Search Documents

By Sarracino R. S

A number of ideal detonation codes are used internationally for estimating the strength of explosives compositions. Important and far reaching decisions by explosives users are ofen based on the predictions of these codes, but since different codes can deliver very different answers for the same composition, there is a strong possibility of decision makers being misled. In order to both provide a sensible basis for comparing the theoretical energy from explosives from different manufacturers and to prevent the entire rating system from slipping into disrepute, it is in the interests of all to reach agreement on fundamental criteria used by detonation codes for detemtining strength. The problem is illustrated by a case history and basic conventions are proposed, specifically the adoption of energy of reaction as a fundamental and code independent indicator of explosive energy, and agreement on disclosure by suppliers of key non-proprietary information. These measures would assist explosives customers in assessing the true strengths of explosives from the strengths calculated by the different ideal Codes.

Jan 1, 1990

This paper is written as a supplement to that of Edwards, Baker and Knight on "The Geology of the Wonthaggi Coalfield" 1, the West Area pit being in an early developmental stage at the time of their paper. The thin seams to the west of Dudley Basin 2 had beenknown for many years but it was not until 1935 that it became necessary to work them. The West Area Pit came into production as Dudley Area Pit approached exhaustion in 1937. From available information it was estimated that early work would be in a 36in. bottom seam. The present top seam was not included in the reserves, but it was to be extracted where it proved thick enough for economical working.THE SEAMSEdwards, Baker and :Knight (1944) had insufficient information to correlate positively the West Area seams with those in the Dudley Basin. Their opinion was, however, that they were a westerly extension of the Bottom Seam. Since then the driving of the present north-east heading towards No. 4 Bench McBride Tunnel has established that the West Area seams are those worked as Bottom Seam in the Dudley Basin. West Area Top Seam is a seam that occurred above the Bottom Seam in the Dudley Basin. Only sporadic attempts have been made to work it in Central Area, because 30in. was considered an economic minimum height until recent times. This seam should not be confused with Top Seam, Dudley Basin, which lies some 300ft. above the bottom seam measures and except in isolated areas over deeper workings has been eroded away in West Area.

Jan 1, 1953

Block caving is the lowest cost underground mining method but it has relatively high risks and a high up-front capital and development cost. It has application to large, often lower-grade orebodies where high production rates can provide good returns on the investment. However, it has a range of technical risks that are peculiar to block caving and the usual financial, political and environmental risks that may be exacerbated by the long lead-in times associated with the development of a block cave operation. With initial development costs that may be $100 M to $1000 M when the building of a treatment plant is also required, it is obviously important to minimise and manage the risks. In a greenfield project, commitment to a substantial proportion of the capital expenditure may be required to gain access to the deposit, and the decision to proceed at this stage would be based very largely on interpretations of drill hole data. In established mines the data may be supplemented by geological mapping and past experience, etc. The quality of this data is critical and yet it is frequently degraded through poor techniques and avoidable omissions. The final decision to proceed would be assessed on projected commodity prices, mining capital and operating costs, dilution and run of mine ore grades. The latter will vary over the life of the project and these can be estimated with drawdown or draw control modelling techniques. In this modelling, there are further risks in the assumed modelling parameters or that the modelling technique may not be applicable or appropriate. The paper addresses the most critical technical and operational risk areas and provides some practical precautions that can be taken to reduce these and improve the reliability of the geological and geotechnical models.

Jan 1, 2000

Geostatistical analysis, resource estimation and three-dimensional modelling of the gold grade distribution was undertaken using exploration drillhole data taken from the Mt Leyshon gold mine. The main aims of the project were to provide an independent estimate of the primary gold resource and to improve the estimate by better understanding the statistical distribution of gold and the establishment of more robust variograms. These criteria have been achieved by the removal of low grade sub-populations, increased sample size and access to data from the most recent drilling program. The outcome of this statistical study has led to a lowering of the sill and nugget variance of the variograms used. Distinct geometric anisotropy was identified in all the resource estimation zones and was used to model gold grade distribution.Two independent resource estimates were established from the primary gold resource, one based on a geostatistical estimator (kriging) and the other on a traditional estimator (inverse distance weighting). Both methods were compared with a contemporary kriged estimate by Mt Leyshon Gold Mines Ltd.

Jan 1, 1993

By M Gao, V Lawson, W Valery

Changes in metal prices and mine output over recent years have required the Copper Concentrator of Mount Isa Mines to operate at annual tonnage rates varying from 4.0 million to 6.5 million tonnes. Several circuit combinations were operated during this period utilising up to two semi-autogenous grinding (SAG) mills and up to two ball mills. The aim was to maximise grinding efficiency and keep unit costs constant regardless of throughput rate. Measures to improve the SAG-ball mill unit operation were implemented with each circuit change. These included installation of a splitter to divert SAG Mill cyclone underflow back to the mill, increase SAG ball charge from four per cent v/v to eight per cent v/v, reduce in SAG top feed size and increase of ball mill grinding medium size. Modelling work and surveys led to a new design of the SAG liner profile from 60 rows of rail bar liners in a high-low arrangement to 40 rows of top hat liners in a high-high arrangement. An on-line SAG Mill feed sizing monitor was recently installed to improve grinding control.

Jan 1, 2000

By R Moreby, J Kok, L van den Berg

The high production rates achieved from mass mining methods such as block caving, sublevel caving and longwall mining require large conveyor belts, trucking loops (diesel/electrical) and rail systems for ore handling. However, the ore handling systems used in mass mines introduce a significant amount of heat into the overall ventilation system, which may be problematic at depth or in mines located in hot climates.In particular, the heat load from a conveyor system is not always well understood and consists of various components, including frictional heat from idlers, heat from electrical motors, heat from the drive train and heat from broken rock transported on the conveyor system. This paper presents results from a study that investigated the heat introduced to the ventilation air from a large conveyor system. The conveyor system transports ore with a maximum virgin rock temperature of 41°C from a depth of over 1 km. Air, belt and rock temperatures were measured in the conveyor system to evaluate the distribution of heat loads.CITATION:van den Berg, L, Moreby, R and Kok, J, 2015. Heat load estimation from conveyor systems in mass mines, in Proceedings The Australian Mine Ventilation Conference, pp 63–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By S Khadhraoui, T Yusuf, C Kirmse, E Hecker, R Degel, A Akouch, N Borowski, M Reuter

For an optimal design and control of metallurgical processes, a deep understanding of the thermodynamics of the governing reactions is required. Modelling the thermochemical behaviour of those reactions is complex, as it involves multi-component and multi-phase systems. For this purpose, thermodynamic computing systems such as FactSage™ (Bale et al, 2016), which combine Gibbs energy minimisation routines with large databases of optimised thermodynamic data of solutions and compounds, have been used within the SMS group GmbH. Recently, the successful integration of those thermodynamic computing systems into the digital platforms of SMS has been achieved through ChemApp, which made running complex thermochemical calculations in Python-integrated development environments possible. ChemApp is a programmer’s package for thermochemistry and incorporates the Gibbs energy minimiser of FactSage™ as reported by Petersen and Hack (2007) as well as by Zietsman and Petersen (2018). The digital platforms link the fundamental and the industrial aspects together and can be applied as a process advisor, or for the evaluation of the environmental footprint and the economic implications of different process routes, as discussed by Reuter (2023). Two examples illustrating the progress of the developments in this regard will be introduced: 1. The Tilting Refining Furnace (TRF) for copper scrap recycling and refining to anode copper (the BlueControlApp). 2. Dephosphorisation control for the oxygen steelmaking process (Basic Oxygen Furnace (BOF)).

Jun 19, 2024

By Fair A, Oxenford J

Syncrude Canada Ltd operates one of the largest open pit mines in the world at Fort McMurray in northern Alberta, Canada. In 1993, Syncrude mined and processed 131.2 Mt of oil sands to produce 67.0 MBbls of synthetic crude oil (SCO). This represents approximately 13 per cent of Canada's crude oil requirements. In addition to the oil sand mined, Syncrude moved approximately 96 Mt of overburden ahead of the mining operation in 1993. Since start-up in 1978, Syncrude has had outstanding success in improving the safety and reliability of its operation. Much of this success has been achieved by reducing risk through the application of new and improved technology. This improved safety and reliability has resulted in, among other things, very significant improvements in operating costs and profitability. This paper discusses some of the technology applications that have been introduced at Syncrude to reduce risks to people, equipment, operations and the environment. Three specific examples will be discussed in detail to demonstrate how reductions in risk have greatly improved the operation.

Jan 1, 1994

By G M. Taylor

The application of high technology to monitor and control fire life safety, critical functionality in tunnels and underground spaces generally has progressed at an ever accelerating rate over the past decade. Today these systems comprise some of the most complex and little understood aspects of the tunnel/underground facility construction industry, with this area being perceived as high risk comprising impenetrably complex ‘black box’ technology covered in blinking LEDs. This paper will seek to explode some urban myths and common misconceptions associated with such systems, providing its intended audience with a review of what all this technology comprises and where the real risks lie in its delivery lie.The author contends (and looks to support such contention via this paper) that by applying baseline project and risk management processes to the procurement of this widely misunderstood black box technology, the quality of the final outcome can be much improved, driving innovation, reducing both cost and significantly mitigating delivery risk.CITATION:Taylor, G M, 2014. Procuring control and intelligent traffic systems for major new build projects – avoiding pitfalls and maximising value, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Legislation up to the early 1950s prevented the mechanical extraction of pillars. The mines operating at that time had formed extensive areas of pillars. When permission for the mechanical extraction was gazetted, conventional equipment was employed for pillar extraction and generally using hand mining systems. The mid-fifty's saw the of continuous miners. These machines eliminated the disadvantages of conventional equipment and the necessity for multiple working places. Some new layouts for panels emerged; however, actual extraction methods of pillars still followed closely that of hand mining. During the early sixty's the extraction of standing or new formed pillars was undertaken by the "open-end lift" or a "split and lift" method.

Jan 1, 1974

By A Nigam, K Biswas, R Sarkar

Because of the problems with 1st and 2nd generations of Advanced High-Strength Steels (AHSS), a 3rd generation of AHSS steels has become prominent and these steels have properties in between the 1st and 2nd generations of AHSS. However, although the 3rd generation of AHSS is a promising candidate as a replacement for its predecessors, there remain some challenges in processing these steels which are essentially medium Mn (Mn content ~ 5–7 wt per cent) and high Al (Al content ~ 1– 3 wt per cent) steels. The use of conventional casting powders based on the CaO-SiO2 system is unsuitable for high and medium Mn/Al steels. This work investigates the development of CaO-Al2O3- based mold fluxes for casting third-generation AHSS steel. Mold fluxes, with otherwise similar compositions but different C/A ratios, are tested and their crystallisation behaviour is examined using differential scanning calorimetry (DSC). A calcium aluminate phase having a composition Ca12Al14O33 was found to be the main crystalline phase in the mold fluxes. A decrease in crystallisation temperature was observed as the CaO/Al2O3 ratio increased from 1.00 to 1.33. The effective crystallisation rate constant exhibited an increase with decreasing crystallisation temperature, indicating a potential influence of nucleation rate on the overall crystallisation rate and suggesting an anti-Arrhenius behaviour in the crystallisation process of these mold fluxes.

Aug 21, 2024

Hydraulic backfill is generally retained in stopes using permeable barricades. Mitchell et al (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et al (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading conditions. This paper discusses the circumstances that led to these incidents and analyses the modes of failure. The standards for the safe operating of hydraulic backfill systems are reviewed along with requirements for ongoing management and control. The design requirements of barricade construction are analysed and some appropriate guidelines introduced.

Jan 1, 1998

LKAB operates two underground mines in Kiruna and Malmberget, Sweden. Blast furnace pellet is the main product and makes up 70 per cent of total production. The orebodies are hosted by 1910 - 1860 Ma old volcanic rocks. The host rocks and the ores were affected by the Svecokarelian orogeny for 1890 - 1860 Ma ago. The deposit belongs to the Kiruna type apatite-rich iron ore. Magnetite is the main ore mineral but haematite is the dominant ore mineral in some orebodies in the western part of the deposit. Large-scale sublevel caving is the dominant mining method. Three main haulage levels are in operation at present. The ore boundaries and quality can be detected by geophysical logging resulting in reduced waste dilution and subsequent grade reduction. The susceptibility measurements have been used in the magnetite ore since 1991 and gamma-gamma measurements in the haematite ore since 1998. The mining scale has increased during the last 20 years but diamond drilling has remained at approximately 18 000 drilling metres per year. Uncertainties in the ore constructions can lead to unexpected cost increases, ore loss and dilution. The ore boundaries are evaluated with percussion drill holes using in-hole geophysics to achieve satisfactory geological knowledge. The probes are calibrated in all currently mined orebodies. The correlation between core sample assays and measured susceptibility and gamma-gamma values is strong. The cost to determine the ore boundary by percussion drilling with in-hole geophysics is two-thirds lower, and productivity is six times higher compared to diamond drilling. The measurements are made by geotechnicians and the interpretations by a geologist. The results are transferred to a database and presented three dimensionally as holes with iron grade intervals on mine maps. The interpreted holes are used by the geologist in various ways in the geological modelling. Layout planning uses the measurements as a tool to place the drifts at the correct distance from the ore contact especially in the longitudinal sublevel caving and the production hole planning to optimise the final length of the cross-cuts and drifts for best ore recovery.

Jan 1, 2006

By Costello MC

An alternative process for desorbing and recovering metals from activated carbon has been developed, and is the subject of several patent applications by Micron Research (W.A.) The system uses the principle of conditioning the carbon in a strong alkaline cyanide solution followed by distillation desorption in a fractionating column, using the carbon as the column packing and methanol as the desorbing agent. The system offers the following advantages : (a) The processes of desorption, methanol recovery and reactivation are all carried out in a single column with the carbon itself acting as the column packing. No other desorption plant items or fractional distillation equipment are required. (b) The metal values are concentrated into the water content of the carbon and no other water is used except as condenser coolant. This produces very high grade gold silver solutions which give high current efficiencies in the electrowinning step. These high gold concentrations allow almost complete separation of gold and silver from copper in the electrolytic cell. (c) The process is completed to a tailing assay of less than 200g Au/tonne carbon in 15 - 20 hours allowing turn around of carbon batches on a daily Basis.

Jan 1, 1982

By A M. Wala, H W. Wu

A research project incorporating a number of mine site exercises to reduce the effects of fire incidents and possible consequent health and safety hazards has been undertaken focused on the application of mine fire simulation software packages for contaminate tracing and fire modelling in coal and metalliferous mines. This paper examines aspects of introduction of inert gases to underground workings to aid recovery of a mine following a fire. Broad conclusions from work undertaken at individual Australian coal mines are discussed as examples. The effort is built around the introduction of the fire simulation computer program æVentgraphÆ to the Australian mining industry and the consequent modelling of fire scenarios in selected different mine layouts. Case studies have been developed to examine usage of inertisation units and particularly application of the GAG jet engine unit. One example has focused on selection of the best surface portal location for placement of the GAG for most efficient suppression of a fire. A second has examined a situation with significant seam gas being emitted on the face. This has shown that under certain face dip angles stopping the mine surface fan to reduce dilution of GAG exhaust gases will cause reversal of face air and consequent mine explosion as gas laden air is drawn across a fire. A third examines inertisation and dilution issues in mains headings. mains headings present a complex ventilation network with often numerous parallel headings, hundreds of cut-throughs and a variety of ventilation control devices. In such a complex system (with additional interference from a fire), maintaining control of the movement of inert gas is more difficult than elsewhere in the mine. Some illustrations of this issue are given.

Jan 1, 2005

By Waterhouse J. D, Harris B. M

This paper briefly describes the construction in 1979/80 of a 70m deep trial open pit coal mine near Bowmans S.A. and describes more fully the hydrogeological aspects of the exercise. The primary purpose of the Trial Pit was to provide a large sample (700 tonnes) of coal for combustion tests to be carried out in West Germany and the United States of America. Consideration was given to obtaining the sample of coal by drilling and by shaft sinking as alternatives to open pit methods. It was expected that economic mining of the deposit on an operational scale could only be achieved by open cut methods and it was recognised that major uncertainties existed in planning such a mine in the deep unconsolidated multi-aquifer deposit. It was therefore elected to obtain the bulk sample by constructing a trial open pit, which would be closely monitored to provide as much data as possible for future planning of a full scale mine. The dewatering of the Trial Pit was achieved using 26 deep pumping wells, assisted in the later stages by several hundred well points. This was probably the largest dewatering project currently in operation in Australia.

Jan 1, 1981

Through the stress synthesis of many examples of macrostructure in the middle of China, it can be concluded that in the middle of Chinesetectonics there are two compression-torsion-forces, one of which ( from NW to SE ) came from the northwest side of Aerjinshan abyssal and giant fault("F1A", see Fig.7,8,9 ); the other (from S to N ) came from the south side of the north piedmontal fault of Kunlunshan-the south piedmontal fault of Qinlingshan ("F2K-F2Q", see Fig-7,829 ).Owing to the two compression torsion forces a new special type of structure named rotation-apart structure occurred from Chaidamu basin to Hebai, Henan, Anhui plain,from Caledonian movement, Hercynian movement,Yenshan movement to Himalayan movement, step by step In the north of Qilianshan during the late Caledonian movement: during the Hercynian movement it extended into a vast area including the Chaidamu basin and Eerduosi basin; during the Yenshan movement it spread over the whole area of Helanshan,Eerduosi basin and Hebai , Henan, Anhui plain. In the period of Himalayan movement all these structures revived .The rotation-apart structure controlled the distribution of all mineral deposits and also were the mineralizing structures.The relation between these rotation-apart structure and earthquakes is very close.

Jan 1, 1990

By F Saloojee, F K. Crundwell

Refractory ores need to be pretreated prior to cyanide leaching for acceptable gold recovery. Pressure oxidation is one method of rendering the ores more suitable for cyanidation. The focus of this work is optimisation of autoclave configuration for pressure oxidation. An autoclave for the pressure oxidation of a feed containing pyrite and arsenopyrite was modelled, using the population balance framework. The autoclave model takes into account feed particle size, reaction kinetics and retention time. Mass balance calculations were incorporated into Cycad Process« software. This allowed for the investigation of different circuit configurations. The base case model consists of a single autoclave. The feed was then doubled and additional autoclaves were added to provide the same residence time as the base case. Four different configurations for the additional equipment were simulated. These were parallel, series, series with inter-stage thickening and parallel-series circuits. The options are compared in terms of extraction and productivity. The parallel circuit behaves similarly to the base case. The series and series-parallel circuits have higher recoveries and productivities than the base case. The series circuit with inter-stage thickening provides the highest extraction and productivity. This is because the thickening reduces the slurry volume and increases the residence time of the solids in the downstream autoclave.CITATION:Saloojee, F and Crundwell, F K, 2013. Optimisation of circuits for gold pressure oxidation, in Proceedings World Gold 2013 , pp 181-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P F. Hodkiewicz, J de Lacey, M Stewart, R Lane

"Implicit modelling is an approach to spatial modelling in which the distribution of a target variable is described by a unique mathematical function that is derived directly from the underlying data and high-level parametric controls specified by the user. This modelling approach may be applied to discrete variables such as lithology (after converting the discrete codes to numeric values) or to continuous variables such as geochemical grades. This paper discusses the estimation of continuous (grade) variables using implicit modelling.One of the underlying engines of implicit modelling for producing this mathematical function description is the radial basis function (RBF). In essence, the RBF is a weighted sum of functions positioned on each data point. A system of linear equations is solved to derive weights and the coefficients of any underlying drift model coefficients. Once derived, the RBF may be solved for any unsampled point or averaged over any volume to provide an estimate of grade. It is possible, for example, to query the RBF on a regular grid to derive an estimate of block grades. Given the ease of creation of an RBF, and its ability to predict grade, the question arises as to how the grades derived from the solution of an RBF compare with grade estimates derived from conventional geostatistical interpolation methods (eg ordinary kriging (OK)).The purpose of this paper is to describe in lay terms: the basic structure of an RBF the role of parametric choice in the solution of RBFs and how this influences the character of the solution the fundamental similarities and differences between RBFs and conventional geostatistical estimators.Using a high-resolution conditional simulation, we show that in many situations RBF and OK estimates are very similar.CITATION:Stewart, M, de Lacey, J, Hodkiewicz, P F and Lane, R, 2014. Grade estimation from radial basis functions – how does it compare with conventional geostatistical estimation?, in Proceedings Ninth International Mining Geology Conference 2014 , pp 129–140 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By G Harbort, K Quan

Traditional engineering practice for concentrator design uses a mixture of risk minimisation options and capital minimisation approaches. Often this is based on the preferences and experiences of the engineers involved.A geometallurgical approach involves identifying primary lithology, alteration, and mineral dispersion patterns within a deposit to allow representative samples for test programs. This provides a method to infer from laboratory test results meaningful production data for larger amounts of the ore body. Geometallurgical models can be integrated into the resource block model and subsequent mine plan and can assist in predicting when difficulties in the processing route might be expected, allow adjustment of the design to compensate for these or provide an early warning system so that production forecasts can be more adequately developed. Simulation modelling is the process of creating a computer model of a real system based on mathematical logic. In simulated time, the model explores the randomness and chronological sequencing of events observed on real systems. The objective is to mimic the real system with sufficient accuracy to make predictions of real behaviour under experimental conditions. Amec Foster Wheeler often use the ‘discrete-event’ simulation modelling technique. This method is well suited for inclusion of the statistical variation of effects in unit operation, mechanical availability, throughput and operating strategy (based on historical operating data for equipment downtime), operating schedules and equipment capacity. The net result of the simulation model is an analysis that can quantify risks in terms of system performance and capital and operating costs.CITATION:Harbort, G and Quan, K, 2017. Concentrator design – standard engineering practice versus geometallurgy and simulation, in Proceedings MetPlant 2017, pp 195–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017