Search Documents

By M Hopkins, A Mutale, A E. Vidal da Silva

The Cliffs Nickel Mine extracts a narrow near vertical nickel vein using a mining method of underhand bench stoping with paste backfill. In 2014, at a depth of 400 m below surface, the Northern block of the mine began to experience squeezing within ore development. At first the deformation was localised, within 30 m of the stoping front, but later became pervasive extending across the Northern block and resulting in a hiatus in mine production. The global mechanism is a progressive pillar failure, where the inter-level pillars in advance of the production front could no longer withstand the induced load and progressively yielded. The local mechanism of failure was observed as crushing of the massive sulphide ore and ‘punching’ of the pillars into the ultramafic hangingwall exhibited as floor and sidewall dilation and unravelling of the mafic footwall. The cause of the global mechanism was attributed to a combination of factors, including: high overall extraction ratio, small vertical pillar heights between ore development, high stress in relation to the low rock mass strength, shallow stope front angle, and insufficient ground support capacity. Following the progressive failure, the remnant rock mass conditions across the northern block were severely degraded, with numerous falls of ground that led to a reassessment of the mine plan. Recovery of the Northern block started in 2016 as a staged process. Development of the safe recovery work methodology involved a number of considerations, such as: production sequencing, development access design, ground support, and development of specific procedural controls. The Northern block was then broken into smaller mining precincts based on tactical factors such as location, ease of access, scale of rock mass damage and nickel content. A specific ground support standard and work methodology are employed, while cycle sheets are used to ensure quality and completeness of work. Large intersections showing signs of deformation have either been bypassed or treated using Rocprops to maintain stability during stope production. This approach has been successful in safely regaining access and restarting production in areas that had previously been removed from the mining reserve.

Mar 15, 2021

By R Millar

A frequent challenge in mine water management and mine design is estimation of precipitation and extreme rainfall given a short record of site meteorological data. For remote mine projects, typically only a few years of rainfall data are available, which is far too short for estimation of design rainfall event, such as the 1-in-100 year storm. A frequency-paired approach is presented for comparing daily precipitation records from a mine site with a long-term regional station and provides the basis to transpose the long-term record to the mine site. This allows a long-term synthetic precipitation record to be developed for the mine site that can be used to undertake site water balance studies, determine pond storage requirements, assess water supply options and address other surface water management issues. Conventional approaches are based on chronologically-paired data and when applied to daily data generally yield poor correlations between stations. In the frequency-pairing approach, statistical distributions (two-parameter gamma distribution) are fit to daily data from two stations and used to calculate daily and extreme precipitation values for the short-term site (which is typically a mine or other project site). The method is demonstrated using data from two meteorological stations located along the south coast of British Columbia, Canada. Use of a fitted two-parameter gamma distribution (or other distribution) provides a sound theoretical approach to comparing precipitation data from two sites and the basis for transposing a long-term record to generate synthetic precipitation series and extreme rainfall values at mine sites.CITATION:Millar, R, 2013. A statistical approach for deriving project design rainfall, in Proceedings Water in Mining 2013 , pp 273-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By H Guthrie, J Hodder, J Bain, S Durkin

Australian mines have traditionally relied on diesel powered vehicles to fulfil their light vehicle needs. There are many reasons for the resources industry to review its use of diesel-powered vehicles. The international industry has developed projects to explore the use of Battery Electric Vehicles (BEV) as a more sustainable alternative to traditional diesel-powered vehicles. While the technology for cost-effectively applying modern high-performance lithium-based batteries to the mining environment has existed for over a decade it is yet to be widespread throughout the industry. Through the collaboration of Safescape, 3ME Technology and Kirkland Lake Gold, with funding from Mining Equipment technology services (METS) Ignited, the project has focussed on advancing the Australian METS sector’s capability in the rapidly approaching implementation of BEV technology. This paper reports on the collaborative approach to develop a prototype vehicle; explains the selection criteria for the various components of the vehicle; and details the risk-based approach to developing a scalable product to replace existing underground light vehicle fleets. The prototype vehicle was tested underground at Kirkland Lake Gold’s Fosterville operations in Victoria beginning in October 2019. Reporting from these trials focusses on the key factors affecting underground operations. These include driveability, safety, charging and cycle times. Gathering data around energy consumption through normal daily duties enabled a model of energy consumption and charging requirements to be developed such that various applications of the electric vehicle can be considered against existing diesel-powered vehicles. This has provided insight into the impact on daily operations, and the way forward for large scale implementation.

Mar 15, 2021

By S Maryati

Surface mining activities disturb large areas, produce great sediment loads and tend to be a source of water pollution if they are not managed properly. Coal mining in Indonesia has a very high risk of soil erosion because the coal mining areas are generally located in tropical areas with a high average of rainfall (4000 - 6000 mm/year) and use surface mining methods. The main factors affecting erosion risk are climate, soil type, topography, vegetation cover and management factors. Thus, the monitoring of erosion risk in mining areas is very important due to the characteristics of coal mining in Indonesia. The objective of this research is to determine the ability of satellite images (remote sensing data) and geographic information systems (GIS) to provide an accurate and up to date spatial database for the monitoring of erosion risk in surface coal mining areas using the Universal Soil Loss Equation (USLE) method.The erosion risk analysis and spatial data processing are generated by the ArcGIS 9.3 software and need several data, namely: an erosivity map, erodibility map, a slope map, vegetation index map and land management or land cover map. The erosivity map is derived from the rainfall data, whereas the erodibility map is derived from the soil map. The slope map is derived from the SRTM-DEM (Shuttle Radar Topography Mission-Digital Elevation Model) and processed using 3D analyst tools. Furthermore, the vegetation index map and land cover map are derived from a satellite image using digital image processing techniques.This preliminary study produced results that show soil erosion monitoring, which is integrated with remote sensing and GIS technologies, has great potential for producing accurate, advance, and low cost erosion risk maps in coal mining areas. This map is very important for getting spatial distributions of the erosion and useful for developing erosion management plans.

Nov 22, 2011

This paper examines the complex interplay of deposit characteristics, mining plans, tailings disposal techniques and rehabilitation requirements on planning for mineral sands operations. All component parts of this mining cycle are interdependent and cannot be evaluated in isolation when optimising a mineral sands operation. This is most evident when projects are large-scale or involve resources that contain complexities such as high slimes content, consolidated hard band materials, acid forming materials and radioactive materials. Projects located in environmentally sensitive areas add further to the need for more stringent planning. This paper describes the analysis techniques adopted by Hatch to evaluate mining and tailings placement options for a dredging and floating concentrator system. The principles and methods used in the analysis are applicable to any mining system involving the complexities listed above. The focus of this paper is on the reconstitution of mined material as tailings and the impact of this process on mining schedules and tailings construction and placement options.

Jan 1, 2001

By O Joneydi, J Viljoen, R Funnell

Computational Fluid Dynamics (CFD) modelling is a useful tool that can assist engineers in designing effective ventilation systems for the control of airborne dust generated during mining operations. Thistechnology can save time, effort and the costs associated with re-work or the traditional on-site experimental field trials by running desktop 3D simulations of the various proposed scenarios using state-of-the-art CFD analysis tools. Before implementing a dust management system, an understanding of the behaviour of airborne dust particles in the face zone can be achieved, which can improve the confidence in the secondary ventilation and dust management design. Usingadvanced numerical models, suitable dust extraction strategies can be foreseen, and multiple scenarios can be simulated and investigated quickly. As a case study, dry drilling operations in Kimberlite orebodies produce large quantities of fine dust which poses health and safety risks. An effective dust management system is required to achieve acceptable face conditions. A possible practical solution is a ducted exhaust ventilation system with a force fan in the face zone. This paper demonstrates how CFD analysis can be used as a tool to assist the design engineer with validating and optimising the proposed ventilation design by tracking the trajectories of different size dust particles, to determine the best equipment layout and appropriate flow rates which minimises airborne dust.

Oct 12, 2022

By D Cliff, B Belle

Trigger action response plans (TARPs) are inherent to managing multiple hazards such as high gas content with multiple coal seams, high spontaneous combustion propensity, heat and ventilation. TARPs aim to provide assurance and guidance when the situation deviates from the original plan or there is a change in conditions that could be hazardous. Over the years, learnings from various incidents have continuously required coal operations to revisit the TARP trigger values that were based on historical data or guidance values from the industry. In most cases, the background to the basis of TARP statistical data (ie average, maximum, hourly or daily for the monitoring or sampling location) is unknown. The introduction of real-time monitoring devices to monitor gases and airflows has provided greater understanding of the hazard scenarios and their controls. This paper analyses the carbon monoxide data from operating longwall mines and compares these with the historical trigger values to understand the changes and identify improvement opportunities while setting trigger levels in the TARPs. As an example of setting trigger values, those used during the sealing of a panel are explored in terms of setting values based upon the sampling location and the level of risk. It is envisaged that the learnings shared herein will further enhance the understanding and management of multiple hazards in Australian coalmines.CITATION:Belle, B and Cliff, D, 2015. Improved trigger action response plan development based upon mine-specific data, in Proceedings The Australian Mine Ventilation Conference, pp 73–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D Adhikary, M Khanal, B Poulsen, H Guo

During longwall mining, the ability to reliably estimate the height of longwall mining-induced fractures is critically important in order to effectively manage mining-induced water inflows and aquifer interference. The extent of mining-induced subsurface deformation, fracture, surface subsidence and aquifer interference is largely controlled by local lithological conditions, mining methods and mine layouts. Therefore for the purpose of quantifying mining impacts it is imperative to incorporate the local geology and mine plan parameters in a mine scale model. Two different numerical models based on 3D continuum (Finite Element Method) and 2D discrete (Discrete element method) domains, respectively, are developed to incorporate the mine site parameters of a study site in Australia. Both the models are calibrated and validated with measured mine data. The continuum numerical modelling method is used to investigate the change in permeability of the overburden strata due to underground extraction considering the full 3D nature of geology and mine layout. The discrete element modelling method is used to simulate the initiation and propagation of fractures, allowing the caving of overburden strata to be represented in a realistic manner, and the permeability enhancement of the strata overlying the goaf to be calculated from first principles. Permeability enhancement in the discrete element model is a direct function of the fractures induced in the deformation/caving process; fracture location, extent, aperture and connectedness. From the numerical modelling under the simulated condition for the mine studied here, it is predicted that the permeability of the caving zone from the goaf to five times the mining height increases by almost six orders of magnitude. In the fracture zone to approximately ten times the mining height, the change in permeability is predicted to be around two to three orders of magnitude. At the height of more than ten times the mining height the magnitude of permeability increased is predicted to be one to two orders of magnitude. CITATION:Khanal, M, Poulsen, B, Adhikary, D and Guo, H, 2018. Modelling of height of connective fractures during longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 254–265 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Using Dynamic Simulation Throughout a Process Plant's Life Cycle

Sep 13, 2010

By D T. Ribeiro, J F. C L Costa, J C. Koppe

Drilling and sampling are responsible for most of the costs during mineral exploration, especially in multi-elements and polymetallic deposits, such as iron, manganese and bauxite deposits. On these deposits, often it is necessary to estimate multiple attributes at several granulometric fractions, ie distinct particle sizes. This paper investigates the effect of sampling at a close spacing grid only the head grades for the multiple chemical species in iron ore deposits. The remaining required data at the various grain sizes are sampled at a sparse grid. The derived geological model is checked for precision and accuracy comparing the output obtained against a model obtained using a complete isotopic data set including head grades and chemical analysis at each granulometric fraction analysed at all sampled positions. Among the several tested alternatives, the best procedure for dealing with the posed problem involved utilising the correlation coefficients between the grades at distinct fractions to obtain an isotopic database prior to interpolation. Cokriging was the method used, based on the intrinsic coregionalisation model. Estimates were obtained with the quality needed for the proposal of the study. Results showed that at least 50 per cent of the blocks were estimated with errors less than ten per cent relative to the grades obtained at the reference model, using only 15 per cent of the granulochemical data employed to obtain the reference model. The methodology also preserved the correlations between the attributes in their several granulometric fractions on the estimated model.

Sep 26, 2011

Alluvial mining even of shallow deposits is often economically a marginal proposition and causes significant disruption of the land surface through the need for large scale excavation. In-situ leaching using chlorine-based solutions eliminates the need for excavation, the disruption of surface activities, and may greatly reduce processing costs and improve recovery especially of fine gold. A spreadsheet model has been developed to design and analyse the economics of in-situ leaching of alluvial deposits. In-situ leaching of shallow deposits may be achieved in a number of ways including solution infiltration via perimeter ditches or the use of injection and production wells. In most instances deeper alluvials may only be processed using well systems. Two deposits are analysed in this paper. The first consists of one metre of payable wash beneath one metre of overburden. Some thirty fields per year are treated processing 450 000 BCM per year at a cut-off grade of around $4/tonne ($8/rn3 or the gold value equivalent of 0.26 gh or 0.52 g/m3). The principal costs are well drilling and labour. Sensitivity analysis indicates that doubling the throughput halves the cost. The economics of the project are relatively insensitive to reagent costs and consumptions, and halving the recovery doubles the cut-off grade. Shallow deposits treated using the infiltration ditch system may be marginally cheaper and more conveniently managed although this depends on the relative cost of digging the perimeter ditches. In a second example, deep leads with one metre of wash beneath 30 metres of overburden necessitate significant drilling and feature reduced throughputs as a consequence. In the example chosen 30 fields a year are processed for an annual throughput of 65 000 tonnes costed at around $20/tonne (1.4 g/t Au equivalent, $40 /m3). Sensitivity analysis indicates that throughput, and drilling cost per metre are not important but there is a high sensitivity to recovery and to the depth to payable wash.

Jan 1, 1992

By R K. A Taylor

The growth in production of beneficiated ilmenite products has been one of the most significant trends in the titanium feedstock industry over the past 30 years. In this period, the production of titanium slag and synthetic rutile has grown five-fold to the point where these products represented 56 per cent of total feedstock production in 2000. Additional production capacity is being proposed as the core component of new feedstock supply projects presently under consideration. A high proportion of these products is based on technologies for which the inherent quality of the is an essential factor. Location specific factors also play a large part in determining the cost of production. As the demand for such products grows, and the availability of favourably located sources of ilmenite of suitable quality declines, it can be expected that existing beneficiation technologies will become increasingly constrained. Existing beneficiation technologies, and those which have been developed, but are not yet commercially applied, are reviewed. Future issues which are likely to impact on the cost effectiveness of these technologies, or the quality of final products, are identified. These factors suggest directions for development of ilmenite beneficiation technologies to achieve economic production of the quality of feedstocks which will be demanded by the TiO2 pigment industry in the future.

Jan 1, 2001

By Nikaido M, Kanda Y

A rotary type separator has been developed which separates particles on the basis of their shape. This separator was applied to a particle size range of about 50 - 120 ¦m, and to our present knowledge may be the smallest size range ever to be separated. A theory of the separation is given based on the difference of an adhesive force of the particles: the adhesive force between spherical particles and plate is more powerful than that of irregular shaped particles for the same particle size. These facts have been ascertained by the measurement of an adhesive force by a centrifugal method. US and Japanese patents have been obtained on this separator, which consists of a borosilicate glass cylinder of 150 mm outside diameter, 120 mm in width, and an AC electromagnet. The samples used in this study were mixtures of spherical glass particles and non-spherical shaped glass particles. The results are summarised as follows. In the case of mixtures of spherical particles and irregular shaped particles in the weight ratio of 1:1, the spherical content of the spherical product became 70 per cent - 75 per cent, and in the case of 3:1, the content became 87 per cent - 90 per cent, as the result of one separating operation. However, for a mixture of somewhat rounded particles and irregular shaped particles of weight ratio 1:1, the rounded content varied between 58 per cent - 73 per cent. The feed rate of the particles mixtures was about 0.3 g/min. Newton's Efficiency was 20 per cent - 60 per cent. The separator may find application in shape separation of ceramic powder, metal powder or industrial diamond powder.

Jan 1, 1993

The author describes 1. The classification and characteristics of various thick seam mining techniques in various Japanese coal mines. 2. Practices of thick seam mining methods experienced in Taiheiyo Coal Mine. Currently, thick single lift, simultaneous multi lift and non simul- taneous multi lift mining methods are adopted as underground flat thick seam excavations in Japan. These are now reliable and effective in increasing the extraction ratio. At Kushiro Colliery of Taiheiyo Coal Mining Co., these three thick seam mining methods have been used. According to the results, if solidification of the top lift goaf is essential, the non simul- taneous multi lift mining method is the most effective in increasing the extraction ratio without minimising productivity of each lift and it points out that further development of this method is necessary.

Jan 1, 1976

Gravity gold recovery has been practiced for thousands of years, making it one of the oldest forms of mineral processing. Gold is 19 times heavier than water although the barren rock is generally only 2.7 times heavier. Any potential gold ore needs to be characterised to assess its amenability to a gravity recoverable gold (GRG) process based on well planned and executed test work. Scale up considerations need to be considered in designing a gravity circuit. The economic impact of a gravity circuit should be justified based on the installed cost and likely benefits. Maximising gravity gold recovery results in a faster cash flow, lower operating cost per ounce and higher overall gold recoveries compared to the several weeks required to recover gold adsorbed onto carbon. The advent of centrifugal concentrators such as the Knelson and Falcon, coupled with intensive leaching of concentrates (ILR), has revolutionised gravity gold circuit designs. Considerations associated with the sizing of the centrifugal machines and the percentage of the circulating load (bleed) that should be processed is discussed in this paper. The trends with gravity circuit layout, engineering, as well as optimum dumping cycles, are important areas which require close consideration. Key aspects of these are presented in this paper. There are a number of circuit configurations to be considered, including the integration of different gravity concentrators. Other gravity process design considerations such as fewer modules, the effect of equipment size and enhancement of process efficiency using preconcentration, together with factors that affect OPEX and CAPEX are addressed. Practical considerations of maintenance, security from theft, minimisation of risk and water balance considerations are discussed using different equipment and circuit configurations. The trend towards using gravity recovery in flotation plants is also reviewed. A number of examples are cited and good design aspects highlighted.

Aug 1, 2010

By O Salisbury

Ingress of air into the longwall goaf environment needs to be managed appropriately to reduce the risk of creating a spontaneous combustion event. The maingate goaf edge is an area of particular concern in this respect, as air often penetrates for some distance into the goaf along this region inbye of the longwall face. Since the flow rate in this part of the goaf is also quite low, an opportunity exists to disrupt the air pathway by implementing a barrier to the airflow. Previous attempts using plugs made from an assortment of materials have resulted in varying degrees of success. More recently, Narrabri Coal Operations (NCO) has introduced the use of a chemical foam that is mixed with nitrogen to produce a standing barrier with the consistency of shaving cream. The implementation of this practice has consistently proven to be very effective for reducing the oxygen concentration along the maingate goaf edge by systematically retreating the foaming unit with the longwall. This paper presents how the foam is applied in the underground goaf environment to prevent oxygen ingress and uses results from gas monitoring to confirm the foam effectiveness.

Oct 12, 2022

By S Wellink, D Chalmers, D Adermann, C Martin

The practice of recording blasts for quality control purposes has been conducted for several decades. However, at the low frame rates of a standard video camera, essential data is frequently missed as it occurs when the shutter is closed between frames.The use of high-speed video for the research, development and monitoring of the performance of blasting procedures is a well proven but under-utilised practice.The recent development of low cost, easy to use high-speed digital cameras and user friendly software can deliver a capability into mine management as a day-to-day production tool that can greatly improve blasting performance and reduce costs.Digital high-speed video and image analysis software can accurately quantify each blast. Analysis of the images can facilitate the identification of causes of variance from design, geology changes, errors in blast practice and areas of poor performance. The use of high-speed video greatly enhances the audit and review processes so that future blast design can be quickly and appropriately modified to deliver improved blasting performance and reduced costs.The three videos demonstrate the differences between standard video and high-speed video and the detail that can be obtained from them. These videos of open cut blasts can be used to identify blast performance variances. Capturing images at 1000 frames per second allows the analysis on a millisecond timescale where detonator timings, fragmentation, venting, fume generation and flyrock can be accurately identified.CITATION:Adermann, D, Chalmers, D, Martin, C and Wellink, S, 2015. High-speed video – an essential blasting tool, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By B Roache

Ground support installation into the face of development headings has become an accepted practice at many Australian hard rock mines. Ground support is installed in the development face to reduce personnel exposure to rockfall while conducting work tasks such as marking up, installing lifter tubes, charging, and face sampling. The ground support system installed in the face is typically friction bolts and mesh. This support system can be effective at reducing rockfall occurrence, but it also increases the cost of development per metre, in terms of capital for the ground support, jumbo and operator capital allocation and the installation time slowing each drill and blast cycle. Other issues associated with meshing and bolting the development face include management of rock bolts and mesh sheets in the fired dirt of every cut, damage to services such as vent duct, geometry issues when installing ground support onto irregular development profiles and operator error. Fibrecrete installation onto the development face for support is an option considered by many mines, but it can be difficult to manage due to the removal of visual indications of misfires and slowing the mining cycle due to the wait time for fibrecrete curing. The use of Thin Spray Liner (TSL) products in underground hard rock mines has been relatively infrequent in the past, mainly due to issues with cost, health and safety, and liner strength. Kanmantoo Mine investigated the use of TSLs for the purpose of development face support, while collecting data on the costs and practicalities associated with their use. Several TSL products were trialled and a preferred TSL product was selected for use as face support. Cost savings, drill and blast cycle timing improvements and other benefits were achieved while meeting the requirement to reduce rockfall risk.

Mar 29, 2023

By P K. Wong, D A. F Oliveira, F M. Azad

In situations where foundation piles are located in proximity to existing or future tunnels, it is typical for the tunnel owner to require that sleeving of the piles be carried out to at least the invert of the tunnels to minimise any load transfer to the tunnel lining. In competent rock, this practice may be sometimes unnecessary, thus uneconomical. This paper presents an assessment of the effect of pile loading from one of the multi-storey buildings at Barangaroo South in Sydney on the adjacent future Sydney Metro tunnels. It was originally required by Transport for NSW (TfNSW) that the piles be sleeved below the tunnel invert level; however, the building developer wanted to reduce the pile sleeving depth to achieve a more economical solution due to the large number of load transfer piles being required for the project. To assess this feasibility, a full 3D commercial numerical code, FLAC3D, was used to carry out this complex soil-structure interaction analyses. Based on these assessments, it was demonstrated successfully to the TfNSW that the pile sleeving may be terminated at 2 m above the tunnel invert level. For this arrangement, the investigations found that the loading on the piles should have negligible adverse impact on the tunnel lining design. As a result of such an assessment, the proposed pile sleeving level was approved by TfNSW, thus offering an economical foundation solution for the project.CITATION:Azad, F M, Oliveira, D A F and Wong, P K, 2014. The impact of pile loading on adjacent metro tunnels – Barangaroo South, Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 355–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Duran

When dealing with rocks in the geotechnical profession, a common activity involves providing an estimate of the intact strength. The tactile approach and descriptions of strength that apply to soils is well documented, can be readily checked through the use of a pocket penetrometer and are known to provide reliable estimates of strength. Moreover, although different soil strength classification systems are present, the bounds between classification classes are compatible across almost all documented classification systems. However, this is not the case for rock strength materials. There are numerous systems within the literature, some with different concepts, and almost all have different bounds to each strength classification. In this paper, the author presents seven classification systems for estimating intact rock strength and highlights issues in their implementation. Example cases are presented to discuss the typical concerns confronting field strength estimates.CITATION:Duran, A, 2014. Comparison of field estimated strengths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 101–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014