Search Documents

By J G. McLellan, B Miller

Copper and Gold mineralisation at the Ernest Henry deposit is bound by two controlling shears along the hanging wall and footwall margins. The shear zone geometries have been influenced by a large diorite intrusion, dated at ca. 1660 Ma, which lies to the north-east and south-west of the main orebody. The shear zones, which partitioned strain prior to the main mineralising event ca. 1514–1504 Ma, and in conjunction with adjacent regional structures, have been a critical factor in the deposit location and geometry. Conventional exploration techniques have been utilised proximal to the current deposit since the initial discovery in order to expand upon known resources, with limited success. However, new geomechanical modelling techniques have now been employed to target structurally controlled mineralised zones in three dimensions. The main aim of the geomechanical modelling was to simulate the effects of regional deformation events to highlight areas of anomalous strain, which indicate areas with a higher likelihood of fluid focusing and mineralisation potential. This project was focused on testing the latter stages of a D3 event (NE-SW compression) to examine preconditioning of the system, and a D4 event (SE-NW compression) which have ultimately been responsible for the current location of the mineralisation.CITATION:McLellan, J G and Miller, B, 2017. Geomechanical modelling of the Ernest Henry iron oxide copper gold deposit – identifying fluid pathways to predict potential mineralised zones, in Proceedings Tenth International Mining Geology Conference 2017, pp 75–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J Janus, J Krawczyk

Local accumulation of methane in workings of a longwall is one of the most common causes of mining accidents. This gas has many sources: it may leak from goaf through permeable sealings, or through gaps between roof support sections. This stream is then mixed with ventilation air. In the case of auxiliary ventilation ducts, or free jet fans, we have to consider the propagation of a clean air stream in areas with an air-methane mixture. Therefore, modelling the mixing process of methane with ventilation air is important for determining the hazardous areas and thus to ensure safety. Computational fluid dynamics (CFD), specifically the finite volume method, provides tools for such modelling. However, this method requires validation. For this purpose, we have compared measurements with simulations for selected test cases having sufficient similarity to the present problems. In typical methane explosion hazard areas, such as a longwall, it is difficult to make measurements sufficiently to confirm credibility of 3D CFD simulations. As a relevant alternative, an injector methane drainage station placed in an underground gallery has been selected. The stream of drained goaf methane is entrained by compressed air powered injectors and then mixed with ventilation air. Research in this area does not interfere with mining operations, it can be performed safely in a repeatable way. Flow within the site has many similarities to conditions in mine drifts of the longwall area. Comparative research of measuring the methane concentration distribution in the mine drift downstream injector station, with simulations of propagation of the methane stream, was carried out. For measuring the methane concentration distribution in the mine drift a multipoint measurement velocity system developed at the Strata Mechanics Research Institute was used. For the simulation a finite volume method for turbulent flow of gas mixtures was applied. Preliminary results of comparison are shown as graphs and tables.CITATION:Janus, J and Krawczyk, J, 2013. An analysis of the mixing of air and methane in the stream produced by the mine injector station - Presenting preliminary results of measurements and modelling, in Proceedings The Australian Mine Ventilation Conference , pp 49-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By C D. Rose

A review and summary of the results of 120 coal sampling system bias tests is presented. This review supports new methodology using multivariate statistics currently being considered by ISO TC27 SC4. The current difficulties with ISO 13909-8 are explained and the logic behind the current new working draft is discussed in detail. Bias was detected in nearly 36 per cent of tests reviewed, suggesting that much improvement is needed in designing, maintaining and monitoring the performance of sampling systems in order to avoid sampling bias.CITATION:Rose, C D, 2012. Bias testing of mechanical sampling systems for coal - A review of test results and call for use of multivariate statistical analyses, in Proceedings Sampling 2012 , pp 185-192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By E A. G Marques, P M. Dight, T A. V Costa, K Mercer

Brazilian banded iron formation (BIF), known as ‘itabirite’, is the main host rock for iron ore in the Iron Quadrangle mines, Brazil. Their geneses are controversial and it is agreed that diagenetic, metamorphic and tectonic events, as well as weathering processes, were responsible for the iron concentration. In addition, it is understood that weathering processes are mainly responsible for reducing the original high intact rock strength, and for generating deep weathered profiles with low strength rocks commonly observed in Vale’s mines.A considerable amount of work has been done to correlate the macro and micro aspects of the itabirites as physical, chemical and geotechnical characteristics that directly or indirectly affect the intact rock strength; however, it is not yet clearly understood what effects the weathering processes have on the strength reduction of these rocks and its associated impact on pit slope stability. This forms a key focus of the lead author’s current research work.This paper presents a review of the geological, geotechnical and weathering characteristics of the itabirites, and early results for the evaluations of fresh itabirites from the PhD thesis research being undertaken by the authors at the Australian Centre for Geomechanics, School of Civil, Environmental and Mining Engineering, The University of Western Australia, sponsored by Vale SA.The results showed that to evaluate the density and unconfined compressive strength (UCS) correlation, not only the porosity but also the geological features should be considered, as they are responsible for data dispersion; however, the presented data suggested a trend that provides the confidence to develop advanced studies and a data population increment to establish proper correlations to support a reliable UCS method.CITATION:Costa, T A V, Dight, P M, Mercer, K and Marques, E A G, 2015. An overview of the weathering process, preliminary density and unconfined compressive strength correlations for fresh itabirites in vale mines on the western side of the Iron Quadrangle, Brazil, in Proceedings Iron Ore 2015, pp 241–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D S Wallis

Northern Australia leads in world-class mineral deposits' is a bold statement. First there must be a starting point. Land north of the Tropic of Capricorn (23¦ 26' 5") will be regarded as Northern Australia covering nearly 40 per cent of the land surface of Australia. As opposed to land south of the Tropic of Capricorn, it should be regarded as Tropical Northern Australia and for the sake of brevity, (TNA) Refer Figure 1. Apart from the tyranny of distance from centres of power and population in the temperate zone, it suffered in the past from the belief that the tropics are unsuited for European workers and from the lack of infrastructure. Outstanding mineral deposits of iron, base metals, gold and diamonds, discovered and developed in the past three decades, provided the substance for the title. There are many world-class mines producing and there are mineral deposits neutralised through Government policy. TNA can maintain its lead in world-class mineral deposits provided Government policy will stop partitioning the land and decreasing that available for exploration. Let's look at what we have that is world-class. In Western TNA iron ore deposits at Paraburdoo, Mt Tom Price, Marandoo, gold at Telfer, diamonds at Argyle. In central TNA uranium at Ranger and Jabiluka, lead-zinc-silver at McArthur River, gold at the Tanami, manganese at Groote Eylandt and bauxite at Gove. In eastern TNA Mt Isa, Hilton, Century zinc-lead, bauxite at Weipa, gold at Kidston, Mt Leyshon, magnesite at Yamba and coal mines in the Bowen Basin. Those mines or deposits stand out yet are only an indication of the numerous lesser mines and of mineral deposits depending for development on market demand and/or changes in Government policy, eg 'The Three Mines' policy. Very large areas of mineral rich structures in the western, central and eastern parts of TNA are concealed below flat lying comparatively young unmineralised sediments. The Great Artisan basin sediments in eastern TNA can and do host oil shale and non metallic minerals. Nearly 40 per cent of western TNA is covered by the Great Sandy Desert. The Canning Track, with a series of 54 wells, was constructed by surveyor Alfred Canning in 1908 - 1910 with great difficulty. It extends 1700 kilometres from Halls Creek in the north to the gold town of Wiluna in the south, through the Great and Little Sandy Deserts. Gold explorers are following favourable structures extending to the north east below the sediments and sand hills covering the track. Half of central TNA's mineral structures are concealed by the Tanami desert and the Cretaceous sediments covering the pastoral regions of the Barkly Tableland and the Daly Waters to Top Springs pastoral areas. The Georgina Basin in the south eastern section is part of the concealment.

Jan 1, 1994

By D Timms

The Kempfield deposit is located in the Hill End Trough, one of several intracratonic basins developed during Silurian–Devonian time, in the eastern province of the Lachlan Orogen, Eastern Australia.The deposit contains an oxide resource of 5.8 Mt @ 58 g/t Ag and a sulfide resource of 14.4 Mt @ 45 g/t Ag, 1.7 per cent Zn and 0.6 per cent Pb, classified and reported in compliance with the JORC Code. The deposit has been previously explored by a number of companies, including INCO, Shell, Jones Mining, Golden Cross Resources and recently Argent Minerals Ltd (Argent). Argent is currently completing a definitive feasibility study with a view to mining the deposit.The deposit is hosted at the boundary between the Molong High to the west, comprising Ordovician sediments and volcanic rocks and the Hill End Trough to the east, interpreted as a back-arc basin containing Silurian sediments and siliceous-feldspathic volcanic rocks. The boundary between these two strato tectonic units is an imbricate thrust fault zone known as the Copperhannia Thrust.The Kempfield deposit is hosted in felsic volcanic rocks known as the Kangaloolah Volcanics. These have been in-faulted and folded into the Middle Ordovician meta-sediments of the Coombing Formation of metasediments along the Copperhannia Thrust. The Kangaloolah Volcanics belong to the Late Silurian Mumbil Group, comprising submarine carbonate-shale facies interspersed with extensive felsic volcanic piles, which grade conformably upwards into turbiditic sandstone and siltstone sequences (interpreted to represent a deeper depositional environment). These turbiditic rocks are known as the Campbells Formation, comprising siltstone, sandstone and andesitic tuff. The rocks at Kempfield are metamorphosed to lower greenschist facies, reflected through the different type of schists.Silver, gold, lead, zinc mineralisation is hosted in barite-rich horizons, near the boundary to quartz-phyric tuffaceous rocks in submarine, immature, reworked felsic ash tuffs. Barite appears to be hosted in greatest concentrations by the coarser grained volcanoclastic sandstones and grits, whilst intercalated siltstones are volumetrically minor and tend to return low barite and silver. Mineralisation is hosted in stratiform and probably stratabound barite-rich horizons. A northeast-trending, steeply dipping, metamorphic cleavage (S1) occurs throughout the project area.

Aug 22, 2011

By M K. Nahian, R G. Reddy

The thermodynamic model for species distribution in aluminium chloride (AlCl3) and 1-butyl-3- methylimidazolium chloride (BMIC) system was developed. The experimental thermodynamic data, considering a range of aluminium chloride species, such as AlCl4-, Al2Cl7-, Al3Cl10-, Al4Cl13-, and Al2Cl6 were used in developing the model. When the XAlCl3 was in the range of 0 to 0.50, only anion species Cl- and AlCl4- were existing in the solution. As the XAlCl3 value increased more than 0.50, the available anions were Al2Cl7-, Al3Cl10-, Al4Cl13-, and Al2Cl6. Specifically, the concentration of Al2Cl7- increased in the composition range from 0.50 to 0.67 XAlCl3, after which it decreased. This change in the concentration of Al2Cl7- was due to its reaction with excess AlCl3, leading to the formation of Al3Cl10-. The average cathode current density was determined by the electrochemical experiments varying XAlCl3 from 0.50 to 0.71 in the AlCl3:BMIC solutions. The average cathode current density increased as the XAlCl3 increased from 0.50 to 0.67. However, it decreased when the XAlCl3 > 0.67. This trend can be attributed to the electroactive species Al2Cl7-. The Al2Cl7- promotes the reduction rate at the cathode, resulting in an increase in the average cathode current density.

Aug 21, 2024

By C M. Standen

The SAG mill at Rasp Mine has undergone a number of liner design modifications since commissioning in 2012, making liner wear and failure difficult to predict from historical data. During 2017, several instances of liner failure or near failure were experienced resulting in unplanned downtime for emergency relines or to patch liners in the lead up to a planned shutdown. The strategy for relining mills is often to minimise the frequency of relines (and subsequent shutdown costs) by extending liner life, achieved through design modifications. However, it was observed that as the Rasp SAG mill liners wear, mill performance declined with power draw increasing and throughput declining. Opportunity and inefficiency costs start to erode the revenue per additional tonne milled for a given set of liners, and in turn the benefit of delaying relines. As such, optimising the frequency of relines becomes a trade-off between reline costs and opportunity/inefficiency costs in delaying relines. The aim of this paper is to demonstrate a frame work for analysing costs using a marginal economic analysis with the assumption that the Law of Diminishing Returns can be applied to the life of mill liners. The SAG mill operating variables can be modelled to determine their impact on costs and an optimal reline point can be defined where the total costs are minimised. This prevents unexpected failures due to accelerated wear by providing justification to reline earlier and thereby allowing efforts to be focused on sustaining milling performance.CITATION:Standen, C M, 2018. An economic approach to optimising mill reline frequency – a case study of SAG mill relines at Rasp mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A Remes, A Dennis, M Talikka, T Kotiranta, S Horn

A mine project combines vast amounts of information from various disciplines including but not limited to geology, mining, metallurgy, technology, environment and economics. In many cases, all relevant information is not fully shared between all disciplines. Thus, project performance (technical, economical and sustainability) may be evaluated on basis of insufficient information resulting in non-optimal decisions, project execution and risk management. Advances in computing power and simulation software enable various data sets to be incorporated in a single digital platform enabling more efficient and transparent data sharing. In addition, linked data sets and simulation can support assessment and optimization of the project as a whole rather than focusing on optimization of individual events. CITATION:Horn, S, Remes, A, Kotiranta, T, Talikka, M and Dennis, A, 2018. Evaluation of sustainability of copper production value chain from ore to metal using advanced simulation, in Proceedings Life-of-Mine 2018, pp 87–89 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By D Kilkenny, D Nardini, P Kline

This paper is a case study highlighting learnings and success in two areas challenging underground miners: change management and collaboration. It examines the implementation process of a new automated loading system in the bulk stoping area of Telfer Mine in Western Australia, controlling multiple load haul dump machines. Here, the new technology has brought together different functions and different companies to deliver a well performing automation system in a changing and challenging mining environment. The introduction of a new and different technology on site has driven collaboration between all stakeholders to break down the traditional barriers to achieve the sustained performance required. Historically, different teams have operated within silos and not always aligned to deliver a ‘best for project’ solution. Technical teams focus on the mine design, maintenance teams focus on reliability and operations execute the plan. Mining contractors focus on productivity and cost. Manufacturers focus on supply of goods and service. Optimising each silo individually is not guaranteed to provide an optimal mining solution. Involving elements from each team as seen at Telfer, has resulted in an optimal mining solution for the automated loading system. A change of focus from the technical teams to include automation parameters in the mine design; operability and maintainability built into the system design allowing for collective ownership and responsibility resulting in a more resilient solution. The implementation of the new technology was not only a technical change but more importantly, successful management of change. Elements of successful change management such as communication, vision, leadership and planning, are essential to harness a trusting site culture which is responsive to new technology. Learnings and challenges from this change process will also be discussed with the intent to improve the success rate and timelines of technology implementations in the future.

Mar 15, 2021

By B Chapman, B Gaida, L Drowley

The 372 MW Ulu Jelai Hydroelectric Project is a peaking power scheme located in the Cameron Highlands, Malaysia. The main features of the project include an 84 m high roller compacted concrete dam; two weirs which divert flows from adjacent catchments via transfer tunnels into the main reservoir; an underground power waterway; and an underground power station complex comprising three large caverns with connecting tunnels approximately 240 m below surface level. The project includes approximately 25 km of tunnels excavated in fresh granite rock mass with some distinct shear zones of weaker material. The majority of the tunnels are being excavated using drill and blast, with the two transfer tunnels being excavated with a tunnel boring machine (TBM).This paper focuses on the design and construction of the Telanok underground power station complex and also some aspects of the design for the headrace tunnel. Topics covered include geological site investigations including in situ measurements of rock stresses; development of a geological model and parameters for rock support design; three-dimensional modelling to assess interactions between the caverns to optimise rock support; design of a rock anchored crane beam; construction of the caverns and design of the unlined headrace tunnel taking into account hydraulic jacking and operational pressure fluctuations.CITATION:Drowley, L, Gaida, B and Chapman, B, 2014. Design and construction of large caverns in granite – Ulu Jelai Hydroelectric Project, Malaysia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Rafty, A Markham, S Atkinson

Australia contains some of the most productive mining areas and is characterised by ancient landscapes and highly variable hydrology. Historical mining of iron ore, coal and other minerals has targeted ore deposits located above water tables, and elevated above creek lines where possible to reduce cost. The downturn in mining caused by falling ore prices over recent years has triggered a drive to reduce cost, maximise yield and delay capital expenditure associated with opening new mines. So as the ore deposits with more favorable mining conditions become depleted there is an increased focus on mining ore associated with valley floors and creek lines. This is demonstrated by a regional assessment of the extent of Channel Iron Deposits (CID) and Iron Ore (Fe) Mines and Deposits in the Pilbara Region of Western Australia (Figure 1). A large proportion of these mines are, or plan to, target high grade CID ore associated with existing creek systems. Figure 2 shows outcropping and inferred sub-cropping CID extents, which suggests there are vast quantities of CID ore deposits throughout the Pilbara Region, intersected by major creeks which could be mined at some point in the future using creek diversions (Atkinson et al., 2017). A similar picture could also be produced for coal mining in Queensland, particularly in areas such as the Bowen Basin.While creek diversions provide an opportunity to maximise the utilisation of these orebodies and extend the life of mine, creek diversions can involve substantial financial, social, environmental and regulatory risks that need to be carefully managed (Markham et al., 2017, Atkinson et al., 2017). This paper discusses the key issues and opportunities associated with diversion decision making. It highlights the importance of using a well-structured assessment methodology that allows key stakeholders to be part of the assessment process and is complementary to material presented in Atkinson et al., (2017). Design considerations for operational and closure designs are presented, as well as mine planning considerations, risks, cost saving opportunities and the benefits of an integrated approach to design. The role technology plays in diversion design and performance monitoring is discussed as are the potential opportunities for the future.CITATION:Atkinson, S, Markham, A and Rafty, M, 2018. Diversion decision making with an integrated approach to design for operations and mine closure, in Proceedings Life-of-Mine 2018, pp 74–79 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By O N. Savassi

A rigorous methodology for prediction of flotation plant performance is presented, which is based on a standardised batch flotation test called the MFT. The work is part of the FLEET program, developed by MinnovEX with the support of seven large mining firms. The methodology is divided into three key steps: direct measurement of the kinetics of true flotation in the pulp, independent of hydraulic entrainment and other froth effects in the batch cell; benchmarking of the industrial plant over a broad range of ore types and operation conditions; and model calibration to describe froth effects in the plant, with a minimal number of parameters. To date, the methodology has been applied with success at several industrial plants, encompassing copper, gold, nickel, iron, lead, zinc and coal operations. This paper includes a description of the laboratory testwork procedure and scale-up to full industrial circuits. Examples of industrial application are also presented.

Jan 1, 2005

By H F. Yu, S Ueda, J Diao, W F. Gu, Y Sasaki, H Qin

The main reason for the underutilisation of steelmaking slags is their instability, which is influenced by their complex phase structure. Recycling and sustainable steelmaking slag face challenges due to the presence of magnesium oxide (MgO), a crucial component in steelmaking slag. This study investigates the phase evolution of steelmaking slag during the cooling process with different MgO contents, using high-temperature experiments and FactSage™ software, ver 8.1, (by Thermfact/CRCT and GTT-Technologies) thermodynamic equilibrium calculations. X-ray diffraction (XRD) and scanning electron microscope - energy dispersive x-ray spectroscopy (SEM-EDS) analyses identified main phases in steelmaking slag, including Ca2SiO4 (C2S), RO (MgO-FeO solid solution), Ca2Fe2O5 (C2F), and Ca3SiO5 (C3S). The study reveals that RO phase increases as the MgO content increases. C3S precipitates from steelmaking slag with a 12 mass per cent MgO content at a reduced temperature of 1400°C. It is important to note that C3S remains in the steelmaking slag even after slow cooling. This may be due to the substitution of Ca2+ in C3S by Fe2+ and Mg2+ ions. Intriguingly, the precipitation of f-CaO in steelmaking slag with 10 mass per cent of MgO content occurred after one year, while there was no manifestation of f-CaO precipitation in the steelmaking slag with 12 mass per cent of MgO content even after one year. This discrepancy suggests a potential stabilising effect of an appropriate amount of MgO in steelmaking slag. However, it is crucial to emphasise that this inference lacks supporting data, necessitating further research to validate this hypothesis. The significance of this work is in uncovering the complexities of steelmaking slag behaviour, providing essential insights for optimising recycling processes. The research sheds light on the factors that influence the phase composition and stability of steelmaking slag, contributing to the utilisation of steelmaking slags, promoting environmental sustainability, and enhancing the overall efficiency of metallurgical processes in the current industrial landscape.

Jun 19, 2024

By M I. Pownceby, M A. Rhamdhani, D M. Fellicia, S Palanisamy, R Z. Mukhlis

The trend of global copper production has prospectively increased over time. Based on typical mined ore grades, 1 t of copper ore generates approximately 6–10 kg of copper, which requires much energy, usually in the form of metallurgical coke. Copper production using carbon as a fuel and reductant contributes up to 0.3 per cent to global greenhouse gas (GHG) emissions. As a result, research into decarbonisation processes applicable to reducing low-grade copper sulfide ores, copper oxides, electronic wastes and other alternative complex Cu-rich materials has increased. Alternative fuels for reducing carbon-rich emissions in pyrometallurgical copper processing include methane, ammonia, biomass, solar and wind power, but in recent times increased focus has been on hydrogen as a potential fuel and reducing agent for materials such as oxidised copper scrap, Cu2O/CuO and Cu-rich slags/e-wastes. From a thermodynamic perspective, hydrogen exhibits a significantly more negative standard Gibbs free energy (ΔG°) than copper oxide making it a suitable reductant and the exothermic thermal effect from reaction between hydrogen and Cu2O/CuO may be used to control process parameters. These characteristics renders hydrogen an ideal gas for reducing copper oxides and copper-containing slags/e-wastes. This review article assesses previous research on utilising hydrogen for producing and refining copper from primary and secondary feed materials.

Jun 19, 2024

Visual computing opens the design process to a wider audience and allows rapid communication of mine plans to all stakeholders. The integration of software and hardware technologies that take advantage of a graphical environment will continue to improve both long-term and short-term mine design (Figure 1). A good design must be adaptive to respond to decision changes as the mine develops and more information becomes available. The constraints on mine design predicate careful analysis in order to operate the mine as efficiently and safely as possible.Continuous improvement in mining is assured by developing innovative technologies that target mine survey, drill and blast, modelling, short-term design and pit and stope optimisers. The design life of a mine has to be sufficiently long to ensure the mine is commercially successful, justifying the high start-up capital costs. Being able to execute a plan so that it honours the design realises the rewards of computerised mine planning and the long-term investment in data acquisition.

Sep 26, 2011

At Cliffs Natural Resources Ltd (CNR) crushing and shipping sample stations, precisions are estimated for the sampling, preparation and measurement stages of iron ore sampling in accordance with ISO 3085 (2002). In this Standard, gross duplicate samples are prepared at each of the three stages, yielding eight measurement assays. Appropriate calculations of the differences between assay pairs are then made to estimate precision of each stage of sampling. The International Standard for checking precision in iron ore sampling, ISO 3085 (2002) prescribes a method for identifying outliers that is ambiguous and possibly inappropriate. The procedure also makes an unnecessary implicit assumption, that the differences between assay pairs are normally distributed. The Anderson-Darling statistic is used to demonstrate that in some cases the assay pair differences have distributions significantly different from normal. When applied at CNR as specified, the Standard leads to precision estimates well below the expected values, thus overestimating the sampling method's capability and limiting the opportunity for real process improvement. This paper suggests an improved method of estimating sampling, preparation and measurement precision. A bootstrap procedure is used to estimate confidence limits for the calculated precision estimates. The proposed method would be suitable for testing blasthole precision. The discussion is supported by extensive simulation modelling of realistic data.

Mar 1, 2010

By Edmonds G. A

The power station went into operation in 1931, when the installed capacity was 12,500 kVA. with a loading of 4,000 kVA. In 1936 the loading increased to 6,750 kVA. which necessitated the addition of a third set which went into operation in 1937, the installed capacity at that date being 18,750 kvA. with a loading of 7,000 kVA. This remained fairly constant until 1945, when a gradual increase was noticed, the loading in 1952 being 10,598 kVA.With the addition of the copper plant, additional generating capacity was required and it was decided to raise the installed capacity by the addition of a fourth set to 34,375 kVA. with an expected loading, when producing copper, of 20,000 kViA.MAIN POWER PLANTThis consists of three GiE.e. alternators of 6,250 kVA. or 5,000 kW. at 0.8 P.F. rating and one G.E.C. alternator of 15,625 kVA. or 12,500 kW. at 0.8 P.F. rating, making a total generating capacity of 34,375 kVA.Each alternator is driven by Fraser and Chalmers turbines at 3,000 r.p.m.SYSTEMThe main 3 phase 3 wire 3,300 volt distribution system has the neutral point of alternators earthed through by one or two earthing resistors designed to limit earth fault current to 3,000 amp. for 20 seconds, in the case of the large machine, and to 1,100 amp. for 10 seconds, in the case of the smaller machines, or full load of either size machine at rated voltage.

Jan 1, 1953

Legislation introduced for Queensland and New South Wales Coal mines provides different levels of prescription regarding specification of mine seals û generally in relation to capacity to withstand overpressure. In Queensland, the Coal Mining Safety and Health Regulation (2001), Section 341 (d) places a further onus on the statutory ventilation officer to æensure all ventilation control devices at the mine are properly constructed and maintainedÆ and that the ventilation officer æmust ensure a ventilation control device mentioned in the regulation à and installed at the mine meets the design criteria statedÆ for the ætype of deviceÆ. Based on the experience of the author, it appears that risk management and life cycle approach to seals has not been adopted to the same extent as for other aspects of operations. Further, because of the number of disciplines and personnel involved that may influence various factors affecting seal integrity, the opportunity for oversight or unclear allocation of responsibility is considerable. While suppliers can provide explosion or design rated seals, this should only be a starting point for application of the product in a coal mine. Application is often considered by mine planning staff (taking into consideration mine environment parameters such as water, control of gas, spontaneous combustion risk, etc) in conjunction with the colliery ventilation officer, and then construction completed by contractors under supervision of operational staff. After construction, seals often are managed by operational personnel with input from the ventilation officer. Input of the geotechnical engineer into pillar design, roadway opening size, ground support specification and most stable seal location is also required. The need for a customised design approach for each seal site is proposed in order to take into account the many and variable factors that may influence a site so that improved seal performance reliability and predictability can be developed. A program of quantitative as well as qualitative monitoring of performance and triggers for rectification or maintenance action is required, and would provide support to the aforementioned proposal. Many mines rely on visual/audible inspection and periodic bag sampling as the primary means of assessment. Other significant factors such as seal material properties, rib degradation, convergence, floor heave, effects of water on both structural integrity of the seal as well as the air tightness of the seal do not generally receive the same level of attention. Based on the above observations, the author has compiled a reference checklist in regard to the above matters, including aspects of and approaches to mine and pillar design, geotechnical modelling and data collection, civil engineering design, site evaluation and practical options available.

Jan 1, 2005

By F M. Weir, M Fowler

The design of excavations in rock must, implicitly or explicitly take into consideration the influence of small- and large-scale geological structures. For most sites the complexity of a fractured rock mass is best captured using a 3D fracture system model based on field data. A discrete fracture network (DFN) approach involves stochastic modelling of the ‘smaller scale’, nondeterministic structures. For slope stability or tunnelling projects DFN modelling provides a valuable geotechnical tool for characterisation of a rock mass and identification of likely failure mechanisms.This paper presents a suite of the DFN modelling undertaken for the design of a large open pit in Australia. The proposed pit is to encounter a 160?m thick, high strength, sheared shale unit, which overlies a crystalline basement. DFN modelling was undertaken separately for both the shale and basement units. While the model inputs and development for each unit are briefly presented, the focus of this paper is on the various applications of the DFN modelling.A key advantage of the DFN approach for design studies is its probabilistic application to structural analyses and results. Multiple realisations of the same model were generated for both the shale and basement units, with the stability analysis carried out on each iteration. The generation of a large number of DFN models and analyses allow assessment of wedge volume, factor of safety and proportion of unstable slope for a range of conditions. The DFN modelling at the case study site was also utilised for a number of other purposes. For example, investigation of likely fault lengths in the shale unit and combined rock mass and defect failure. The development of this tool has been influential in improving our understanding of fracture networks for excavation design.CITATION:Weir, F M and Fowler, M, 2014. Rock mass characterisation and analysis for excavation design – a discrete fracture network approach, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 445–456 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014