Search Documents

IT is most remarkable and valuable property of mediurn and high carbon steels that they should be so susceptible to heat treatment, the wide range of variability in tenacity, ductility, etc, due to the normal influence of the carbon in the untreated material being enormously inereased thereby.The physical properties of steel and other metals are much more closely related to their structure than to their ultimate analysis.For instance, we may by chemical analysis determine the carbon content of a steel to be 0.5% ; but this information alone is insufficient to enable us to say what are the physical properties of the metal.Such a steel may possess 11 tensile strength of anything from 35 tons per sq. in., with much ductility, up to 80 tons per sq. in., with practically no ductility, according to its heat treatment. A microscopie examination, on the other hand, would show the structural composition of the steel, from which its physical properties could be approximately deduced. From this it will readily be understood that the microscope has played an important part in the development of modern rnetallurgy, and to-day it is in daily use for the examination of metals and alloys in the laboratories of most works dealing with the rnanufaeture and working of metals.THE IRON-IRON CARBIDE EQUILIBRIUMTo understand fully the mode of occurrcnce of the different constituents of a knowledge of the Iron-Iron Carbide equilibrium diagram (Fig. I) is essential to heat-treat steel successfully and to interpret microstructures correctly such a knowledge isabsolutely indispensable.A portion of the Iron-Iron Carbide Diagram, dealing with steels below 1000 and containing up to 1 carbon is given below.It should be noted that the diagram deals entirely with pure carbon steels, and does not indicate the influence of the usual so-ealled "impurities" present in all commereial carbon steels...

Jan 1, 1926

AND INTRODUCTION The Lochiel coal deposit, a large Tertiary soft brown coal deposit in the mid north of South Australia, is currently being investigated by the Electricity Trust of South Australia (ETSA) as a potential source of fuel for a base load power station. Feasibility studies indicated that the proposed dragline method of overburden removal was viable but economically sensitive to both highwail and dump batter angles. The unusual properties of the unconsolidated overburden sediments and the groundwater regime posed a number of intimately related hydrogeological and geotechnical questions which were addressed before and during the excavation of a trial pit. All strata at Lochiel are of soil strength, and artesian aquifers occur above and below the coal. From the initial evaluation of the deposit a number of hydrogeological questions were defined. These related to the rate at which the pore pressure in the silts is reduced by dewatering, the extent of the reduction in pore pressure due to prestripping, and the feasibility of dewatering and depressurising carbonaceous silty sand sequences. The site of the trial pit was selected to answer these and other questions from the basis of a detailed geological, hydrogeological and geotechnical understanding. The trial pit dewatering system simulated a full scale mine dewatering system and included ten pumped wells, twenty drainage wells, and nearly 400 monitoring instruments. It operated from September 1986 to June 1987. The excavation was carried out between February and May 1987.

Jan 1, 1988

Mining is a high risk, high capital and potentially high reward undertaking. A large proportion of the risk comes from a lack of definition of the orebody (which also provides some of the potential) and the unpredictable nature of the market. This makes the planning process difficult but encourages the development of a robust yet flexible mining system. The system should be capable of absorbing some deviation from the anticipated concept without a significant impact on profitability. The mine planning process tends to consist of a series of related but discrete stages. For instance, the pit shells are designed, a schedule for the pit shells is created, a plant fleet is chosen to achieve the schedule and a financial analysis is carried out on that scenario. It is likely a few iterations are carried out using various mill throughputs to produce a favoured financial result. The problem is that handing results from stage æBÆ for use in æCÆ doesnÆt encourage a flexible system. æCÆ is likely to be built for exactly æBÆ. Unfortunately, in mining, æAÆ (the orebody) has the highest potential for variability and impacts everything else downstream. æDÆ the market also has high potential for unplanned variability. These variations can spread and æreverberateÆ through the whole mine process. For example an unexpected increase in ore oversize impacts all downstream mine processes to the primary crusher which may in turn create problems back æupstreamÆ by restricting throughput rate. Also an unexpected drop in demand or price could require modifications to the planned production rates. This paper looks at how mining process simulation can be used to support the development of strategies to counteract unforseen circumstances or alter production to match fluctuations in demand and price.

Jan 1, 2003

This opportunity to present a few thoughts on the question of professional education and training comes at a most appropriate time. In Britain, a great deal of energy is being expended in this, so-called, post-Finniston era, to create a new look for the status of engineers and engineering by the Engineering Council. Naturally, the tune and the tempo are being called by the big institutions which essentially serve the manufacturing industries. However, the Engineering Council in Great Britain also includes the mining and processing institutions such as the Institution of Mining and Metallurgy (IMM) and so there is a chance - if it is taken - for us to contribute to the debate and the determinations that emanate from it. The IMM, of course, caters for the professional status of those engaged in the mining and minerals industries and includes many who do not see themselves as engineers. Nevertheless, the debate is important to these other groups whose livelihood is inextricably bound up with those who are engineers and there are many facets of the engineering policies being shaped that will, I am sure, eventually be enshrined in the requirements for professional status across all the various disciplines in our industry.

Jan 1, 1986

There is a well-known saying, variously attributed to the great King Solomon and other sages of antiquity, to the effect that 'there is nothing new under the sun'. The inventive genius of man, as far as it is personified in the metallurgist, has often had the truth of this statement poignantly brought to mind when investigating the priority of ideas in its own particular branch of science. Not infrequently some operation, at first inilocently taken for a novel procedure, has later been found to have had an irrefutable precedent in the more or less remote past.When confronted by a question of this kind the metallurgist can generally much simplify his search if he at once turns his scrutinising gaze towards that ancient home of metallurgy, Germany. Vast departments of the smelting art have originated there, and even when Germany has not been in position to claim priority of invention, it has at least been characterised by a distinction equally as worthy - ie that of the faithful and authoritative exposition of the theoretical grounds on which the invention rests.In the present instance, in endeavouring to trace the history of pyritic smelting, the writer has naturally turned in the abovementioned direction, and not without some result, although the recorded data are, as might have been expected, meagre. A complete history of the art of beneflciating ores by means of fire, in all its many ramifications, still remains to be written. Possibly it may never be written, for the extent of the subject is tremendous. It is even practically impossible to clearly trace the development of one of its most modest sub-branches in satisfactory detail, or to present that branch without going to a considerable extent into related matters of a merely general character. For the purpose of dealing with the subject it will be convenient to divide it into two concurrent heads, and to distinguish, for historical reasons as well as for metallurgical ones, between that branch of the general method of matte smelting, which, until about 1891, has been called 'pyritic smelting', and the more recent offshoot of the latter, which, by distinction, may be called 'pyrite smelting'. The nature of pyritic smelting was clearly defmed by Dr John Percy in 1880, and his interpretation3 may be accepted as well known. To recall the characteristics of the method we may perhaps paraphrase Dr Percy's meaning by describing the process as a special method for the smelting of lean or dry silver or gold ores, which do not contain sufficient lead or copper for these metals to act conveniently as collectors of the precious metals. The operation is conducted in a blast furnace, with an amount of carbonaceous fuel sufficing to produce an exclusively reducing atmosphere, and with the addition of pyrites, in order to form a regulus in which the precious metals shall be concentrated, the pyrites themselves being either argentiferous, auriferous, or cupriferous, or any combination of these three, or wholly barren of metal values. In the common acceptation of the term, it is understood that the use of the reverberatory furnace is excluded.

Jan 1, 1994

By Jianmin H, Shuqin L

This paper analyses problems associated with cement based technique in metal mines, and provides a new mining technique of packing the tailing sand and water into solidified material. In the new technique, the cementing agent is a solidifying material containing a high percentage of water and tailing sand. The sand and water solidify into the packed body at the same time. The slurry of the packed body varies widely in concentration and suitability for different mining conditions. It consists of two liquid materials, each composed of a cementing agent, tailing sand and water. The thick liquids are transported to the packing place at the same time. Their pumping property is good; they do not solidify or block up the pipe during transportation. At the packing place, the two liquids are evenly mixed.The mixed liquid flattens out well and its solidifying speed is so fast that it solidifies into a packed body within a very short period of time. The compressed strength of the packed body can reach 1.2-5MPa in one day, which satisfies the requirements of different mining conditions. By using the new mining technique, all the tailing sand can be used again in the packed body and it is low in cost and investment. The mechanisation is easy and thus the working efficiency is increased and the use of labour decreased. Contamination problems caused by i. Dr & Prof. Beijing Graduate School, China University of Mining Science and Technology,Beijing,China 2 Northern .Jiaotong University, Beijing,China 3. Beijing Graduate School, China University of Mining, Science and Technology

Jan 1, 1992

Mining is a high risk, high capital and potentially high reward undertaking. A large proportion of the risk comes from a lack of definition of the orebody (which also provides some of the potential) and the unpredictable nature of the market. This makes the planning process difficult but encourages the development of a robust yet flexible mining system. The system should be capable of absorbing some deviation from the anticipated concept without a significant impact on profitability. The mine planning process tends to consist of a series of related but discrete stages. For instance, the pit shells are designed, a schedule for the pit shells is created, a plant fleet is chosen to achieve the schedule and a financial analysis is carried out on that scenario. It is likely a few iterations are carried out using various mill throughputs to produce a favoured financial result. The problem is that handing results from stage æBÆ for use in æCÆ doesnÆt encourage a flexible system. æCÆ is likely to be built for exactly æBÆ. Unfortunately, in mining, æAÆ (the orebody) has the highest potential for variability and impacts everything else downstream. æDÆ the market also has high potential for unplanned variability. These variations can spread and æreverberateÆ through the whole mine process. For example an unexpected increase in ore oversize impacts all downstream mine processes to the primary crusher which may in turn create problems back æupstreamÆ by restricting throughput rate. Also an unexpected drop in demand or price could require modifications to the planned production rates. This paper looks at how mining process simulation can be used to support the development of strategies to counteract unforseen circumstances or alter production to match fluctuations in demand and price.

Jan 1, 2003

By Mudge S. T

Tin mineralisation occurs at Renison Bell, near Zeehan in Tasmania, as a group of cassiterite-bearing massive pyrrhotite bodies in Cambrian sedimentary rocks. Mineralising fluids from the underlying Pine Hill Granite have replaced carbonate rocks with massive sulphides and cassiterite. The discrete blocks of massive pyrrhotite have high density and high magnetic susceptibility contrasts with the comparatively barren country rock. They are strongly remanently magnetised and are excellent geophysical targets. A detailed geophysical model of the mine was created from a database comprising 1:2500 scale geological mapping and geological logs of approximately 4000 drill-cores. The model comprises 93 parallel cross-sections, each 1.5 km long, spaced 20 m apart. Each cross-section is comprised of up to 150 polygons which represent all known individual rock types and orebodies. The magnetic response of the model was computed and the residual between the model and the observed response, measured by a low-level helicopter magnetic survey, revealed several anomalies unaccounted for by the model. Drill testing of these anomalies led to the discovery of several hitherto unknown massive sulphide occurrences. Surface gravity data of the mine and surrounding district were enhanced by applying digital terrain corrections. The corrected Bouguer anomaly revealed a hitherto unknown positive anomaly associated with the ore zones of the Renison mine. The gravity anomaly of the model was also computed. Unfortunately, the limited resolution of the observed data prevented the delineation of ore targets. The terrain-corrected Bouguer gravity data were also used to model the shape of the underlying non-magnetic Pine Hill Granite. A computer inversion method was implemented to build a 3D block model of the granite. Results agreed with previous conventional 3D modelling techniques but yielded improved resolution of the granite form. The project involved development of new computer software to build and edit the large and complex 3D geophysical model of the mine and to compute the model's magnetic and gravity responses. Software was also developed to build and compute the gravity response of a 3D block model of the underlying granite.

Jan 1, 1997

Mt. Whaleback, the property of the Mt. Newman Joint Venturers, contains more than one thousand million long tons of high grade hema- tite averaging 64% Fe, ranging from 70%, the grade of absolutely pure hematite, to 54%. The ore occurs in the Dales Gorge and Joffre Members of the Brockman Iron Formation. The interbedded shale bands common in other orebodies occurring in these horizons are seldom more than a few inches thick and are commonly partially enriched to about-35% Fe. In the generally hard, massive hematite orebody, the gangue minerals tend to break preferentially to the fines, or -6 mm product, and for this reason it is of a somewhat lower grade than the lumpy product. The control of the chemical qualities is concentrated on the fines product for it has been found that maintaining the iron and alumina levels in this product ensures that all chemical specifications are met in both the lump and fines products. Physical qualities are monitored to ensure that the physical quali- ties of decrepitation and degradation of the lumpy product are maintained at levels accept able to the buyers.

Jan 1, 1973

By H Rose, T J. Sheer, M Dumka

Whenever rock is tipped from above, severe eruptions of airborne dust occur into the airways connected to tipping stations of rock passes (ore and waste) on the lower levels of a gold mine in the North West Province of South Africa. An investigation was undertaken to understand the nature of the physical phenomenon, in order to propose possible solutions. Accordingly, measurements were taken underground, involving the simultaneous logging at two levels of the transient pressures produced in the orepass by tipping from various levels. Two portable data loggers with associated transducers were custom-built for this purpose. Measurements were taken during a tipping program in which rock quantities and levels were controlled. Pressure pulses that are generated by the falling rock drive the airborne-dust eruptions. When tipping from a specified level, recorded pressure pulse waveforms were found to be repeatable on any given level, irrespective of the amount of rock falling, but measurements were conspicuously different on different levels. It was recognised that a pressure pulse is generated as the falling rock passes through the constricted region û a relatively narrow neck û at each tipping station. In passing through the constricted areas the mass of falling rock acts as a æleaky piston in a cylinderÆ and compresses the length of the air column in the orepass below that level. Once the rock has passed through the constriction, the pressure is released and this behaviour causes a regular train of pressure pulses that are separated by the time taken for the rock to move from one level to the next. Based on this physical understanding of the dust eruptions, a computational model has been developed that can reproduce all the main features of the measured phenomena. The model has been verified adequately against the measurements and can now form the basis for simulating a range of possible engineering solutions.

Jan 1, 2005

By T Ross, S Cameron

The requirement to use explosives in ground temperatures exceeding 50¦C is becoming more common as mines work to maximise the recovery of their resources. Orica Explosives was requested to assist in the development and implementation of æhot blastingÆ safe working procedures at Liddell Coal Open Cut in the Hunter Valley. The mine operator, Hunter Valley Earthmoving (HVE), had to contend not only with elevated temperatures in their overburden resulting from burning coal beneath, but also old underground workings which tended to exacerbate the problem. The paper discusses the following issues:the consultative process that was used to develop the procedures employed to ensure the process could be carried out safely; the technical issues surrounding blasting in hot ground, including temperature monitoring, product selection, application and design to ensure safety and performance were maintained; the need for confidence and trust in the team that was working together in a potentially hazardous environment, the emotive issues that were encountered and how they were addressed; the value of a regular review process combined with open and honest communication to ensure the procedures represented best practice and that all stakeholders understood the process; and the value delivered to Liddell Coal when sterilised areas of coal became accessible with little disruption to the mining process. The paper also discusses the challenges that were encountered in the Reservoir Block where proximity to major power lines and rail infrastructure meant that hot blasting procedures had to also consider vibration limits and the need for Energy Australia to disconnect the power.

Jan 1, 2001

The link between exploration success and new ideas from research and development (R&D), although often assumed, is rarely well explained or well illustrated. One issue is understanding the role of innovative ideas in the exploration process, and another is determining the relative contributing factors to an exploration success. A useful measure of gold exploration success over an extended time period and geographic area is discovery rate (θ): Discovery rate θ = gold discovered/exploration expenditure (usefully expressed as tonnes of gold per $1 million). The total gold discovered is strongly leveraged to discovery rate, as any increase in θ typically has a positive effect on exploration expenditure. Hence, improving the discovery rate is a key driver for a sustainable mineral industry, especially for gold. There are very few ways to influence θ beyond innovative R&D ideas and breakthroughs, and well-motivated and trained staff. The Australian gold industry has experienced exceptional exploration success with 9956 tonnes of gold discovered from 1979 to 2003, inclusive. This equates to: Discovery rate θ = 0.9 t/A$1 M Two-thirds of this gold has been found in the Yilgarn craton of Western Australia (6265 tonnes Au). Without this exploration success, there would have been no platform on which to build the current gold industry and to take advantage of elevated gold prices and advances in mining and processing. Several causes of the Western Australian gold success have been proposed, and more than one may be correct. Gold price, and mining and processing advances have all had influence; but exploration success and discovery of gold were essential to add to the miniscule resource base of 1979. A comparison of the exploration methods used to search for gold in the Yilgarn craton in 1979, and 1990, highlights a small number of breakthrough ideas introduced to the industry during the 1980s, and in most cases emanating directly from local R&D. By the 1990s, these ideas were being used in most gold exploration programs in the Yilgarn craton, and are still used today. These six breakthroughs are: epigenetic timing of gold deposit formation (ie after formation of rock sequence), chemical and mechanical role of host rocks, relevance of carbonate alteration haloes, gold dispersion in the regolith, optimal sampling media, and appreciation of landforms in exploration program design. Interestingly, gold exploration science in Western Australia entered the 1980s period without rigid paradigms in place regarding gold deposit formation; there was a balance between descriptive and genetic models, there was scope to research gold deposits from microscopic to global scales and there were highly effective industry research uptake processes in place: it is suggested here that these favourable conditions contributed to the exploration success and industry growth.

Jan 1, 2007

Access roads for haulage, construction or maintenance purposes are discussed with particular attention being given to the un- sealed "all weather" form of construction for Off-Highway applications. The service conditions experienced by the surfaces used in these roads is examined. These conditions are discussed in terms of the conventional engineering properties used for natural gravel material selection. Experience gained during the construction of a pipeline access track is used to illustratE material selection guidelines based on geological input and an understanding of good construction practices. TMITDnIll IrTT Ohl In many Australian situations off-highway haulage by wheel or track supported vehicles is carried on unsealed, gravel roads. Although the unsealed gravel road is the back-bone of the rural road network in Australia, in general, traffic loadings are relatively low compared to the off-highway unsealed haulage road. The cost of the haulage/access road construction component is one important factor in project planning which needs careful consideration. It is no longer acceptable that the initial rough exploration track be gradually upgraded so that it will eventually carry construction and maintenance traffic safely and efficiently. Fatal accidents and

Jan 1, 1982

The experiments described in this paper were carried out as a preliminary to a comprehensive study of the factors which affect the behaviour of lead during and subsequent to deformation by rolling and pressing. These observations are therefore to be considered as introductory to a further paper dealing more specifically with the above-mentioned variables.EXPERIMENTALThe rolling was carried out in a small mill with six-inch diameter surface ground rolls, both of which were electrically driven at 15 r.p.m. The average draft per pass approximated 0·03 in. The pressing was performed between platens in the compression unit of a 30-ton Amsler machine. The flat faces used had a ground finish comparable with the surface of the rolls. All hardness measurements were made with a Herbert "dead load" Brinell machine. The following te'sting conditions were maintained: ball diameter-5 mm.; load-10 kgms.; duration of loading-30 seconds; temperature of testing-16 to 18°C. The hardness values which are given are the mean of two or more impressions made at corresponding positions on the test specimens.PREVIOUS WORKSince the researches of Tresca (1):j: into the nature of the plastic flow of metals during various forging and extrusion...

Jan 1, 1939

By Mernagh T, Large R. R, Ryan C. G, Huston D. L

The Tennant Creek goldfield is one of the largest gold producing districts in Australia, and major deposits, including Gecko, Juno, Orlando, Peko, Warrego, Nobles Nob, Golden Forty, Argo, TC 8 and White Devil have produced more than four million ounces of gold over the past two decades. Gold-copper-bismuth mineralisation at Tennant Creek occurs in lenticular, ellipsoidal or pipe-like bodies of magnetite-hematite ironstones which are hosted in turbiditic sedimentary rocks of Proterozoic age (Large, 1975; Wedekind, Large and Williams, 1989; Le Messurier, Williams and Blake, 1990; Morrison, Donnellan and Hussey, 1992).

Jan 1, 1994

By Adhikari G. R, Raju N. M

The breaking of rock by explosives occurs so rapidly that the details of the phenomenon cannot he observed by the unaided eye. High resolution cameras and VCRs offer a means of slowing down the blasting action. A high resolution super video camera with digital zoom and a variable shutter speed was imported and used for the first time in India as a tool for blast optimisation studies at Malanjkhand Copper Project. Slow motion play-back revealed that the gases vented out through the fissures. The crest moved prior to the lower portion of the bench when initiated with detonating cord. The delay timing between the rows was not enough to provide sufficient relief and rock movement. This inadequate delay timing resulted in flyrock from the back rows. Stemming ejection was observed from practically all the holes. The muck profile was not satisfactory. A trial was carried out using 450 ms in hole delays and 25 nis surface delays. The front row holes were drilled based on the observations made from the laser profiling survey system. The video of the monitored blast showed that the rock started moving prior to the stemming ejection. It could be clearly seen that the entire block was completely initiated through the surface delays before the onset of the burden movement, thus eliminating any chance of misfires. Viewing blasts in high quality slow motion was useful to arrive at modified design parameters, resulting in uniform fragment size distribution and controlled rock movement.

Jan 1, 1995

A formalised approach to risk management has been regulated in the United Kingdom (UK) since the Construction (Design and Management) Regulations 1994 (CDM) came into force in 1995. These regulations have recently been revised in 2007. In response to a series of significant claims around the world the UK insurance industry published a code of practice for risk management of tunnels in 2003, and that was followed by an international version in 2006. Probably one of the main contributions of this new approach is the recognition that health and safety risks can best be addressed early in the process, initially by the owner and then by the designers. One of the aims is to achieve elimination of risks by good design. The advantage of a risk-based approach to tunnel design is that all risks are considered explicitly, and any residual risks in the design are communicated clearly to the construction team. This paper looks at the implementation of this formalised approach to risk management with reference to the A3 Hindhead Project. The design has been undertaken in accordance with the requirements of the CDM regulations, and also in compliance with the Joint Code of Practice for Risk Management of Tunnel Works in the UK. An outline of the risk-based design process used is provided, including examples.

Jan 1, 2008

After the minim operation, most raw materials that occur in the earth's crust require some form of processing or refining before they can be converted into a final end product. In the mineral industry these remarks apply to materials such as iron ore, bauxite, limestone, copper ore and many others that are found in Australia in large quantities. Processing plants for these raw materials operate more efficiently, however, if the feed to them is consistent in both physical and chemical characteristics. Such uniformity rarely occurs in nature so that some form of homogenisation, or blending, is required ahead of the processing plant. Bending also assists the mining operation itself by reducing; the need for selective mining and, by combining high and low grade materials, a more uniformly graded, commercially acceptable product can be obtained, thereby increasing the commercial life of a mine or quarry. Bed blending is the most efficient of the processes available, and following its development in the United States in 1905, over 100 plants have been installed, or are under construction, all over the world. The original process, the Robins--Nessiter system, has been the subject of continued improvements and refinements, so that economical capacities are possible from less than 100 l.t.p.h. up to 10,000 l.t.p,h. and beyond.

Jan 1, 1969

By Y B. Kang, Y J. Park

Ti-added ultra-low carbon (ULC) steel is produced by adding Al and Ti during the secondary refining process to deoxidise molten steel and to bind C and N which are detrimental to the deep drawing quality of the steel product. However, the production of Ti-added ULC steel faces challenges, including submerged entry nozzle clogging and surface defects on cold rolled coils. The troubles were often attributed to ‘Al-Ti complex inclusions’ in the molten steel. However, the evolution of oxide inclusions including their stability has been still unclear. In the present study, the evolution of these inclusions in Ti-added ULC steel was investigated by phase diagram measurement, CALPHAD thermodynamic modelling, high-temperature stability test for the oxides, and observation of transient behaviour of oxide inclusions in the steel. The phase diagram of the Al-Ti-O system was elucidated with an emphasis on oxygen potential, which significantly controls the stability of the oxides. CALPHAD thermodynamic models and a self-consistent database were developed. The transient behaviour of Al-Ti complex inclusions in Ti-added ULC steel was observed in situ using a confocal scanning laser microscope. This was additionally validated by the new thermodynamic model. The equilibrium phases of the oxide inclusions were investigated using a high-temperature resistance furnace, and were analysed using a secondary electron microscope, energy dispersive spectrometer, and electron back-scattered diffraction. By considering the morphology and crystal structure of these inclusions, the evolution of Al-Ti oxide inclusions was elucidated. Various behaviour of Al-Ti inclusions and their influence on steel cleanliness are discussed.

Aug 21, 2024

Unnamed early prospectors panned gold from creeks drain- ing the Great Dividing Range in the early part of 1851. The first publicised discovery was credited to Edward Hargraves near Bathurst in New South Wales later in 1851 and during the ensu- ing gold rush, prospectors rapidly made discoveries elsewhere in New South Wales and later across the border in Victoria. Reference to the attached graphs of gold production indicates that for much of the first 100 years, gold production came from the easily worked and readily discovered shallow alluvial deposits, many of which were located in the creeks draining mountainous regions of Victoria, New South Wales and Queensland (Fig. 1 and 2). As these deposits were exhausted, prospectors turned their attention to outcrop lode deposits which led to the development of underground mining techniques and a significant boost in over- all gold production. With the discovery of the rich Golden Mile lodes in Kalgoorlie in 1893, gold production increased signifi- cantly and peaked around the turn of the century. At that time, the enormous potential of the great Witwatersrand deposits in South Africa had only just been appreciated and for a few years, Australia led the world in gold production (1855-1863 and again in 1903). Underground mining continued in the Eastern Goldfields area of Western Australia, the Bendigo-Ballarat region of Victoria and in northeast Queensland. Very few of these operations continued beyond the Second World War, except the larger producers in the Kalgoorlie region where recovered grade had dropped to about 6 g/t Au. By the early 1970s with the gold price fixed at US$35 per ounce, most of the operations were shut down as labour costs escalated, with only the low cost bulk mining operation at Mt. Charlotte and the high grade reefs at Norseman continuing in Production.

Jan 1, 1988