Search Documents

By D J. Williams, S Islam

Fine-grained coal tailings slurry undergoes only limited settling and self-weight consolidation, and tends to remain slurry-like and unsuitable for conventional laboratory consolidation testing. In addition, constant rate of loading consolidation testing is more representative of the continuous disposal of tailings slurry into a tailings storage facility (TSF) than conventional step loading. The laboratory consolidation testing of coal tailings slurry under a constant rate of loading has been carried out in a purpose-built, large-scale, slurry consolidometer, instrumented with load cells and pore water pressure (PWP) transducers. In the slurry consolidometer, the rate of loading may be varied to represent the actual rate of rise of the tailings in the TSF. A slow rate of loading increases the test duration, while too fast a rate of loading may build up very high excess PWP, without achieving significant consolidation. For the particular fine-grained coal tailings slurry tested, the rate of loading in the slurry consolidometer is varied to access its effect on the development and dissipation of excess PWP. The resulting consolidation parameters are evaluated and explained using the recorded settlement and PWP data.CITATION:Islam, S and Williams, D J, 2018. Optimisation of constant rate of loading slurry consolidometer testing of fine-grained coal tailings, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 72–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By R Ahola, M D. Henschel, M A. McParland

With the introduction in recent years of third-generation interferometric synthetic aperture radar (InSAR) techniques, monitoring of mine slopes, benches and surrounding areas has benefitted from increased accuracy and coverage. Fundamental research into point and distributed scattering techniques has pushed the use of InSAR to provide higher spatial and height resolution. In this paper we discuss the operationalisation of third-generation InSAR techniques and show its application to active mining operations.This paper will discuss the use of multiple independent measurements of ground movement obtained from operationally-derived InSAR products over a wide variety of deformation areas within an active open pit mining operation (ie pit slopes, dewatering depressions, tailings containment and waste dumps). A technique that shortens the time between observations (increased observation frequency) and provides ongoing estimates of measurement accuracy will be described. The methodology exploits available satellite data by using multiple satellites and multiple beams. The paper will also examine factors in the design of a mine survey with third-generation InSAR and illustrate some of the necessary engineering trade-offs to efficiently monitor a mine from space.Overall, this paper aims to demonstrate the capabilities and advantages of operational third-generation InSAR techniques for ground movement monitoring of mining operations and provide a framework for proper design of a mine InSAR survey.CITATION:Henschel, M D, Sato, S, Ahola, R and McParland, M A, 2014. Designing interferometric synthetic aperture radar surveys for mine monitoring with accuracy assessment, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 233–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

concentrations) and physical nature of receiving streams, which in turn affects the stream ecosystem. Benthic macroinvertebrates are used to illustrate these impacts, and to investigate natural recovery in affected streams. In Charming Creek, a severely impacted stream in the Buller District, the macroinvertebrate community recovers diversity and the proportion of sensitive species (EPT) in the community is more significant with increasing downstream distance from the source of AMD. This is most likely due to dilution of AMD contaminated water by tributaries to the Charming Creek mainstream. Other impacted systems with less dilution from tributaries did not display similar levels of recovery. The effectiveness of remediation products BauxsolÖ and Zeolite was investigated using laboratory trials. Both products mitigated the toxicity of AMD and enhanced the survival of mayflies exposed to AMD contaminated water. Such products may be of use in the New Zealand environment but are likely to be most effective in conjunction with other systems (eg wetlands). Mitigating the impacts of AMD on stream ecosystems needs to include systems to directly address water chemistry issues (low pH, high metal concentrations) as a component of a holistic approach to restoring environmental conditions.

Jan 1, 2003

By R Goddard

An alternative stoping method has been adopted for narrow vein stoping at the Tasmania Mine in Northern Tasmania. Colloquially described as ‘Radial-in-Reef’ (RiR) stoping, the method employs the drilling of radial rings in the plane of the Reef from a drill stub located at the geographic centre of the proposed stope panel.Production from the Western Zone of the Tasmania Reef has been undertaken remotely from the Reef since 2007, after a detailed geotechnical engineering analysis indicated that the integrity of the sill drives could not guarantee an acceptable level of confidence should an anticipated seismic event occur within a radius of 10 m. The key tenet of the remote mining approach was the exclusion of personnel from sill drives once stoping had commenced. The remote mining method had to be ‘retrofitted’ to four existing stoping blocks totalling 11 sill drives which totalled 160 m vertically. The remote mining method proved to be complex, cumbersome and very expensive. However, the ore was extracted successfully.By early 2010, previously developed ore had largely been exhausted and the future development with an orebody open at depth presented the opportunity to review the current extraction method. However, the new extraction method needed to maintain the tenet of excluding personnel from sill drives of active stoping blocks, but seek opportunities to reduce the difficult and costly aspects of the previous method. The new ‘Radial-in-Reef’ stoping reduced the development requirement from six to two drives per ore block. Cost implications aside, the significant reduction in prestoping extraction ratio was expected to also reduce the likelihood of seismicity. Transverse production rings were designed to be drilled radially from a drill stub mined from a mid-stope footwall drive. Stopes totalling up to 7000 tonnes were planned be fired in a single electronic blast. Extraction was designed to take place from a basal sill drive under teleremote operation. At the time of writing, the method was under trial.

Mar 21, 2011

By C N. Hatton, K Ward

Tailings operations are inherently reactive as operations personnel continuously contend with a concentrator reject feed (tailings) transient in physical and engineering properties, which places a constant constraint on capital and operational spending. It requires a unique skill set to manage the prescribed distribution of tailings under unenviable conditions. Enter the tailings operator, an oftenundervalued commodity and untapped resource that can provide benefits beyond the rigors of dayto- day operational support. Experience consistently demonstrates that skilled and committed operators can serve a vital function in the safe construction of a tailings storage facility. It takes a village to raise a tailings dam. An important part of this process is establishing a culture of operational accountability and ownership. Operator development training is nothing new. However, we find that many of the intrinsic operator skills are left unexploited, and an operator's experiential knowledge base and creativity are commonly overlooked and underutilized. With proper training and guidance, these skills can be harnessed, contributing to safe dam operations. Operator engagement, when properly facilitated, provides tangible benefits ranging from improved tailings engineering properties to reduced closure costs. One important benefit is helping transitioning tailings management from reactive to proactive. There are many processes involved in the reactive to proactive transition process. One element of that process includes engaging operators in the tailings management process and facilitating legacy ownership. The core of operational legacy ownership is measured and described using five-stage operator engagement rubrics. Levels of operator engagement are presented with a description of the incremental benefits of each stage. An important part of legacy engagement is providing the tools to operators necessary for managing the tailings. Therefore, the approach identifies specific methods used by operations personnel to control tailings distribution and in-place properties. The end goal of leveraging operator engagement is to facilitate committed ownership and transition tailings management from an inefficient, reactive process to an improved, cost-effective, proactive practice.

Jul 1, 2021

By T M. Campos, H A. Petit, L M. Tavares, R Olympio

Much practical experience has been gathered in the last 30 years of application of high-pressure grinding rolls (HPGR) integrated with ball milling in size reduction of fine iron ore concentrates. The company Vale S.A, in Complexo de Tubarão (Brazil), was one of the pioneers applying the technology prior to pelletisation with an outstanding size reduction energy efficiency in the circuit and a significant increment in the specific surface area of the product. Recent studies by the authors demonstrated benefits of modelling and simulation to improve the performance of HPGRs in this particular application, with the model being able to describe HPGR performance under different operating conditions and under variations of feed size distribution. Despite these important advances, this modelling approach has only been used offline and under steady-state conditions. The present work applies the modified Torres and Casali model proposed by the authors in pseudodynamic simulations. The ability of the model to predict the characteristics of the product in real-time is evaluated using data available online for the pellet feed preparation circuit. Results demonstrated the model capabilities to map the physical operation and give a realistic representation of the process. Additionally, the model is demonstrated to be able to support the pellet feed production by providing extended real-time information of the process, making it a useful tool for improvement of the operational strategies and process stability.

Aug 24, 2022

By S Bright, M J. Masamvu, E K. Chiwandika, S Dandi, S M. Masuka

The depletion of high-grade hard and lumpy chrome ores has forced Zimbabwean ferrochrome producers to resort to low-grade friable ores that have an average of 28 per cent fines against a set limit of 12 per cent. Submerged open arc furnaces currently in use are associated with eruptions within the furnace because of the high amounts of fines, high energy consumption, as well as high SO2 and CO2 emissions. Traditionally employed agglomeration methods such as pelletising and the use of coke in the furnace have been discarded because of the pressure to lower operational costs and to achieve higher profit margins. This research aims to develop a method to incorporate lowgrade friable ore fines and unprocessed coal into production while lowering CO2 and SO2 emissions through a closed direct current (DC) arc furnace. The closed DC arc furnace could incorporate the friable ores and coal while maintaining above 90 per cent reduction rates. Preliminary findings also show that energy consumption could be reduced by up to 35 per cent by incorporating a pre-heating and pre-reduction system using the flue gases from the furnace. In the proposed circuit, the cost of production per ton of ferrochrome might be potentially lowered by an average of 30 per cent.

Jun 19, 2024

Contemporary approaches to safety management appear to be failing short of meeting its mark in improving mine safety. This is evidenced by the high workers compensation, high incidence rates and fatalities. Evidence from high-risk and complex organisations points towards safety culture as being important in improving site safety. In more recent years resilience engineering has been touted as a new and innovative way of managing safety. This paper reviews and synthesises previous literature on safety culture and resilience engineering. It then highlights methods that can be used to measure safety culture and resilience engineering, and explores similarities and differences between complex organisations and gold mining to identify opportunities for more innovative approaches to improving safety in gold mining operations through safety culture and resilience engineering.

Aug 1, 2010

By J Lea, P Hatherly, J L. Edwards

Coal exploration has traditionally involved the acquisition of data to enable a resource to be quantified and qualified to the extent that its economic potential can be determined. This process commonly relied on: drilling to determine the depth and thickness of coal seams, broad characterisation of the overburden and interburden, and to provide cores for coal quality analyses; basic wireline logging to cross-check the depth and thickness of coal seams and provide some indication of rock mass strength; and basic surface geophysics and remote sensing to identify major geological structures. In recent years, the adoption of the JORC Code as a basis for the reporting of resources and reserves has placed a greater emphasis on the need for detailed, reproducible data sets that not only satisfy the traditional requirements of mine planners, but also satisfy the governance requirements of corporate and financial institutions. Similarly, the development of sophisticated numerical modelling techniques for use in both open cut and underground mine design, has seen a greater demand for precise geotechnical data, in situ stress characterisation and hydrological information as routine input to the design process. These requirements, coupled with the prevailing trend toward high capital, relatively inflexible mining techniques less tolerant of geological surprises, and the need for consideration of environmental issues such as groundwater impacts and surface subsidence, requires that modern exploration programs be multifaceted, and designed to commence capturing data relevant to ædownstream issuesÆ even during the initial phases of exploration planning.

Jan 1, 2009

By O Handayani, R Barr, E Isaaks

The mining industry has focused a great deal of attention recently on the impact of blast movement on grade control. Although the problem of blast movement and its contribution to dilution and ore loss is well known, solutions to the problem are less than satisfactory. Perhaps the most recent innovation is the application of blast movement monitoring (BMM) devices to quantify blast movement. These devices emit an electronic signal and are planted at surveyed locations within the preblast material. Following the blast, their new locations are found using an electronic scanner. The magnitude and direction of the blast movement is given by the vectors between the pre- and post-blast BMM locations. However, it’s not clear how the BMM vector data can be best used to minimise dilution and ore loss. One common solution is to displace preblast dig line polygons by distances indicated by the BMM vectors. However, studies of BMM vectors show that blast movement not only displaces material laterally but also mixes material internally within the bench (Thornton, 2009a).This paper presents a method for modelling the post-blast muck pile that accounts for displacement and internal dilution using simulated annealing. The preblast ore control block model is re-blocked to 1?×?1?×?1?m sub-blocks. Each sub-block is displaced by simulated BMM vectors conditional to post-blast surface topography and blast initiation sequence data in addition to BMM vector data. The displaced sub-blocks are aggregated into new ore control model blocks whose grades are calculated from the contained sub-blocks. New dig lines are then designed on the post-blast muck pile model using the new ore control block model grades. A case study based on actual data is provided.CITATION:Isaaks, E, Barr, R and Handayani, O, 2014. Modelling blast movement for grade control, in Proceedings Ninth International Mining Geology Conference 2014 , pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By W J. Rankin, D R. Swinbourne

There are large tonnages of low-grade manganese ores in India fromwhich it is uneconomic to produce ferroalloys by conventionalsubmerged arc furnace smelting. A possible way to utilise these ores is to smelt them with carbon to produce pig iron and a manganese-rich slag, then to metallothermically reduce the molten slag to silicomanganese. Thermodynamic modelling of the metallothermic reduction stage using aluminium, silicon or aluminium-silicon alloy as the reductant at 1450¦C showed that an acceptable grade of silicomanganese could be produced. Manganese recoveries were predicted to be about 80 per cent. Heat balances indicated that silicothermic reduction may not produce enough heat to maintain reaction temperature. Small-scale laboratory experiments showed that the manganese grade of the alloys, and the manganese recoveries, were close to those predicted, but those for silicon were muchlower. Aluminothermic reduction produced the highest grade manganesealloy. The slag-metal equilibrium involving manganese, silicon and their oxides was investigated and it was found that equilibrium was not attained in any of the experiments, due probably to the very low rate of reactions involving silicon. This could be used to advantage in practice to achieve higher manganese levels in the alloys.

Jan 1, 1998

This paper describes the past, normal and advanced practice of optimisation in mining. It then discusses what needs to happen for the mining industry to make full use of what is now available.

Dec 6, 2010

By M Behrens

The Melbourne Main Sewer Replacement (MMSR) is a major urban infrastructure project involving approximately 2.3 km of tunnelling and construction works. The works extend from Docklands Precinct, on the southwest edge of the city, southwards to connect with the Hobsons Bay Main Sewer in Port Melbourne. The tunnel boring machine (TBM) tunnelled section of the works terminates at the Yarra River where the delta geology and alignment requirements precluded the use of underground tunnelling methods. The 132 m long river crossing works involve a cut-and-cover excavation within a staged fl ooded cofferdam construction to construct an immersed tube tunnel as an extension of the TBM works.This paper reports on the development of the staged construction method and highlights the geotechnical and structural design aspects involved in building a new sewer in the Yarra River to close the gap between the new TBM driven and pipe-jacked tunnels.

Mar 8, 2011

By R L. Brathwaite

The orogenic gold deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Orogenic gold deposits are typically quartz vein deposits formed in fault and shear systems at crustal levels within and above the brittle ductile transition zone, at depths of 3 12 km and temperatures from 200¦ to 400¦C. In New Zealand, orogenic gold deposits are found in regionally metamorphosed sedimentary rocks of Paleozoic and Mesozoic age. The deposits in Paleozoic rocks include those at Golden Blocks in Northwest Nelson, Lyell and Reefton on the West Coast, and Preservation Inlet in Fiordland. Quartz veins are developed along shear zones that dip steeply and generally strike parallel to the axes of folding in the greywacke and argillite/slate host rocks, although most are discordant to bedding. The lodes are typically less than 1 m wide and extend an average 200 m horizontally and vertically, but the Birthday Reef at Blackwater, Reefton, the largest quartz vein deposit in Paleozoic rocks, averages 60 cm in width and was mined over a strike length of 1070 m, and to a depth of 830 m. Disseminated gold occurs adjacent to the quartz lodes at Globe-Progress and some other Reefton deposits. The deposits in Mesozoic rocks are hosted in schist of Otago and Marlborough, and schist and greywacke of the Southern Alps. The lodes are typically lensoidal, less than 1 m wide and localised along single or multiple parallel shear zones that generally dip steeply, and are discordant to the schist foliation and bedding. A notable exception is Macraes, where the lodes are developed in the semi-concordant, low angle Hyde Macraes Shear Zone that has a strike length greater than 25 km.

Jan 1, 2005

By May J. R

Exploration, including research, has fuelled the enormous expansion of the Australian mineral industry in the last three decades. Analysis of success and failure in exploration and research has therefore potentially powerful lessons and messages which may be used to influence the future shape and direction of the mineral industry. Research has been an integral part of organised corporate mineral exploration since its beginnings in Australia in the 1930s. In corporations, the activity generally called project generation or new project development is the main expression of exploration research but mostly it goes unidentified and poorly documented except perhaps when a successful discovery is made and reported on. The competitive nature of exploration means that extended and detailed analysis of corporate exploration research across the industry is impossible to achieve.

Jan 1, 1992

Any hypothesis for the origin of the Otago gold-quartz lodes must account for the following observations. 1. Southeast of Glenorchy, where the schists hosting the lodes are comparatively unaffected by Neogene Alpine Fault deformation, the dominant strike of the vein systems is NW-SE, parallel to the axis of greatest post-metamorphic uplift in the Otago Schist belt (Paterson, 1986). 2. The lodes are fault-hosted, with some developed along steep, low-displacement normal faults (eg Barewood, Bendigo, Nenthorn), implying NE-SW extension, and some developed along low-angle thrusts (eg Macraes) implying, in apparent contradiction, NE-SW contraction (Teagle et al, 1990). 3. The mineralising fluid was of metamorphic origin (McKeag and Craw, 1989), but while some of the lodes developed in a mesothermal environment at considerable depth (eg ~10 km for Macraes), others appear to have formed at very shallow depth (eg <1 km for Nenthorn) (Craw and Norris, 1988). 4. The timing of the mineralisation is generally poorly constrained but postdates the main Rangitata schist metamorphism. It probably initiated during early Cretaceous exhumation and unroofing of the schist belt (140 - 120 Ma?) and may have continued well into the Tertiary (Craw, 1989). Estimates for the relative ages of the different lodes are largely speculative but, based on pressure estimates from fluid inclusion studies, Macraes likely represents the deepest and oldest lode system while Nenthorn (just 12 km to the southwest) is perhaps the shallowest and youngest (Craw and Norris, 1988).

Jan 1, 1992

It should be stating the æbleeding obviousÆ to say that the most efficient method of recovery must be used during the testing and evaluation phases of an orebody. Furthermore, the company will be literally throwing away money by not using the most efficient recovery plant during mining. This is especially true in the case of a low concentration/high value commodity such as diamonds. Unfortunately, this economic recovery criterion is not always the driving force. Some inexperienced companies think that they can preserve capital by using cheaper, and generally less efficient, recovery plants to mine their product. This philosophy is invariably a fallacy. Furthermore, it is also important to use the correct sized plant for the proposed task. It is no use trying to use a small testing plant to treat large quantities of ore, as this may result in loss of recovery efficiency. The converse is equally true.

Jan 1, 2004

By E J. Hill, F Huang, A Otto

Geochemical data from drill core samples is used in mineral exploration to enable geologists to understand subsurface geology. However, it is challenging to analyse these data sets rigorously and consistently. Manual data interpretation relies on the knowledge and experience of logging geologists. When multiple geologists are involved, it is possible to introduce inconsistencies in logged lithology type and scale of logging (‘splitters’ versus ‘lumpers’). Machine learning (ML) is a powerful tool for analysing high dimensional data (ie data with many variables) and large data sets (ie data with many samples). However, ML methods applied to drill hole samples do not incorporate spatial information and this can result in high misclassification rates and small-scale ‘noisy’ results. We demonstrate the use of multiscale spatial analysis (wavelet tessellation) as a pre-ML step to analyse spatial information. This step helps reduce misclassification and filter out unwanted small-scale variation in the data. In an experiment, we used wavelet tessellation and supervised ML to predict litho-geochemical rock types from geochemistry data. The data set is from the Valhalla uranium deposit near Mount Isa, northern Queensland. First, geochemical knowledge and statistical analysis was used to select appropriate geochemical elements for litho-geochemical classification. Second, the elements were processed using multiscale spatial analysis. Third, we trained a Random Forest model with the data set and found that the model performs worse in predicting rare rock samples than common ones. We applied over-sampling and down-sampling methods in aim to overcome this issue. As a conclusion, the combination of multiscale spatial analysis (to define rock unit boundaries) and Random Forests (to classify rock units) is a good method for rapid and accurate analysis of drill hole geochemistry.

Mar 22, 2022

By A Hutton, C Dick, D Fletcher

Mine and facility closure planning is a dynamic and rapidly evolving landscape. In this landscape, mining companies and industry consultants are generally good at estimating the associated earthworks and rehabilitation costs, because it is æcore businessÆ. Through our extensive work in mine closure, we have found that the safe and cost-effective demolition of mining related infrastructure is often grossly underestimated. Or alternately, it is simply assumed that the returns on scrap steel and the sale of re-usable plant will cover the related costs. With fluctuating steel prices and no guaranteed buyer for the assets, the estimated monetary return is often unreliable and in many cases unrealistic. On this basis this logic is fundamentally flawed. We have found that on most occasions this has meant that closure cost estimates fall well short of what the actual costs are to close the mine.GSSE and Liberty Industrial have worked on over 60 mine closure projects in Australia and overseas of varying scales and across a range of commodity types. An evaluation of these projects has shown that costs associated with the safe demolition and removal of a mining related infrastructure is in the order of 20 - 30 per cent of the total cost at closure. We believe it is one of the top three risk areas associated with mine closure planning and cost estimation, alongside bulk earthworks and the capping of tailings and waste rock storage facilities.Our paper uses examples from recent projects to demonstrate all aspects outlined above. We have also endeavoured to address the following key points related to the demolition and removal of mining related infrastructure:If companies fail to plan appropriately, complicating factors such as contamination, hazardous materials, mobilisation/demobilisation, geographical location, decommissioning standards, site constraints and weather, can add considerable costs to the project and result in variations for the demolition contractor.Closure planning often assumes infrastructure that is no longer required can be utilised by a third party and/or the new land holder. We intend to show that unless adequate consultation and planning is undertaken, this is not beneficial to the mining company, the environment, or the local community.CITATION:Fletcher, D, Hutton, A and Dick, C, 2012. The æsmoking gunÆ of detailed mine closure cost over-run - A review using case studies of the real costs associated with the demolition and removal of infrastructure in mine closure, in Proceedings Life-of-Mine 2012 , pp 325-332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By R Garzon

For resources projects with healthy net present value (NPV) and low cash flow volatility, conventional discounted cash flow (DCF) analysis will continue to provide the dominant investment decision-making criteria. However, DCF analysis can be biased because it often applies a single risk-adjusted discount rate (RADR) to compare the value of projects with different risk characteristics. Many of the difficulties with DCF modelling arise from analystsÆ inability to determine appropriate risk discounts and to estimate expected spot prices inputs for the commodities produced over the life of the project. Modern asset pricing (MAP) is a very valuable complement to DCF analysis in addressing some of these issues. Most papers dealing with MAP, however, while academically rigorous, tend not to be explicit in terms of practical application of this methodology in routine project evaluation. This paper has the objective of reviewing the MAP methodology and of demystifying its complexity, by providing a simple but realistic step-by-step evaluation of a mining project, comparing its DCF and MAP NPV values. The paper concludes that MAP provides a minimum, risk-adjusted æfloorÆ value, thus representing a valuable complement to any DCF valuation.

Jan 1, 2007