Search Documents

By T. M. Ruff

A GPS-based traffic awareness and collision avoidance system has been implemented at mines with long, narrow access roads to help avoid accidents involving two approaching vehicles or vehicles following too close. A simple display in the cab of each outfitted vehicle gives an indication of oncoming traffic and a voice announcement indicates the type of vehicle that is coming as far out as 300 meters. Advanced warning of approaching vehicles is increasing driver awareness, especially around blind corners and in adverse weather such as heavy fog, snow, or rain. Speeding alarms have also been implemented and are especially critical as a vehicle approaches reduced speed areas near single-lane bridges or tight curves. A description of the system, safety improvements seen since its introduction, and implementation challenges will be discussed.

Aug 1, 2013

By E. Esmaeilzadeh

There arc 8 primary ball mills in the concentrator plant and their task is material crushing. At the time of balls charge to mills, a lot of noise is produced. This noise would affect all grinding areas. The aim of this research was a reduction about 16 dB at source sound power level (SWL was 129.1 dB). With considering two noise control principles, noise producer sources and propagation paths were specified. For removing and reducing of noise producer sources, rubbers with a thickness of 5-20 mm were used on the all inside surfaces of charge box, ball transferring box and exit canal. For increasing transmission loss and damping coefficient of charge box body, rubber with thickness of 1 cm at outside surface of box was used. For reduction of noise propagation a secondary metal cover was designed and made. This cover includes two parts and was set around the charge box. Glass wool (75 kg/m3) with 10 cm thickness was used as acoustical absorbent between free space of two body's layers and from secondary cover side. The of the rest space was left empty. After installing of secondary cover on the ball charge box no.4, SWL showed a reduction about 16 dB. For studying of control system effect on noise reduction at points far from of charge place, measuring results at these points showed the maximum reduction 12.1 dB and the minimum 11.8 dB.

Jan 1, 2007

By R. A. Nemchek

ABSTRACT Concentrator plant design has evolved from large numbers of small grinding mills to small numbers of large mills. Consequently, plant performance often hinges on the productivity of a single large semi-autogenous grinding mill. Industry attempts to address the grinding mills’ critical nature frequently result in specifications that can be made simpler, more economical, and better focused on the project’s goals. This paper surveys current specification writing practices and proposes an improved approach recognizing that product design, procurement, manufacturing, and quality are interrelated in a successful project. The lessons learned here can apply to all types of machinery specifications.

Jan 1, 2014

By George S. Rice

Foreword Explosion hazards differ widely in the mines of different fields or coal basins. They also differ as between different mines in the same basin or fold, because of variations in gas entering the mines, and because dust conditions and explosion hazards are affected by the mining methods employed and the organization of the work. It is unquestionably true, however, that there are greater differences in explosion hazards in mines of different coal fields or basins than between different mines of the same field or basin. In these respects, the coal fields and individual mines in Alberta are not exceptional. The same conditions obtain in various countries where coal is mined, and are found in single States, as for example in Colorado, where coals are mined ranging in character from sub-bituminous to anthracite, and in attitude from flat horizontal to steeply pitching beds. The U.S. Bureau of Mines, at its experimental mine near Pittsburgh, Pa., has made large-scale tests of the relative explosibility of dusts of coals, ranging in rank from Wyoming sub-bituminous coal containing 19 per cent moisture, to anthracite from Pennsylvania, and including samples from a mine in the Crowsnest Pass district, B.C., and from a Vancouver Island mine. The Bureau has also made similar tests of the dust of coal from a Yorkshire mine which the British Safety-in-Mines Research Board uses as standard.

Jan 1, 1927

By W. R. Cowan

The Caledon Outwash is a large deposit of glaciofluvial gravel and sand located 55 km north west of down town Toronto. For the most part it was laid down in a meltwater channel fronting the Paris Moraine about 14,000 years ago. Applying the braided bar model of Eynon and Walker (1974) the principal facies present are imbricated coarse gravels (bar corefacies); crudely stratified, imbricated bar top sandy gravels; and trough crossbedded side channel sands and gravelly sands. Of lesser importance are crossbedded bar front gravels, shallow braided stream facies gravels, and stoss side facies sands and pebbly sands (rare). Lithologically these deposits are characterized by FIGURE I. Geological relationships of Caledon Outwash. Industrial Minerals in Canada up to 95% Ordovician limestone and siltstone in the gravel fraction. A siltstone content of up to 34% requires that beneficiation be carried out for the production of better quality aggregates. Resources remaining are estimated to exceed 500 million tonnes in 3000 ha of the most suitable part of the deposit. Present production is about 4.5 million tonnes per year, shared by several producers.

Jan 1, 1984

By N. Shi, T. G. Joseph

ABSTRACT: A prototype test dipper (at 1/20th volume and a geometric operating scale of 2.85) was compared during field trials against a conventional dipper with the same tare weight using the same test shovel. Both dippers followed similar dig trajectories, invoked by the shovel operator. A Microsoft® Visual Basic-embedded spreadsheet was used to interpret qualitative visual and quantitative numerical loading data collected on the hoist and crowd dig response. Overall the concept dipper, even with a 50% greater capacity, provided indications of a smoother dig cycle with lower peak hoist loading events and a lower energy per unit excavated.

Jan 1, 2011

By D. J. M. Farnsworth

Since the 1.940's, the bulk of the ore production from the Sullivan Mine has come from pillars. These pillars, located from 100 to 2000 feet below surface, have been subjected to considerable ground pressure. Mining techniques were adopted to minimize the problems of deteriorating ground conditions. These techniques included an orderly sequential blasting of pillars along a retreat front, stage blasting of tall pillars in horizontal slices and utilization of broken pillars as "buffers". The latter two techniques involved leaving substantial tonnages of broken ore in place for as long as 4 years. Rapid oxidation of metal sulphides, with attendant heat and noxious gas generation, had occurred in a few very localized areas of the mine associated with a major water course. However, in a very short period starting in 1972, sulphide fires spread to several of the large blocks of broken ore that had been left inactive for lengthy periods. There proved to be no feasible method of extinguishing these fires, except by complete removal of the burning ore. The attendant problems of handling large tonnages of burning ore have had considerable negative impact on the mine operation. The chemical reactions involved in these sulphide fires have been studied by the mine staff to determine the conditions necessary for' initiation and propagation of the tires. Techniques to safely and efficiently handle hot ore have been implemented and refined. Lastly, and most important, mining methods at the Sullivan Mine have been revised to ensure that additional fires do not occur.

Jan 1, 1977

By G. C. Lipsyy

ALL mineral production? of Can11.da is transported in a mine car at some stage during its extraction. There are as many types and varieties of mine cars as there are of mines. Many of the cars in use were developed in the blacksmith shop. Others were designed by engineers and improved by the mine foremen and the mechanics. Every mine car has the ideas of miner, blacksmith, mechanic, and engineer incorporated in it. Many of these ideas are not generally known. This paper was written to make at least some of this information available to the mining industry. In drawings, tables, and notes, it gives all the important details pertaining to the cars. It .does not recommend any particular type of car for any particular piece of work, nor does it present drawings from which a car can be built. It gives the engineer or master mechanic information on many cars which he can apply to his own particular problems. It is hoped that this information will be of use to mine operators. If a few new ideas are conceived as a result of the paper, the author will feel that the effort of compiling it has been worth while. In order to obtain the data for the preparation of the paper, a questionnaire, copy of which is here reproduced, was sent to all the operating mining companies in Canada. An accompanying letter briefly explained the purpose of the paper and asked for co-operation in furnishing as complete information as possible.

Jan 1, 1945

By S. Devereaux, P. Gover, S. Everett

Having real-time data of blast furnace burden profile with respect to burden height and temperature is critical to making informed decisions on blast furnace operation. Given the high temperature and gaseous environment within the blast furnace shaft, traditional instrumentation has been limited at providing the level of real-time feedback information needed to optimize blast furnace operations. Infrared thermal imagery technology provides non-contact temperature measurement across the entire burden profile, allowing for better understanding of the dynamic movement of the burden within the blast furnace shaft. This technology increases blast furnace performance by improving the decision-making process for hour by hour operations. This paper will discuss the development of incorporating infrared thermal imagery technology into the operating strategy of a lead blast furnace.

Jan 1, 2015

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By D. Paul Bishop, Kevin P. Plucknett, Hung-wei Liu

"Spark plasma sintering (SPS) process has been evaluated for producing the commercially pure (CP) Ti, TiAl and a TiAl-B4C composite. Comparisons were made between the materials in terms of the sintered density, resultant hardness and microstructures. In the present work, the titanium aluminide powders (Ti-48Al, producing a mixture of y-TiAl/a2-Ti3Al) were synthesised „in-house? using a simple reaction-sintering and mechanical attrition approach. This allowed various size distributions to be generated. The powders were then blended with a fine boron carbide (B4C) powder (up to 6 wt.%), and the resulting mixtures were consolidated using spark plasma sintering (SPS) under vacuum in graphite dies. An applied stress of 50 MPa was used for all SPS runs. The SPS parameters were varied in terms of the ultimate sintering temperature (up to 1300°C) and hold time (up to 10 minutes) for each material. It is demonstrated that high densities can be achieved this approach (exceeding 95% of theoretical, with optimised samples close to full density). Microstructural characterisation was conducted using optical microscopy, scanning electron microscopy, and X-ray diffraction. The B4C additions were seen to partially react with the TiAl to form reinforcements, such as TiCx and TiBx. Preliminary mechanical property assessment will also be briefly discussed.INTRODUCTION Titanium- and titanium aluminide-based alloys possess many unique properties, such as excellent corrosion resistance and high temperature strength, respectively (Cardarelli, 2001; Leyens & Peters, 2003). Compared to many other competing materials (e.g. stainless steel or Ni-based alloys), Ti- and TiAl-based alloys also have relatively low densities (~4.5 and ~3.9-4.1 g/cm3, respectively), which is critical for performance in aviation and automobile applications. However, the manufacturing cost is high, due to the expensive raw Ti material and difficulties in machining. TiAl-based alloys are particularly difficult to produce because of their limited ductility (Lütjering & Williams, 2007). To overcome those problems, powder metallurgy (PM) technologies have shown great potential as near-net shape processes for Ti- and TiAl-based alloys. The general PM process largely avoids laborious post-machining and minimises material use. In industrial production, the PM approach has been successfully utilised to manufacture aluminium- and iron-based alloys (Huo & Heath, 2008)."

Jan 1, 2017

By T. J. Wells

THE blast furnace is the base of the steel industry, since there is no commercially practical way of converting iron ore directly into steel. In three hundred years, the blast furnace has developed from a small unit using charcoal as fuel and producing about one ton of iron in twenty-four hours to a furnace making upwards of 1,500 tons a day. The principle of the blast furnace is briefly this: A descending column of stock, consisting of ore, fuel, and flux, is met by an ascending stream of gases, consisting in part of gases formed by the combustion of the fuel and in part of pre-heated air which is blown into the lower part of the furnace. The flux combines with the impurities in the ore and the ash in the fuel to form slag, which is drawn off as liquid.

Jan 1, 1943

"In 2000 the CIM Council approved the CIM Standards on Mineral Resources and Reserves – Definitions and Guidelines, developed by the CIM Standing Committee on Reserve Definitions. The Definition Standards established definitions and guidelines for the reporting of exploration information, mineral resources and mineral reserves in Canada. The Mineral Resource and Mineral Reserve definitions are incorporated, by reference, in National Instrument 43-101, Standards of Disclosure for Mineral Projects, which came into force in Canada in February 2001 and was amended in December 2005.CIM DEFINITION STANDARDS- For Mineral Resources and Mineral ReservesPrepared by the CIM Standing Committee on Reserve DefinitionsAdopted by CIM Council on December 11, 2005FOREWORDCIM Council, on August 20, 2000, approved the ""CIM Standards on Mineral Resources andReserves - Definitions and Guidelines,"" developed by the CIM Standing Committee on ReserveDefinitions. The CIM Definition Standards on Mineral Resources and Reserves (CIM DefinitionStandards) establish definitions and guidelines for the reporting of exploration information,mineral resources and mineral reserves in Canada. The Mineral Resource and Mineral Reservedefinitions were incorporated, by reference, in National Instrument 43-101 - Standards ofDisclosure for Mineral Projects (NI 43-101), which became effective February 1, 2001.At the August 20, 2000 Council meeting a new CIM Standing Committee on ReserveDefinitions was established consisting of the following: John Postle, Bernie Haystead, LarryCochrane, Normand Champigny, Mike Hoffman, Colin McKenny, Jack Mullins, Phil Olson,Fred Payne, Jody Todd and Joe Ringwald.Subsequent to the publishing of the August 20, 2000 CIM Standards on Mineral Resourcesand Reserves, various CIM committees have compiled and published more extensivedocumentation on mining industry standard practices for estimating Mineral Resources andMineral Reserves. These standard practices provide more detailed guidance than that containedin the August 20, 2000 CIM Standards on Mineral Resources and Reserves. On November 14,2004 CIM Council adopted an update to the CIM Definition Standards to reflect the moredetailed guidance available and effect certain editorial changes required to maintain consistencywith current regulations. This version of the CIM Definition Standards includes further editorialchanges required to maintain compatibility with the new version of National Instrument 43-101which is expected to become law at the end of 2005. The CIM Definition Standards can beviewed on the CIM website at www.cim.org."

Jan 1, 2003

By S G. Bergdahl

Underground mining in Sweden is today characterized by mechanization and automation, owing to the rising cost of labour. Drilling in drifts and tunnels is still essentially done with jackleg drills, but rigs wh1ch make it possible for one man to operate two or more drills are now frequently used. Large jumbos for longhole drilling, with two drills operated by one man, are used, especially in sub-level caving. A special drill-rig for drilling through overburden and blasting without removing the overburden has been successfully used in canals and also in ports, where blasting is per-formed under water. The increased use of mining methods based upon long blastholes is a result of the development of equipment for drilling long straight holes. The most common mining method in Sweden is sub-level caving. Extensive research, with model tests, has been carried out in order to determine suit-able dimensions of drifts, sub-levels and drilling patterns. The results have been tried in practice and have given increased yield and less waste rock in hoisted ore.

Jan 1, 1963

By François Girard

La zone 1 de la mine Doyon (zone altérée), se situe à l?extrémité sud de la mine et est constituée d?une série de veines étroites à fort pendage et ayant des épontes de très faible résistance. Les épontes supérieure et inférieure ont des valeurs de RQD variant de 0 à 20 lors que les valeurs de RQD de la zone minéralisée se situent entre 20 et 40. Le minerai de la zone 1 s?étend sur environ 300 m de long et sur 900 m de profondeur avec des épaisseurs variant entre 2 et 15 m. Des méthodes de minage long-trous y sont utilisées avec des accès longitudinaux ou transverses selon l?épaisseur de la zone minéralisée. L?exploitation de la zone 1 a débuté en 1991 et plus de 1,7 millions de tonnes auront été extraites à la fin 2008. Plusieurs techniques y ont été testées que ce soit au niveau du développement ou du minage afin d?améliorer la sécurité des travailleurs, de réduire la dilution des chantiers et d?en augmenter la récupération. Différentes modifications ont été apportées aux dimensions et orientations des galeries, aux patrons de forage, aux techniques de sautages, au support de terrain, à la séquence de minage et aux méthodes de remblayage. Le texte suivant élabore sur plusieurs approches utilisées lors du minage de la zone 1.

Feb 1, 2008

By James A. Finch, Stéphanie Somot

"The self-heating facility developed at the Noranda Technology Centre [Rosenblum and coworkers, 2001; 1995] has now been established in the Department of Mining, Metals and Materials Engineering at McGill University. A research program into mechanisms has been initiated (with support now from four industrial partners under Camiro). The first investigation is into the role of pyrrhotite (Po), the most commonly suspected mineral to trigger self-heating. Following a standard experimental protocol, self-heating was assessed on samples of Po mixed with sand as an inert material. With increasing Po content, self heating progressively increased but, interestingly, the samples visually appeared less and less oxidized. A high Po content, it was hypothesized, may give a more reducing environment favouring formation of H2S. The presence of this gas could be significant as it has a high exothermic heat of reaction with oxygen. The system was modified to test the hypothesis by including copper pieces and copper sulphate to react with (and therefore reveal) the gas as copper sulphide. Evidence is presented in support of H2S production, which to our knowledge has not been shown before and introduces a potentially important avenue of investigation into self-heating mechanisms.INTRODUCTIONSelf-heating of sulphide minerals poses potential environmental and safety hazards in mining of ores, and storage and transport of concentrates. While some conditions are known to be critical, the reactions remain poorly understood making self-heating difficult to predict and control.A major advance in measurement was introduced by Rosenblum and co-workers [Rosenblum et al., 2001; Rosenblum and Spira 1995]. A self-heating assessment method was developed and applied to various sulphide-bearing materials The method is based upon automated calorimetric cells with data acquisition, now available to McGill researchers and which have been used for the study reported here."

Jan 1, 2006

By P. Brad Marchant

"To properly evaluate bioleaching as a commercial alternative for sulphide concentrate oxidation, to enhance cyanidation response, it was necessary to define and optimize critical operating variables outside of the laboratory under less than ideal conditions. A complete bioleach testing laboratory was installed at Equity Silver Mines to aid in pilot plant flowsheet development.A continuous pilot scale bioleach circuit was constructed to provide data for meaningful valuation of biotechnology on a plant scale. The important operating and design parameters for pilot plant testing are described. Plant scale feasibility and design considerations, to treat a refractory pyrite/arsenopyrite concentrate produced from flotation tailing, are discussed. 1.0 BACKGROUNDEquity Silver Mines Limited is located 37 km southeast of Houston in central British Columbia. A 70% owned subsidiary of Placer Development Limited, Equity is Canada's largest open pit silver producer. Ore reserves were estimated at 28 million tonnes grading 106 g Ag/t, 0.96 g Au/t, and 0.38% Cu from two pits, the Southern Tail and the Main Zone. Detailed geology and mineralogy has been described previously(1,2).The concentrator flowsheet consists of conventional crushing, grinding, flotation, and dewatering circuits processing 5 300 tonnes per day of new mill feed. The resultant Cu/Ag/Au concentrate is trucked to Prince Rupert for shipment to market. Mill tailing reports to a closed circuit pond from which mill process water is recycled. Details of the concentrator process have been reported( 2,3).Production in the Southern Tail pit, from July 1980 to March 1984, resulted in mill tailing averaging 0.9 g Au/t and slightly more than 20 g Ag/t. Historic data indicate that unrecovered gold is associated with arsenopyrite and silver losses with unliberated tetrahedrite or minor silve,, bearing sulphosalts. Main Zone mill tailing, which commenced production in March 1984, contains approximately 0.5 g Au/t which is probably associated by majority with silver bearing minerals and pyrite while silver losses, 30-40 g Ag/t, are associated with unliberated silver and antimony bearing minerals."

Jan 1, 1985

By Ernest Baafi

A simulation model RoadSIM using the ARENA modelling system has been developed to evaluate roadway development options for a given development panel configuration. The RoadSIM simulation system has provisions for variability/randomness in operations including cutting and loading at the face, tramming and discharge of coal to the boot end and availability of equipment. The modelling system provides a means for assessing the operational limitations of roadway development practices at a particular coalmine. It is a ?what if? tool that allows a range of equipment, configurations and operating practices to be assessed in terms of achievable advance rates and equipment utilisation. Output from the system is in the form of a dynamic visualisation as well as summary reports and detailed logs of operations over time.

Oct 1, 2009

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By J. O. G. Sanderson

THE Brazeau river is a relatively short foothills stream in western Alberta and its drainage area is limited to approximately 2,400 square miles. It rises near the head of the North Saskatchewan river, about two-thirds of the way from Banff to Jasper, and is confluent with the North Saskatchewan at a point about 40 miles north of Rocky Mountain House. It is not the purpose of this paper to describe the geology of all of this area. Only the central portion, which lies east of the outer limestone ranges and takes in the outer folds of the foothills belt, will be dealt with. This area is shown on Figure 1. A small portion of the area described lies in the drainage basin of Pembina river, which flows into Athabaska river. The area to be discussed may conveniently be termed the 'Brazeau area', since Brazeau is the name of the river basin referred to above, of an out-lying limestone range, and of the only large settlement or community in the region, the mining town Brazeau. One of the first Factors of the fur trading post of Rocky Mountain House in the early years of the nineteenth century was Louis Brazeau. Coal mining during the past 25 years, and more recently exploratory drilling for oil, have brought the district into some prominence. The Brazeau area was visited by D. B. Dowling for the Geological Survey of Canada in 1906 and 1907 (1). His traverses and reports dealt mainly with the Kootenay coal deposits. It is doubtful if he traversed the outer foothills area with which the present paper deals. His reports on rich coal deposits in the Bighorn Basin area attracted commercial interests, and in 1908 large tracts were leased as coal lands. James McEvoy mapped and studied the coal seams in that year, and G. S. Malloch, of the Geological Survey of Canada, made a complete survey of the whole of the Bighorn basin. His report (2), published by the Survey in 1911, describes the stratigraphical geology and names the formations. Further references to the geology of the district, mainly in relation to coal, are made by D. B. Dowling (3) and by J. S. Stewart ( 4). In the period between 1913 and 1920, the area was traversed by private interests in search of likely oil structures. A well was started in 1914 along the Saskatchewan river about 19 miles west of Rocky Mountain House, and drilling was undertaken by Imperial Oil, Limited, in 1921 at Coalspur.

Jan 1, 1939