Search Documents

One of primary causes of poor blast performance is the improper relief of explosive energy. Under or over-confined blasts modify the explosiveÆs path of least resistance, which changes where and when the explosive energy is applied resulting in less than optimum blast performance. During the research for this paper the overbreak characteristics of five full-scale blasts were quantified using high speed cinematography and borehole cameras. The effectiveness of various overbreak control methods was also evaluated to guide design refinement. The results of this research along with general recommendations for reducing excessive damage are included with this paper.

Jan 1, 1999

The difference between a hypothetical and a theoretical approach is considered and the advantages in using a hypothesis is discussed. Virgin horizontal stresses play an important role in stabilising strata which bridge across an excavation, and reduces the tensile stresses which develop in a beam subjected to bending. Simple formulae are deduced for the bridging of a thick massive stratum under such conditions. At shallow depths, tensile failure on the upper side of the beam is the most likely cause of fracture, but below a certain depth this gives place to compressive failure on the underside, with the possible incidence of rock bumps. The presence of strong massive beds delay the onset of subsidence and may restrict the width of the subsidence trough. If the material involved in the caving is strong, this will reduce the final subsidence, especially at shallow depths. The British regulations for the control of aquifers and their dependence on the strain developed at the seabed are discussed. As an alternative, the concept of a disturbance factor is introduced to permit the consider- ation of aquifers at depth, leading to an explanation of the make of water on the first faces to be mined in the Selby Coalfield. 'Elie paper closes with a brief consideration of the different roles played by longwall face supports in the control of readily cavable strata, and the control of strong beds which hold up in the waste.

Jan 1, 1986

By A B. Richards

Time window analysis that limits the explosive mass fired within a specified time window (commonly eight milliseconds) has been used for many years in blast design by explosives engineers. Despite several warnings in the past that this technique has limited practical or scientific basis and, in many cases, does not effectively control vibration, almost every textbook and blasting manual refers to time window charge mass limits as a primary vibration control technique. It has become entrenched in some blast vibration management plans, despite being inappropriate for the particular situation. With the flexible initiation timing available with electronic detonation almost a practical reality, and the 8 ms constraints in-built into the signal tube initiation system thereby lifted, it is timely to review the significance of the 8 ms time window in controlling blast vibration. This paper re-visits the original research that led to the development of the 8 ms criteria and the non-supportive conclusion of the original researcher. Because airblast was not measured, the 8 ms time window was never intended to be applicable for airblast control. Examples of blast designs are given in this paper that comply with the 8 ms time window limit that result in substantially increased air and ground vibration, together with examples of blast design that does not satisfy time window considerations, which results in reduced air and ground vibration. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid high blast vibration situations that result from the inappropriate application of time window techniques and other adverse delay combinations.

Jan 1, 2003

Since the mid-1970s there has been increasing attention in the South Pacific area to the problems of disaster planning and management at various levels, mainly from regional through national to provincial levels. This concern has been expressed in a variety of ways. International aid donors have made their views known in commentaries or reports. Seminar discussions have been organised at the regional level (such as at Suva, 1976; Suva, 1979; Tonga, 1982 and Suva, 1983). In-country training workshops or meetings have been organised (such as the "Disaster Preparedness Workshops for Non-governmental Organisations" in Pacific countries, jointly run by the Australian Red Cross and the Australian Overseas Disaster Response Organisation and supported by AIDAB, in Vanuatu, 1985; Solomon Islands, 1985; Western Samoa, 1986; Fiji, 1987; Tonga, 1987; Lae and Port Moresby, Papua New Guinea, 1988) or held outside the area (ACDC at Macedon, 1981). Training and/or research institutions have been established such as the East-West Center, Honolulu, and the Asian Disaster Preparedness Center, Bangkok (more Asia oriented). As part of the East-West Center Pacific Islands Development Program's Disaster Preparedness Project, a detailed manual of disaster preparedness and response procedures and guidelines has been published (Carter, 1984).Table 1 and figure 1 show that the area with which this discussion deals is a highly fragmented island region, comprising many small, some minute, nations, both in land area and population. The social structure is predominantly rural, with the capital city often making up a small part of the total population and, in absolute terms, little more than a small town. Outside the administrative and governmental activities concentrated in the capitals, in most cases the indigenous inhabitants depend on subsistence agriculture or on usually a monocultural concentration on a cash crop, most frequently coconuts.

Jan 1, 1990

Perhaps no aspect of the investigation of an ore-deposit is of greater importance to the mining geologist and engineer than a consideration of its geological structure. A thorough understanding of the type, size, shape, and arrangement of any ore-body is essential to the proper conduct of exploratory, developmental, and mining, operations. Significant as these remarks are' in relationship to ore-deposits in general, they become of paramount moment when a complex structure such as the Broken Hill Lode is in question. In this connection the use of the term "lode" as applied to the Broken Hill ore-bodies may terid to confusion of ideas among those not familiar with the field or with the literature pertaining thereto, by reason of the fact that it is generally understood that a "lode" is characterised by simple, tabular form, regular outline, defined walls, and persistent attitude. However, as the terminology is well established by common usage, itsretention appears desirable, and, for the purpose of this paper, the name "The Broken Hill Lode" refers to that complex unit which includes pre-eminently the famous ore-bodies exposed in the workings from the North Mine on the one extreme to the South Blocks (Zinc Corporation) Mine on the other.That the practical value of geological investigation, of the ore-bodies was realised by the Geological Sub-Committee of the late Scientific Society of Broken Hill is attested by the...

Jan 1, 1932

The paper reviews the majority of associations and institutions which operate in support of the Australian mineral industry. The review covers historical aspects of each organisation and the current activities and management structure. The linkages between the organisations through membership are briefly discussed. The paper comments on the evolution of the formation of the organi- sations and the networks between them that do exist and operate regu- larly. Rationalisation or a process to consider formation of new groups to fill gaps in the network are recommended for further research.

Jan 1, 1988

By R Hindstr÷m

The demand for iron ore has increased dramatically in the last years and is forecast to remain on a stable high production level for years to come. ItÆs expected that the world economy is facing a stable continuous growth of iron ore to two billion tonnes and more over the next decades (Beddows, 2007). Furthermore it is expected that the existing and known high-grade ore resources will decline, and the iron ore industry will be forced to implement more and more advanced beneficiation plants. As a consequence of the more complex beneficiation requirements, there will be a need for modern solutions for iron ore dewatering that are reliable mechanically as well as cost effective and with high capacity per unit at the same time. Conventional vacuum filtration methods have been the most prevalent in fine iron ore dewatering. Product quality needs, lower ore grades, complex mineralogy and energy costs have resulted in iron ore producers seeking better solutions for dewatering, in particular pelletising feed. New advanced filtration methods have been introduced to the market. This paper describes how these modern methods are answering the needs of the industry. Performance of advanced dewatering technologies (pressure filtration and ceramic capillary action filtration) for iron ore applications has been studied, and the findings are based on both industrial and pilot scale experiences on different materials. For example, the results show that the cake moisture content of iron ore pelletising feed can be optimised more effectively by using modern filtration technologies. By selecting the most suitable and adjustable equipment, the effects of variations of feed material on downstream processes can be minimised and the possibilities of processing more difficult raw materials to high-quality pellets are better. The Larox Corporation develops, designs and manufactures industrial filters and is a leading technology company in its field. Larox is a full service solution provider in filtration for separating solids from liquids. As such, this paper compares the new developments in this market area with the prevailing known vacuum filtration technology, but focuses on a comparison between capillary action filters and rotary vacuum disc filters (RVDF). The trade name CeramecG is used to differentiate the Larox filter from the generic term.

Jan 1, 2007

The Sto Tomas II orebody of Philex Mining Corporation is a porphyry copper deposit located at Padcal, Tuba, Benguet, Philippines. It was mined through open pit method for the first two years starting 1958 and subsequently through underground method using the Block Cave System. The slusher type of draw was employed at the upper levels of the orebody from mid-year of 1959 up to 1994 and then shifted to LHD as the ore became more competent at the lower levels. Application of rock mechanics played a vital role during the conceptualisation of the LHD method of draw, the first of its kind in the Philippines. Rock mechanics is a combined responsibility of the geology and the mine engineering staffs, with the geology providing the vital information to the mine engineering to include in the mine planning the following:the general geology of the orebody; the ground characterisation through rockmass classification; determination of the cavability of the ore column (this includes our experience on airblasts which occurred during the early stage of our last slusher blocks); undercutting sequence; fragmentation of the rockmass in the ore column; drawzone spacing; proper draw control procedure; lay-out of openings; and the design of ground supports based on the rockmass condition. For the proper interpretation of the rockmass that would cater to the diverse mining situations, Philex adopted the modified geomechanics rockmass classification (Mining Rockmass Rating, MRMR) as this system is recognised and used by most of the block cave mine worldwide. This paper aims to discuss and present the role of rock mechanics in the analysis and determination of geomechanical issues encountered in Philex mechanised block cave operation.

Jan 1, 2000

An extensive railway construction prog- ram in the People's Republic of China has required the excavation of many tunnels in difficult ground, particularly in mountainous regions. Conclusions drawn from case histories permit guidelines to be formulated as to the optimum location of tunnel alignments in faulted and folded terrains, and also in karst regions. Geological factors adversely affecting durability of tunnel linings can be minimised by adoption of appropriate construc- tion practices.

Jan 1, 1987

The current boom conditions in the Gold Mining Industry, open cut low grade gold mines have become the initial cash flow source for most companies. To achieve the required cash flow the head grade needs to be maintained at the required level. The methods of grade control to achieve .the planned head grade have evolved various systems, one of which is the Ditch Witch Trencher. The application of this machine has revolutionised open cut grade control and Geology and this paper records the various methodologies developed in the Eastern Goldfields of Western Australia.

Jan 1, 1987

By A W. Bewsher, T C. McCu, D B. Mapleson

The Miitel nickel sulfide deposit has been overprinted by a family of late stage structures that have acted as conduits for fluids that have contaminated the orebody with arsenic minerals. This has resulted in highly variable and unpredictable arsenic grades throughout the Miitel orebody. The ore produced from Miitel is processed under a toll-treatment agreement with Western Mining Resources Kambalda Nickel Concentrator. Part of this arrangement includes a financial penalty if monthly average arsenic grades in ore delivered exceed 800 ppm. This constraint has provided an extra challenge to the Miitel mine geologist in addition to daily underground duties. Routine development and stope mapping, close spaced sampling and cross-sectional interpretation were used in building an understanding of the structural controls of arsenic mineralisation and ore repetition at the Miitel nickel mine, and in providing maximum input to mine planning and scheduling. The distribution of structures responsible for arsenic introduction is now well understood from detailed mapping, sampling, and interpretation. By applying these insights to mine scheduling, the operation has successfully managed arsenic levels within the required specifications. Geological mapping has also improved the understanding of the structural complexity of the ore deposit, leading to the addition of ore tonnes and an increased confidence in resource modelling. Regular sampling and tight controls on data quality provided confidence in a strongly skewed arsenic data set. Multiple Indicator Kriging has been used for resource estimation of the arsenic contaminated nickel ore since it allows explicit control of the spatial influence of extreme grades in the positively skewed arsenic sample population. Both the grade control and exploration data sets are used to model the arsenic distribution.

Jan 1, 2003

The value derived by good mine planning is often underestimated as many mines steer their attention to the more immediate and more easily recognised successes made by the day-to-day operational æbush fireÆ fighting. Similar to machine maintenance, the efforts made to quickly rectify short-term breakdowns are well recognised; whereas the value derived from the work in planning, scheduling and undertaking preventative maintenance is not so obvious or readily quantified. Too often the focus of the business shifts to building and supporting an efficient operations team at the expense of developing a highly experienced team of mine planning practitioners that are well trained with procedures and purpose-built tools to develop optimum mining strategies. A resource has an inherent value based on its quality parameters and its likely mining conditions. How well that value can be unlocked is governed, to a large degree, by the proficiency of the mine planning practitioners, as they, essentially, set the foundation of the mine business and the path along which the mine will operate. The importance of having a well documented and procedural mine planning methodology that integrates both a thorough technical and economic understanding of the resource cannot be over emphasised. The aim of the mine planning process is to develop a robust mine design and production capability which can best cater for future uncertainty whilst providing the best opportunity to maximise cash flow into the business. The planning process must be transparent and auditable, clearly summarising the process steps and assumptions made to arrive at a justifiable and defendable outcome. To provide maximum value to the business, the planning process must be repeatable and scalable to enable easy replication throughout the different mines and projects within an organisation. The diminishing numbers of highly experienced personnel within our industry, coupled with the growing pressure to clearly demonstrate that appropriate due diligence has been exercised, means that well documented and monitored mine planning processes using purposed built and innovative tools need to be developed to ensure optimum outcomes.

Jan 1, 2009

The Transportable Moisture Limits, as ,measured by the procedures laid down in The IMCO Code of Safe Practices for Bulk Cargoes, determine the target moisture contents for the concentrates produced at the West Coast Mines of Electrolytic Zinc Company of Australasia Limited at Rosebery. Filtration of these concentrates gives moisture contents considered to be low in comparison with those achieved for similar sulphide concentrates, but which are very close to these Transportable Moisture Limits. The filtering techniques used are outlined and the problems associated with-maintaining concentrate moistures below the required limits, together with the methods used to solve these problems are discussed.

Jan 1, 1978

The maintenance system for underground mobile equipment at Cobar Mines Pty. Ltd. has been modified from that originally planned as a result of experience gained in operating the equipment.Downtime due to breakdowns has been reduced by improvement of vehicle servicing and overhaul procedures.Frequency of breakdowns can be reduced by training operating and maintenance personnel to a high standard, ensuring adequate numbers of tradesmen and supervisors, good maintenance facilities and communications, a well designed mine layout, and a comprehensive stock of spare parts.A maintenance and downtime summary is compiled for each four-week operating period and this is useful in highlighting particular problems where corrective action must be taken.

Jan 1, 1969

During October 1947 an Authority to Prospect was granted by the Minister of Mines to lVIount Isa Mines Limited over an area of approximately 75 sq. miles to the north of Mount Isa.Application for the Authority to Prospect had been made after Zinc Corporation Limited had been granted prospecting rights over two areas, one of 1,265 acres immediately to the north of the Mount Isa Mines leases and the other of 1,960 acres adjoining the south end of Mount Isa Mines leases.METHODSAs a means of providing a cheap map of sufficient accuracy on which to plot geological features, both Mount Isa Mines Limited and Zinc Corporation Limited agreed upon aerial photographs and the two companies shared the cost of an aerial photographic survey by Adastra Airways of 130 sq. miles which covered the prospecting areas held by both companies.The photographs were on a scale of 800 ft. to I in. with 60% overlap on the north-south runs and 25% overlap east-west. A set of alternate prints enlarged to 400 ft. to 1 \in. were obtained for field work. The 400 ft. to 1 in. scale unglossed photographs (size 18 in. x 18 in.) were taken On to the field and rock outcrops, and uncorrelated structures were plotted directly on to them in red crayon pencil. The geological observations were then transferred in the office to a tracing on which accuracy of azimuth and scale was controlled by use of a photo mosaic and ground surveys.

Jan 1, 1953

The Ida Valley in Central Otago is one of series of parallel basins filled with freshwater sediments. The basins are in fact tectonic depressions superimposed on NE trending grabenlike structures which occur in the area and are the result of block faulting possibly initiated in Cretaceous times and concluded in late Tertiary and early Quaternary. In Central Otago this tectonic event affected metamorphosed rocks belonging to the eastern facies of the New Zealand Geosyncline and collectively known as the Haast Schist Group. These rocks constitute the basement and the shoulders of the tectonic depressions. The Ida Valley occupies the depression wedged in between the Raggedy Range to the NW and the North Rough Ridge in the SE. The valley is approximately 38 km long, 3 to 7.5 km wide and is drained by the NE flowing Pool Burn, which meets the SW flowing Ida Burn. The resulting unified stream flows into the Manuherikia river which drains the next door depression to the NW. The present work deals with the Ida Valley basin and more specifically with the geology studied within two Prospecting Licence areas held by Gold Mines of NZ Ltd on the southeastern flank of the valley.

Jan 1, 1977

An image analysis system has been built which automatically digitizes camera input of rock fragments, analyses the digitised data to determine the sizes and shapes of the rock fragments, and outputs the analysed data to a printer in the form of a histogram or a scatter chart. The high speed of such a system allows for direct collection of data from material thrown into the air by blasting, material travelling on a conveyor belt, and material free-falling on to a stock-pile or into or out of a rock-crusher. Data on the blasted, un-crushed material provides information on changes in the lithology and structure of the rock face as it is quarried or mined: flatter fragments may represent approach to a brittle, unstable shear zone, or a change from sandstone to shale; so that the informa- tion reflects the effect on the sizes and shapes of the fragments by the blasting process and/or by the rock structure. The size and shape distributions of rock fragments produced during blasting and during processing may now be continuously monitored. Such detailed analysis of the results of fragmentation is labour-intensive and expensive when the size and shape distributions are obtained manually, but is cheap and efficient when using this image analysis system. Such a system will enable the results of blasting, quarrying, mining and crushing to be cheaply analysed and correlated with current and changing indus- trial practice so leading the way to increased productivity.

Jan 1, 1988

Analysis of different environmental scenarios and to represent, spatially, of impacted areas is possible by the use of geoprocessing techniques, specifically Systems of Geographical Information (SIG). Through these systems it is possible to create dynamic mathematical models, constituting of a georeferenced digital database and employing the integrated data originated from several sources. In this context, the general goal of this paper is to apply this tool in an environmental analysis of a specific karstic area impacted by mining activities. In order to preserve a limestone site, internationally recognised by its archaeological features, including caverns, lakes and evidences of prehistoric ages, the Brazilian government has created the Lagoa Santa Environment Protection Area. This place is located in the proximity of the Belo Horizonte international airport. In the past two decades exploitations of dimension stones have increased in this area. These exploitations have been done without a mine plan promoting several environmental impacts. The objective of this paper is to analyse these activities using SIG as a basic tool to locate the main mining related impacts and propose mitigation measures including waste and tailings disposal and reshaping of the landscape and introducing a drainage system for the considered zone.

Dec 6, 2010

By Shklyar FP, Babushkin NM, Bokovikov BA, Fedotov PB

A mathematical model for gas flow dynamics and heat and mass transfer processes occuring in the tuyere raceways and in the zone of the final for- mation and heating of pig iron and slag has been developed and simulated on a digital computer. It takes into account the formation and size of the raceway zones, combustion of coke and its substit- utes, oxidation of the metal, radiation from the gases to the raceway boundaries, physical heat losses and the direct reduction of the pig iron elements below the raceway zones. To evaluate the distribution of heat produced by the oxidation of metal between gases and prod- ucts of smelting, the problem of heating the mat- erials in the raceways with the sources of heat in the materials under conditions of intensive gas circulation in the raceways is solved. To determine the amount of heat transferred by radiation from the gas to the boundaries of the raceways, the problem of radiant heat transfer be- tween two grey bodies forming a closed system is solved. Using the structural parameters of the furn- ace, the inlet parameters of the combination blast and exit parameters of the melt, the model permits the calculation of the temperatures of materials entering and leaving the raceways and also the res- idual temperature of the gases, which qualitatively differs from the theoretical combustion temperature. Analysis of the operation of several different blast furnaces has shown that the overall picture of the interaction between gas flow dynamics, mass and heat transfer processes occuring in the race- ways and in the zone of final product formation, obtained with the aid of the model, now permits us to approach from a different position the deter- mination of the limiting factors in furnace operat- ion. It also allows us to explain certain phenom- ena observed in blast furnace practice and to dis- cover new relationships which may be used in analy- sis and control of the smelting process.

Jan 1, 1981

By E V. Man, O N. Savassi, J-P Franzidis

In flotation, the property that is exploited to effect the separation of a mineral from an ore is referred to as its floatability. Assessment and quantification of ore floatability is of fundamental importance in modelling and simulation of flotation circuits. This paper describes the design, construction and operation of a new laboratory flotation rig that has been developed at the Julius Kruttschnitt Mineral Research Centre (JKMRC) to determine the floatability of different ores on a small-sale. The rig is designed for continuous operation. The major features of the rig are highlighted in this paper. An unique characteristic of the rig is a 9.1 L conditioning vessel. This provides a mixing regime close to plug-flow which avoids complications such as different collector coverages for similarly sized particles (which would considerably increase the complexity of ore floatability determination). The main advantages of this rig when compared to conventional batch flotation cells include better control of the chemical environment and the ability to determine froth recovery, entrainment and water recovery with increased accuracy. Preliminary tests undertaken with a high-grade lead/zinc ore from BHP Cannington are presented demonstrating the good level of reproducibility obtainable in operating the equipment.

Jan 1, 2000