Search Documents

By M Binks

This paper presents a case study that describes the selection, development, engineering and construction of a process plant for the biological oxidative pre-treatment of a refractory pyrite-arsenopyrite gold ore flotation concentrate. Prefeasibility and feasibility study resource modeling, metallurgical testwork, and environmental and engineering studies are outlined. Options considered for oxidation of the ore, which examine cost, risk, operability, recovery, engineering and environmental aspects are compared, with particular reference to pressure and biological oxidation. The BIOX« biological oxidation process was selected as the preferred oxidation process and the flow sheet for this process is presented. Selection of the BOIX« process resulted in special requirements for the feed preparation circuit, residue treatment and disposal, materials of construction and engineering. Use of a biological process in ore treatment also introduces particular process and engineering risks the management of which are discussed.

Jan 1, 2004

Routine, in-pit geological mapping of highwall at Central Queensland Coal Associates (C.O.C.A.) deep strip mines has proved too slow for the increasingly greater highwall lengths which require mapping. This realiz- ation has encouraged the search for faster mapping methods and after trial of ground photographic methods has resulted in the adoption of interpretive mapping off stereo cover, oblique -- aerial photography. This entails using a Cessna 182 light aircraft flying at its slowest speed, the aerial meth- od finally employed consisting of two Vinten, air reconnaissance cameras mounted in parallel and simultaneously taking both colour and black and white photographs of the mine high- wall. The respective 1:500 scale enlargements produced from the 70mm format films combine to present the sharpest resolution attainable under the field conditions pertaining and such information on weathered material as only colour photography can fully render. Total costs for the aerial photography method are estimated to be about the same as those for conventional in-pit mapping. Whilst total costs are comparable, geo- logist's time for mapping a 10 km. length is reduced to less than half that for in-pit mapping (for Stage 1, fully accurate mapping) and accuracy and detail are greatly improved. A permanent, accurate record of overburden

Jan 1, 1981

Optimisation and sensitivity analysis of final pit limits is now an accepted procedure for open pit planning studies. Tools to assist the design engineer in an underground metalliferous mine to make optimal choices for the selection of major development, stope geometry and cut-off grade analysis have not been available. The engineer has had to rely on experience and a limited analysis of design alternatives. A new tool called the `floating stope' has been developed to define the optimal (boundary) limit for material that can be economically extracted by underground stoping methods. The method is analogous to the `floating cone' method of open pit optimisation. The geology and mineralisation are modelled as a regular or subcell block model. Included in the model are structural and geotechnical features, and any previously mined out areas. Inputs to the procedure include the minimum stope dimensions, cut-off grade, stope head grade, and the way in which dilution is to be calculated. The optimisation procedure can be directed to maximise ore tonnes, grade, contained metal or the economic (dollar) value of material mined. The procedure can be applied at each stage of mine evaluation and design to assist with preliminary resource appraisal, selection of stoping methods, and detailed mine design. As with open pit optimisation procedures, manual intervention by an experienced engineer is required to produce practical and detailed designs. This practical design should follow the optimised design as closely as possible. The paper outlines the algorithms used in the definition of the stope envelope, and describes the analysis and results of several case studies where the optimisation procedure has been applied.

Jan 1, 1995

By Haeussler P, Christie A, Bradley D, Skinner D

Mesothermal gold deposits of southern Alaska and Westland, New Zealand have both formed at the seaward edge of major collisional zones in the Pacific basin. In Alaska, production of large fluid volumes correlates in time with the addition of heat into the lower parts of the accreted terranes in the late stages of collisional orogeny. This heat was critical for driving both the metamorphic reactions that released the large volumes of fluid that carried the gold, and the contemporaneous widespread anatexis and magmatism. In Alaska's Chugach terrane, this heat was produced by subduction of a spreading ridge beneath the North America continental margin in the Eocene. The resulting products were the S-type granites and gold-bearing veins. The similar widespread S-type plutonism and gold veining in Westland's Buller terrane suggest that a similar tectonic event could have triggered ore formation along the southeastern edge of Gondwanaland. Based on the Alaskan model, a Devonian or Early Carboniferous age is favoured for high volume metamorphogenic fluid generation and gold vein formation in Westland.

Jan 1, 1995

Currently there is considerable interest in the production of DRI in Western Australia to take advantage of intense interest from the Asian market. Most DRI is produced using gas-based processes and is used as a feedstock in electric arc steel furnaces, otherwise known as mini-mills. This paper critically examines the technical and economic issues of various gas-based DR processes available today and recommends the most effective and attractive processes suitable for Western Australian iron ores.

Jan 1, 1996

The factors affecting performance of base and precious metal smelting and converting processes are considered in relation to reactor characteristics. The chemical differences between processes are related to these factors for different reactor systems. The complete smelting and converting flowsheet involves a number of operations. The process selected for a particular feed and product requirement should be one which optimises the efficiency of the process, the cost of building and operating the technology and the long-term maintenance and productivity of the units.Ausmelt's approach to achieving an efficient process using its technology is described in relation to the smelting of copper concentrates for production-of blister copper.

Jan 1, 1992

By Medhurst TP, Trueman R

The aim of the paper was to model numerically some aspects of the extraction of coal pillars by split and fendering. A two-dimensional elasto-plastic plane strain model with strain softening and interface mod- elling was used. The model was able to simulate the improvement of conditions experienced in lifting from the fender, when the roof adjacent to the fender has caved. In contrast, when a stook was left, providing support to a span of uncaved roof, the model pre- dicted the fender would suffer considerably more de- formation and strain.

Jan 1, 1992

By Amelunxen R, Finch JA

Flotation columns represent an important addition to flotation practice. Columns have largely replaced. conventional machines in molybdenum cleaning in Canada. Columns have been successfully tested on bulk copper/molybdenum cleaning at Gibraltar Mines Ltd. A rougher cleaner/scavenger cleanercombination was shown to be capable of giving higher grades and recoveries compared with three stages of conventional cleaning. A control strategy for the columns has been developed. An interaction between gas hgldup and wash water rate has been exploited to control performance.

Jan 1, 1985

A numerical model of the spontaneous combustion of coal has been developed and is being used to investigate the nature of self-heating in underground coal mines. Results to date confirm the complexity of the self-heating reaction in coal and illustrate the impact of the factors such as the coal reactivity, mass and airflow through the coal pile. Subtle differences in the chemical, physical and environmental conditions and make a significant difference in the development of a high temperature self-heating or a low temperature benign condition, the subtlety escaping normal underground observations. Additional work is planned to investigate the thresholds for such factors in the development of spontaneous combustion and it the implications for detection by gaseous Products.

Jan 1, 1998

Production scale experiment study was carried out in a limestone open-pit for testing the theory and method proposed by the author(Zou, 1987). The results of experiments indicate that the mathematical model and computer programs, which include the consideration of both the three dimentional distributions of the weak planes and the energy densities of explosion stress waves, reflect the physical process of rock bench blasting quite well. The predicted fragment distributions coincide well with the practical fragment distributions measured with the photo-image analysis method proposed by the author(Zou,1989). The paper "A Three Dimensional Mathematical Model for Calculating the Rock Fragmentation by Bench Blasting in the Open-pit"(Zou,1987), which was published in some conferences and journals, has interested some scholors and researchers. In order to test and improve the model, a group of production scale experiments were carried out in a limestone open-pit during 1986-1987. The procedure and results of the experiments are illustrated in this paper.

Jan 1, 1990

By J Stojanovic, V Kasic

Gold-bearing polymetallic sulfide deposits are common in Serbia, and mostly occur in the Karpato-Balkan and, to a lesser extent, the Serbo-Macedonian metallogenic province. These deposits û Coka Marin (Majdanpek), Grabova Reka (Blagojev Kamen), Lece (Medvedja) and Veliki Cip (Boranja) û are dominated by Cu and/or Pb-Zn mineralisation that contains a variety of Pb, Zn, Cu and Fe (¦ Sb, As, Bi) sulfides and sulfosalts, as well as native elements. Gangue minerals are composed of quartz, carbonates and rare silicates and barite. Based on their gold content these deposits can be divided in three groups:1. Polymetallic deposits with a high gold content (>1 g/t).2. Polymetallic deposits with an intermediate gold content (0.1 to 1 g/t), and3. Polymetallic deposits with a low gold content (<0.1 g/t). Gold occurs as native gold or as an alloy with silver. Native gold ranges in size from 5 to 20 ¦m, with a few rare grains over 100 ¦m, as isolated grains or as microveins (in the first group of deposits). Its distribution within the deposit in uneven. Native gold in the second group is smaller in size (1 - 5 ¦m, rarely 20 ¦m), where it is uniformly distributed in a quartz-silicate matrix. The third group is of no economical importance. The subject of research has been the first group of polymetallic deposits.

Jan 1, 2008

Rajasthan of western India blessed with rich base metal and phosphorite deposits. The biogeochemical and geobotanical methods of mineral exploration are greatly used in parts of Rajasthan Zawar, Khetri and Ambaj multi-metal project Gujarat and Jhamarkotra phosphorite deposit. These principles are exclusively based on certain assumptions about the anomalous chemical composition in plants and distribution and migration of indicator elements. Biogeochemical studies for lead zinc deposit of Zawar group of mines were carried out to locate the probable accumulators which could help in prospecting for these metals. The important roots of Impatiens balsamia plants contain 735 mg. of cadmium and crotolaria linifolia 603 mg., melhania futteyporensis 626 mg. lindenbergia muraria 443, celosiu argentia 360 mg. In the Khetri copper belt the vegetation is scanty and the species includes Acacia arabica, zyzypus jujuba and cactus euphorbia.

Jan 1, 1988

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998

By Felice J. J

The assessment of the face velocity of blasts is important in the analysis and subsequent improvement of blast performance. POWERWAVE RADAR is a new tool which will make the collection of this data easier for blast researchers. The data collection technique ensures that a large amount of face velocity data is collected from a blast, and describes the velocity characteristics of the face at a new level of detail. This results in a greater understanding of the effect of drilling and blasting parameters on blast performance. Several case studies are presented which illustrate the collection technique, the type of data generated and how the data is used.

Jan 1, 1992

AXTAT is a computerised system developed by the Western Australian Department of Minerals and Energy in conjunction with the local mining industry for recording and retrieving information about fatalities and work related injuries. Since its inception, the system has gained considerable recognition by consistently demonstrating its usefulness as a tool, not only to the Department, but for the entire industry nationwide. AXTAT has played an important role in the continuous improvement process in management of occupational health and safety in the Western Australian mining industry with gains in both human and financial terms, by regularly providing timely and accurate statistical feedback on fatalities and lost time injuries to industry.

Jan 1, 1996

By B B. Beamish, M S. Kizil

The processes that take place during the development of a heating are difficult to visualise. Bulk coal self-heating tests at The University of Queensland (UQ) using a two-metre column are providing graphic evidence of the stages that occur during a heating. Data obtained from these tests, both temperature and corresponding off-gas evolution can be transformed into what is effectively a video-replay of the heating event. This is achieved by loading both sets of data into a newly developed animation package called Hotspot. The resulting animation is ideal for spontaneous combustion training purposes as the viewer can readily identify the different hot spot stages and corresponding off-gas signatures. Colour coding of the coal temperature, as the hot spot forms, highlights its location in the coal pile and shows its ability to migrate upwind. An added benefit of the package is that once a mine has been tested in the UQ two-metre column, there is a permanent record of that particular coals performance for mine personnel to view.

Jan 1, 2005

Facies associations in the Okiduse Volcanics, woodlark island, suggest that two major volcanic centres erupted synchronously during the Middle Miocene. These centres are referred to as the Watou Mountain Eruptive Centre and the Uvarakoi Caldera. The Watou Mountain Eruptive Centre, centred on Boganuse Mountain in the Okiduse Range, was a typical, moderate-sized composite volcano (or stratovolcano). The seq-uence is readily divisible into lava (Boganuse lava unit), breccia (Nikuben breccia unit) and epiclastic (Talpas sandstone unit) dominant facies, typical of composite volcanoes. These facies girdle Boganuse Mountain and they are interpreted to represent vent, cone forming and ring plain associat-ions, respectively. These facies indicate a reconstructed volcano of approximately 1,700m height with a basal diameter of 7km. The presence of limited exposures of intrusive associated with the vent facies (Kuike'beimmicrodiorite) suggests that the volcano is only partially dissected. The Uvarakoi Caldera is a felsic volcanic system contrasting with the mafic Watou Mountain centre.

Jan 1, 1994

By A Logan, B Cuthbert

Brown and Chitombo (2007) indicated that during the last two decades, the international mining industry has been using mainly mass mining methods to extract safely and economically some of the important commodities such as copper, diamonds, gold, iron and nickel. Mass mining may be implemented either on the surface through large open pits or underground using mining methods such as sublevel, block and panel caving. Developments in the last ten years have demonstrated that caving methods can be applied successfully in strong orebodies at greater depths and in increasingly challenging geotechnical environments for which more traditional mining methods would be unsuitable, unsafe and/or uneconomic. These underground mass mining challenges require æfront endÆ investigation and analysis, robust engineering design and disciplined implementation and operation. Newcrest Mining Limited has focused its efforts on the development of gold/copper projects of substantial scale and margin. To help achieve this, the company is applying and further developing mass mining methods. These include large-scale open pits (OP) and underground mining methods such as sublevel (SLC), block (BC) and panel caving (PC). Block and panel caving now offer economies of scale opportunities for Newcrest to achieve high production rates at lower production costs; thus enabling the exploitation of mineral endowments at higher margins. This paper discusses the practical aspects of caving technologies that Newcrest continues to develop through its expertise at Telfer and Ridgeway SLC operations, Ridgeway Deeps BC and Cadia East PC projects.

Jan 1, 2008

By Le V, Nguyen Ngoc Quynh, R H. Murfitt

The Truong Son Fold belt in Indochina hosts the significant Sepon gold-copper district (Laos) and the similar gold-basemetal districts of Phuoc Son and Bong Mieu (Vietnam). With over seven years of exploration, Toronto-listed Olympus Pacific Minerals Inc, is one of few foreign companies that have to date made a substantial investment in mineral exploration in Vietnam.Much of this work has been conducted along the Phuoc Son û Tam Ky Suture, on the south-eastern limb of the Truong Son Fold belt on the Vietnamese side of the border with Laos. These programs have produced a significant number of gold prospects at varying stages of exploration development. The Phuoc Son û Tam Ky Suture is a major Paleozoic subduction zone that extends from northern Laos, through Central Vietnam and out into the South China Sea.It represents a Lower Mesozoic collision zone between the Paleozoic-age Truong Son fold-belt terrain to the north, with the crystalline terrain of the Pre-Cambrian Kontum Block to the south. Since its formation, it has been a locus of deep faulting, continental accretion, intensive intrusive activity and mineralisation. This paper briefly discusses the geological setting, structure, metamorphism, mineralisation, exploration history, and proposed mining development of the Olympus Phuoc Son Gold Project, with particular reference to the Phuoc Son û Tam Ky suture.

Jan 1, 2004

By Davey FJ

The Hikurangi Margin of eastern North Island New Zealand represents the feather edge of the over-riding Indo-Australian Plate at its convergent boundary with the subducting Pacific Plate. Towards the south, convergence becomes slower and increasingly oblique, and sediment supply from the Southern Alps becomes increasingly rapid. In this environment a 150 km wide, imbricate thrust, accretionary prism has grown since the Miocene, uplifting slope ridges and basins and a range of coastal hills. Offscraping of thick, axially transported, trench-fill turbidites begins in a zone of proto- thrusts, which extends up to 25 km beyond the principle, slope-toe, deformation front. On the slope, landward tilted, trench-slope basins are separated by ridges. The ridges ride up on thrusts that sole out at a major decollement. The decollement dips landwards at 3 degrees to a depth of 14 km at the coast, where it coincides with an onshore zone of high seismicity. Beneath the decollement, about 1 km of consolidated, oceanic sediment is going under the margin with the underlying oceanic basement. Some of these sediments may underplate the frontal ranges to the west and geochemical evidence of subducted sediment is found in the volcanic zone beyond. A rapid decrease in the width of the accretionary prism to the north is associated with a decrease in sediment supply and perhaps with a dislocation in the downgoing plate. To the south, the accretionary prism narrows, swings westward, and merges into the zone of very oblique collision that marks the transform between mirror image subduction to north and south of New Zealand.

Jan 1, 1987