Search Documents

The status of remote sensing data availability in New Zealand is outlined and discussed. Currently, two multispectral remote sensing satellites are providing regular data over New Zealand; aircraft scanner services are available from Australia.; operational radar satellite services are yet to materialise. The advantages and disadvantages of the various data types are compared and contrasted. Some image processing considerations are outlined.

Jan 1, 1993

By M Vendrup, T C. Christensen, C Dube

The adsorptive and granulate forming MetClean™ process has been used at many locations in Northern Sweden, Norway, Denmark, France, Spain, Mongolia, Japan and Australia. It has been pilot tested and used in full scale treatment plants to remove metals from:mine watersleachate from solid waste in incineration flue gasleachate from fly ash damsleachate from landfill and waste ponds.The following paper provides details of pilot and plants tests on the effectiveness of MetClean™ in removing arsenic, antimony, barium, cadmium, copper, molybdenum, nickel, radium, uranium, vanadium and zinc. Results show that MetClean™ may reduce the concentration of these metals in treated effluent water to the one part per billion (ppb) range.The paper also finds that, for specific metals, the optimal adsorption condition depends on the:pH levelmolar relation between the specific targeted metal and the addition of iron (II) or manganese (II)type of oxidation agentssalinity levelpresence of other metals.The most effective pH level varies according to the targeted metal but falls within the pH 5 to pH 11 range. A compromise pH level may be set when more than one metal is targeted for removal at the same time and through only one process step. The removal efficiency of one or both metals may be affected by operating at a compromise rather than optimum pH level.The MetClean process generates non-hazardous solid waste. Waste can then be disposed of more easily than brine or sludge.CITATION:Christensen, T C, Vendrup, M and Dube, C, 2015. Pilot tests for heavy metals removal in mine water, in Proceedings MetPlant 2015, pp 404–415 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Pati±o A

The Argentine pyroclastic loess arevulcanogenic deposits, which have their sources in the circumnpacific rim. The object of this work is to realize a de-tailed mineralogical characterization of this sediments, to use it like a geo logic outline which regiters discordance or similarity in them, The sampling zone extend from 714N-4125 to 622W-339S. The descriptions of these sediments was considered like basic, mesobasic or acid rocks. The basic sediments, looking like andesite-basaltic composition, are fill-ing the andean valley. The mesobasic one have a similar composition with a pyro-clastic dacite rock, and have been found in marshy pleistocene sediments in the intermountain valley and in the pampeana prairies. The acid ashed conform rhyoda-cite-rhyolite sediments which form the pampeana loess covers in the prairie.

Jan 1, 1990

By A Singh, C Da Corte

Banded Iron Formations or more commonly known as BIF are sedimentary rock formations with alternating silica-rich layers and iron-rich layers that are typically composed of iron oxides (hematite and magnetite), iron-rich carbonates, and/or iron-rich silicates. Considering the depletion of highgrade iron ore reserves in South Africa, there is a need to maximise resource utilisation through the exploitation of sterile resources in particular BIF material which makes up greater than 65 per cent of current reserves. BIF, like most resources, is non-renewable and the deposition of BIF is thought to have come about by the reaction of Fe2+ ions in the ocean water with dissolved oxygen billions of years ago. BIF ore derived from the Limpopo region in South Africa (SA) located in the Penge Iron Formation is according to Cairncross, Kramers and Villa (2018) equivalent to that contained within the Asbestos Hills Iron Formation of the Transvaal Supergroup in the Northern Cape, SA. Considering that these are one of the largest iron ore deposits in SA, the case study involved mineralogical characterisation followed by beneficiation of BIF from these two regions to ascertain the comparability. Coarse and fines gravity separation comprising of Heavy Liquid Separation/Dense Media Separation on the +1.18 mm size fraction and shaking table on the -1.18 mm size fraction was conducted to ascertain whether an on-grade product or blended feedstock could be produced. The Limpopo mixed and Northern Cape conglomerate BIF samples achieved similar overall responses due to the conglomerate sample containing 15.3 per cent additional -1.18 mm fines. A combined coarse and fines product grading at 60 per cent Fe could be achieved at a yield and recovery of 43.9– 53.0 per cent and 62.2–63.8 per cent respectively. Increasing the grade to 63 per cent Fe reduces the overall recovery by 13.3 per cent. At the higher target grade, the contaminant specifications could be achieved for both samples. The Northern Cape laminated BIF sample is the most promising of the three samples studied. At the two iron target grades overall yields and iron recoveries of 72.9–65.4 per cent and 85.2– 80.2 per cent was achieved. In both instances the silica grade exceeded the product specification, however if the silica content is the driver the target iron grade should increase to 63.32 per cent. This will result in a minimal decrease in recovery of 0.4 per cent. The promising results of this study indicate that coarse beneficiation of BIF material is possible. These ore types could be blended with superior grade products to improve overall yields and recoveries or sold directly at a 63 per cent Fe product grade whilst sacrificing 0.4–13.3 per cent recovery.

Nov 8, 2021

Effect of Spacer Chain Length on the Flotation of Kaolinite and Quartz by Using Gemini Surfactants as Collector

Sep 13, 2010

By G N. Phillips

Global annual gold production has been remarkably constant over the last decade at ~2500 t/a3. The major producers today are China (annual production over 350 t and rising), Australia (250 t), USA (240 t), Russia (200 t) and South Africa (190 t and falling); these figures are representative of recent years but approximate. Demand from jewellery, investment, industrial and dental uses has been in excess of mine production for the last decade, by approximately 1000 t/a.Ongoing exploration is the life-blood for gold mining, and more so than for many other metals. Explorers consider sovereign risk, security, labour costs, commercial terms, land availability and inherent geologic prospectivity to determine where to focus their activities. Exploration success over the last decade has been shared by established major producers like Australia, Canada and USA, several countries in West Africa, and many parts of the Pacific margin. Although gold-only deposits have dominated world gold production historically, the gold-plus types, especially copper-gold, are becoming more important.Australia experienced a major period of exploration success from 1979 that has led to annual gold production rising from 17 t in 1979 to 250 - 300 t/a recently. Today, Australia has economic demonstrated resources of over 9000 t Au, which has risen progressively from 220 t in 1979. The majority of production has come from gold-only deposits in the Yilgarn craton in the southern half of Western Australia, but there are a few large Proterozoic deposits in central Australia including Olympic Dam, Telfer and Starra, which are mostly gold-plus types with copper and gold. Large goldfields in the younger host rocks of eastern Australia include the gold-only deposits of Victoria and North Queensland, and gold-plus deposits of New South Wales.CITATION:Phillips, G N, 2013. Australian and global setting for gold in 2013, in Proceedings World Gold 2013 , pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

In Broken Hill, Northern Rhodesia, two water jacket lead furnaces have been in operation for the past three years. The furnaces were erected in war time, and only absolute essentials were procurable. The water for the jackets was obtained from wells adjacent to the works, in a dolomite formation. There being no water-softening plant, except a small one capable of treating water for the power plant only, this water was found to make a heavy scale in the jacket. During 1917 several jackets were burnt through, resulting in serious trouble and loss of output. In order to avoid this, furnaces were stopped twice a month for 8 hours and scale was removed as far as possible. In addition to the scale trouble during the summer months, a green slime grew in the supply tanks and occasionally became detached from the tank and collected in the cocks near the jackets. This caused risk to the jackets and was difficult to remove without a stoppage of the furnace. In 1918, bundles of wattle bark were placed in the hot well at the rate of one ton per month. These extracted the tannin and added from 0.5 to one part of tannin per 100,000 to the circulating water. The hot water was cooled over a brushwood cooling tower and returned to the supply tanks. The well water required to, make up the wastage was estimated at 40,000 gal per day.

Jan 1, 1920

On the first of October 1991 two significant pieces of legislation came into force. Both of these are relevant to the allocation and use of minerals in New Zealand . They are the Crown Minerals Act 1991 and the Resource Management Act 1991.   The full legal implications of these is not fully known because the Planning Tribunal and the superior courts have not as yet had to deal with them in any detail. However, the thrust of the legislation is clear and it is appropriate to give an overview of how the statutes will operate in tandem if you are seeking to pursue or oppose any prospect, exploration or mining of Crown Minerals in New Zealand.

Jan 1, 1992

Jan 1, 2004

By P Thwaites

The mining industry uses many types of mineral and metallurgical plants to produce saleable product from ore mined. Plant design history has left current operations with a mixture of manual operation and various forms of automated process controls. Consequently, we typically see high-variability in the continuous operations together with a shortfall in the attainment of full capacity or higher utilisation of consumables.At a level of best practice, ‘operational performance excellence’ focuses on process control, using automation and control systems to deliver process optimisation. This more sophisticated delivery is a great deal more difficult than the first stage of equipment selection/installation. It includes the appropriate selection of the right instrumentation and control system, key process knowledge, individuals with a solid control engineering background/experience and the essential backing/support of the operations management team together leading to higher-value delivery. Robust solutions can be realised, considerably minimising process variation, thus leading to process optimisation. This approach results in an easier, efficient and safer process while providing considerable returns for the plant owners.How variable are your processes, and do you maintain optimised process performance with dedicated resources, modern instrumentation, ‘best practice’ control systems and performance monitoring tools? In this paper, these questions and their possible answers are discussed.I say we can do much more and be ‘more efficient’ in our efforts to remain competitive. This area remains a major opportunity for improved efficiency, minimising tailings losses and other milling costs.CITATION:Thwaites, P, 2014. Manual control, process automation or operational performance excellence – what is the difference?, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 13–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Mutmansky J. M, Hartman H. L

Multiple operating points for mine fans are a problem that fan and mining engineers must constantly be aware of in mine/fan systems. In a single-fan system, unstable conditions can be avoided by restricting fan operation to the "normal operating range." When mine fans are operated in parallel, the situation becomes a little more complicated. Multiple operating points are more often encountered and the fan user must be aware of these multiple points to have a suitable set of operating conditions. However, for fans in parallel, the engineer can plot the combined characteristic in a relatively straightforward manner and thus can avoid conditions that would cause instability in the mine/fan system.

Jan 1, 1988

By C McCracken, R Landers, B Hesse

Minnovare identified the potential to improve production drilling outcomes in underground long-hole stopes through the adaptation of new technology which was under ongoing development. An approach to Evolution Mining resulted in the companies agreeing to a collaborative agreement to further develop the technology for use on underground long-hole drilling equipment. During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing setup/alignment process was compared to the new technology system with the following observations: • Using the existing process only 20% of holes surveyed recorded toe points within the +/ 300mm (11.8in) tolerance blast-hole deviation. • The new technology was proven to limit rig setup/alignment error, reducing average blasthole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: • Stopes drilled using the new technology recorded 62.6% less average dilution. • This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). • With the system implemented as standard practice following results of the FY18 trial and continued success, overall dilution for full year FY19 showed continued reduction to 12% Evolution has continued use of the new technology at Cracow, where the improved accuracy has allowed the extraction of narrower stopes where drilling accuracy is critical. Evolution has also deployed the technology at the Mungari operation and has stipulated that the contractor use the technology at the Mt Carlton operation, which is currently under development. Future implementation of the Development Optimiser system should be verified by commencing additional trials to include a larger data base for validating the initial trial results.

Mar 15, 2021

By M J. Thurley, M Wimmer

To assess the present-day functionality of large-scale sublevel caving at LKAB Kiruna a comprehensive measurement program was undertaken involving blast function, fragmentation and gravity flow. As part of this assessment, a fragmentation measurement trial was performed based on 3D imaging of the drawpoint and corresponding bucket load of the underground load-haul-dump (LHD) excavator. 3D image data from stereo photogrammetry was collected and an automated image analysis strategy developed. A number of data sets were collected for each of the drawpoint and LHD bucket, along with sieving results for four of the LHD bucket loads (totally about 70 t). Two of the sieving results were used to inform the automated image analysis strategy, and two were held back as a comparison. Large variations in the visible particles are apparent when comparing corresponding drawpoints and LHD buckets highlighting the impact of sampling location and the need to measure large quantities of data in order to avoid bias from small samples. The results show that 3D imaging and analysis can produce fully automated measurement and analysis of the visible particle size distribution. Although this is not the same as the sieve-size distribution it provides useful estimation of both the larger size classes and a bulk estimate of fine material below approximately 60 mm. The 3D stereo photogrammetry measurement system used produced very high 3D point density but this was achieved using a custom up-sampling technique which significantly smoothed the data, removing small particles, smoothing edges, and this negatively affected the particle delineation algorithms.CITATION:Thurley, M J, Wimmer, M and Nordqvist, A, 2015. Blast fragmentation measurement based on three-dimensional imaging in sublevel caving drawpoints and underground excavator buckets at LKAB Kiruna, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 763–774 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A L. Welsh, P S. Newling

Mill operators are entrusted to manage what are normally the largest capital assets on any mine site. Achieving maximum utilisation and lowest costs that drive operating margins are realised by applying well known fundamentals of good housekeeping and proactive (as opposed to reactive) maintenance programmes. Historically, maintenance and operations staff are bought in late during the construction stage and often do not have the time, know how or tools to put in place (let alone train the incumbent staff) a functioning maintenance system before commissioning starts. They then get drawn into a reactive maintenance paradigm as teething problems post commissioning are dealt with and day to day issues envelop the line tradesmen and supervisors. Additionally, even when some semblance of a planned maintenance system is established, it is often the case that over time personnel and cultural issues mask the development of problematic maintenance practices. As has been observed by the authors on many occasions, even when some basic programmed maintenance system is in place, the collection of maintenance data is often inaccurate, incomplete and not subject to analysis. The net result is of course a high incidence of machine failure leading to lower than expected availability, which ultimately translates to lower revenue and higher net maintenance costs. The time taken and the cost to repair a failed machine is always greater than the timely and planned repair of a worn machine.Upon review of a number of processing plants around the world, especially gold and small base metal operations, it is apparent that companies need to implement maintenance systems whereby the operators are not overwhelmed with data and can manage by exception. Inadequate or inaccurate data collection and analysis result in poor decisions being made and misguided actions taken. GR Engineering Services (GRES) has developed a system to enable the custodians of mining plant assets to make more effective and effective use of maintenance data by being able to focus on the indicators of plant deterioration and to programme concurrent maintenance activities to maximise plant availability and utilisation.This paper outlines the structures that can be employed to address the challenges of implementing a proactive asset management system. The best practice strategies described herein have been based on the fundamentals of a sound asset management framework:a phased approach to the development of Asset Management methodology and processeseffective implementation of programmed maintenance routinesmanaging asset condition data collected from various sourcesefficient analysis of asset data and management by exceptioninterfacing asset management data with Computerised Maintenance Management System (CMMS) and Electronic Management Systems (EMS) systemstips to assist with maximising asset performance.CITATION:Welsh, A L and Newling, P S, 2015. Operating strategies for custodians of company assets creating wealth, in Proceedings MetPlant 2015, pp 338–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By M Orunesu Preiata

The Odysseus Project is part of the high-grade Cosmos Nickel Complex that lies 30 km north of Leinster. The Odysseus definitive feasibility study (DFS) was approved by the Western Areas’ board in October 2018. Early works commenced in January 2019 with rehabilitation of the existing underground infrastructure. In June 2022 Western Areas was acquired by IGO Ltd. The project is now well advanced to meet its target of first concentrate. The project included the construction of a haulage shaft. The design of the hoisting equipment and the shaft barrel evolved from the initial DFS design stage to the final execution, as the data were made available from the initial investigation to the data gathered during execution (although this did not change from its initial concept). The design philosophy for the haulage shaft incorporated, from the beginning a multidisciplinary approach with inputs from three main areas involved in such projects, namely excavation techniques, geotechnical assessments, and infrastructure construction. This interaction is a fundamental component for the success of such a critical project. In fact, each of these three areas influences each other in a cyclical manner, triggering a continuous review of the project inputs and outputs, while maintaining the original project goals: the design of an infrastructure able to deliver the desired throughput. The throughput dictates the infrastructure that needs to be built, which in turn controls the size of the shaft. The key assumption applied to this is that the rock mass can accommodate the excavation void, and the excavation technique with its tolerances and limits that ultimately need to be verified back with the initial assumptions used for the infrastructure design. The aim of the paper is to present a case study of the experience gained with the Odysseus hoisting shaft and to propose a possible logic path for similar projects elsewhere.

Mar 29, 2023

By R M. Briggs

Kapowai Caldera Complex (KCC), located 10 km west of Tairua (eastern Coromandel Peninsula), is a late Miocene composite collapse caldera, formed during eruption of several small and large volume andesitic rhyolitic ignimbrites. Numerous epithermal Au-Ag mineral deposits and associated alteration zones at the KCC are related to caldera (rhyolite lava domes, intracaldera faults) or regional structures (faults). The main epithermal deposit exposed in the central KCC is associated with an E-W striking structural boundary fault that cuts the Welcome Jack rhyolite dome. Propylitic (calcite - chlorite) and sericitic (quartz - sericite) alteration haloes surround this deposit. Sporadic zones of sericitic alteration are also exposed within and on the margins of the Bulls Run rhyolite dome complex. Epithermal systems post-dated emplacement of these rhyolite domes, but were controlled by them. Propylitic alteration of ignimbrite in the floor of the Kapowai and Kauaeranga valleys is related to the major NE-trending Kapowai Fault which extends SW to south of Thames. Alteration along this fault pre-dates alteration associated with the rhyolite lava domes. Numerous sericitic and propylitic altered welded ignimbrite, rhyolite and andesite lava lithic fragments have been sampled from intracaldera ignimbrites, and although no direct source is known, they infer the presence of buried epithermal systems. Repeated epithermal activity at the KCC is inferred by the exposed epithermal deposits/alteration zones and the older buried geothermal systems. Silicic caldera volcanoes are considered to be critical volcanic environments for epithermal Au-Ag mineralisation in Coromandel, but are highly variable and need detailed stratigraphic, structural, petrologic, and geophysical studies to characterise them.

Jan 1, 1999

By R WOODS

The interaction of, flotation collectors with sulphide mmerals takes place at the solid-solution interface. The electrochemistry of the processes which affect this interface are discussed. The interaction of xanthates with sulphides is an electrochemical process, xanthates being electro-oxidized to chemisorbed xanthate and dixanthogen.The role of oxygen is to provide a cathodic process to allow the anodic oxidation to occur. The hydrophobic condition of the mineral surface is brought about by the presence of the oxidized xanthate species. The action of reagents which can activate or depress the flotation of sulphides is discussed briefly.

Jan 1, 1972

By A H. Gray

Gekko Systems Pty Ltd engaged in the test work, design, manufacturing and commissioning of the pre-concentration plant at Silver Standard Resources Inc’s Pirquitas mine in the north western Jujuy province of Argentina. Testing of the ore at coarse feeds of between 2 and 12mm returned probable recoveries of up to a total of 95% silver into 50% of the mass fed to the InLine Pressure Jigs (IPJ’s). The plant has been designed and built based on the test results to include a preparation screen to bypass the fines that are naturally higher in grade and repulping of the coarse which is then pumped to three parallel trains of 2-stage IPJ roughing-scavenging. The target 50% yield to concentrate passes over a dewatering screen and the solids are returned back to the mill feed conveyor. The IPJ tails are transferred to a dewatering screen and solid rejects are stockpiled off the end of a transfer conveyor. All dewatered underflow products are processed via hydrocyclones to recover dirty water for use back into the IPJ circuit and return entrained fines to the fines bypass line.With the sulphide orebody being processed, the results from operations to date have shown that plant performance is matching the original laboratory sulphide ore testwork data. The objective of the pre-concentration step is to both reject gangue and achieve grades between 300-400g/t Ag to the float circuit as flotation recoveries are maximised within this range. The plant currently achieves overall upgrades of approximately 150% of feed grade with the IPJ only circuit producing an average 180% increase from calculated feed grade.

Aug 8, 2011

Since the last occasion on which I spoke to you on this subject there has been a considerable increase in the mechanical ventilation of Western Australian mines.The following table compares the figures for 1939 with those of 1941. The type of fan most commonly used is the limit load fan. On account of its higher mechanical efficiency it has very largely superseded the multivane fan with forward curved blades.Two fans of the propeller type are in use and these have given very satisfactory service. This type of fan also has a high mechanical efficiency particularly at the correct duty for maximum efficiency.The maximum efficiencies obtainable from the various types are, for "multivane" 670/0, for "limit load" 75%, and' for aerovane 7810/0.References to propeller fans with variable pitch have appeared in the technical press, but no detailed d~scription has been issued. The advantages of these fans for mine ventilation are not obvious. An aeroplane is required to operate over a wide range of duties, while the speed of the motor for maximum efficiency is pl'actically constant. In such circumstances the propeller can be adapted to the particular work it has to do by varying the pitch of the blades. In a mine the speed of the fan can be varied to suit.the conditions, and it would appear that variable pitch is not necessary while there is a reasonable range of fans to choose from.The question of the correct position for the fan still comes in for considerable discussion. Exhausting fans at the surface have the support of time and custom, and in many cases this represents the only reasonable arrangement. Such fans should be fitted with an evase, especially in the case of fans with a high outlet velocity such as the aerovane types.It is claimed that there are advantages in having the fan at the surface where it is readily available for inspection and maintenance. Experience has shown that these advantages are more apparent than real. Fans will run for long periods with no attention other than occasional greasing and cleaning, and modern electric motors will run without attention for very long periods.In some instances the expense of a power cable to take current to the fan may be saved by placing it on the surface, but in the majority of cases...

Jan 1, 1941

By S Taylor, B Lumsden, G Long

Statistical metallurgical plant trials are becoming more widespread, as a valuable tool for increasing plant profitability. Generally, a single parameter like metal recovery varies under the trial condition while all other variables such as average metal feed grade or average metal concentrate grade are equal for the two test conditions during the period of the test. Metal recovery is usually the measured variable because concentrate grade is fixed by smelter terms, and plants operate to maximise recovery at the required concentrate grade. However, in all flotation plants there is a relationship between concentrate grade and metal recovery, and under the same conditions increasing one results in a decrease in the other. At MMGÆs Rosebery Mine the zinc concentrate produced is generally above smelter specifications, so zinc concentrate grade can vary during a test. During trialling of magnetic conditioning in the Rosebery zinc circuit, the difference in both zinc recovery and zinc concentrate grade were analysed. The analysis of changes in zinc grade and recovery during the trial raised some interesting questions about the relationship between concentrate grade and recovery. A paired statistical method was developed and tested to combine in each pair the change in concentrate grade and recovery in a single result that could be analysed by a paired t test. This method was found to be very sensitive to combined, varying changes in concentrate grade and/or metal recovery. It was also evaluated on plant test results from another flotation plant to verify its applicability in other plants. CITATION:Long, G, Taylor, S and Lumsden, B, 2012. Statistical plant trials - Efficiently combining concentrate grade and metal recovery results, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 355-362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012