Search Documents

The optimisation and validation of shearer cutting methods is a time consuming engineering task. Many different parameters, of which not all can be controlled, can vary. The easiest solution, to increase the installed power and the longwall length, is not always the best. A different cutting method can increase the capacity without the need of new machines. The Department for Mining and Metallurgy Machinery at RWTH Aachen University therefore developed ProSL, the simulation tool for shearer and longwall operations. ProSL enables the engineer to create his own cutting methods and compare it with other methods. Machine-data can easily be varied to see the impact on the method. The research shows that sophisticated longwall methods increase the productivity of the system. The paper presents the results of the calculation with ProSL and shows how higher efficiency and lower costs can be achieved.

Dec 6, 2010

By Marshall GA, Dickerson AW

The efficient operation of large haul trucks in large open pit mines requires an economic trade off between the haul route quality, the haul truck payloads and the level of haul truck reliability. This paper describes an investigation into the relation- ship between haul route surface quality and the level of structural reliability of a haul truck main frame. An instrumentation system for unattended recording of data on a haul truck operating normally in a mine and com- puter based analytical procedures were developed and used to identify which road segments contribute significantly to fatigue cracking at various sections of a haul truck main frame. INTRODUCTION In many open pit mines there is exten- sive use of large haul trucks to move over- burden and minerals. In most open pit hard rock mines, both the overburden and mineral ore are moved by large rear dump type haul trucks. Similar haul trucks are also widely used for coal overburden and mine site coal haulage operations in New South Wales, South Australia and Western Australia. Large bottom

Jan 1, 1982

By J C. de Vries

When times are tough in the mineral industry û as they have been for some time û typical responses by mining companies are to cut costs and/ or increase production. The latter is seen to spread fixed costs, thereby also reducing unit costs per tonne mined. However, most mineral deposits respond to increased production rates by lowering ore grades, so the reduction in cost per tonne of ore does not necessarily result in a reduced cost per unit of metal produced. The authorsÆ experience is that this process often leads to a mine plan that is a long way from optimal. Producing to the point where marginal cost equals marginal revenue may work well in a manufacturing operation, but it is not necessarily the best strategy for a mining company with a depleting resource. Variations in tonnage and grade with depth, ore reserve optimism and a variety of other factors conspire to produce variations in production rates and grade that often result in suboptimal outcomes and potential mine failure. Added to this is the focus of industry analysts and senior corporate management on such measures as unit costs and ounces in reserves. This is perceived to have the perverse effect of driving the share price down when strategies are adopted that actually improve the value of the mining operation, and vice versa! Many mine failures can be prevented by a close examination of the tonnage grade curve and an understanding of how margins, net cash flows and resulting business risk change with cut-off grades and rates of production. A few relatively simple analyses early in the evaluation of a project can demonstrate the tradeoffs between the main decision parameters, leading to right-sizing of the operation. Once major commitments to major capital items have been made, and reserves have been publicly reported, optimisation of the operation becomes much more difficult than if it had been done earlier. Such investigations can also identify the upside potential and downside risks associated with factors outside the companyÆs control. Many strategies that may enhance value in the good times significantly increase the downside risk in the bad times. What is often called risk analysis typically looks at superficial issues, and does not evaluate the major factors leading to the potential for financial disaster. This paper illustrates some of these major risks, and demonstrates how they may be fully evaluated so that corporate decision makers can make fully informed decisions that take account of the real risks.

Jan 1, 2003

By R Young

Independent Project Analysis (IPA) is in the business of benchmarking the performance of capital projects on behalf of owner companies in the processing and extractive industries. IPA assesses between 500 and 800 projects each year. The projects are conducted globally and range in size from about $1 million to over $30 billion. Using the data, we are able to benchmark the performance of Australian projects against the rest of the world. This presentation focuses on the performance of large (greater than $100 million) projects that involve chemical or thermal processing.We regularly hear calls for more processing to be conducted in Australia but on the other hand industry leaders are concerned about the poor success rate of solids processing projects in Australia. Data gathered by IPA indicates that there is good reason for the concern. Out of a sample of 31 large processing projects conducted in Australia, 23, or 74 percent, were classed as failures. This performance is significantly worse than for similar projects in other parts of the world. The presentation analyses why the performance is worse and demonstrates that many of the reasons behind the failures were manageable by the project team. Furthermore, members of the project teams on at least half the failed projects knew that the projects were on a path to failure before the project was authorised but could not be heard.The presentation discusses how large projects that involve process design and, in many cases, new technology, need to be set up for success. *This is an abstract only. No paper was prepared for this abstract.*

Aug 8, 2011

A major problem in the continuous casting of aluminium killed strip steel is the incidence of black and grey lines in the strip surface caused by the alumina inclusions. One place for limiting the number of alumina inclusions is by providing favourable fluid flow conditions in the ladle so that the inclusions float out to the surface or adhere to the ladle wall. In laboratory equipment 20 kg of steel was melted in an alumina crucible of 14 cm diameter in an induction furnace. Deoxidation was carried out while the melt was constantly stirred by argon bubbling. Bubble frequencies were measured at the lance tip using a microphone technique. High speed cine photo- graphy was incorporated to measure melt top surface velocities. Experimental results indicate that the rate of removal of inclusions is a function of both the gas input and the power input. However due to unfavourable surface area to volume ratio, reoxidation of the melt took place. Some other experimental difficulties in working at high temperatures are also discussed such as lance design, melting arrangement and sampling techniques.

Jan 1, 1984

By C Linklater, A Garvie, D Kentwell

Various Australian and international regulatory bodies (Environmental Protection Authority, 2015) require an early assessment of the geochemistry of waste rock. This usually includes estimates of the locations and volumes of potentially acid forming (PAF) materials and requires sampling of the waste rock zones as well as submitting the samples for a series of tests. We know that the required number of samples will vary depending on rock type, mean sulfur levels and spatial variability of sulfur as well as total volume. The key question is how do we know when we have enough samples?This extended abstract describes the application of geostatistical methods to examine how sample numbers and sample locations influence the preliminary conclusions that may be drawn for early stage waste characterisation.CITATION:Kentwell, D, Garvie, A and Linklater, C, 2016. Geostatistics and sample numbers from an acid and metalliferous drainage perspective, in Proceedings Life-of-Mine 2016 Conference , pp 12–15 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

The effects of changes in sintering bed height, coke fuel, suction and basicity on sinter productivity, physical strength and mineralogy were determined. It was found that, for a given iron ore, there is a narrow -coke range which maximises sinter strength, irrespective of bed height (in the range 300 to 500 mm) or basicity (in the range 1.2 to 2.2). Increases in bed height, at a constant coke level, improved the physical strength of the sinter. Productivity increases were obtained by increasing the sintering suction but, at coke levels other than the optimum, these *ere somewhat offset by the decrease in sinter physical strength. At basicities higher than 1.2 (i.e. 1.6, 1.8 and 2.2) there was a narrowing of'the size range of product sinter, with a decrease in the percentage of top size material, and a decrease in the amount of fines produced. Changes in coke, bed height and basicity exert major effects on sinter mineralogy, while the Nagoya index was mainly influenced by cote and bed height Changes.

Jan 1, 1975

This paper examines the interplay between longwall support design/geometry features, operational controls and geological features on ground response. Experience from several investigations is used to demonstrate the influence of factors such as longwall support capacity and geometry, setting pressure, coal seam strength and stiffness, tip-to-face distance and hydraulic supply and control system parameters on longwall ground response. These factors are then used to outline the requirements on key controls such as retreat rate and cutting height and their influence on allowable roof convergence. The ground response curve concept as a means to provide graphical representation of longwall support and strata interaction processes is presented. The approach was developed to address the requirement for a practical longwall support evaluation and selection tool that can take account of support load influences such as changes in roof geology or cover depth. An example of the comparison between single pass longwall and top coal caving in a thick seam environment is given to demonstrate the influence of the various factors discussed.

Jan 1, 2005

By Chang TS, Suzuki K, Go H, Nakamura S, Kuwano Y

In 1979, a test operation of an experimental blast furnace was carried out to investigate the behavior of a sort of formed coke, which was used safely by 30% of total coke charge in No.2 B.F., Sakai works, NSC, in 1975". The Mashec-type formed coke of 60 x 60 x 40 mm in dimension was crushed and screened so that it had the same size range (1011,20 mm) as ordinary coke used in the base operation. Preceding to the operation, some experiments on the properties of the formed coke and the effects of crushing on them were performed.

Jan 1, 1981

By B Belle

"Mines around the world are inherently and operationally diverse. Current methodologies for the design of mine ventilation and cooling infrastructure involve controlling major safety and health hazards. Globally, it can be estimated that mine ventilation systems from various commoditiescirculate over 150 000 m3/s of exhaust air through shafts. Additionally, over 2 000 000 workersare transported every day through shafts in labour-intensive mining countries like China, India,Southern Africa, and the Americas. A key objective of this paper is to share experiences and provide a case for the revision of ætime-honouredÆ ventilation design parameters based on a benchmarking exercise on design exhaust shaft velocity from various global operations (gold, diamond, platinum, coal and base metals). An active fi eld observation on exhaust shaft velocity has indicated that, regardless of the commodity or continent where the mine operates, almost all life-of-mine (LOM) design parameters provided are in the same range of 20 m/s to 22 m/s, which is not convincing considering signifi cant variations exist in shaft depths, geography, commodity, operating and capital costs. From a due diligence perspective, there are no documented views that are available on the most widely used design exhaust air velocity. Based on the global exhaust shaft velocity data, it is noted that a significant portion of shaft velocities are outside the current design velocity of 20 m/s (some operating up to 30 m/s) and other signifi cant portions of the exhaust shafts operate in the critical velocity range. In the case of Australian coal mines, limited data suggests that none of the mines have ever reached the LOM design exhaust shaft velocity. It is self-evident that when the shafts are not operating at their design quantities either the mine system resistance is low or the ventilation and main fan is operating ineffi ciently. The most common reasons given for not reviewing the shaft system were, ætime-honouredÆ design parameter are being used and cannot be changed, mine fan pressure limits, possible fan blade damage, possible spontaneous combustion risks, leakage or simply did not consider such a possibility. In conclusion, the study has reiterated the historic lessons that a safe and expensive airway should not be utilised uneconomically by circulating too litt le air through it."

Jun 1, 2012

The role of the mine geologist in a business perspective is self-evident to some, but to others it may be a new concept. All mine geologists need to know exactly how they add value to the business if they are to be successful. Alternatively, if they do not add value, then they will become redundant. This paper seeks to understand some of the contributing problems that hinder the mine geologist from operating in a business perspective. In doing so, a new context (for some) is proposed to aid the mine geologist and the operation gain greater value from geology. The proposal suggests how to ensure that the activities of our geologists are intrinsically linked to the business process that we are involved in. The mine geologist can and must play a pivotal role in the success of an operation. To do this, they must understand some principles of business such as:process, customer/supplier relationships, and organisational structure. Our geologists must know the business objectives, understand the product that the customer needs and use their geological skills to deliver the product safely, on time and to specification. As geologists, we can be instrumental in ensuring that the operational environment is structured in such a way that maximum value is realised, not only from the mine geologists but the entire site team. In doing so, mine geologists will realise their full potential in delivering the outcomes the business demand, and therefore be recognised as strong contributors to business success.

Jan 1, 2000

This paper discusses the requirements for a successful simulation modelling study, and the steps involved in the modelling process. Advantages and disadvantages of simulation are described, and a case study highlights how not to go about it. Two other case studies, for a decline truck haulage and a block caving production operation, are used to illustrate the types of variables whose impact may be investigated. Typical results are presented to indicate the sorts of presentation styles the author has found useful for conveying study results to project sponsors. Standard spreadsheet charting techniques can be very useful in this respect, but the possibilities are limited only by the imagination of the study team.

Jan 1, 2000

By P Dowd, A Adeli, C Xu, X Emery

Geometallurgical modelling is increasingly being incorporated into mineral resource modelling and estimation as a means of increasing efficiency, decreasing operating costs and reducing risk in mining operations. Traditional geostatistical workflows for geometallurgical modelling face several difficulties, in particular, related to the non-additivity of process response variables, to highly heterotopic data sets and/or to preferential sampling designs, all of which may explain why most attempts to estimate geometallurgical response variables from assay data and mineralogy are still based on statistics and machine learning. The aim of the work presented here is to demonstrate the applicability of geostatistics to estimate copper recovery from copper sulfide ores at the Prominent Hill Iron Oxide Copper-Gold (IOCG) deposit in Australia. As recovery is non-additive, the preferred workflow is the joint estimation of the masses of metal in the feed and in the concentrate, both of which are additive variables. While the mass of metal in the feed can be estimated from abundant online assay analyses, the mass of metal in the concentrate can only be estimated from a very limited number of laboratory-scale batch flotation tests. Traditional approaches to estimating the masses of metal in the feed and in the concentrate, such as simple and ordinary co-kriging, are described and discussed. A modified version of co-kriging is introduced, which incorporates linear relationships between the mean values of the input variables, in addition to a spatial correlation model. Co-kriging with related means is shown to outperform traditional simple and ordinary co-kriging in terms of precision, accuracy and consistency of the estimates, and offers a practical and efficient tool to deal with highly heterotopic and preferential sampling designs.

May 24, 2023

By Y Potvin

Underground mines in Australia are progressively operating at greater depth, sometimes in conditions where mine induced stresses are very high. In such conditions, the seismic activity often becomes intense and violent and in response, mines must develop and implement a sound rock burst risk management strategy to continue operating safely.This paper discusses the latest techniques successfully used in Australian mines to mitigate the risk of rock bursts. In particular, the paper describes how the analysis of data collected from seismic monitoring systems can provide an understanding of the seismicity and be used for quantifying seismic hazards in the mine. Once an adequate understanding and assessment of seismic hazard has been achieved, the associated risk can be mitigated using different layers of protection.Strategically, modifying the mining method, the extraction sequence and/or the mining layout can alleviate the seismic hazard, but these solutions generally cannot be implemented rapidly. In the short-term, seismic risk can be mitigated tactically using an energy absorbing support system or to remove personnel from being exposed to rock burst damage by implementing exclusion zones.

Mar 21, 2011

By M Berry

Many mining companies routinely use benchmarking to review their operational activities and associated costs. The aim is to measure operational performance against industry norms, and identify areas where a company is performing better or worse than industry best practice. The goal is continuous improvement.In general, mine technical services, including mining geology activities, are not routinely benchmarked. There are exceptions, such as the cost of drilling per metre and the average discovery cost per unit of metal, but generally mining geology activities are only included indirectly in mining benchmarking studies.Aspects of benchmarking can play a critical role in assisting mining geologists to improve the efficiency and effectiveness of the services they provide. Industry norms for many generic mining geology functions have not been developed and measured, and therefore it is impossible to use external benchmarking to assess performance against other mines. But when used in parallel with quantifying the value of mining geology functions and establishing strategic goals for the team, key components of benchmarking methodology can provide essential feedback on how a team is performing against these strategic goals.CITATION:Berry, M, 2014. Benchmarking – does it have a role in improving the performance of mining geology?, in Proceedings Ninth International Mining Geology Conference 2014 , pp 361–366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By V S. Vutukuri, K Shariar

This paper present a modification of selected strength criteria for coal and rocks containing weakness planes. The three strength criteria, namely, Murrell (1965), Bieniawski (1974a, 1983) and Hoek and Brown (1980) have been assessed for coal (containing weakness planes) by using triaxial strength tests. Triaxial test results indicated that the strength of coal specimens depends on the weakness plane inclination with respect to the principal stress direction. However it is shown that with increasing confining pressure, the effect of weakness planes inclination on the strength of coal specimens is reduced. The constant parameters in the three failure criteria for coal are determined for each weakness plane inclination by using the Datafit computer program (nonlinear regression analysis) and the results are compared with other rock types.

Jan 1, 1999

By G Noonan, S Thomas, M Limbert

Stuck drill rods (often referred to as bogged rods) in production ‘upholes’ are a common problem in the underground mining industry. Bogged and broken off drill rods have the potential to fall out of the hole without warning, posing a serious hazard to personnel and equipment below.Current industry practice to alleviate this hazard can be to either grout the hole in order to lock the drill rods in place, or to ‘plate over’ the hole with a rock bolt. Each of these operations seriously delays mine production as both require demobilisation of the production drill and mobilisation of alternative personnel and equipment to address the hazard. Both methods have been assessed for safety and efficiency and were found to be expensive, time consuming and in the case of plating over, ineffective.To address the safety and efficiency short-comings of the traditional practices, the long hole plug (LHP) has been developed to safely secure the lost rods in the hole. The LHP when struck by falling drill rods behaves similar to an expansion shell anchor transferring the axial forces from the falling drill rods horizontally into the rock mass. It is installed using standard production drills allowing work to safely continue with little interruption.Extensive testing has been carried out on the LHP in the laboratory and underground at the Rosebery mine on the west coast of Tasmania, Australia. Testing has included static pull testing, full scale drop testing and underground trials.The outcome of this work has proven the LHPs ability to add safety, volume and cost benefits to the Rosebery underground operation and it is currently in use at that site. It enables proven elimination of a common workplace hazard immediately, thus eliminating delay on the mine’s production cycle.CITATION:Thomas, S, Noonan, G and Limbert, M, 2017. Long hole plug – addressing the hazard of bogged rods in ‘upholes’, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By R Berry, J Lett, C L. Harraden

"In the past decade, increased processing capacity combined with precision robotics in high resolution spectrometers has resulted in a new generation of high-speed hyperspectral core logging systems. The application of these multisensor automated platforms provides a key advancement in the characterisation of metal resources. The development of this technology has allowed for comprehensive, drill core-based, mine-scale rock mass characterisation studies. Here we propose a new method for the extraction of parameters that seek to more accurately quantify ground conditions, including quantified rock mass rating (RMR) and the Rock Tunnelling Quality (Q) Index. Data inputs include rock quality designation (RQD), number of joint sets, joint roughness, joint alteration and joint spacing. Geologists and geotechnical engineers have historically collected these inputs by manually logging drill core. With automated core scanning technologies, these parameters can be estimated from the acquired image data and used to objectively calculate RMR and Q-index values for oriented core.Corescan is an automated hyperspectral core scanner that uses a 3D laser profiling system to measure the height of the surface of drill core. This technology allows for rapid core analysis to produce detailed fracture and rock condition data. Through an integrated geometallurgical approach, the proposed methodology will test the accuracy of joint measurement using the height profile Corescan data from oriented drill core. This will be combined with joint roughness and alteration mineralogy measured from the hyperspectral images to calculate the RMR and the Q-index continuously downhole. The values obtained can then be compared to the traditional, manual geotechnical log data. If the precision is sufficient, these techniques can then be applied site-wide to automate the collection and modelling of key ground condition classification indices across an entire deposit. Compared to the laborious manual geotechnical logging procedures that currently form the industry standard, utilisation of core laser profile data and high resolution red-green-blue (RGB) images provide an opportunity to collect large volumes of consistent geotechnical data, which can increase the efficiency and accuracy of deposit scale geotechnical models.CITATION:Harraden, C L, Berry, R and Lett, J, 2016. Proposed Methodology for Utilising Automated Core Logging Technology to Extract Geotechnical Index Parameters, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 119–124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By J Hadjigeorgiou, T R. Stacey

A ground support system is a combination of individual reinforcement and surface support elements that work together to retain and contain the rock mass. The various elements are subjected to external loads and to interactive loading between individual ground support system components. This paper focuses on the challenges in determining the capacity and behaviour of mesh, recognizing that installed mesh can be subjected to several loading mechanisms. Field observations from underground hard rock mines demonstrate that there are multiple types of damage and modes of failure of mesh. However, these are difficult to reproduce in a laboratory environment. A critical review has shown that existing mesh laboratory testing rigs reproduce very limited loading conditions that may not be representative of underground conditions. This has significant implications in quantifying and extrapolating the performance of mesh to ground conditions. CITATION:Hadjigeorgiou, J and Stacey, T R, 2018. Challenges in determining the capacity of mesh, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 280–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Saghaeian, A H. Baladastian, A Dehghani Ahmadabadi, V Sheikhzadeh, R Hejazi

This research was done to reduce silica from mixed hematite concentrate of Barfkar Iron Ore Sample and increase Fe grade using reverse flotation method (Depressing Hematite and floating Silica). The used sample in the reverse flotation tests was a mixture containing two types of hematite concentrates (Spiral cleaner concentrate and Slon-VPHGMS cleaner concentrate) with the percentage of 16 per cent and 84 per cent, respectively. Fe grade of two samples was 59.31 per cent and 57.52 per cent and SiO2 grade was 5.83 per cent and 6.71 per cent, respectively. After mixing, the Fe and SiO2 grade of the mixed sample was measured at 58.10 per cent and 6.20 per cent. For flotation tests, effect of variable operational parameters including feed size distribution (d80 = 130 microns and d80 = 53 microns), pulp solidity (25 per cent and 30 per cent w/w), pH (9.70, 10.20 and 11), Sodium silicate as a dispersant (500, 1000 and 2000 g/ton), Starch as a depressant (500, 1000, 2000 and 3000 g/ton) and EDA as a collector (180, 300, 400 and 500 g/ton) were investigated. For evaluating the influence of Sodium silicate and Starch dosage, initial flotation tests were performed on the main sample (d80 = 130 microns). These two parameters had no significant effects on the yield, Fe, and SiO2 grade of flotation concentrate based on test results. In the next step, screen analysis was carried out on the main sample for mineralogical studies. Accordingly, the suitable size distribution for releasing Fe and SiO2 particles was smaller than 53 microns. Therefore, the sample was crushed until d80 = 53 microns. Then, supplementary tests were performed on the crushed sample for studying the pH range, pulp solidity, and EDA collector dosage. After doing silica removal flotation tests based on the designed pattern and comparison of the results, the conditions consisting of size distribution d80 = 53 microns, pulp solidity 25 per cent, pH 10.20, Sodium silicate 1000 g/ton, Starch 1000 g/ton, and EDA 500 g/ton was selected as optimum values. In the last test, Fe and SiO2 grade was measured at 60.00 per cent and 3.93 per cent, respectively, and Fe recovery was obtained at 74.93 per cent.

Aug 24, 2022