles has been found to remove slimes and facilitate flotation. The removal of slimes renders the ZnS surface more hydrophobic, resulting in an increase in the hydrophobic attractive force between the particle and bubble. Hallimond tube flotation, induction time measurement and particle-bubble force analysis with the atomic force microscope (AFM) was undertaken to link the beneficial effect of methanol treatment of ZnS particles to their increased floatability.

Jan 1, 2009

By F. Ford, Z. Dai, A. W. Lee

ABSTRACT: As high-grade nickel sulphide ores are being depleted and processing laterite ores continues to pose challenges, the future of nickel extraction lies in low-grade ultramafic ores. Canada has large resources of low-grade ultramafic nickel sulphide ores in the Thompson Nickel Belt. Most of the deposits are high tonnage and open pittable, but have high MgO content. The main challenge in processing low-grade ultramafic ores is the presence of serpentine. Chrysotile, one of the three polymorphs of serpentine, is the most common form of asbestos. In addition, the high slurry viscosity associated with ultramafic ores makes grinding and flotation possible only at a very low solids percentage.

Jan 1, 2011

By K. Webb

At both the international and country level, the issue of how the mining sector and indigenous populations should engage on issues of mutual interest or concern has emerged as one of central importance and controversy; involving the mining industry, Aboriginal communities, governments, the courts, and other stakeholders. At its heart, stakeholder engagement is an ethical issue, although it manifests itself in international instruments, domestic laws, industry guidance and agreements. At the international level, the concept of ?free, prior and informed consent? (FPIC), while not subject to widespread agreement on the finer details of evolving definitions, seems to be emerging as an increasingly recognized engagement norm. Within Canada, through a series of decisions, the Supreme Court of Canada (SCC) has articulated a fiduciary obligation of the Crown to consult with and accommodate impacted Aboriginal groups on resource management issues. Provincial governments have been variously attempting to adjust their resource management regimes to stay in alignment with SCC and lower court decisions. Mining sector organizations, working with First Nations partners, have developed agreements to work together for mutual benefit. At the individual mine and community level, there have been instances of constructive engagement, as well situations of physical resistance and legal challenges. The purpose of this paper is to examine the potential impact of new rules under the Ontario Mining Act introduced in 2012 and taking full effect in 2013, which amongst other procedural specifications, addresses the issue of mining industry-Aboriginal consultation in exploration and development activities. Leading up to the passage of the regulations, representatives from some junior mineral exploration companies have been highly critical of the new rules. Similarly, there have been a range of responses to the new rules from some in the First Nations community. The paper will review the regulation in terms of its apparent alignment with SCC decisions and the international norm, compare the regulations with existing mining sector organization guidance documents, and it will draw on the stated perspectives and commentaries of First Nations communities, mining firms, governments, nongovernmental organizations, and others. Building on the foregoing, the paper will provide a preliminary analysis of the perspectives and potential impacts of the new regulation on various stakeholders, and on that basis, possible avenues for further consideration will be suggested.

Aug 1, 2013

By M. H. Leite, R. Corthésy, D. E. Gill

"La connaissance des contraintes naturelles qui prévalent dans les massifs rocheux est un prérequis indispensable pour la conception sécuritaire et économique des excavations comme on en retrouve dans les exploitations minières souterraines. Certains chercheurs se sont attardés à colliger les résultats de mesures de ces contraintes et les ont utilisés pour produire des modèles de prédiction basés sur leur traitement statistique. Ces modèles de prédiction sont très populaires auprès des exploitants miniers puisqu’ils permettent, du moins dans les étapes préliminaires de design, d’obtenir de façon s’apéconomique mais approximative, une partie des paramètres dont ils ont besoin. Dans le cadre d’un projet initié en 1994 avec la collaboration de l’IRSST, il a été décidé de produire un modèle de prédiction englobant une partie de la zone périphérique de la faille de Cadillac, soit une zone plus restreinte que le Bouclier Canadien utilisé jusqu’ici comme région pour l’élaboration de tels modèles. Pour produire ce modèle de nouvelles données obtenues avec une technique permettant d’exercer un excellent contrôle de qualité ont été ajoutées à celles déjà disponibles. Une telle régionalisation des données de base permet d’obtenir un modèle où les intensités et les orientations des contraintes principales sont beaucoup moins dispersées que ce que rapportent les modèles publiés jusqu’à ce jour. Enfin, il est démontré que le modèle proposé pour la région étudiée est en toute probabilité plus sécuritaire que les modèles plus généraux publiés à ce jour. Knowledge of the in situ state of stress existing in a rock mass is essential to the safe and economical design of underground mining excavations. Prediction models have been published, based on the statistical treatment of stress measurement results. Such prediction models are very popular among mine operators because they allow them, at least at a preliminary design stage, to economically obtain part of the information needed, even if this information is approximative. In 1994, a research project financed by IRSST was initiated aiming to produce a prediction model that would comprise a peripheral zone around the Cadillac fault. This region is more confined than the Canadian Shield on which the existing prediction models have been based up to now. In order to produce such a model, existing stress measurement results have been used in conjunction with new stress measurements that have been performed based on a technique which allows full control of the quality of the measurements. Restricting the data upon which the model is based to a more specific region gives a model in which the intensities and the orientations of principal stresses are far less scattered than the results published to date. Finally, it is shown that the proposed model is probably safer for the studied region than the models previously published."

Jan 1, 1998

The negative effects of pyrite and pyrrhotite on thiosulfate gold leaching have been investigated. Possible remedies to reduce some problems are discussed. In a gold bearing pure silicate ore, 92% of gold could be extracted within 3 hours using a solution containing 0.2 mol/L ammonium thiosulfate, 0.9 mol/L ammonia, 30 - 300 ppm copper sulfate and 8.6 ppm dissolved oxygen at pH 10.26. The thiosulfate consumption was 7.1 kg/t under these conditions and could be further reduced to 3.5 kg/t by decreasing the dissolved oxygen to 0.3 ppm. Addition of 16% pyrrhotite or pyrite into the silicate slurry led to a decrease in gold extraction by 2% or 9% respectively and an increase of thiosulfate consumption by 11 kg/t or12.8 kg/t respectively in three hours. Several adjustments, such as increasing copper ion and ammonia concentration and reducing the dissolved oxygen level to 0.3 ppm resulted in increased gold extraction and lower thiosulfate consumption despite the presence of these sulfides.

Jan 1, 2005

By K. Schimann, H. D. Knipping, J. P. Fouques

"The Cigar Lake uranium deposit, in the Athabasca area of north Saskatchewan, was discovered in May 1981 by Cogema (Canada) Ltd., as operator of the Waterbury Lake Joint Venture.The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sandstone, at a depth of 410 m to 450 m below surface.At the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25m and 105m. It has the shape of flat-lying /em 5 m to 30m thick and shows a remarkable longitudinal and lateral continuity from the information obtained to date. A well defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west trending structure within which a particular rock facies (""augen gneiss'') has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-AI rich clay minerals (illite-chlorite). The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfa-arsenides of nickel and cobalt. Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and although no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, there may be locally a good coincidence.However, a combination of several methods proved extremely useful in interpreting the regional geology and defining the drilling targets within the favourable areas.Although the Cigar Lake deposit shows many similarities with several classical deposits of the Athabasca region, it is characterized by the intensity of its alteration processes and the presence of massive, extremely high grade mineralization.At the end of 1984, the global geological reserves estimated by geostatistics on the main mineralized ""pod"" of the deposit amounted to 110,000 metric tonnes of uranium at an average grade of 12.2% U, with a precision of 25% at the 95% confidence level."

Jan 1, 1986

By K. W. Fritzsche

The prosperity of any nation depends, to a large extent, on its natural resources such as oil, coal, 'metal, timber, waterpower, and fertile soil. Each one of these resources forms the basis of a huge industry. The mining and smelting industry ranks among the first since it paves the way for a number of other industries. The mines and smelters provide a market for electric power, coal, timber, and agricultural products: other industries in turn provide a market for metals and non-metals. The real pioneering, however, is done by the prospector who goes into the wilderness to search for the ores from which the metals are to be extracted for the use of men. Prospecting is an interesting and fascinating occupation. There are many difficulties and hardships in the way but the lure of gold and the vision of finding an outcrop that may develop into a large bank account, within a reasonably short time, will urge the prospector forward. Thus, on the outskirts of this northern hemisphere hundreds of prospectors are searching and toiling and of whom nothing is known or heard until they reach civilization and announce a new discovery. Then a mad rush takes place and everybody who can afford to go will take a gamblers chance and plant stakes in the neighbourhood of the new discovery, or wherever an outcrop of mineralized rock can be found, with the hope of winning a fortune.

Jan 1, 1925

By John L. Bonus

"WITHIN THE BROAD PARAMETERS implied by the title of my speech, I propose to deal more particularly this evening with a subject the many aspects of which have constituted the essential elements of one of the main thrusts undertaken by the MAC in the past two years, i.e., to create among Canadians a much greater awareness of the importance of mining and to demonstrate to them what are the many and varied benefits they derive from mining activities across their country. In other words, MINING - WHAT IT MEANS TO CANADA.I also intend to discuss some aspects of government-industry relationships.I am very conscious of the fact that I am speaking to an audience made u in large part of experts in several fields of mining and exploration activities. They will be familiar with many of the points I intend to discuss. However, without in any way suggesting that familiarity breeds contempt, might I emphasize that even in this particular forum there is justification for reiterating some of our basic philosophies and suggesting ways whereby they might be better understood and promoted.Let us first summarize the present dimensions of the Canadian mining industry."

Jan 1, 1971

By B. K. Gorain

Barrick' s Buzwagi copper-gold deposit in Tanzania comprises oxide, saprock and sulphide mineralized zones averaging approximately 0.058oz/t gold, 0.13% total copper and 0.03% cyanide-soluble copper. A comparative evaluation of the project based on two potential flowsheet alternatives is presented. The first flowsheet included a gravityconcentration and carbon-in-leach (CIL) plant. The second flowsheet was based on a Gravity-Flotation-CIL plant, which proved to be more economically robust. Selective flotation of copper minerals to produce a saleable copper concentrate proved to be challenging. Detailed characterization of the Buzwagi deposit was carried out through understanding of ore mineralogy, mineral liberation, floatability and selectivity, reagent chemistry and regrinding issues. With this insight, a flotation concentrate of greater than 25% Cu was achieved, recovering a significant amount of copper minerals and tellurides. The overall economics of the project improved significantly with the addition of flotation. Leach tests on gravity and flotation tailings showed an overall increase in gold recovery of approximately 6% for a Gravity-Flotation-CIL plant compared to that for a Gravity-CIL plant.

Jan 1, 2007

By K. Shen, A. J. Sinclair, N. Champigny

"Fluid inclusion studies from the Cinola deposit indicate low salinities and low C01 contents of the ore fluid. This supports a suggestion that the mineralizing fluids originated from pore water in the fluviatile host rock (mid-Miocene Skonun Formation). Bimodal distribution of filling temperatures suggests the existence of at least two temperature regimes centred on 160°C and 270°C during mineral deposition. Independent age and stratigraphic evidence indicates that depth of mineralization is between 1.1 and 1. 8 km, corresponding to a hydrostatic load of between 110 and 170 bars.RESUMELes donnees sur les inclusions fluides du gisement Cinola indiquent de basses salinites et basses teneurs en C01 . Ceci confirme que les fluides mineralisants ont ete derives de l'eau interstitielle prise dans les sedimentsfluviatiles hates. La distribution bimodale des temperatures d'homogenisation implique !'existence de deux regimes de temperature concentrees vers 160°C et 270°C pendant Ia mineralisation. La profondeur alaquelle le gisement s'est forme est evaluee d'etre entre 1.1 et 1.8 km a partir d'informations stratigraphiques independantes: ceci correspond a des pressions hydrostatiques de 110 a 170 bars."

Jan 1, 1982

By Jason Palmer

"Water in mining is the commodity that has driven the mining industry for decades. Often used frivolously, modern economic and social pressures are forcing change to use less water and to improve the quality of water and effluents. Used in many processes, water is ultimately consumed in tailings disposal and technologies which can increase the recovery of water are constantly being developed. Filtration and thickening are often seen as competing technologies for water recovery however new cases are developing that show significant advantages can be achieved by combining the two technologies to develop the most effective solution. Supported by case studies this paper investigates the merits of each of the technologies and which strategies of combining the two produce the best outcomes.INTRODUCTIONMineral processing applications generally require water for the processing of ores, whether utilising physical or chemical methods. Water is first added in the milling stage and additional water added as required throughout the circuit. Water losses from the circuit are principally associated with the tailings stream. Optimised water recovery is necessary both because it is a scarce commodity and to minimise the environmental impact.Water recovery is usually accomplished through a sedimentation or filtration processes. Water can be removed from the tailings impoundment by evaporation but this does not improve the mine’s water consumption. The water recovery methodology also determines the water quality; increasing water recovery concentrates solutes in the process water and may create recirculating loads of fine solids."

Jan 1, 2016

By Wei Wang

The SMCO copper plant is located in DR Congo, and was designed by China NERIN Engineering Co., Ltd. The process is a typical hydrometallurgical plant with Leach-SX-EW, with the project treating the oxide minerals with agitation leaching, followed with three stage of solvent extraction and two stages of stripping, and using permanent SS cathodes to produce LME grade copper. Because of the special characteristic of the ore, what contains 2 different type of oxides (one high carbonate oxide and the other low carbonate), there are several new technical measures that have been developed and adopted for the plant. For example, different grinding, leaching, and filtering are used to treat different oxides. This paper, presents the project process, engineering design, construction and commissioning. The paper also describes some of the problems encountered during plant commissioning, such as the agitation leaching tank issues, and corrosion in the settler-mixer. This paper discusses some NERIN solutions to these problems, and explains the use of the CN filter, which is used to filter PLS to treat high level suspend solids, instead of the traditional sand filter. Finally, this paper also proposes steps / measures for further improvement for future plant operation.

Jan 1, 2014