Search Documents

By H. A. Schnell

"The Phase I Mill at Cluff Lake in northern Saskatchewan was designed to accommodate a very specific high grade uranium ore. As this high grade ore was depleted, construction was undertaken on a new mill circuit (Phase 2) to process a more conventional lower grade ore deposit.The Phase 2 Mill expanded the ore throughput to 800 tonnes per day. The new process employs crushing, grinding, leaching, counter—current decantation, solvent extraction and magnesia yellowcake precipitation and drying to produce a yellowcake concentrate.This paper discusses the process decisions required for this expansion and outlines the new mill circuit. Included is a review of the start up in August, 1984.1.,INTRODUCTION The Cluff Lake Uranium deposit is located 720 kilometers north of Saskatoon in northern Saskatchewan. A high grade deposit was discovered in 1970 with the first production taking place in 1980 after lengthy hearings. The original mill (or Phase 1 Mill) was specifically designed to accommodate this very high grade ore for a very limited plant life.Pilot plant work was carried out in 1981 on the other lower grade ores found in the immediate Cluff Lake area. Feasibility and process selection studies were then undertaken as the Phase 1 mill was nearing its end of life. These studies were completed in March 1983 when approval was given to construct the new Phase 2 mill."

Jan 1, 1985

By C. T. Morley

The steadily increasing interest in high pressure grinding rolls (HPGR) as a legitimate alternative comminution technology for hard rock applications has led to a proportional increase in the demand for trade-off studies comparing HPGR with more established approaches, typically SAG-based but including AG and stage-crushing designs. The primary trade-off is between a) the higher capital cost typically incurred with HPGR-based designs and b) the higher operating costs of the more traditional technologies. However, if, through circuit design innovation, the capital cost penalty of HPGR circuits could be eliminated or reversed, then the need for trade-off studies would diminish.

Jan 1, 2012

By H. L. Martin

A joint federal-provincial approach in gathering basic information from industry on mine production, concentrator operations and ore reserves, initiated during 1978, is a major step toward the goal of achieving better government-industry communication through a common data base. Information from questionnaires sent out by provincial governments is shared with the federal government; correct interpretation is ensured by mine visits conducted jointly by provincial and federal representatives. Initial focus is on nonferrous metal mines. The federal Department of Energy, Mines and Resources (EMR) is responsible for a national analysis that is aimed at the early detection of worrisome developments-and their reasons-in the flow from resources to reserves and from reserves to supply of these metals. The heart of the national analysis is the annual construction of a "monitoring curve", showing each metal's aggregated mine production as it would decrease over time if no new reserves and production capacity were to be added from the year of analysis. For a given metal, a comparison of monitoring curves from year to year can reveal early signs of supply stagnation. In anyone year, a monitoring curve in conjunction with foreseen needs for Canadian mine output will show the production gap that would have to be filled from reserves and production capacity yet to be developed. The production gaps for copper, nickel, zinc and lead, the four leading base metals mined in Canada, are shown for the 20-year period ahead, in the context of production achieved during the past 20 years. It is shown that reserve levels commensurate with likely future production levels would require that average annual reserve additions during 1978-98 exceed the average annual additions during the preceding 20 years. Reserve levels of all four metals have declined in recent years. A review of significant discoveries in the last five years suggests that this fall in reserves is not the result of a lack of exploration successes, but of stagnation in development for various economic reasons.

Jan 1, 1979

By L. Ferland, D. LaRonde, J. C. Caron

"The free-world production of columbium ore concentrates has doubled in the last five years. St. Lawrence Columbium and Metals. Corporation has contributed largely to this expansion, its production rate increasing from 720 tons of concentrates per year in 1961 to 2 200 tons in 1965.To follow the normal market development, the Company initiated an engineering study aimed at establishing the most economical mining methods, thus permitting it to increase its milling rate from 1,000 tpd in 1964 to 2,000 tpd in 1967 and possibly to 3,000 tpd in 1968. The results of this study pointed out the advantages to be gained in converting from an open pit to an under-ground operation. This paper describes how the mining engineering department has successfully developed ""stopes"" from the walls of its No. 2 open pit, in order to assure continuity of its operation during the interval required to develop its underground mine."

Jan 1, 1967

By G. S. Hume

THE discovery of natural gas with naphtha in 1924 in the Upper Palaeozoic limestone of Turner Valley, 35 miles southwest of Calgary, has led to continuous developments in this field. Drilling undertaken soon after this discovery demonstrated that the anticlinal structure was in reality a major drag-fold cut off on the east side by a westerly inclined fault of large displacement. The faulted edge of the .limestone at depth determines the eastern limits of the field, which between 1924 and 1936 was shown to have a gas area 14 miles long by about 1 mile wide. Since the strata dip westerly, away from the axis of the fold, drilling becomes progressively deeper to the west and, with the advent of deeper drilling, crude oil was discovered in 1936 on the west flank of the structure but in the same porous reservoir rocks as the gas on the crest and upper parts of the fold. Since 1936, drilling has been undertaken wholly for the production of crude-oil and at present two producing areas have been found within the Turner Valley structure. The larger of these, at the south end of the field, in the vicinity of Highwood river, has a length of about 4 3/4 miles and a proved width of one mile, whereas the smaller, in the north end of the field, south of the north fork of Sheep river, has only a few producing wells.

Jan 1, 1939

By R. H. Chambers, L. Alderman

"The paper is introduced by an examination of the factors which have led to the present world-wide interest in charging preheated coal to coke ovens. Various possible methods of preheating and charging the coal are considered and reasons are given for the adoption of the methods chosen. The design of the pilot preheating plant for the British Coke Research Association is discussed and its influence on the design of the commercial units for the South African Iron and Steel Corporation's plant at Pretoria and the British Steel Corporation's plant at Beighton are explained. Operating procedures on the pilot plant are described, particularly with regard to the charging of the preheated coal. Design features of the commercial installations, engineered by Simon-Carves Ltd., are explained with emphasis on the built-in safety of the control system of the preheating plant, and the particular problems associated with the erection of such plants on working coke oven batteries. Commissioning and operating procedures are described and the problems associated with the integration of the preheating plant into the normal pushing schedule of the plant are discussed. Preliminary operating results with regard to the effect of preheating on coal throughput on the commercial plants and on the properties of the coke produced are given."

Jan 1, 1972

By Shichang Liu, Hongli Jia, Zhaolian Wang, Maotang Liu, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce and promote a latest technology and equipment for magnetite. It’s featured of purifying concentrate, lowering tailing grade, high concentrate recovery rate and stable operation. HUATE® New Style Elutriation Electromagnetic Separator is an equipment to obviously upgrade magnetite. The slurry is fed into separation area through feeder. Generated by excitation coil, the working magnetic field distributes specially in separation area. Under the combined effect of the background field, excitation and demagnetic field and gravity, the mineral particles float downwards in the form of magnetic chains, and interact with the rising water. The gangue, non-magnetic particles, lean intergrowth,etc will be discarded as tailing via overflow tank and pipe. While the magnetic will be discharged from concentrate pipe. Its grade is 2%-10% higher than that of traditional magnetic separation equipment. It adopts the technologies of transformer oil cooling, alternative and uniform pulsation magnetic field controlling the tailing grade, larger drum feed-in device, more uniform umbrella scattering discharge and stabler output current, and realizes lower coil temperature raise, stabler magnetic field, more uniform discharge, effective isolation of weak-magnetic area from non-magnetic area, more obvious upgradation and recovery rate and lowering tailing mFe%. It’s more suitable to purify and thicken the high grade and ultrafine iron powder. Compared with traditional elutriation equipment, it adopts new technologies in removing impurities, operation, large-scale, process simplification, water-saving, remote control, etc. It optimizes the comprehensive beneficiation index, expands its application scope, reduces resource wastes and increases economic benefits.INTRODUCTIONMagnetite accounts for a comparatively great proportion in various iron resources. As it’s a kind of strong magnetic mineral, we must adopt the weak magnetic separation equipment in magnetic separation process to realize removing Si and lowering impurities. While it cannot do very well to use the common weak magnetic separation equipment in the final cleaning to remove Si and lower impurities. At present, the plants, adopting single magnetic separation process to realize cleaning and removing Si and lowering impurities, are in the minority. Most magnetite plants adopt the flotation separation process to remove Si, lower impurities and purify the concentrate. Though with stable indexes and high Fe recovery rate, the flotation process is very complicated, high-cost and with lots of environmental pollution. If adopting the weak magnetic separation equipment can realize removing Si, lowering impurities and the final cleaning, the magnetic separation process should be the primary choice."

Jan 1, 2016

By Dan Alexander, Ivan Crnkovic, Sarah Schwarz

"Several plant studies have been conducted at the Zinifex Century Mine over the past 5 years. For each of the plant studies, surveys of the zinc primary circuit were conducted, characterisation measurements for each operating cell taken, and the floatability components of the ore mapped to develop a model of the circuit. The floatability components and machine parameters were then used to simulate changes in circuit configuration and operating conditions, enabling further potential improvements in circuit performance to be identified.This paper reviews the current flotation practice at the mine, as well as various circuit changes and developments implemented by site. The application of the methodology and the evolution of the standard procedure are also discussed.INTRODUCTIONBase metals were first discovered in the Lawn Hill region of Queensland’s North West in 1869 and the first mining lease in this area was pegged in 1887 over what is now known as the Silver King vein deposit. The area encompassing these veins, which includes the Century deposit, was proclaimed the Burketown Mining Field in 1899. Exploration titles were granted to CRA in 1987, precisely 100 years after the initial discovery at Silver King, hence the name ‘Century’.Century was commissioned by Pasminco in late 1999, with the mine becoming fully operational on 1 March 2000 and the official opening taking place in April. Pasminco had bought the Century and Dugald River deposits from CRA in 1997 for A$345 million, and invested some A$710 million in bringing Century into production. Today, Century is the world’s second-largest zinc mine in terms of its output, having reached full capacity in 2003.The Zinifex Century Limited (“ZCL”) lead-zinc-silver deposit is located approximately 250 kms north-north west of Mt Isa in north-western Queensland. The deposit is a large flat-lying ore body covering an area of some 1.2 by 1.4 km, the 45 m-thick stratabound sulphide orebody is hosted within an 850 m-thick sequence of Proterozoic siltstone, shales and sandstone, amenable to open-cut mining methods. The mine has ramped up to full production delivering five and a half million tonnes of ore per annum, yielding approximately 900,000 tonnes of zinc concentrate and 90,000 tonnes of lead concentrate. Mine life is expected to be about 8 years"

Jan 1, 2008

By P. V. Avotins, I. Djurkovic, D. R. Nagaraj, M. Grunjic, A. Day

"As part of a major reconstruction and expansion of the Majdanpek Copper Mine, an investigation and optimization of the flotation collector regime was undertaken. The flotation response of the major minerals to various reagents and the effect of pulp chemistry was studied from both a fundamental and practical point of view. These studies led to plant trials and the eventual adoption of a modified collector suite which improved both copper and gold recoveries.INTRODUCTIONThe Majdanpek Copper Mine processes 40,000 tons per day of ore containing about 0.43% cu. In addition to copper, the ore also contains recoverable quantities of molybdenite and gold. The mine has been in operation since 1961 and is the largest in Yugoslavia. It is currently undergoing major reconstruction and expansion. The flowsheet of the Majdanpek concentrator is shown on Figure 1.The ore body is variable in composition and changes in mill feed require proper control of operating variables to achieve the optimum metallurgical results. A detailed study including grindability, flotation response, and solid-liquid separation was carried out on several samples of the ore. Flotation response and the choice of reagent chemistry were found to be very important in achieving the highest recoveries of metal values. An automatic reagent control scheme insured that optimum dosages were used in the plant.The flotation collectors used at the present time include sodium isopropyl xanthate (SIPX), AERO 3302 Promoter and AERO 5415 Promoter. The addition of AERO 5415 to the reagent suite is a recent development and was based on the favorable results obtained in the extensive laboratory testing program conducted to establish the optimum reagent combination and dosages. Subsequent plant tests confirmed that AERO 5415 provided significant improvements in copper and gold recoveries. A description of the mineralogy of the Majdanpek ore and details of laboratory and plant metallurgical data are given in this paper. The chemistry of AERO 5415 Promoter and its interaction with minerals relevant to Majdanpek ore are also discussed."

Jan 1, 1992

By R. D. Brown

In his April 10, 1978 budget address, Finance Minister Chretien declared that the federal government will restrict the growth of its spending to less than the trend growth of the gross national product; over the past year, both the federal and a number of provincial governments have taken action to cut back on spending policies. This new emphasis in restraint would seem 10 be a response to a mounting public reaction to the rapid growth of government spending - and taxation - over the past 25 years. Although this relatively new government posture on public spending may be admired by many, to others it raises the question: "Can the growth in government spending really be stopped?" This article comments on just how government revenues - and spending - have grown over the past few years in Canada, and mentions some of the issues relating to a slowdown in that growth.

Jan 1, 1978

By J. A. Meech, R. J. Tucker

"Since the establishment of froth flotation as an effective method of mineral beneficiation there has been both academic and industrial interest in the levels of the various reagents required to perform the desired separations. Academic interest was spurred by a desire to understand the mechanisms involved - industrial interest by a need to improve the efficiency of the process. These efficiency improvements can take two forms: cost reductions due to reduced reagent consumption and/or improved separation efficiencies. The latter are indicated by either improved grade-recovery relationships for removal of a valuable mineral from gangue, or improved separation of two similar valuable minerals.The processing of lower grade ore bodies at higher tonnage rates has necessitated increased interest in both reagent consumption and metal recovery. Furthermore, the development of accurate and functional on-stream analysis equipment in the 1960's and 1970's has allowed for a better understanding of the dynamic processes involved in a flotation circuit and has required a more concrete statement of the relationships and reactions between the minerals and chemicals in the flotation pulp. Development of these relationships is necessary in order to make use of on-stream analysis to control the process at, or near its more efficient level."

Jan 1, 1984

By O. Matwijenko

"1. IntroductionThe Falconbridge Owl Creek open pit gold mine is located 17 km northeast of Timmins and 2.5 km west of the Kidd Creek metallurgical site. Diamond drilling first commenced in 1964 with open pit production commencing in 1982. Other operations within close proximity are the Canamax-Pamour Bell Creek Mine and the Falconbridge Hoyle Pond Mine.Since 1982, 1,216,000 tonnes assaying 4.5 g/t have been processed in six concentrators. This paper summarizes the metallurgy achieved with special emphasis on some of the unique problems encountered in the processing of this refractory ore.2. GeologyThe Owl Creek deposit, located 3 km north of the Porcupine-Destor fault is in easterly trending carbonaceously altered volcanic and sedimentary rocks. The deposit strikes east and dips steeply north.The ore body can be best described as a wedge shaped sandwich of volcanic basalt between the surrounding sedimentary greywacke. The north and south volcanic-sedimentary interfaces are marked by graphitic zones. The south graphitic contact is more continuous with its thickness varying from 5 m to 20 m as compared to 0.5 m to 3 m to the north. Quartz veins occur throughout the deposit with a predominant vein running along the south contact where it is characterized by numerous graphitic inclusions. Some veins carrying gold values intrude into the sediments in the north. With depth the sedimentary and volcanic zones taper while the quartz-graphitic zones appear to become more dominant."

Jan 1, 1988

By P. Lind, A. Gagnon

"Goldcorp has embarked upon an ambitious, industry-leading, multi-year water use reduction effort. This is a proactive, voluntary effort that reflects our commitment to truly sustainable mining. This effort will focus on increasing water re-use and recycling, and reducing water inputs ultimately towards zero. All of our operating mines are expected to contribute to this effort and are currently in the process of developing plans to meet short and long term objectives. One of the largest needle movers to increase water re-use and recycling is in the area of tailings management. Within five to ten years at Goldcorp, it is envisioned that the need for wet tailings dams will be eliminated and that all new tailings facilities will consist of only filtered or dewatered tailings. Filtered tailings is developing into a mature technology with wide application in mine waste management. This paper describes a conceptual level evaluation on the transition from a slurry to a filtered tailings operation at the Cerro Negro mine in southern Argentina. Key benefits and challenges are highlighted.INTRODUCTION Goldcorp’s Cerro Negro operation is located in the Santa Cruz province in the Patagonian region of Argentina. Cerro Negro has been in operation since 2014 and commercial production was achieved on January 1, 2015. The processing capacity of the plant is 4,000 tonnes of ore per day and in 2016 produced 363,000 ounces of gold and 3.1 million ounces of silver (Goldcorp Inc., 2017). As the mine is located in a semi-arid area, it is important to evaluate technologies that could reduce freshwater consumption and maximize water re-use and recycle rates. The current tailings operation at Cerro Negro incorporates pumping of tailings slurry into a conventionally lined Tailings Storage Facility (TSF). Water is reclaimed from the tailings supernatant pond to the process plant via pumps, however, water losses occur due to evaporation and solution retention within the slurry tailings voids. Converting to a filtered or dewatered tailings operation would allow for increased water recovery prior to tailings disposal, and decreased water losses from evaporation and from retention in the tailings solids void space. This paper describes a conceptual level evaluation on the transition to filtered or dewatered tailings with the primary objective of moving closer Towards Zero Water."

Jan 1, 2017

By F. Hashiuchi

In 1996, the Saganoseki custom smelter & refinery successfully shifted to a single flash smelting furnace operation and increased the copper production capacity to 450,000mtpy in 1998. As the next step, Saganoseki planned to further increase the productivity, especially in the area of P.S. converters and acid plant. As the results of modifications and operational improvements, the gas washing & cooling sections of the Saganoseki acid plant were consolidated from 3 to 2 lines, and increased the gas treatment capacity. The S02 converters in the acid plant were also modified to increase the acid production. By increasing the matte grade from 65 to 68%, six PS converters have been successfully integrated into four, while maintaining the production capacity and reducing the environmental burden in 2005. This paper discusses recent operational conditions and the results of implementation of technological improvements.

Jan 1, 2007

By R. D. Brown

The first step in achieving a rationalization of Canada's crazy patch-work quilt of mining taxes and policies was achieved with the release last November of a major federal-provincial report on the taxation of the Canadian mining industry. The Report, prepared by a group of federal and provincial civil servants, sets out a concise and informative discussion of the major taxation and incentive issues facing the mining industry, and puts forward major recommendations for more rational and moderate taxation policies. It will be considered by federal and provincial Finance and Resource Ministers for possible action by the respective governments. The Report was prepared in response to a directive from the federal and provincial First Ministers in February 1978 to review the federal and provincial taxation of the resource areas. Although the Report is more successful in identifying problems rather than concrete solutions, and reflects some continuing differences of opinion between the governments involved, it does represent an important first step in a comprehensive review of our resource tax policies. This article summarizes the Report, which is some sixty pages in length. Although a detailed discussion of it is beyond the scope of this article, the report itself is recommended reading for those concerned about the current state of the Canadian mining industry.

Jan 1, 1979

By Vicki Tschirhart, Bill Morris, McMaster University

A new method for mapping faults within basement rocks underlying the Thelon Formation and glacial overburden was developed and tested in the Aberdeen Sub-basin. This method utilizes newly acquired aeromagnetic data, the Blakely algorithm for defining magnetic source edges, a calculated dip-direction map, a digital elevation model (DEM) derived from the Canadian Digital Elevation Database, and the positions of identified, inferred and newly mapped faults that are within and adjacent to this sub-basin. Combining these data revealed three age groups of faults. One group is seen only on the DEM; these faults are young brittle structures that have no effect on the sub-Thelon basement unconformity, and are not visible on the dip direction map. A second group is evident on the dip direction map but not the DEM; these faults are old basement structures that did not propagate upward through the Thelon Formation. The third group is expressed on both the DEM and dip direction map; these faults are also old structures that propagated upward during and/or after deposition of the Thelon Formation. The latter group of faults may be of greatest interest for uranium exploration, with reactivation increasing their potential to serve as conduits to transport uranium-rich fluids and focus deposition at or near the unconformity surface. This methodology has promise for comprehensive mapping of basin faults and tracking the tectonic development of the whole Thelon Basin through time.

Jan 1, 2013

By D. P. Bishop, G. J. Kipouros, R. L. Hexemer Jr., I. W. Donaldson, W. F. Caley

Aluminum powder metallurgy (APM) is an advanced metal forming technology frequently employed to fabricate complex structural components in a near-net-shape fashion. Exhibiting nearly 100% material utilization, APM continues to rise in popularity. Recent research initiatives in this field have emphasized the development and processing of advanced 2xxx and 7xxx series alloys. In particular, APM equivalents to wrought 7075 and 2024 have been sought. An overview of work completed in this area is presented. Included are data on the various production stages (powder compaction, sintering, forging, and heat treatment) as well as the microstructure and mechanical properties of the finished products.

Jan 1, 2010

By J. Desroches, J. Burghardt, N. Whitney, B. Lecampion, A. Surdi, M. Houston, S. Stanchits

There is accepted evidence that multistage fracturing of horizontal wells in shale reservoirs results in significant production variation from perforation cluster to perforation cluster. In fact, only a fraction of the perforation clusters seem to contribute to production in many shale gas and shale oil plays. In many cases, the orientation of the lateral section of these wells is determined by lease boundaries rather than principal stress directions, and these often do not coincide. When horizontal wells are misaligned from the far-field principal stress directions, the fracture must reorient from the near-wellbore principal stress directions, which are aligned with the wellbore, to the far-field principal stress directions. The primary objective of this study is to learn how various completion designs influence the near-wellbore fracture geometry when such a misalignment exists. A secondary objective is to understand the influence of rock fabric features, such as mineralized natural fractures, on this reorientation process. To understand these effects, eight laboratory hydraulic fracturing tests were conducted using a true triaxial vessel with 914 mm × 762 mm × 762 mm samples of Niobrara shale. Several different completion designs were studied, including the use of fracture initiation slots with several different orientations and the use of perforations selectively located to encourage a smooth transition from the near- to far-wellbore region. The tests were carefully scaled as accurately as possible to provide insight into the field near-wellbore phenomena. Pressure and fluid flux at the wellbore, deformation of the block, acoustic velocity, and induced acoustic emissions were acquired during the tests. Additionally, sized particles were also injected to gauge the fracture width away from the wellbore. After the test, the blocks were dismantled, and the fracture geometry was mapped in 3D. These measurements allow one to clearly differentiate the fracture initiation and the breakdown—meaning the peak pressure—to be clearly differentiated; the fracture was already well developed when the maximum pressure was reached. The study reveals non-negligible tortuosity and aperture restriction in the near-wellbore region. In the field, this would translate to high treating pressures, uneven proppant distribution, and possibly near-wellbore screenouts. The test results show that, of the configurations tested, the best approach is to use deep slots that are aligned with the far-field principal stress directions. The oriented perforation design did not achieve the simple, smooth transition that was hoped for, and instead produced multiple competing near-wellbore fractures and considerable tortuosity. The study also demonstrated that the presence of planes of weakness, such as mineralized natural fractures, near the slot tip can result in poor near-wellbore fracture geometries, even for the best completion configuration. We conclude from these tests that the misalignment of the well with a principal stress direction creates near-wellbore complexity that, in turn, creates uncertainty in proppant distribution and, therefore, production; proppant might avoid up to a half of the created fracture. Regardless of the wellbore orientation, this uncertainty is further increased by the presence of mineralized features in the rock fabric that can strongly alter or stop the growth of the hydraulic fracture. Preventing those effects by changing the completion alone proves difficult, and new strategies are required to ensure a reliable stimulation of shales.

Jan 1, 2015

By Bird. M.

As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill?s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design.

Jan 1, 2012

By P. J. Noakes

Remote and isolated, located in a frigid, hostile environment, the Black Angel mine in Greenland had to create a warm social environment which would help attract and retain a stable work force of miners and support staff. The high cost of personnel turnover plagues many mines and, when the mine is inside the Arctic Circle, accessible by helicopters which are highly vulnerable to unpredictable weather conditions during the long, dark winters, the potential costs of personnel turnover become critical factors in the success or failure of the mining venture. Manpower planning should start from the date the engineers begin the technical design of the new mine. The plan should include provisions not only to ensure an adequate, skilled work force, but also to ensure a stable work force of people who are happy enough in the mining environment to want to remain, take their vacation and return to work at the mine. The skilled work force was assured with training courses of four months, designed to produce highly specialized underground workers from unskilled Danes and Greenlanders supported by trained Swedish and other Scandinavian miners. The stable social unit was assured by plans the primary attribute of which had to be flexibility. The accommodation changed from shared accommodation with communal washroom facilities to single accommodation with private washroom facilities. A recreational director was hired to help the workers make use of elaborate recreational facilities. A closed-circuit TV and radio system was installed to operate as a private broadcasting system using taped programs originally broadcast on European TV networks or developed by the mine personnel themselves. The liquor rules were changed and the mine manager became a licensed innkeeper responsible for the orderly operation of the Black Angel Bar in accordance with the Danish laws governing the services of a public bar. The result is a relatively stable work force. Some 35% of the people have more than two years' service with the company, Greenex A/S, and some 62% complete 10 months of service.

Jan 1, 1978