Search Documents

By E J. Coyle, L A. Millington

Tailings storage facilities are geotechnically complicated structures that develop heterogeneous strength profiles and varied porewater conditions. The monitoring of porewater pressures is one of the only direct measurements that can be performed to monitor the performance of a facility throughout its life and is of particular importance in upstream facilities. Foundation underdrainage, continuous and staged tailings deposition, climate inputs (rain, snow, humidity, evaporation, etc), and stratified tailings permeabilities can complicate this critical measurement that introduces uncertainty to stability analyses. These difficult conditions manifest in vibrating wire piezometer measurements as very low or negative pressure readings, both of which are within the instrument’s range of accuracy. However, the data can be difficult to interpret, and a range of interpretations are adopted from optimistic low phreatic surfaces to conservative fully saturated tailings. Where tailings are potentially liquefiable, these very low readings introduce further uncertainty regarding the pore space saturation ratio and liquefaction potential above the estimated phreatic surface. This area of uncertainty is the vadose zone, and its affect on tailings behaviour is not well understood. The two facilities analysed in this paper are upstream, raised embankments with tailings classified as clayey, sandy silt that have been found to be potentially liquefiable. The vibrating wire piezometers (VWP) at both sites show very low or negative readings when they are initially installed near the surface and then go through cycles of re-saturation and de-saturation. Eventually the readings settle as the VWPs are buried deeper within the tailings. The instrumented sections within the tailings column do not show consistent readings that would be indicative of a hydrostatic phreatic surface at either site. Rather, they are highly variable and can be interpreted as either representing a high phreatic surface within the tailings or as a ‘perched’ phreatic zone within the tailings layers. How the VWP data is interpreted has a significant impact on how the facilities are raised and operated. The design outcome for Site 1, which adopts a lower phreatic surface, results in an embankment that meets factor of safety (FoS) requirements under residual strength conditions without any buttressing. Conversely, a conservative (high) phreatic surface has been adopted for Site 2 and has resulted in the facility requiring a significant buttress to meet FoS under residual strength conditions.

Jul 1, 2021

By N Clarke, J Hunt, A Barros, N Guerrero, L Keeney

Grade Engineering® (GE) involves a range of integrated technologies and operating protocols for improving effective feed grade through early rejection of low value material prior to costly processing activities and has the potential to transform the economics of large, low grade, mining operations. Extensive GE test work by AngloGold Ashanti (AGA) and the Cooperative Resource Centre for Optimising Resource Extraction (CRCORE) determined that the Gramalote gold deposit in Colombia is highly amenable to implementation of grade-by-size screening to upgrade the ore at a production scale. To understand the relationships between geology and the upgrade response drill core and bulk samples were analysed at the Centre for Ore Deposit and Earth Sciences (CODES) as part of a larger CRCORE project to understand geological controls on grade-by-size deportment, i.e., the tendency for specific mineral phases to preferentially fractionate during breakage into different size fractions. This work is focussed on understanding the role of mineralogy and texture in influencing rock breakage and natural fractionation at a range of scales. Detailed logging of Gramalote drill core and mineralogical analyses including hyperspectral logging, portable and bench-scale X-ray fluorescence (XRF), plus low resolution Laser Ablation of intact drill core pieces, combined with data from site (drill logs, geochemistry, petrophysics) were used to evaluate the ore and alteration mineralogy, vein paragenesis and textural variability. This provided information on gold deportment and allowed the identification of favourable host veins. Bulk sample material from different ore grade zones was also analysed. A comparison with the results of GE testing shows that positive upgrade results are produced by rocks with abundant veins, particularly those associated with potassic and/or white mica alteration. This work indicates upgrade response can be predicted from drill core using data collected by a combination of automated systems including hyperspectral data, XRF, and detailed drill core logging.

Nov 10, 2020

By McLennan R. G

Mr. F. Cavanaugh (E.R.S. Co. of Aust. P'ty. Ltd.) ; What is your opinion of the expendable gauze type respirator? Would you give your views on what type of training is most effective to improve the safety consciousness of "new" New Australians?Mr. Lewis: For many jobs, the expendable gauze respirators are quite satisfactory. However, where silica dust of less than 10 micron sizing is present, they Cannot be recommended. Generally, they are more acceptable to the men than the heavier but more efficient types of industrial respirator.The best avenues of approach to training appear to be:(a) Liberal use of vi~ual aids (posters, photos, slides, etc.)(b) Efficient interpreter service.(c) Constant follow-up and check by foreman and fellow workmen.Mr. W.Marsden (B.H.P. Collieries); Most colliery employees only wear masks when they can see dust which, of course, is not the hazardous dust, and they take the mask off when they can't see the dust and so expose themselves to the hazard which is often present.Mr. W. W. SoIIy (S.A. Mines Uranium Treatment Plant) ; Safety equipment as supplied by manufacturers is inefficient and short of safety and common sense requirements-operators don't wear equipment because it is uncomfortable, clumsy, or unsightly. In the case of face masks,* they are not completely, effectively sealed; hard hats should be made even lighter and yet efficiently strong; concerning gloves, it seems not too much to ask of suppliers to put up a durable glove, preferably lined for comfort, with the maximum amount of "feel". Adaptation of, say, tubeless tyre methods...

Jan 1, 1958

Present value maximisation studies are a useful aid in enhancing the economic performance of open pit mining operations. Maximising present value helps to reduce the risk of financial failure. Maximisation of present value also means that the capital invested is being used most efficiently. A characteristic step in determining the present value of an open pit mining operation is to set out the sequence in which increments of material (ore of various grades and waste rock) are mined. Traditionally, present value maximisation has been performed by selecting a cut-off grade for each increment so as to maximise the present value of the total operation, by an iterative process using computers. Kenneth F Lane has developed a method and applied it to many mining operations. An alternative method for determining the maximum present value of an open pit mining operation is given. In this method the maximum present value is determined by working backwards from the end of the operation life, progressively asking the question of each increment `what cut-off grade maximises the the present value at the start of mining of that increment?' The method allows calculations to be performed by a `spreadsheet' package. Present value determinations are characteristically performed under constant conditions (eg prices, costs) throughout the operation life. Unfortunately real life circumstances are rarely constant, with the costs of mining inputs rising at variable rates. The prices received for mineral products have been shown to broadly trend downwards with time in real terms. Treatment of such changes in the determination of the maximum present value of an operation is discussed.

Jan 1, 1994

Much has been written about leadership over the years. It is probably one of the most written about but least understood and defined concepts in business. Leadership and management are often confused and blurred, and inspirational words such as mentor, coach, motivator and the like, are often interspersed when describing a leader. There are a few things we do know about leadership:The only thing common to all leaders is that they are different.Leadership is not the sole domain of business; it applies to every aspect of human endeavour. We are all required to lead at times, and we all have it in our ability to lead. There is no set of predetermined competencies, which a leader must possess to be effective. Hence there is no course in the world that can teach you to become a leader. There is no such thing as the perfect leader. Leadership is a verb, not a title; you actually have to do it to be judged a leader. All leaders no matter how you define the term, must leave a legacy. Thus in the busy world we all live in, what are the lessons in leadership that we can all learn from, that will assist us all in our pursuit of leadership. The purpose of today is to put forward a framework for leadership that I have been researching and working on for many years. It is not the definitive framework, merely a framework. Out of today you will take your own collective thoughts, learnings, observations, experiences, education and training, and collective wisdom, and apply it to yourself.

Jan 1, 2004

Since the introduction of the Neil George Five Point Safety System, to the underground sections of The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines in March, 1969, the Disabling Injury Frequency Rate has been halved and shows signs of contin- uing to fall. The total accident frequency rate has also fallen, although the decrease has not been as significant. Before the introduction of the Neil George Safety System, analyses of the direct causes of accidents showed that approx- imately 25 per cent were caused by "unsafe conditions", while 75 per cent were attribu- table to "unsafe acts". Within twelve months of introducing the system, these percentages had significantly changed to 7 per cent unsafe conditions and 93 per cent unsafe acts. Today, the figures are 3 per cent and 97 per cent respectively, and these figures clearly show that the main emphasis in the current programme must be directed towards making the operating men safety conscious. The effort must be focused on changing the minds of men.

Jan 1, 1975

By Junpeng L, Huiguo Q

Field instrumentation was installed to monitor ground and lining behaviour during and after construction of the Mount Shaughnessy Tunnel (Rogers Pass Short Tunnel) in Canada. The instrumentation was placed in a soft ground section of the tunnel at its crossing with the Trans Canada Highway. The tunnel was excavated through a dense bouldery soil. Presentation of the field data and inter- pretation of the tunnel performance from a geological-geotechnical point of view form the basis of this paper. The loss of ground due to the tunnel excavation was found to be exceptionally small. This has been attributed to the unusually high strength and stiffness of the host soil. Evaluation using the Boundary Element Method, together with a simplified analytical technique, were applied to assess the relevant soil parameters and their influence on the tunnel performance.

Jan 1, 1987

By Thomson S, Eisenstein Z

Field instrumentation was installed to monitor ground and lining behaviour during and after construction of the Mount Shaughnessy Tunnel (Rogers Pass Short Tunnel) in Canada. The instrumentation was placed in a soft ground section of the tunnel at its crossing with the Trans Canada Highway. The tunnel was excavated through a dense bouldery soil. Presentation of the field data and inter- pretation of the tunnel performance from a geological-geotechnical point of view form the basis of this paper. The loss of ground due to the tunnel excavation was found to be exceptionally small. This has been attributed to the unusually high strength and stiffness of the host soil. Evaluation using the Boundary Element Method, together with a simplified analytical technique, were applied to assess the relevant soil parameters and their influence on the tunnel performance.

Jan 1, 1987

Many problems result when coal mine shafts are built in complicated geological conditions and serious shaft lining ruptures have often occurred in the eastern part of China since 1987. Grouting is applied as one of the major measurements for shaft lining ruptures. However, as the general location of reinforcement grouting for shaft lining is deep in or near the bottom aquifer, while using cement grout as the grouting material, the grouting mostly belongs to fracturing grouting in deep alluvium. In these conditions, the mechanism and behavior of fracturing grouting has not yet been understood. From these points of view, this paper describes the mechanism of shaft lining rupture and fracturing grouting and then discusses the effect of grout injection on the stability of shaft lining by means of numerical analysis and field data obtained so far.

Dec 6, 2010

This address is set deliberately in the broadest possible terms. A review of the place of mining in Australian life today will serve to point up the changes that we can see in the life of people in the industry. Some of the influences on the future welfare of mining people bear also on the progress of this Institute, now approaching its 90th year. As mining becomes more and more dependent on higher technology and therefore, on the higher skills of the people in the industry, the role of The Institute, I suggest, becomes more and more significant.With investment per employee in mining generally continuing to rise, our ability to handle problems of manpower and human relations becomes a matter of greater importance.Questions that flow from these general thoughts form the substance of what I have to say.

Jan 1, 1982

Mining and metals projects have tended to increase in both scope and cost to a point where many projects are Droperly designated as superprojects. Specialist engineer- constructors have developed organisations and systems to provide project management services during the design and construct phase of large projects. However, the engineer-constructor is also required to provide a wide spectrum of services during the evolution of large projects prior to the construction phase. Some common phases of pre-construction evolution are identified together with the associated types of specialised services which may be required. A project management team approach is described which has been developed for the design and construct phase. It is suggested that a modified matrix organisation could be adapted to the provision of special- ised services as well as to project management for ore-construction phases of the project.

Jan 1, 1980

The Nickel Rim Depth Cu-Ni-PGE deposit, discovered by Falconbridge Limited in 1993, illustrates several trends in exploration in the Sudbury area. Recent discoveries tend to be deep, high grade, footwall hosted, close to or straddle property boundaries and made using a multi-disciplinarian exploration approach that integrates economic considerations with geology, metal geochemistry and geophysics (borehole EM). The Nickel Rim deposit occurs down dip of Inco's Victor Deep deposit (4.2 million tonnes at 2.25 per cent Ni, 7.30 per cent Cu) in the eastern margin of the Sudbury Igneous Complex (SIC) at a depth of 2650 m. Before commencing drilling an economic evaluation was done to determine the minimum size needed to be economic at the expected depths and determine the expected value of an exploration venture. The subsequent surface exploration program discovered a drill indicated, undiluted mineral inventory of 1.6 million tonnes of 1.58 per cent Ni, 10.13 per cent Cu, 4.17g/t Pt and 3.50 g/t Pd including 519 000 tonnes of 4.13 per cent Ni, 25.53 per cent Cu, 9.76 g/t Pt and 8.42 g/t Pd. The deposit is hosted by gneiss, migmatite, gabbro and pseudotachylite (Sudbury Breccia) 100 m below the base of the SIC.

Jan 1, 1996

By Rozycki J

The results of shaft lining monitoring gave rise to an investigation of cracks observed in the structure. An hypothesis was made that the cracks might be due to stresses caused by energy wave propagation, triggered during blasting or by the rock falls. However, it could not be excluded that the cracks had their origin in the rheologic changes taking place in the concrete. To prove the hypothesis, an investigation of the scale of the increase of stress due to the energy triggered was undertaken. At the same time it was decided to attempt to determine the "damage threshold" for such material in the danger zone. In the paper the investigation and its results are presented, as conducted in one of the shafts. In conclusion, certain generaliza- tions are proposed to give a starting point in the consideration of similar problems elsewhere.

Jan 1, 1987

Increasing attention is being focussed worldwide on the strategic environmental assessment of mining projects, including consideration of cumulative environmental effects. In New Zealand there is now an end in sight for inappropriate delays in resource consent approval of responsible mining projects. This paper investigates six case examples of recently consented mining and quarrying projects, whose applications were notified. It also explores the nature of delays that occurred, the factors that contributed to the delays, and whether the consent process delivered fair and effective public participation and desirable environmental outcomes.

Jan 1, 2005

By Browner R, Kyle J

The adsorption of gold cyanide by the weak base ion exchange resins, PAZ-4¦ and Duolite A-7C, the neutral polymeric adsorbent, Amberlite XAD7¦, and the strong base resins, PAZ-8~a and IRA-400 have been studied in both low and high salinity waters, and their performance compared with activated carbon. A systematic study has also been made of the effect of different ions (Na+, Cat+, Mgt+, Cl', SO4) ) on the gold adsorption capacity and kinetics of these resins. The results indicate that, contrary to popular belief, the ion exchange resin, can perform effectively in highly saline environments. The performance of the neutral polymeric adsorbent im- proves with increasing salinity but cannot match the performance of the ion-exchange resins.

Jan 1, 1991

By McLeod RL

The Mt. Morgan mine, located 36 km SSW of Rockhampton, Qld at Lat. 23¦38' S, Long. 1500 22'E, is hosted by a Middle Devonian sequence of acid volcanic rocks and sediments. The Upper Nine Mile Creek (UNMC) prospect, 14 km SE of the Mt. Morgan mine, is in an ap- parently equivalent sequence of rocks. The Late Devonian Mt. Morgan Tonalite separates the two areas. The Mt. Chalmers mine, located 27 km NE of Rockhampton at Lat. 23¦ 18' S, Long. 150039'E, is hosted by the Early Permian Berserker Beds. These three volcanogenic massive sulphide deposits show pronounced similarities in their host rock lithologies and stratigraphic-struc- tural settings.

Jan 1, 1987

Within the Business Process Improvement Program initiated at Placer Dome during 2003 was the Business Performance Management Project (BPM).BPMÆ s aim has been to extract productivity improvements from individual business units by providing a model for implementing leading practice based management process within the Placer Dome Group, sharing management best practice, injecting new management techniques and instilling a continuous improvement culture. The installation of an underground dispatch system has been a key component of the BPM project at Osborne Mine.Information capture and analysis allows for corrective action to be planned and executed before there is a material impact on the performance of a business unit. This paper briefly describes the principles and practices of effective business performance management, the four processes of a management operating system namely; strategic and tactical planning, implementation and reporting. The identification of business drivers, their measures and associated key performance indicators is discussed. The benefits of an underground dispatch system at Osborne with respect to safety, production and maintenance is described along with the installation process within the mining department that included its configuration, resourcing and roll out.

Jan 1, 2005

New technology is a significant factor in the present upsurge in world, and Australian, gold extraction and production. The main technologies in current use for gold production are described, referring to overseas developments. Areas where existing techniques have shortcomings or new methods are needed are pinpointed and discussed. Much research work on gold metallurgy is under way round the world, and many new developments have potential. Many of the current research activities round the world are covering unusual and striking areas, with surprising results starting to come through. Some of the "blue sky" techniques reportedly under investigation are identified, together with consideration of when changes in technology are of value. The consequences of new technology for personnel involved in gold plant operations will be raised, including the new education now required.

Jan 1, 1986

By Warren R. P

When the original Mount Gunson joint venture, between CSR and United Uranium ceased operations in December 1971, an intensive ex- ploration campaign was launched to prospect for more ore in the Mount Gunson region. This campaign resulted in the discovery of the Cattle Grid deposit. A comprehensive sampling programme proved the existence of 4.6 million tonnes of ore, at a mean grade of 2.4% Cu, calculated at a 1.0% Cu cut-off. The planning and development programme that followed this discovery included not only the mining and metallurgical aspects of the exploration of the deposit, but also the en- vironmental aspects. Preliminary work included data collection with respect to meteorology, soil types, and existing flora and fauna.

Jan 1, 1976

The Australian Mineral Industry's growth in the last two decades is directly related to the skill and experience of its consultants in mining, metallurgy, geology, finance, management, marketing, and engineering. The role of mining consultants needs to be re-examined, so that the quality of the service they deliver will continue to be adequate for the 1990's. One means of this evaluation is by examining Case Studies in the strategies and difficulties of developing contract and entrepreneurial research.

Jan 1, 1986