Search Documents

By D. B. Dreisinger, D. G. Dixon, G. Nazari

"The kinetics of chalcopyrite leaching in acidic ferric/ferrous sulfate media under atmospheric conditions in the presence of pyrite has been investigated. It has been found that pyrite samples from different sources affect the rate of chalcopyrite leaching differently. A strong correlation between the amount of silver associated with the pyrite and its effectiveness has been noted. In this study, improvement of the catalytic properties of pyrite such that all pyrite samples accelerate the rate of copper extraction regardless of their sources is demonstrated, and a detailed discussion of the mechanisms involved in the process of chalcopyrite leaching in the presence of silverenhanced pyrite is presented. INTRODUCTIONIt is well known that chalcopyrite resists leaching in sulfate media. It has been proved that pyrite facilitates the leaching of chalcopyrite (Berry et al., 1978; Dixon et al., 2008; Mehta and Murr, 1983; Muñoz et al., 2008; Nowak et al., 1984, Tshilombo, 2004). Considering the catalytic effects of pyrite on accelerating the kinetics of chalcopyrite leaching, Dixon and Tshilombo (2005) have developed a new process, known as Galvanox™, which has several advantages over other hydrometallurgical processes. Galvanox™ runs under atmospheric conditions, so it requires only low-cost leaching tanks. The sulfur yield at this temperature is high (>95%) which leads to low oxygen consumption and low sulfuric acid generation. The operating temperature is below the melting point of sulfur which eliminates the use of surfactants. This process also does not require fine grinding. Reaction 1 shows the overall leaching reaction in the Galvanox™ process.CuFeS2 + O2 + 2 H2SO4 = CuSO4 + FeSO4 + 2 S0 + 2 H2O (1)Complete copper recovery from the Galvanox™ process can be achieved at a considerably higher rate than other atmospheric ferric sulfate leaching processes (Dixon et al., 2008). Recycling pyrite and recovering copper from tailings with the Galvanox™ process have also been evaluated in continuous pilot leaching campaigns (Dixon et al., 2007)."

Jan 1, 2012

By R. H. Duthie

As at any other mine in Canada, grade control procedures are used at Steep Rock Iron Mines (1) in order to ensure that concentrator and pellet-plant operator s have a uniform feed so that they can manufacture a pellet to suit buyers' specifications and (2) to maximize ore recovery so that as little as possible finds its way to the waste dump or is downgraded by contamination. At Steep Rock, material grading 40% to 66 % Fe is considered ore. The ore may contain up to 10% sulphur. These ranges create six different stock pile types, with the possibility of more if large concentrations of arsenic are encountered. Although grading and mining techniques used to accomplish these ends are fairly standard, there is an appreciation and willingness by hourly and staff pit personnel to make grade control effective. This produces vertical and horizontal communication, which is necessary for success in this field. At Steep Rock, the waste-to-ore ratio is greater than at any other iron ore mine in Canada. Also, a high percentage of the ore mined is direct pellet feed. For these reasons, .grade control is very important.

Jan 1, 1977

By W. L. Brown

"The properties of Base Metal Mining Corporation are in Yoho Park about 2 1/2 miles northeast of Field; British Columbia; on the main line of the Canadian Pacific railway. There are actually two mines; the Monarch on mount Stephen and the Kicking Horse on mount Field; separated by the steep valley of Kicking Horse river. The outcrops of the orebodies range from 4; 900 feet to 5; 300 feet above sea-level. The concentrator is situated below the Monarch mine and is connected to the main portal by an aerial tramway. The ore from the Kicking Horse mine is conveyed by aerial tramway to a storage bin on the main highway and is then trucked to the concentrator.During the construction of the Canadian Pacific railway through Kicking Horse valley, galena float was found at the base of mount Stephen. The East Monarch outcrop was staked in 1894. The outcrop of the West Monarch ore body on the cliff face of mount Stephen was not discovered until 1916. The Kicking Horse orebodies on mount Field were discovered a few years later. In 1912, a 75-ton concentrator was erected, which operated at intervals until 1924. During this period approximately 42,000 tons were mined and milled, largely from the East Monarch orebody. In 1928, the Base Metal Mining Corporation, Limited, was formed to take over the Monarch and Kicking Horse mines. A 300-ton differential flotation concentrator was erected and production started in the autumn of 1929. In a very short time, however, the low price of metals forced the mill to shut down until August 1933. From 1929 to 1935, when the mill again ceased operation, a total of 256,500 dry tons of ore, averaging 1.59 oz. silver per ton, 9.7 per cent lead, and 12.6 per cent zinc, was mined and milled, largely from the West Monarch orebody. After a period of further underground development, the concentrator reopened in 1940 and is still in operation. From 1940 to the end of 1944, 354,363 tons of ore was milled, averaging 5.32 per cent lead and 10.47 per cent zinc."

Jan 1, 1954

By Gordon MacVean

The object of this paper is to present for your consideration some of the present-day trends of safety practice in the coal mines in the United States and Canada. Coal mining at its best is a hazardous occupation. Men must be experienced miners in order to appreciate the existing hazards and must remain ever conscious of them if they are to work safely. The question is often asked whether our efforts for increased safety are showing results. So often it appears that strides are made for a period of a few years in the reduction of fatalities and lost-time accidents only to have all ground lost by an unfortunate year, after which progress is commenced again only to have a repetition of the same thing. Table No. 1 is an answer to this question. It shows the fatality rates over the last two decades in the coal mines of the United States and Canada. These are given in divisions of five years. The general trend is noticeably downward, exceptions being due to explosions or disasters which claimed an unusually heavy toll of life. These last are certainly not as common today as they have been in the past. It is only reasonable to suppose that this trend towards a lower fatality rate is the result of well directed safety effort. Reliable statistical organizations have offered figures to the effect that only 15 per cent of all accidents can be eliminated by the use of mechanical safeguards. The state of mind of the man involved, or his attitude towards safety, commonly called 'safety-consciousness,' is the controlling factor in the prevention of 85 per cent of our accidents.

Jan 1, 1931

By T. G. Ewart

INTRODUCTION FOR THE purpose of this paper, western bituminous coal is defined as steam coal produced in Alberta and southeastern British Columbia for sale primarily to railways and industries. Before examining present and future markets of this industry, it is proper to review briefly financial and operating conditions within the industry. The report of the Royal Commission on Coal, 1946, supplies financial data from which some conclusions may be drawn. In 1944, the industry as defined above had share capital of $24,886,696. In the fifteen years 1930 to 1944, inclusive, the industry produced: 44,364,211 tons of coal. The profit on this tonnage amounted to $4,678,382.58, which represented 10.6 cents per ton of production. Miscellaneous earnings increased the amount available for dividends to shareholders to a total of $8,487,952.41, which is equal to, 19.1 cents per ton of production. Dividends actually paid in this fifteen-year period amounted to $12,332,040.64, which represented an annual average rate of 3.40 per cent on share capital. It is worthy of note that, in 1944, the net current position of the industry, including investments, was $8,753,874.51. The writer believes that the financial position of the industry with respect to capital, current financial position, and net earnings, has not significantly changed from the fifteen-year period out-lined above. The figures quoted indicate the following situation: (1) The western bituminous coal industry is adequately financed. (2) The industry has followed a conservative dividend policy and has accrued funds for contingencies. (3) The industry has sold its production at very reasonable prices as evidenced by its moderate earnings per ton of production.

Jan 1, 1951

By C. F. Gleeson

"Geochemical stream-sediment reconnaissance can be a useful exploration tool from the point of view of rapidly and cheaply evaluating the mineral potential of an area. This is particularly true of rugged and mountainous areas such as are found in Gaspé. For the past two years, SOQUEM has been carrying out such surveys over favorable geological regions in the Appalachians of northern New Brunswick and Gaspe. To date, about 4,000 square miles of terrain has been systematically covered by reconnaissance geochemistry. Jeeps have been used as a means of transportation in the easily accessible areas and a helicopter equipped with a winch has been used to lower crews into the more difficult-to-reach regions. Such surveys have been successful in finding metallic mineralization which otherwise might not have been detected.Electronic computation of analytical information has been used to construct regional metal maps, rolling mean maps and residual metal maps. These maps have helped in evaluating anomalies, in relating the regional geo-chemistry to the regional geology and in comparing the distribution patterns of metals. To date, some 30,000 stream-sediment samples have been collected from the Gaspe region and analyzed for Cu, Pb, Zn and Mn. These analyses are being subjected to computer analysis."

Jan 1, 1969

By R. A. Hemstock

"Simple classification systems are now being used which will describe adequately the surface vegetation, the topography and the peat for any muskeg condition. Good progress is being made in determining some of the mechanical properties of muskeg and it is apparent that the science of soil mechanics will apply largely to these studies. Correlation is also indicated between shear strength as determined by the shear vane tester and vehicle performance. Several tracked vehicles are now available which perform well in muskeg and advances in this field have come rapidly in the past few years. Testing is under way on the largest of all muskeg vehicles -the thirty-five ton Musk Ox. This vehicle will fill the last gap for the oil industry and will make possible the movement of large drilling rigs at any season of the year."

Jan 1, 1960

By N. R. Paterson

"More than a dozen AEM systems are currently being used in the routine exploration for massive sulphides. The systems differ from one another in minor respects, but fall into four main categories: rigid-coupled in-phase/quadrature systems; towed-bird, single-component systems; differential systems; and passive systems.Although field tests are important in demonstrating the performance characteristics of the AEM/airframe assembly (noise-levels, coupling effects, etc.), more meaningful evaluations can be made through physical or computer modelling. The latter approach has been used to compare the response of twelve AEM systems to both vertical and horizontal sheets, simulating a large orebody and a con-ductive overburden respectively. The effects of height changes are also studied.The results demonstrate that each AEM system has its own particular advantages and disadvantages. The relative importance of these is a matter for the geophysicist to judge, on the basis of specific geological and environ-mental information. Data currently available on AEM systems are adequate to permit an objective evaluation of the systems for a particular exploration program."

Jan 1, 1971

By George Wilkinson

"AbstractThe consistent relationship between the availability of electrical energy and our economic wellbeing is well known. As we develop the energy we need to nurture industrial civilization in decades ahead, we will at the same time reduce our reliance on dwindling supplies of oil and gas. Coal and uranium will be developed as our major fuel sources to meet medium-term. energy needs, followed by fusion and solar energy for the long term.IntroductionTHIS PAPER treats the matter of energy in a way that is quite different from that of the crisis-type atmosphere which surrounds so much of it currently in the news media. On the one hand, we lift the whole subject of energy out from its present-day involvement with short-term issues and take an important longer-term look at the solutions which lie before us. On the other hand, we recognize that short-term issues are important and, as we are reading and hearing, many of the right short-term solutions continue to elude our politicians, our policy makers, and even some of those with knowledge and authority in the energy field.A year ago, if you asked people how they would go about conserving energy, they would probably have said turn out the lights. They would probably say the same thing today, but they might also include other things such as driving the automobile more slowly or putting more insulation in the attic. However, their first impulse is still to use less electricity."

Jan 1, 1977

By R. Glenn Madill

Western Canada is defined, for the purposes of this paper, as that part of the Dominion bounded approximately by the 95th and 141st meridians of longitude and the 49th and 80th parallels of latitude. It is comprised of Manitoba, Saskatchewan, Alberta, British Columbia, Yukon, and that portion of the Northwest Territories lying to the west of the 95th. meridian. The first magnetic observations made in Western Canada were in the interests of navigation by sea. Observations were made by Captain Middleton in Hudson bay at Churchill and York Factory in 1725, and along the Pacific coast by Captain Cook in 1778 and Captain Vancouver in 1792. The first systematic magnetic survey in Western Canada was made between 1819 and 1826 by Sir John Franklin in his widely distributed explorations. It is of interest to find that while the first magnetic declination observations made in Hudson bay and along the Pacific coast were purely in the interests of navigation, the next investigations, which were made in the Western Arctic, included measurements of inclination and force with those of declination. There was a valid reason for this more complete research into the magnetic field as the construction of declination charts depended on the position of the north magnetic pole. Halley promulgated a theory 1683 that " the globe of the Earth may be regarded as one great magnet, having four magnetic poles, two of them near each pole of the equator, and that in those parts of the world which lie near any of those magnetic poles the needle is chiefly governed thereby, the nearest pole being always predominate over the more remote" . The position of a magnetic pole may be defined as a point where the inclination is 90 degrees and the horizontal force zero. It is obvious that the position cannot be' defined by declination observations alone since, for some distance from the magnetic pole, .the horizontal force is too weak to give directive force sufficient to effect the pointing of a compass.

Jan 1, 1948

By J. Béland

"Three stages, each characterized by a particular sedimentation, magmatism, mineralization and deformation, are recognized in the geological history of Gaspe. The first stage led to the formation of the Taconian orogen, the second to that of the Acadian orogen and the third stage to the accumulation of a post-orogenic cover. The Taconian orogen includes volcanic and detrital rocks of Late Precambrian or Cambrian and Lower to Middle Ordovician ages in which ultrabasic intrusions have been emplaced. Folding is severe. Mineralization is of the Cr-Ni-Cu type, related to the igneous facies.The rocks constituting the Acadian orogen include two distinctive sequences corresponding to two successive sub-stages. The second substage began in Early Devonian time with the first pulses of the Acadian orogeny. The rocks of the first substage grade southward from a nearly platformal sequence to an assemblage implying less stability and spotty volcanism. The second substage was one of synorogenic deposition of elastic rocks, first in a marine environment and later under terrestrial conditions. Granitic intrusions, surrounded by aureoles of skarn and hornfels in which Cu-Pb-Zn mineralization is found, accompanied the Acadian deformation. The second-stage"

Jan 1, 1969

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By D. Tetsuka, H. Okamoto

The amount of impurities to be processed in a copper smelting process has increased for recent years because of an increase in the electronic scrap amount. It has been found that Sb and Ni effect on the operation of our copper electrorefining process. It is found that the current efficiency of the copper electrorefining tended to be decreased as the Ni concentration in the electrolyte increased. The passivation of the process seemed to be more related to SO4 concentration in the electrolyte rather than the Ni concentration in it. The current efficiency decreased when the Sb content in the anode was high. A high Sb content in the anode caused easy passivation by forming a gel-like film in the slime layer. We have developed a method to for see the anode passivation in a short time while generating a slime layer. We confirmed the tendency of passivation through the experiment of changing Pb content in anode. Passivation was easily occur with an increase in Pb content in the anode. The amount of slime increased as the Pb content in the anode increased. This suggests that passivation was facilitated because liquid diffusion near the anode was inhibited. INTRODUCTION The amount of impurities to be processed in copper smelting has been growing in recent years because the amount of electronic scrap has increased. Figure 1 shows that the contents of Sb and Ni in copper anodes have increased since 2007.High Sb and Ni contents in the copper anode decreased the current efficiency of the process and made the quality of copper cathode poor because of the anode passivation and the formation of floating slime in the electrolyte during electrorefining. If these influences of impurities are suppressed, it would be possible to make copper electro-refining current density higher and to process much amount of electronic scrap. We examined the components of our copper electro-refining process like anode composition, slime properties and electrolyte composition, and investigated the mechanism by which Sb and Ni affect passivation and current efficiency. When examining the influence of Ni, we noticed that the SO4 important. The effect of SO42 – was also discussed

Jan 1, 2019

By Lloyd F. Dunham

"Crucial to the implementation of new computer-based information systems at Sudbury Operations of Falconbridge Limited was a data communications network that would take computing power to the various mine and plant sites. Falconbridge required a capability to provide on-line data entry, inquiry, and reporting capabilities in three geographical areas, six mines, two mills, a smelter, approximately fifty shops, seven warehouses and numerous administrative offices throughout the Sudbury basin.Conventional cabling methods were rejected based on the projected cost of installation of necessary cables; lack of flexibility to meet the changing requirements of the mine environment; and the risk of losing service to an entire area depending on solitary communication lines.Instead, Falconbridge selected and installed a Data Carrier System (DCS) and Packet Switching Communication System from Teltone Limited, Markham, Ontario. This combined system ""piggy-backs"" computer data over voice-grade twisted pair wire, bringing data to the associated PBX equipment. From there data packets are assembled and routed to the central computer site where they are disassembled for entry into the host machine.Falconbridge has been successful in using existing technology to solve communications problems in a difficult environment. Plans for the future of this network will increase its utilization for technical and real time data communications in addition to the business systems workload it now handles. The Computer Services group in Sudbury is confident that the data highway will handle communications traffic well into the future.IntroductionIn late 1984, the Sudbury Operations of Falconbridge Limited undertook a review of their existing business computer systems. The results of this review indicated that there was an opportunity to improve the timeliness and quality of information coming from the existing computer-based systems while achieving an investment payback by undertaking the project. The greatest benefits from this project would be achieved if the computing tools could be delivered to the employees that were the day-to-day users of the data. Falconbridge's existing business systems were oriented to the batch mode of processing. An alternative solution to using the existing programs had to be found."

Jan 1, 1988

By J. I. Jr. Moore

Many articles have been written about the various operations of Britannia mines and mill, as well as treatises on the geology and ore deposits. A partial list of these papers is given below. Most of these papers have covered well the history of Britannia, and have included a thorough discussion of the geology and ore deposits; therefore, in this paper, no account of these subjects. is necessary. However, a short description of the ore deposits will be given as an aid to a clear understanding of the descriptions of the various mining methods. The Ore Deposits The ore deposits at Britannia occur along a shear zone and are five in number, named for the claims in which they lie, as follows: Jane, Bluff, Fairview, Empress, and Victoria. Each of these deposits is called a mine, as they are separated by 500 to 1,000 feet of barren ground. The Jane mine, although the first producer of the Britannia group, has not been in operation for a number of years. The deposit is a silicified replacement in sediments; with very little evidence of shearing. The Bluff deposit is a highly silicified replacement in porphyry, massive and irregular, very hard in the upper 600 feet with practically no shearing, and softer within chlorite schist in its lower 1,000 feet . The Fairview deposit consists of a series of twelve distinct veins or lodes, rather lenticular in shape, and occasionally merging.

Jan 1, 1928

By William Ferguson, Claude Deveau, Wade Hazel, Stephen R. Young, Allen Lussier, Robert Copeland

"LocationSometimes known as the Bernie Lake mine, the mine is located about 180 km east-northeast of Winnipeg on the northwestern shore of Bernie Lake, close to the Nopiming Provincial Park and the Manitoba-Ontario boundary. The mine is accessed from Lac du Bonnet which is linked to the provincial road system.Brief Description of OperationTantalum Mining Corporation of Canada Ltd. operates an underground mine employing ramp access, room and pillar mining, and shaft hoisting for the production of tantalum, lithium and cesium minerals. Daily campaigned crushing of the tantalum and lithium ores supply separate concentration circuits. Tantalum recovery employs conventional gravity equipment together with recently developed centrifugal concentration methods. All tantalum concentrates go to Cabot Performance Materials for the production of tantalum chemicals and metal. Lithium minerals are recovered using heavy medium separation and silicate flotation to produce spodumene and montebrasite/amblygonite concentrates. The lithium concentrates are shipped worldwide for use in ceramics, specialty glass and mold powders. Cesium processing involves the dry grinding of pollucite as feed stock for the recently built on-site chemical plant dedicated to tl1e production of cesium formate, a high-density drilling fluid for use in the oil industry."

Jan 1, 2000

By E. W. Lucht

THE term "high pressure", as used in industry today, is applied rather loosely. Generally, it refers to pressures that are higher than those encountered in most industrial processes although no definite limits are normally stated. For the purpose of this talk I should like to set rather arbitrary limits to the term "high pressure", and in ab-solute figures this would be the range from 1000 psi to perhaps 40,000 or 50,000 p.s.i. The scope of high pressure technology is very broad, and it would take more time than we have avail-able here today to cover fully even one aspect of the field. Therefore, I should like to discuss just some of the techniques used and problems en-countered in high pressure operations. Research work into the high pressure region dates back about 150 years, but it was not until 1910 that the first commercial application of high pressure technology was made in the production of ammonia.

Jan 1, 1962

By L. Tafaghodi, A. Hosseinpour

"Silicon is considered as the most appropriate semiconductor material for manufacturing solar cells because of its natural abundance and being nontoxic. The transferable knowledge and technology from the electronics industry and the long history of silicon-based semiconductors are also assisting the domination of silicon as the most common semiconductor material. Developing an environmentally and economically viable process for producing solar grade silicon has been one of the main challenges in the silicon industry in the past few years. Metallurgical refining processes have received significant attention because of their high productivity and low cost. Slag refining is one of the purification methods which is based on oxidation of the impurity elements, followed by its dissolution into a slag phase. This article presents a review of various slag refining processes that have been employed for purification of silicon and silicon alloys. SiO2, CaO, CaF2, CaCl2, Al2O3, MgO and Na2O are the major components of the slags used for silicon refining. These slags can be classified into three main categories including binary, ternary and quaternary slags.INTRODUCTION Silicon can be categorized into three different grades based on its application or purity: metallurgical grade silicon (MG-Si) with purity of ~98 %, solar grade silicon (SoG-Si) with purity of ~99.99999 % and semiconductor grade silicon (SeG-Si) which has the purity of 99.9999999 % (Johnston & Barati, 2010; Krystad, Tang, & Tranell, 2012; Tang, Øvrelid, Tranell, & Tangstad, 2009). Producing SeG-Si is carried out through an energy-intensive and complicated process named Siemens. This purification process is relatively slow and involves using toxic and corrosive reagents (e.g. Trichlorosilane). At present the majority of SoG-Si is produced via Siemens or Siemens-like processes and there is very limited production via processes dedicated to SoG-Si. Because of the difference in silicon specifications required in microelectronics and photovoltaic industry, and the cost and energy associated with the Siemens process, an interest has emerged to develop technologies dedicated to producing low cost SoG-Si (Istratov et al., 2003; Johnston, Khajavi, Li, Sokhanvaran, & Barati, 2012; Mitrašinovic, D'Souza, & Utigard, 2012; Wu et al., 2012)."

Jan 1, 2017

By G. T. Lapidus, J. Trejo-Gallardo

A phenomenological model is presented for leaching silver from silver sulfide contained in mineral particles with ammoniacal thiosulfate solutions of copper in stirred reactors. Experimental results were used to adjust the kinetic parameters of the model, such as the reaction order and velocity. The incorporation of the cuprous sulfide-silver sulfide equilibrium at the reaction interface allowed the prediction of the conversion limits for different reagent concentrations. The information obtained from the reactor model was later integrated into a heap leaching simulation, whose results adequately describe tendencies observed in column tests, with respect to variations in copper and thiosulfate concentrations. Comp

Jan 1, 2005

By E. Henderson

"This paper outlines the upgrading of a double-drum 2000 hp cage hoist to provide fully-automatic operation from shaft station control panels. The application utilizes programmable controller technology to provide all necessary functions for movement of personnel and material to 22 locations in a 4000 ft shaft.Various functions involving special design considerations such as ""chairing"", ""jogging"", and three modes of ""multi-level calling service"", are outlined. The use of higher level PLC functions to optimize memory utilization and simulate ""elevator service"" required the addition of a comprehensive fault finding software section to aid in troubleshooting.This paper will deal primarily with the automation portion of the project with references made to other pertinent aspects which were prerequisite to automatic operation. It is not intended to deal with every design detail, but rather to provide an overview of what can be done in the area of automation for those considering such an application. INTRODUCTIONEarly hoisting control systems provided only the essential elements of control, leaving many responsibilities with the operator. With advancements in various areas of technology, electromechanical devices were incorporated to enforce slow-down in end zones, control acceleration rates, monitor safety devices, etc. Brake control systems were supplied to allow for ""single-stick"" operator control, regulated deceleration during emergency brake applications, etc.These additions enhanced the over-all performance but were generally confined to speed and current regulation. Some mechanical devices, such as travelling nut limits, etc.; were used to provide ""position"" control to multiple locations within the shaft. These devices, in conjunction with rather extensive relay control panels, did allow for the establislunent of some automatic cage hoists . The hoists were often limited to service from point ""A"" to point ""B""', involving a limited number of levels due to the complexities of the mechanical interfaces employed. Only limited systematic work sequences were possible . .Programmable Logic Controllers (PLCs) were introduced into industry in the mid-70s and have since gained acceptance in mining applications such as pumping, ventilation, ore handling, etc. This technology, being ""software"" based, allows complexities to reside in the program rather than increasing the number of physical control elements. This has opened the door into hoisting systems for automatic loading and hoisting of ore as well as a means to achieve a comprehensive package of automated cage hoisting functions."

Jan 1, 1989