Search Documents

By J Santana, V Ferraz, G Pinto, G Cruzado

Morro Agudo is an underground zinc and lead mine owned by Nexa Resources. The mine uses room and pillar as the main mining method. The recovery of pillars as well as the opening of new excavations using sublevel stoping as mining method has been studied. On some occasions, the need to recover pillars and open a stope by using the sublevel method happens in a region that is already excavated or in deeper areas than those mined so far. These changes represent a major geotechnical challenge due to the complex openings of the mine and interaction between two different mining methods. Historically, geotechnical mapping, kinematic analysis and a 2D numerical model were used to evaluate the new mine openings, and in 2021, 3D numerical model was introduced, which enabled global and local assessment of new excavations impact and the stability of openings after recoveries. The 3D model, made with MAP3D, is used to evaluate each pillar to be recovered, considering the spans of the resulting openings, the ideal sequencing of removal to maintain stability, in addition to the impact and geometry of the pillars left in the chambers. Pillar recoveries done in 2021 and the impact of it on the pillars left were the sources of the back analysis to calibrate parameters inputted on numerical model to assess recovery on new chambers and Phyllite has been considered into the model and it has been a source of instability due to its parallel position to roof of room and pillars and stope hanging walls.

Nov 29, 2022

The purpose of this paper is to outline the basic policy problems for good community relations programmes in the resource extraction industries of Papua New Guinea. The main focus of the paper will be on defining and analysing those problems which lie on the landowner side and which are still not widely understood within the resource extraction industries despite several decades of turbulent experience. Many of the companies operating in the resource extraction industries of mining and petroleum and gas have in recent decades adopted, by choice or necessity, 'good corporate citizen' policies. Some of these companies now pursue ethical business, environmental and community relations policies. Some have adequately funded and well-trained staff in their community relations departments. Although different industry sites scattered over Papua New Guinea show significant differences in their experience of social conflict, I argue here that a good deal of this variation has less to do with the differences between the companies' public relations policies and their effectiveness and more to do with the conflict causing features of indigenous society. Experience suggests that even a company well-equipped with good intentions, good policies and good staff may experience serious difficulties in maintaining good community relations in Papua New Guinea. Many of these difficulties, I argue, can be traced to causes that lie, essentially, within the structure of Papua New Guinean communities and in the customs and social relations of Papua New Guinean peoples. Accordingly the attention of this paper is focussed on the conflict causing aspects of Papua New Guinean society. It is true, to the point of being a cliche, that Papua New Guinean societies are oriented very strongly towards achieving consensus and social harmony. In this regard Papua New Guinean communities differ significantly from, say, Australian communities. My purpose here is not to denigrate this aspect of Papua New Guinean societies but, rather, to point out that the drive for consensus is driven by the desire to avoid its opposite, dissensus. This paper sets out to define the dissensual aspects of Papua New Guinean societies and my special interest is in those conflict producing aspects of Papua New Guinean societies that are most resistant to the mechanisms that are designed to create social harmony. A survey of the recent history of industry and community relations in Papua New Guinea indicates that there are three main factors present on the landowner side which are liable, separately or through their interaction, to cause difficulties. These factors are respectively generational challenge, social boundaries and custom variability and I shall discuss each of these in turn.

Jan 1, 1997

By Lawrie DC

Finely ground beryl was decomposed by mixing with ground limestone and soda ash andheating at 900¦C for,4-6, hours.The sintered material was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hours. The liquor containing Be, ; Al, . Fe and, other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either' by filtration or by decantation washing.The clarified leach liquor.was first treated to remove Fed}: , by contacting with a primary amine-kerosene solution in2 counter-current stages. The iron free liquor wa,s then passed to a 4-stage counter-current extraction unit where it was con-tacted with 0.5M di-(2 ethyl hexyl), phosphoric acid (EHPA) in kerosene. The'operating conditions were such that at least 99 p'br cent of the Be and only 7' per' cent of the Al- was, extracted The ,B6`= and. Al were ;stripped from the organic phase by sod-ium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipTitated a's Bo(OH)2 by-hoating the alkaline solution to 90C, the Al remaining in solution. After filtra-tion and washing, the Bo(OH)2 could be ignited directly to BeO at about 1000 C or used as a feed to further purification stages aimed at producing "nuclear grade" BeO.A small coaAter-current extraction unit was operated con-tinuously using liquor derived from the sintering and leaching stages. Data obtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precip-itate contained more than'99 per cent BeO.

Jan 1, 1963

By Y H. Zhu, X X. Tang, Y C. Yin, M L. Xing

Based on the stiffness theory, the stiffness difference and energy supply of surrounding rocks are important inducing factors for strain burst. However, due to the lack of multi-level low stiffness testing machine, there are few experimental studies on rock failure mechanisms under the influence of loading stiffness. This paper introduced a self-developed rock testing system with changeable stiffness. The main testing machine of this system is a combined structure of inner and outer frame. The change in the loading stiffness is achieved by using a stiffness servo control system to control the energy accumulation in the inner frame. The tests of the sandstone specimens under three different loading stiffnesses in the testing system showed that the loading stiffness did not significantly affect either the uniaxial compressive strength or the Young’s modulus of the rock. However, the post-peak stress-strain curve of the rock became smoother and steeper when the loading stiffness was decreased, and the stress drop rate increased. It is shown that the stress drop rate had a power function correlation with the loading stiffness. After the peak load, the inner frame of the testing system rebounded several times at high speeds. The magnitude of the instantaneous rebound speed and the rebound duration increased with the decrease of loading stiffness. Both the mean rebound velocity and the total rebound deformation had power function correlations with the loading stiffness. The loading stiffness has limited effect on the energy storage and energy dissipation characteristics of the specimen, while the released energy of the testing machine increases as the loading stiffness decreases, which is the key factor affecting the failure mode of the specimen. According to the test results, a rock burst mechanical model considering the stiffness is established, and the energy supply mechanism of rock burst is quantitatively explained.

Nov 29, 2022

By McIlveen GR

The water pollution hazard posed by the derelict Conrad mine site, to the water and associated stream sediment of Borah and Maids Creeks and the nearby Copeton Dam storage, has been assessed. Mine water, tailings and tailings dump leachate have polluted water and stream sediments in Borah Creek downstream of the mine site. Acidity, arsenic, copper, lead, iron, silver and zinc are the principal pollutants. Under dry and low flow conditions, mine water was found to be the dominant polluting source, however, leachate and run-off from tailings dumps were also significant under and following wet conditions. Soluble arsenic, lead, iron and silver species in mine water and leachate were found to be rapidly incorporated into sediments, but acidity, copper, and zinc persisted in the creek water. Under low flow conditions, the water of Maids Creek is polluted with copper and zinc (up to 4.4 and 34 mg/l for copper and zinc respectively) and the pH is decreased (from pH 5 - 7 to pH 3 - 6) by entry of Borah Creek water. Values found in Maids Creek were variable and related to flow regime and distance downstream from Borah Creek confluence. Water in Copeton Dam storage, having a much larger volume of water with a higher bicarbonate buffering capacity (50mg/l versus 15mg/1), is not affected by entry of Maids Creek water. Polluted sediment from Borah Creek has contaminated Maids Creek for 2km downstream to Copeton Dam storage. Stream sediment downstream of the Borah Creek confluence, contains up to 1.0% As and 1.4% Pb in the less than 200 micron size fraction. Under high flow conditions, arsenic was found to be moved out from the mine site as insoluble species, associated with suspended sediment in Run-off.

Jan 1, 1988

By B P. Voutharoj, R A. Dutch, M Paknezhad, T Ostersen

With the proliferation of new sensor technologies, acquiring multiple data sets over the same ground is becoming cheaper and easier than ever. This new, higher resolution multivariate data provides a significant resource for exploration and resource geologists but comes with the added complexity of effectively integrating the various data sets in useful and meaningful ways to elucidate new geological understanding. Both geophysical data sets and hyperspectral data are extensively used for exploration targeting, providing different information at different resolutions and crustal scales. One of the biggest challenges comes from trying to effectively integrate data sets that record very different physical properties, across the different scales these data are captured at, in a way which can allow for a data-driven analysis of these combined data sets.

Sep 1, 2024

By S Tjerry, S Szylkarski, B Willis-Jones, I Dubinski

Achieving relinquishment of mining sites is becoming increasingly difficult, with a study by Byrne (2013) estimating that out of a set of 73 mining and metals sites around the world, less than ten per cent had achieved relinquishment over the last 50 years. The median forecast duration of time allocated for water management in the closure plans studied was approximately ten years, while the reality at the actual sites was a median duration of 22 years to date and growing.One of many challenges in mine closure planning is managing geomorphic stability of stream diversions. The challenge is to be able to demonstrate to regulators and the community that a proposed rehabilitation solution will be stable over the long term.During the mining operations, local watercourses and surface drainage can be diverted and managed using engineered channels and drainage structures. However, during the post-operations stage, the engineered channel and drainage may require modification to a more natural condition that will facilitate long-term environmental sustainability. Achieving geomorphic stability of a diverted watercourse is difficult, with the majority of stream diversions in Australia failing to meet expected design performance (White et al, 2013). Geomorphic stability is a complex process that is controlled by a combination of factors, including hydraulic flow conditions, geotechnical conditions and vegetation.This paper proposes that a fully dynamic and deterministic geomorphological model can be used to supplement the traditional empirical approaches to assess long-term geomorphic stability. The paper provides an overview of the geomorphological models and how they have been applied in engineering studies for forecasting future evolution of stream systems. The paper discusses the potential application of these models in the mining industry for forecasting and optimising surface water structures for the operations and post-operations stages of the mining cycle.CITATION:Szylkarski, S, Willis-Jones, B, Tjerry, S and Dubinski, I, 2016. Improving the reliability of stream diversion designs in mine closure plans using a morphological tool, in Proceedings Life-of-Mine 2016 Conference, pp 212–215 (The Australasian Institute of Mining and Metallurgy: Melbourne)

Jun 28, 2016

The difficulty in screening of ores when the moisture contents reach certain critical levels has resulted in mining circuits using wet processes for screening. While this has been acceptable in past years it is no longer acceptable in certain countries and where the mining company is looking to reduce its impact on the surrounding environment.   Various mining companies have been looking at ways to remove the need of using water, with all its inherent drawbacks and to be able to produce its desired products in a dry process.   This would have the benefits of less environmental impact and cost, (due to not requiring wet processing equipment), less power consumption (reduced equipment needed), no corrosion issues, no contaminated waste waters and reduced maintenance activities.   Until recently this has proven elusive or with technical restrictions with current available acceptable technologies for high capacity plants.   One major mining company began seriously exploring ways to overcome this dilemma so that they did not replicate their current ways of operating for their new expansion plans.   They partnered with Metso Minerals to undertake extensive groundbreaking laboratory test work and provide potential solutions as to how to solve this. The laboratory test work proved interesting enough to design, manufacture and test on the actual mining site a prototype screening machine in the circuit.   This break through in screening technology reduces the environmental impact on the area in which the mine is located by: eliminating the storage and use of water, reduction in energy consumption due to having no pumps in the plant, reduction in plant costs and the upstream affects on the environment process used to manufacture and ship the materials the plant structure is built from, and no large tailings dams to take up land space and affect the environment through groundwater/ water table contamination and the negative effects on animals and ecosystems Laboratory test were conducted and a full size machine was installed at the plant site along side conventional machines. The screen size (2.4 m wide x 6.1 long double deck) was determined by the size of screens currently in operation at the mine. The parameters that were explored were: types of screen surface (polyurethane, woven wire etc), types of screen motion (linear, circular or elliptical), angle of motion ( 40,45,55,60 degrees etc), and throw (amplitude), speed and 'g' force.

Jun 1, 2010

The Ranger Project Area covers 78.6sq km and is approximately six km east-west by 14km north-south (Fig. 1). The area is known to con- tain two uranium orebodies, Ranger No. 1 and No. 3, two uranium occurrences, Anomalies 4 and 5 and three significant radon anomalies, Ranger 18, 19 and 48. The Ranger No. 1 and No. 3 Orebodies con- tain approximately 120 000 tonnes of U308 in highly chloritised metasediments of the Lower Proterozoic Cahill Formation. The orebodies occur as suboutcrop and exhibit significant radiometric anomalies. These occur within approximately 400m vertically of the projected unconformity with the sandstone of the Middle Proterozoic Kombolgie Formation. Oxidised and reduced uranium minerals occur in quartz-rich schists containing variable muscovite, chlorite and sericite and in the chloritic matrix of chert breccia. Secondary uranium minerals namely saleeite, metatorbernite and gummite associated with earthy iron oxides occur from the surface to 50m depth in No. 1 Orebody and up to 80m depth in No. 3 Orebody. Below the oxidised zone, uranium occurs as pitchblende finely disseminated throughout sequences of quartz muscovite chlorite schist up to 150m thick and as open space fillings in zones of structural deformation. The uranium-bearing schists directly overlie up to 300m of dolomite and magnesite containing minor interbedded schist units and are themselves overlain by approximately 2 000m of more micaceous schists of the upper part of the Cahill Formation. Regional metamorphism has occurred to at least amphibolite facies and has been followed by retrograde metamorphism to a greenschist facies equivalent. The metasediments are intruded by granitic pegmatites and dolerites. Uranium is associated strongly with chlorite of which there are at least five textural varieties. Not all of the various generations of chlorite have associated uranium. Graphitic schist horizons occur which are often less than one metre thick and discontinuous. These are best developed at the base of the quartz chlorite schist sequence where uranium grades up to 1 000ppm U may extend for several hundred metres beyond the main ore zone. Uran- ium is not common in the carbonate sequences and only occurs in chlorite segregations in disrupted zones. The unoxidised ore contains sulphides, mostly pyrite, which are low in abundance (

Jan 1, 1984

The overall mineral assemblage of the Broken Hill orebody is similar to that of a skarn. However unlike the classical skarns it does not represent contact metamorphism of pre-existing limestone beds. It is a stratiform accumulation of exhalative-sedimentary silica, sulphides, (Ca, Fe, Mn) silicates and carbonates, fluoride and phosphate that has later undergone regional metamorphism. The resulting development of coarse-grained quartz, sphalerite, galena, rhodonite, bustamite, mixed carbonates, fluorite, apatite and many minor phases has produced a sulphide-rich skarn- like mass that like many others of its kind, might best be referred to as a stratiform skarn. Recent investigations of occurrences of this type are showing that the incidence of concentrations of particular metamorphic minerals in and adjacent to such orebodies are closely related to bedding and to former sedimentary facies patterns. From this it appears that the mineral assemblages may be used to deduce not only the nature of the materials laid down in the beds, but also the physico-chemical conditions under which sedimentation took place. Several stratiform deposits, including Broken Hill, are used as examples to show that variations in these conditions may have a profound influence on the subsequent response of the rock to regional metamorphism and hence on the mineral assemblages that finally develop.

Jan 1, 1983

By B P. Banerjee, S Raval

In the recent past there have been dramatic advancements in the development of remote sensing platforms (satellite, aircraft and unmanned aerial vehicles – UAVs) as well as sensor systems (multispectral, hyperspectral, thermal, light detection and ranging (LiDAR) and radar). However, selection of the appropriate remote sensing technique for a mining application is complex and requires scrutiny on multiple scales including spatial, temporal and imaging capabilities. This presentation highlights various conventional and emerging remote sensing approaches over a mine’s life.CITATION:Banerjee, B P and Raval, S, 2016. Applications of advanced remote sensing systems during a mine life, in Proceedings Life-of-Mine 2016 Conference , pp 116–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

The purpose of the Lower Lea Valley Cable Tunnel project is to relocate the overhead power lines circuits, which currently cross the proposed site for the 2012 London Olympics in East London. This was the first contract to be awarded as an Olympic project and is on the critical path for the proposed Olympic Park as the construction of the Olympic village, stadium and other venues cannot begin until the tunnels are complete, the cables installed and the overhead power lines removed. The tunnelling works for the scheme include two parallel tunnels between Hackney and West Ham. Each tunnel is approximately 6 km in length. One tunnel is 4.15 m ID and connects the National Grid substations. The other is 2.82 m ID and connects the EDF Energy substations. The tunnels were constructed through mixed ground using four earth pressure balance tunnel boring machines. These were driven simultaneously from two drive shafts within a single site. The 12 km of main tunnels were constructed within a year from start to finish, with completion in June 2007. The shafts range between 6 m and 15 m ID. These were constructed using a combination of caisson sinking and underpinning techniques. Dewatering was adopted to suit the groundwater conditions.Other works include the design and construction of the head house buildings, cable and ventilation culverts, mechanical and electrical (M&E) installations and all associated works. In addition to the above, a further 1 km of tunnel and two shafts were added to the project scope connecting the EDF Energy tunnel to the substation at Bow. These additional works provided further challenges to the project to ensure that these works were constructed within the program constraints for the 2012 London Olympics. This involved refurbishing one of the tunnel boring machines from the main EDF Energy tunnel drives and relaunching the machine to construct the Bow tunnel. The Bow tunnel was constructed within two and a half months, with the tunnel boring machine breaking through in August, ahead of schedule. The main challenge presented by this project is the program constraints. This project outlines the requirement for team work between the client, stakeholders, contractor and designer in order to provide program certainty. A close working relationship between the contractor and the designer is required to provide value engineered, time-saving solutions to mitigate the risks associated with the design and construction program.

Jan 1, 2008

Driefontein Gold Mine together with Kloof Gold Mine and Beatrix Gold Mine forms part of Gold Fields South Africa. Driefontein Gold Mine is situated near the town of Carletonville, 50 km south of Johannesburg, in the Gauteng Province. The 4 Shaft East complex comprises of the 4 Main Shaft and the 4 Subvertical Shaft. The main shaft is 9150 m in diameter and was sunk in 1984 to a depth of 2000.5 m. The 4 Subvertical Shaft is 7320 m in diameter and was sunk during 1985 to a depth of 3006 m. Full production was, however, only reached during 1988. Intensive mining is currently being done between levels 28 to 42. In 2002 a decision was made to start mining the shaft pillar, situated between 32 and 33 level in the subvertical shaft. Intensive studies showed that with selective mining scheduling the total mineÆs life could be lengthened by nine years if accessed timeously. The higher grades present in the shaft pillar can be mixed with lower grades from the same reef band presently mined 1500 to 2000 m away from the subshaft pillar area. The shaft pillar comprises 50 per cent of the remaining ore resources available. However, no provisions were made in the initial phases of the shaft development to extract the shaft pillar. Grades between 4300 cmgt to 2500 cmgt relating to 23 and 14 g/t are present in the shaft pillar and an estimated 50 tonnes of gold can be produced from this pillar in the period from 2007 to 2015. The pillar extraction is the key to DriefonteinÆs long-term gold profile. Every geological feature possible is represented in this to-be-mined pillar area. The pillar around the shaft is a complex structure featuring hard and soft lava, sedimentary structures/plane parting that moves against each other, quartzite capping, etc. Replacement of services and secondary support systems were designed, modelled and put in place. The original steelwork was not designed to cope with the various stresses and movements, which are expected once the extraction process is started. Existing shaft steelwork was used as far as practically possible. The principal behind the design was that the steelwork would be totally disconnected from the shaft lining over its total length of 132 m in the area of the reef intersection. This will allow the steelwork to move independently from the geological structures surrounding it, allowing a certain degree of distortion of the shaft lining, moderate twist and tilt to take place without interfering with hoisting operations.

Jan 1, 2005

This paper gives the background to the development of solvent extraction processes for the recovery of metals from aqueous solutions. Its growing importance in Australia for the recovery of both uranium and copper is dis- cussed, as well as the developments in mixer-settler design as applied to recent plants. The economic significance of solvent extraction as an alterna- tive to cementation is discussed and important features of each process are highlighted by comparison of costs for each process in a hypothetical situa- Tion.

Jan 1, 1971

By Durucan S

The southern Attiki peninsula is a very interesting area from an environmental point of view. The port and the city of Lavrio is situated at the east coast of the peninsula with about 10 000 inhabitants and there are also a few villages in the vicinity. The south-eastern part of the peninsula hosts the famous Lavrio mines which exploited the silver bearing orebodies of the area for more than 25 centuries. As a result, soils around the city of Lavrio are polluted with high heavy metal loads. The area is also of archaeological interest, as there are well preserved remnants of ancient mining and processing plants and archaeological sites. Soil samples collected from an area of approximately 120 km2 around Lavrio were analysed for their metal contents and the spatial distribution of the concentrations of ten selected elements were estimated from these data sets. The spatial data analysis and transformation capabilities of Geographic Information Systems, combined with extensive mining and geological data, helped the authors to identify the extent and causes of metal pollution around Lavrio.

Jan 1, 1995

The establishment of vegetation onto open cut mine spoil is dependant on the nature of the soil and rock strata of the overburden. Experience has shown that in the Bowen Basin of Central Queensland the nature of the minespoil changes considerably as subsequent and deeper mining strips intercept changing rock strata. The different mixes of strata at the surface of reshaped spoilpiles can produce variable response in the sown vegetation cover. It is usual that land features of mine sites are known in detail and are depicted on mine or locality maps. Subsurface strata and lithology descriptions are available and are used for planning of open cut mining operations. Surface and subsurface data can also be used to estimate the intrinsic nature of overburden through the use of fence diagrams. Lithology at points along a mined strip can be obtained and used to describe overburden. Indications are that correlations exist between salinity of overburden components and the response of vegetation. The developed procedure thus becomes a useful tool for the prediction of revegetation Practices.

Jan 1, 1987

This paper describes the MillMapper technology developed for condition monitoring of liners and other operational parameters in grinding mills used for mineral comminution, by presenting a case study of its application. MillMapper provides maintenance engineers, operations managers and process and plant metallurgists with quantitative, accurate and reliable condition monitoring data for informed decision making regarding the maintenance and metallurgical aspects of such mills. MillMapper uses calibrated laser scanners for the capture of three-dimensional surface representations inside a mill during a shutdown so as to determine shell, feed and discharge liner thickness at a resolution of several million data points, a procedure that nominally takes five minutes to complete. Once several data sets over time have been collected inside a mill, MillMapper can be used for liner wear, liner wear zone, liner weight, ball charge volume, ball charge weight and intelligent profile tracking over time. Liner tracking in combination with site defined reline and failure criteria and with throughput tonnage data is utilised for change out prediction of each separate liner segment type.

Jan 1, 2008

By J J. Frausto, G R. Ballantyne, M S. Powell, R Cruz, K Runge

Hydrocyclones are the most widely used device for classification in a grinding circuit. However, even the most efficient hydrocyclone has a bypass of fines from the feed to the underflow which reduces comminution circuit performance, as well as misclassification around the cut point. Fine screens classify only according to the particle size, allowing for a reduction in the recirculation of fines back to the mill. The development of high capacity multi-screens makes fine classification in a grinding circuit a viable option. Minera Saucito recently substituted hydrocyclones with screens in its grinding circuit. The change of classifier resulted in an increase in throughput and lead recovery but a decrease in silver recovery. This case study presents the changes in comminution and flotation performance that occurred after the installation of screens and uses historical operational data collected over 12 months of operation to investigate the reasons for these observed changes. CITATION:Frausto, J J, Ballantyne, G R, Runge, K, Powell, M S and Cruz, R, 2017., in Proceedings MetPlant 2017, pp 298–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Durucan S

Uncertainty due to spatial and temporal variability of different pollutants found in soil, water and air is an important issue in the modelling of environmental impacts. Recognition of spatial environmental patterns is relatively straightforward to achieve by applying most of the well-known artificial neural networks or adopting a stochastic approach. However, it is the temporal component of the environmental variables that makes modelling of the environmental pollutants particularly complicated and challenging. This paper presents the results of a case study investigating the artificial neural network performance when modelling the spatio-temporal behaviour of environmental pollutants. The test case involved the modelling and prediction of the distribution of water quality indicators along a river from the point of discharge of treated mine effluents. The behaviour of river water quality indicators is rather complex and shows a lot of fluctuations due to a number of hydrochemical, hydrobiological and hydrodynamic factors. Results obtained in this study indicate that artificial neural networks provide a very powerful and robust method for simultaneous modelling of spatio-temporal behaviour of environmental pollutants.

Jan 1, 1995

By B Chappell

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to be placed in a tailings dam. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electroosmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998