Search Documents

By C P. de Jager, J J. Taljaard

Over the past 75 years, the mining of platinum has predominantly focused on the Merensky Reef horizon in the western Bushveld region of the Bushveld Igneous Complex (BIC) of South Africa (Figure 1). The orebody is relatively flat dipping at 10¦ to 25¦, narrow tabular in shape and has been mined to a maximum depth of some 1600 m within Anglo Platinum. This has resulted in the installation of up to four generations of shaft systems as mining progressed into reserves at greater depth. In recent years, with the improvement in processing technology and improved economics, in particular with the improved price of palladium, the mining of the UG2 Chromitite Reef is proving economically viable. The UG2 Chromitite Reef occurs below the Merensky Reef in the succession and the normal separation varies from 15 m to 400 m, with the largest separation between the reefs occurring in the eastern region of the BIC. The UG2 Chromitite Reef horizon is now being accessed from existing Merensky mining infrastructure by cross-cutting back through the stratigraphy where appropriate, or by establishing new decline cluster systems from surface, along the extensive strike length of the various mining properties. These declines are generally established utilising mechanised mining techniques. This paper gives an overview of the techno-economic approaches considered and evaluated for the selection of the optimum mining and shaft systems. More specifically, the paper reviews the design parameters used, techno-economics, conveyor versus haul alternatives, logistics simulations, capital costs, system performance, time to market or ramp-up success, important system differences and lessons learnt.

Jan 1, 2005

The geographical and geological situations of the two mineral sand deposits currently being mined by Western Titanium Limited and the mining methods in use are briefly described. Production scheduling involving the ability to vary the proportions of the major minerals produced, together with maintaining a constant feed grade to the wet concentrator has been assuming greater importance to the company in recent years as the relative value of these minerals, due mainly to technological advances and environmental considerations, is subject to significant and rapid change. Manual calculation, even using a programmable calculator, became a trade-off between man hours and data usage. Schedules were updated infrequently and only a fraction of the avail- able data was used. In July 1975 a Data General NOVA 2/10 minicomputer with a 24K word core and three cassette drives was purchased. A suite of programmes was developed using BASIC to assist in production scheduling and these were opera- tional early in 1976.

Jan 1, 1977

By Sloan GJ, Lysnar RD

Since the of Bergstrand's Geo-dimeter in 1946, and Wadley's Tellurometer in 1956, there have been numerous Electromagnetic Distance Measurement (EDM) instruments produced throughout the world by a variety of companies.This form of measurement has not merely replaced other methods of measurement, but has caused considerable change of emphasis in survey techniques. Major control surveys are now being accomplished using trilateration instead of triangulation. The surveying of open cuts or engineering work may be done in a fraction of the time and, in the majority of cases, to a greater degree of accuracy than with older methods.It is surprising that with this new tech-nology and development of EDM equipment which is compact, easy to use and no longer so expen-sive, no advance has been made in underground surveying. If we look at equipment being used by the majority of mining companies, we see that there have been very few changes since the Second World War. Very little research has been carried out to enable the surveyor to do his work more easily in conditions which, at the very least. are hazardous.

Jan 1, 1984

By Tyson G. R

A novel system has been developed using computer imaging techniques to make on-line measurements of material on a moving conveyor. Meas- urements of the mass or volume of conveyor materials are important in large open pit mining operations such as those operated by the State Elec- tricity Commission of Victoria (SECV). Such on-line measurements can be used for monitoring and controlling the production and transport of coal or overburden, and to assist in maintaining production levels. This paper describes a conveyor burden volume measurement system which is currently under development at the Research and Development Department of the SECV and although targeted initially for use in the Commission's open cut mines, the system is suitable for use on any open conveyor system. A basic developmental system has been built to demon- strate the viability of the technique used and further work on the system is planned. The measurement technique and the major components which have been developed as part of the system are described, some comparisons are drawn with other existing measurement systems and potential errors and future development are discussed.

Jan 1, 1989

This paper summarises the performance of the gold exploration industry in the Western World since 1970, with particular emphasis on the period 1985 - 2003. It identifies the number and size of major (ie >1 million ounce) primary gold discoveries made over this period by location and type of company. Estimates are also made of the likely contribution from smaller discoveries down to 0.1 million ounces. It also assesses the overall trend in the percentage of grassroot discoveries that are converted into mines, and the time taken to get them into production. By comparing the discovery data against total exploration expenditures it is possible to determine the average unit cost of finding a major gold deposit. It is significant to note that the average unit cost per discovery and per ounce of resource has tripled over the last 30 years. An attempt is made to determine the overall economic value generated by the industry. This is based on a detailed analysis of the rates of return and the Net Present Values (NPVs) of 109 major gold projects. After including an adjustment for discoveries not modelled, the NPVs are compared against the total amount of money spent on exploration to determine the value-to-cost ratio for the industry. Based on historical spot gold prices and tax rules, it is found that the return on investment for gold exploration in the Western World over the period 1985 - 2003 was around five per cent real after-tax. The returns achieved in the US and Australia was significantly higher than that for Canada. The returns also appear to have declined in recent years. With regard to the relative performance of junior versus major companies, the paper estimates that the junior sector accounted for 30 - 40 per cent of the total exploration expenditure, and were was associated with 34 per cent of the total number of major deposits, 27 per cent of the contained ounces and 25 per cent of the economic value found.

Jan 1, 2004

By J Vann, S Dunham, M Job

Two-dimensional (2D) estimation approaches have significant advantages over three-dimensional (3D) approaches when dealing with a narrow vein- or layer-like geometry. The main motivation for 2D estimation is that bias due to non-additivity of grade is avoided. The various aspects of 2D estimation are illustrated by use of a case study from the 1A Shoot Nickel deposit at Leinster, Western Australia. The width of the 1A mineralisation is variable, and so are the angles of drilling intersection. Consequently, the variable of interest (in this case nickel grade) is not suitable for direct kriging because it is defined on non-uniform support. However, grade can also be defined as the ratio of two variables that are suitable for direct kriging: thickness and accumulation. In the 2D approach, tonnage equates to thickness and metal equates to the product of grade and thickness, also called æaccumulationÆ. In the simplest approach we can independently krige accumulation and thickness and derive the grade by the ratio of the two resultant estimates. The thickness and accumulation variables must be in a consistent projection orientation, for example a horizontal projection in the case of steeply inclined mineralisation like 1A. Because the density is not constant across the 1A (and most other) deposits, the issue of density weighting is also discussed. The impact of the correlation between grade and length, or grade and density are important issues in implementation of 2D estimation. The circumstances under which these correlations need to be taken into account (by co-kriging) are reviewed. Finally some comments are made on the final use of the resultant 2D estimate for mine planning purposes.

Jan 1, 2003

By B Ilich, M Brad, R Brandli, E MarT

The Wirtgen surface miner was investigated for application to the Cloud Break iron ore deposit since it can selectively mine thin seams and there is no requirement for drilling and blasting or primary crushing as the surface miner cuts and breaks the rock to secondary cone crusher feed size. A physical metallurgical study of the surface miner run-of-mine (ROM) from Cloud Break was conducted to better understand the product size distribution, amount of -31.5 +6.3 mm lump produced, lump stability and physical metallurgical quality compared to conventional drill and blast techniques. Since the Cloud Break mine was not in production, the lump product from crushing and screening of surface miner ROM was compared with product simulations using traditional premining physical metallurgical processing techniques including drop testing of PQ diamond core. Drop test conditioning is widely used in the iron ore industry to simulate blasting, crushing and screening at the mine and subsequent product degradation during handling from mine to port to predict both the amount of lump product on ship and the size distribution of the fines and lump. The size distributions of surface miner ROM for hard, medium and friable ore types show very tight size distributions with very little above 100 - 150 mm, about 60 per cent of the distribution between 75 and 6.3 mm, with less below 1 mm compared to conventional drill and blast ROM. Crushing, screening and drop test conditioning of the surface miner ROM produced more lump in equivalent ore types compared to drill and blast techniques or their breakage simulation using PQ diamond core. The higher lump yield from the surface miner was also confirmed by pilot scale crushing of some 7400 t of surface miner ROM from the Cloud Break trial pit. The lump produced from surface miner ROM was quite stable and showed similar low degradation characteristics to lump simulated from drill and blasting techniques. Product size distribution simulations using conditioned crushed lump from 1 m diameter Bauer hole samples were found to compare well with processed PQ core samples and surface miner product from trial mining at Cloud Break. The Bauer sample method is therefore considered to be a very useful close simulation to actual lump production, although the lump yield is lower.

Jan 1, 2007

By King D, Dickinson S. B, Matheson R. S

Graham Hall and V. M. Cottle (Rosebery, Tas.) : In their paper on "The Mineralized Rift Valleys of Tasmania", Campana, Dickinson, King and Matheson have summarized a wealth of data from many sources. In proposing the new concept of a rift valley structure, they claim to have found a new guide to regional ore control and distribution in North-west Tasmania.Although the authors acknowledge suggestions made by us prior to publication of the pa:per, we are still at variance with their conclusions. We are not convinced that a rift valley structure exist~d when the Ordovician conglomerate was deposited. We are unable to find evidence for Cambrian deposition in a rift valley or reason to project the structure to embrace Hercules, Rosebery, and "possibly" Mt Bischoff.That the Great Lyell Fault (the authors' Owen Rift Fault) is a promising place to look for ore is not a new idea, but the existence of important ore deposits away from the structure reveals its inability to provide an adequate explanation of regional mineral distribution. A well-known structure that does have an influence on ore deposition is not discussed by the authors.STRUCTURAL CONSIDERATIONSThe great thickness of coarse unsorted Ordovician conglomerate lying in an elongate but narrow belt of country is presented as evidence of its deposition centrally within a rift valley, the position-of which is now said to be outlined by resistant slabs of the conglomerate. The marginal shears of the rift are said to show up well along the edges of the conglomerate.

Jan 1, 1959

By M J M Cunningham, M Greentree, J H Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Palaeozoic rocks of north-eastern Laos are an attractive target for gold explorers due to the complex tectonic history and lack of past exploration in the region. Alluvial workings along the Nam Xiang River and its tributaries have highlighted the potential for gold mineralisation in the Vieng Kham region. The Nam Xiang River follows a regionally-extensive NNE-striking thrust fault. Adjacent to the Nam Xiang fault, the dip of the main foliation steepens, and in many places the stratigraphy is overturned as a result of this faulting.United Minerals and Mining Company conducted a regional exploration program to explore for gold. This included stream sediment and rock-chip sampling, and airborne geophysics. Geochemical anomalies were followed up with more detailed exploration, including geological mapping and soil sampling. Despite the relatively deep weathering profile, gold mineralisation is associated with a low-level but well-defined gold-in-soil anomaly. Drilling has shown that gold mineralisation occurs on structures and fabrics parallel to the main Nam Xiang fault. The highest gold grades are associated with brecciated sandstones that have experienced strong carbonate alteration. This suggests that late-stage structures such as the Nam Xiang fault are the major control on gold mineralisation in the region.CITATION:Greentree, M, Cunningham, M J M and Liu, J H, 2015. Gold mineralisation along the Nam Xiang fault, Vieng Kham Project, North-east Laos, in Proceedings PACRIM 2015 Congress, pp 177–182 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Exploration requires substantial capital, and is an extremely risky business (only 1 in 100 prospects ever becomes a mine). The average lead time, that is the time between discovery and production, varies from around two years for a gold mine, to 15 years for a lead/zinc mine. Since it takes years to find, prove and develop most ore bodies, exploration must be carried out years ahead of the depletion of existing deposits. Investors in exploration are exposed to risk for long periods before knowing whether they will receive a return on the funds invested. The risk, high-cost, uncertainty and long lead times involved in exploration make it an aspect of commerce that most managers and investors find difficult to rationalise or understand. Nevertheless, it is a given that the long-term survival of the mining sector depends on discovery of new mineral deposits, however the immediacy of the need to find or acquire new mineral deposits in order to compete and prosper in the industry is less well understood. This paper examines the commercial realities which underlie exploration for new mineral deposits. The first and foremost reason for exploration is to maintain or increase depleting ore reserves which are the asset base of mining, but there are other compelling commercial reasons for exploring, and these are: to maintain return on investment, to achieve growth or create wealth through discoveries which lead tonew mining ventures, to remain competitive in the industry, to diversify, and to control raw material source for mineral processing and/ormarketing ventures. Exploration is necessary for survival of the industry, and also for survival of organisations competing in the industry. The organisations which discover the best orebodies are in the best position to compete, and mining organisations which fail to find or acquire new mineral deposits rapidly become uncompetitive and unable to maintain return on shareholdersÆ investment.

Jan 1, 1998

By L C. Thompson

A new understanding of the formation of black organic shales in the Illinois Basin has contributed to insights on how to produce methane from these complex reservoirs. These shales are far from simple shallow derived sediments but are in fact the result of a complex series of events which include the intermixing of volcanic detritus and the marine organic material, onlap successions and low energy turbiditic intraformational activity. This has led to a review of the commercial significance of the mid Devonian shales in the sedimentary basins of the eastern half of the USA. These shale sequences are also characterised by very little contribution from the underlying Lower Palaeozoic carbonate formations. The later diagenetic influences and the interaction of sea floor bacteria especially since the mid Devonian have lead to the creation of a major source of energy in the form of methane. Vast areas measured in 1000s of square kilometres are known to contain biogenically derived natural gas as methane. However, this vast resource produces very little gas due to abundance of illite which acts as a major adsorption mineral and creates a refractory situation where though there is abundant gas present the rate of release is clearly subeconomic. This paper will present the results of recent laboratory trials which have indicated that it is possible to create microfracturing using bacteria within the gas bearing shale sequence and also restart the methanogenesis process. As most coal bed methane environments have similar organically derived shales in direct relationship to the coal beds themselves then this paper has ramifications for this industry as well.

Jan 1, 2004

By Gao K, Wu C, Langley J. M, Waugh B, Farrell K

The dissolution of carbon from carbonaceous materials into molten iron is a key step in various ironmaking operations. For example, in new direct smelting processes, carbon in the form of coal is injected into the molten iron bath, which leads to the dissolution of carbon. In foundry operations, typical recarburizer materials can range from high purity graphite to chars. The dissolution performance of these" materials is critical to the operation and could dictate the efficiency and economics of the process.Dissolution kinetics has been studied by various investigators to explain the influence of melt conditions and carbon type (Sahajwalla et al, 1994; Shigeno, Tokuda, and Ohtani, 1985; Orsten and Oeters; 1988; Ganguly and Reid, 1992; Wright and Taylor, 1993). The influence of melt sulphur content on the dissolution kinetics has been characterised (Sahajwalla et al, 1994), with sulphur retarding the rate of carbon dissolution. The carbon dissolution from different sources is seen to vary significantly even under similar melt conditions. This observation has been explained by investigators on the basis of the varying ash content present in the carbonaceous materials. However, ash content alone cannot account for the variability in dissolution kinetics reported in other studies. One such study is presented below.In a recent study (Sahajwalla et al, 1994), pulverised carbonaceous materials were injected into the molten iron bath and the" dissolution kinetics was established. The dissolution of graphite and glassy carbon, which contain almost 100 per cent carbon, was seen to be significantly different when the molten iron contained sulphur. The influence of melt sulphur content was explained on the basis of different wetting behaviour observed.Importantly, the study showed that even pure carbon sources dissolved at significantly different rates. Hence, their performance could not be explained on the basis of ash content.The key difference between graphite and glassy carbon is in their atomic structure. Graphite is highly ordered whereas glassy carbon has relatively poor ordering in its atomic structure. This study showed that the atomic structure in carbonaceous materials can have a significant effect on their dissolution performance.The focus of the present investigation which stems from the past study described above (Sahajwalla et al, 1994), is to investigate the influence of atomic structure of carbonaceous materials on their dissolution into Fe-C-S melts.The specific objective of this study is to determine the relationship between dissolution kinetics and crystallographic character of carbon sources. In order to accomplish this goal, a range of different materials representing a spectrum of carbon sources have been chosen for the investigation. These materials include brown coal char, two types of Auscarb (A and B), and commercial graphite. Auscarb is prepared by calcining Auscoal at 1000°C. Auscoal is made from chemically cleaned Australian coals (Bowling, Chandler and Waugh, 1990). Part 1 of this paper details the dissolution performance of the materials studied, while Part 11 describes the X-ray diffraction study. The relationship between the atomic structural dimension and dissolution rate constant is discussed in light of the results obtained.

Jan 1, 1996

By N F. Glenn, S Thiruchittampalam, B P. Banerjee, S Raval

The determination of shear strength parameters for the spoil material plays a crucial role in the assessment of a dump’s stability; nevertheless, their evaluation necessitates laborious laboratory experiments. In order to address this issue, Simmons and McManus (2004) formulated a framework that serves as a foundation for categorising spoils according to their distinctive shear strength parameters based on observable and tactile characteristics. This framework, previously identified as the ‘BHP Mitsubishi Alliance Coal (BMAC) Spoil Shear Strength Framework’, is now recognised as the ‘CoalSpoil’ framework. The spoil characterisation provided by the CoalSpoil framework offers benefits but is not without limitations. The examination of these attributes in the field is a time-consuming task that demands expertise. Subjectivity arises in the spoil characterisation when attributes straddle the line between two categories, such as delineating matrix-supported and framework-supported fabric structures. To enhance consistency in the spoil characterisation process, minimising human intervention is crucial to mitigate bias, classification errors, and safety risks. This study seeks to achieve this aim by introducing image-assisted and automated methods for spoil characterisation.

Sep 1, 2024

By V Narayanaswamy

SustainabilityÆs imperative of economic development in tandem with social advancement and environmental protection is widely accepted, but much debate remains about the practical implications for the minerals processing technologies and practices for the future. Experience in other industry sectors however suggests that sustainability can be a value-adding framework for innovation in processing technologies, business models and management systems. This position paper explores how sustainability can drive innovation in minerals processing, by reviewing pertinent ideas and experiences gained in non-minerals sectors. Sustainable innovations can generally be broadly ranked from incremental to transformative, with each category having its own typical improvement potential, timescale and technological and operational challenges. This leads to a æmud mapÆ for sustainable innovation in minerals processing with three distinct tracks: eco-efficient operations; sustainable plant design and sustainable processing. Competing models for the sustainable innovation process through either forecasting or back-casting, have in common the strong reliance on vision, perspective and competency, which in turn highlights the importance of sustainability frameworks. Such sustainability frameworks provide normative goals and option elicitation prompts to assist with the analysis of current processes and scoping of more sustainable alternatives. A comparative analysis of five prominent environmental sustainability frameworks revealed three cross cutting sustainability themes that challenge current resource processing technologies and practices. These are: fate of materials (zero dissipation of materials); compatibility of materials and processes; and materials intensity of industrial products and processes. Although the sustainability concepts presented in this paper have not been extensively road tested in the minerals processing industry, there is ample evidence that recent initiatives in the Australian resource sector illustrate the applicability of the proposed framework. It is therefore argued that more in-depth assessment of sustainable innovation concepts would be a valuable contribution to the sustainable resource processing theory and practice.

Jan 1, 2004

A substitute for rutile can be produced by leaching natural or pre-treated ilmenite in hydrochloric acid. Ilmenite in its natural form is an extraordinarily inactive mineral from which the selective removal of iron is rather difficult. The reactivity of ilmenite so that it can be leached with dilute hydro- chloric acid (=2O% w/w) can be enhanced by pre-treatment steps of oxidation and re- duction. The temperatures at which oxidation and reduction are carried out have an effect on both the kinetics of these steps and the leaching kinetics and optimum temperatures for oxidation and reduction are 950 and 850¦C respectively. The mechanism of leaching of iron from pretreated ilmenite and the effects of rate of agitation, temperature, acid con- centration and addition of ferrous chloride to hydrochloric acid on leaching kinetics and production of fines are discussed in the paper.

Jan 1, 1984

By Y Peng, D J. Bradshaw, X Chen

At NewcrestÆs Telfer gold mine, a strategy of regrinding pyrite rougher flotation concentrates has been proposed to increase gold recovery and reduce cyanide consumption in the CIL circuit. The regrinding will be followed by an additional copper/gold flotation stage, where copper minerals need to be separated from pyrite. However, although the minerals are well liberated, the separation of chalcopyrite from pyrite in the cleaner stage is not always straightforward. The surfaces of the fine particles, produced during regrinding, are more easily oxidised and contaminated than coarse particles, directly influencing the particle floatability. The depression of pyrite is difficult in the cleaner stage as well due to copper activation, a process which is also highly dependent on the grinding environment. In this study, different grinding media, including mild steel and stainless steel, was used in the regrinding to produce different regrinding chemistry, such as, pH, Eh, and iron hydroxide contamination. The effects of regrinding conditions on chalcopyrite flotation and its separation from pyrite were studied. It was found that the stainless steel grinding media, which produced an oxidising environment, was more beneficial for the separation of chalcopyrite from pyrite after regrinding. The mild steel grinding media had a detrimental effect on both chalcopyrite and pyrite flotation. This study addresses the importance of choosing suitable regrinding conditions in the pyrite and copper flotation circuit.CITATION:Chen, X, Peng, Y and Bradshaw, D J, 2012. Effect of regrinding conditions on the flotation of chalcopyrite and its separation from pyrite in the cleaner stage, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 279-286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M J. Nugus, S C. Dominy

Mesothermal lode-gold deposits often pose problems during sampling because of their complex and erratic gold grade distribution, and the presence of coarse gold. Effective sampling and sample preparation protocols must form the basis of any resource estimate at whatever stage a project is at. Design of a sampling regime must be based upon a thorough understanding of orebody mineralogy and geology. This should include consideration of gold particle size and distribution. The sample type, size and density employed must also be based on the underlying geology of the deposit. Choice of sample preparation procedure and assay type is of critical importance if fundamental sampling error and analytical errors are to be minimised. Traditional fire assays, using small charge sizes, consistently understate assays gained from large charge sizes and techniques such as screen fire assay and bulk leach extractable gold assay. The proportion of coarse gold within samples will have a profound effect on the requirements for sample preparation and assay method. The application of Gy sampling theory can help to reduce errors within the processing of samples of broken rock. Quality control/assurance of sampling regimes must also be critically assessed. The problems associated with sampling mesothermal lode-gold type deposits are presented as case studies from Western Australia and North America.

Jan 1, 2003

By Sneddon J

This Is not a highly technical paper, but rather an attempt to give a general outline of coal mining for the benefit of those present who may have little or no experience in the industry, and is intended to give some general knowledge which may help to a better understanding of the problems of the industry. A knowledge of the disposition of workable material is necessary to give a comparison with other mining practices. Coal Is usually found in comparatively fiat seams of varying thickness, whereas other minerals are generally found in highly inclined lodes of variable width. However, even in comparatively flat seams unaffected by faulting, grades can, and do, vary greatly over short distances.This variation causes many local problems in working the small area affected. Even very steep seams, and some are much steeper than 1 in 1, vary considerably not only in grade, but also in direction of grade and level course. This is probably caused by folding during alteration of the shape and form of the basins after deposition.These swellies are common to most coal seams and vary only in extent. This type of variation in grade and direction of grade, while common to most ore bodies, is a matter of great importance in coal mining when it is considered that roadways are driven in the seam itself and have to be graded and made suitable for haulage purposes.The area of ground involved in an individual coal mining operation is often very large; many times larger than most metal mining propositions, and often comprises many thousands of acres.When it is considered that the specific gravity of coal may be only one-fifth of that of some ores mined, and the coal seam may be five or six feet in thickness, the vastness of the area necessary for continuous mining operations over many years will be realised.To achieve comparable outputs, with about five times the bulk of material to handle, much more ground and working places must...

Jan 1, 1947

By Graham J

The successful processing of arsenopyritic ores is difficult and will be facilitated by a better understanding of the mineralogy of gold within arsenopyrite and the type of arsenopyrite in which gold is taken up. Solid solution gold in arsenopyrite is now well documented, and is a significant cause of refractory behaviour in gold processing. Investigations of the crystal structure and stoichiometry of arsenopyrite by X-ray diffraction, electron microprobe analysis and convergent beam electron microscopy have been carried out in order to understand how the gold is incorporated into the structure. Variations in stoichiometry, particularly the As:S ratio, of arsenopyrite leads to variations in structural parameters. These variations result in slight changes in thermal behaviour. The distribution of invisible gold in an arsenopyrite grain is generally non-uniform and synthesised samples contain up to 2 wt per cent gold. A transmission electron microscopy (TEM) technique called ALCHEMI is being used to identify the substitution site. The process of gold agglomeration together with evidence of an ordered breakdown of arsenopyrite to pyrrhotite has been documented with the use of TEM. An arsenopyrite grain containing invisible gold was heated with an electron beam resulting in recrystallisation of arsenopyrite to pyrrhotite with arsenic being expelled. The gold is mostly insoluble in the pyrrhotite lattice and therefore exsolves out and combines with other gold atoms to form droplets at the boundary of the pyrrhotite.

Jan 1, 1992

By Farley RJ

The use of D-H Vacuum treatment at the Waratah Works of Commonwealth Steel Coy Ltd is broadly discussed in relation to the wide variety of products manufactured by the Company. The metallurgical features of the process are considered and related to the quality benefits deriving from its use.

Jan 1, 1972