Search Documents

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table 1 may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of an 0 is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true

Jan 1, 1940

By T. B. Brooks

THE iron ores of the Marquette region are mostly extracted in open excavations ; hence the process is more properly quarrying. Several attempts at underground work have been made, which have not, on the whole, been successful. The Edwards mine has been almost entirely wrought by candle-light. The slate ore pit, No. 1, of the New England mine, is now worked in the same way, as is also the Pioneer furnace pit of the Jackson mine. The Champion mine was opened systematically for underground work, with two levels, 60 feet apart, and three shafts at distances apart along the bed. of 200 feet; but this idea has been practically abandoned, the greater part of the ore in that mine being now taken out in open pits. Several other mines have occasionally worked underground stopes, but only temporarily; if such stopes could not be opened out to day-light, they have usually been abandoned. In brief, it may be said that no considerable amount of ore has as yet (1870).been extracted underground in the region, and of that so mined very little has been taken out at a profit; and I may add that it seems to be the belief of the most experienced mining men that this state of things will hold for some time to come for reasons which will appear. Nearly the same remarks may be applied to the mines of the Iron Mountain region, Missouri, the ores of which are very similar in character to those of Marquette. Some of the New York and New Jersey magnetic deposits are wrought open, but this is the exception, underground mining there being the rule. The following brief sketch of the geological structure of the Marquette deposits will indicate some advantages of the method of mining employed. The iron-bearing (Huronian) series of rocks, are stratified beds, the principal ore formation being overlaid by a quartzite, and underlaid by a diorite, or greenstone. This ore formation is made up, first, of pure ore ; second, of a mixed ore" (i. e., banded * A second part of this paper was read before the American Society of Civil Engineers. Both papers are embraced in Chapter IX, Part I, Vol. II, Geological Survey of Michigan.

Jan 1, 1873

By Orville R. Lyons

CENTRIFUGAL force has been utilized for the dewatering of fine coal for over 50 years by means of machines commonly called centrifugal dryers. In any centrifuge the coal and water are subjected to a spinning action which usually inctedtocreases in intensity as the coal progresses through the machine. This spinning action, or the centrifugal force that it induces, tears water away from coal particles and produces a dewatered coal. The effectiveness of the dewatering action for any particular machine is governed by the size-consist of the coal and the centrifugal force imparted to the water on the coal. Four makes of centrifuge are currently being used to dewater fine bituminous coal in the United States. These include the vertical, basket-screen C.M.I. (Centrifugal and Mechanical Industries) Carpenter, Reineveld, and the horizontal solid-bowl Bird. The C.M.I. and Reineveld centrifuges are similar in construction and are variations of the Elmore centrifuge, varying principally in the slope of the basket, operating speed, size of perforations in the basket, and diameter of the basket. The same operating description suffices for both. These centrifuges are made up of two rotating elements, an outside conical screen frame and an inside solid cone which carries spiral pusher blades. The screen frame is supported by a hollow shaft, and the solid cone by a spindle shaft passing through the hollow shaft. Both the screen frame and the solid cone rotate at high speeds; the solid cone, with its scraping flights, rotating somewhat more slowly than the screen. The wet coal enters the machine at the top, falls on the cone, and is thrown against the screen by centrifugal force. The coal slides down the screen until it meets the upper end of the flights, where it is moved slowly along the flights until discharged at the bottom. The elfluent passes through the sieve basket or screen and discharges into a launder. The Carpenter centrifuge consists of a conical rotating element with a vertical axis, built up of three rows of perforated stainless-steel plates or stainless-steel wedge-wire or round-wire sections cut and rolled to conform to the surface of the cone. Wet material is delivered to a conical hopper inside the centrifuge casing and is distributed in a thin, even layer over the inner surface of the cone by a disk mounted on the rotor shaft. Impacting of the coal against the screen and the centrifugal force exerted as the material moves downwards creates a dewatering effect. The moisture is forced through the coal bed and then through the perforated plates of the basket, collecting in a circular trough built into the centrifuge. The effluent is conducted from the trough through the centrifuge casing by outlet pipes. The dewatered coal is discharged over the inside bottom edge of the rotor. The Bird centrifuge consists of a tank or truncated conical shell, which is revolved at the desired speed by means of a drive sheave. A screw conveyor rotates inside the cone or bowl at a slightly lower speed in the same direction of rotation. The feed entrance, in the center of the large end of the truncated cone, is high enough to allow formation of a pool of slurry. Adjustable effluent-discharge ports are located in the large end of the bowl so the level of the liquid can be regulated. The solids are moved forward by the screw conveyor as fast as deposited and carried above the level of the pool for an interval before leaving the bowl. In the past these four makes of centrifuge could be compared only by indirect means. The author published a rough comparison method in 1949' but

Jan 1, 1952

By O. B. Hopkins

The reports for the years 1942 and 1943 were written in 1943 and 1944, respectively, and were summarized at the meetings of the Institute in February 1941 and February 1944, but were held in manuscript form until released for publication in 1945. 1942 During the year 1942, developments in the Peruvian oil industry continued to be subject to repercussions from the swelling war effort, which steadily diverted more of the normal supply of men and materials into war channels, and necessitated the rerouting of supply lines. The result in Peru was an increasing demand for crude oil and products. The production of petroleum in Peru in 1942 was 13,626,259 bbl., as compared with 11,935,584 bbl. in 1941—an increase of 1,690,675 bbl., or approximately 14 per cent. The largest increase, amounting to over 61 per cent, was from the Lobitos fields, but this increase was caused largely by the subnormal production in 1941. International Petroleum Company's production in the La Brea y Parinas field increased 727,111 bbl., or 7 per cent, whereas the Peruvian Government's production in the small Zorritos field declined 10,380 bbl., or approximately 20 per cent. The final production figures for the Ganso Azul field at Agua Caliente were not available for 1942 at the end of the year, but the production was believed to have increased approximately 80 per cent from 1941, or from 13,750 to approximately 25,000 barrels. Development and Exploration Exploration in Peru in 1942 was very limited and confined to areas adjacent to the older producing fields, and the efforts there were largely expended in the extension and development of the producing areas. This situation resulted partly from the shortage of transportation and drilling equipment, and also from the strong demand for increased production of oil. . International Petroleum Co. completed 69 wells during the year, including seven exploratory wells, three of which added moderate extensions to the proven areas. Sixty of the completions were oil wells and nine were dry holes. Lobitos Oilfields, at Lobitos and Restin, is understood to have concentrated its drilling effort on development rather than on exploration. The Peruvian Government operating at Zorritos confined its drilling to the development of the small producing areas previously found. During the year it announced plans to drill three exploratory wells in the Pirin area of southern Peru (see map on p. 638). It was reported that the Government had made a survey of the Sechura area (representing the southern part of the Northern National Reserve as shown on the map), but no work under this arrangement was announced. The Cia. Ganso Azul, at Agua Caliente, completed its No. 6 well as a producer on March 27, and during the year it completed the installation of a 400-bbl. topping plant.

Jan 1, 1945

By Walter Knox, Charles H. Sawyer

All of the coals commonly used in domestic bituminous stokers form coke, and satisfactory operation depends upon the fact that the coke formed is so weakly bound together that it breaks readily in the normal operation of the stoker and automatically maintains a good fuel bed. Some coals, because of their tendency to form solid, blocky coke, are practically excluded from use in small domestic stokers as now built. Other coals, some among the best stoker coals available, can form this troublesome coke under certain conditions. Many contradictory methods have been offered as cures for coke formation. Generally the procedure has been to try various adjustments until a combination was found that seemed to give better results. Such random methods of treatment have not provided any reliable information as to causes. The present paper covers a comprehensive test program undertaken by the Koppers Company's Stoker Coal Research Laboratory at Kearny, N. J. The program had two main objectives; first, to discover what factors affected coke formation, and second; to define corrective steps that could be applied in stoker service work. Conclusions and Results i. The design of the stoker outweighs in importance all other factors capable of improving coke formation. 2. Insufficient air supply aggravates the formation of large blocky coke, although raising the air above 30 to 40 per cent excess (as determined during steady running) does not further improve the character of the coke formed and only reduces its accumulation at the expense of efficiency, increased fly ash, poorer clinker-ing, and other disadvantages. 3. Increasing the coal feed results in a somewhat more friable coke structure and is recommended for persistently troublesome jobs. 4. Increasing over-fire draft improves the character of the coke formed and reduces troublesome accumulations by accelerating off-period burning, although at some expense in efficiency and some increase in fly-ash accumulation. 5. Coke structure was not substantially improved by blocking some of 'the retort tuyeres, although the blocking of tuyeres at the feed-screw end of a rectangular retort did lead to somewhat improved performance, possibly because of considerably better distribution of coke in the fuel bed. 6. With the equipment tested no difference was shown between installation of the same stoker in a steam boiler and a warm-air furnace, or between a sand-filled and a ventilated type of hearth. 7. The following design features had no noticeable effect on coke formation: a. Presence or absence of coal-tube air as provided by many manufacturers to eliminate smoke-back. B. Presence or absence of a flap damper ill the air duct to minimize off-period burning. c. Continuous or intermittent (ratchet and pawl driven) movement of fuel feed screw.

Jan 1, 1944

By Charles H. Sawyer, Walter Knox

All of the coals commonly used in domestic bituminous stokers form coke, and satisfactory operation depends upon the fact that the coke formed is so weakly bound together that it breaks readily in the normal operation of the stoker and automatically maintains a good fuel bed. Some coals, because of their tendency to form solid, blocky coke, are practically excluded from use in small domestic stokers as now built. Other coals, some among the best stoker coals available, can form this troublesome coke under certain conditions. Many contradictory methods have been offered as cures for coke formation. Generally the procedure has been to try various adjustments until a combination was found that seemed to give better results. Such random methods of treatment have not provided any reliable information as to causes. The present paper covers a comprehensive test program undertaken by the Koppers Company's Stoker Coal Research Laboratory at Kearny, N. J. The program had two main objectives; first, to discover what factors affected coke formation, and second; to define corrective steps that could be applied in stoker service work. Conclusions and Results i. The design of the stoker outweighs in importance all other factors capable of improving coke formation. 2. Insufficient air supply aggravates the formation of large blocky coke, although raising the air above 30 to 40 per cent excess (as determined during steady running) does not further improve the character of the coke formed and only reduces its accumulation at the expense of efficiency, increased fly ash, poorer clinker-ing, and other disadvantages. 3. Increasing the coal feed results in a somewhat more friable coke structure and is recommended for persistently troublesome jobs. 4. Increasing over-fire draft improves the character of the coke formed and reduces troublesome accumulations by accelerating off-period burning, although at some expense in efficiency and some increase in fly-ash accumulation. 5. Coke structure was not substantially improved by blocking some of 'the retort tuyeres, although the blocking of tuyeres at the feed-screw end of a rectangular retort did lead to somewhat improved performance, possibly because of considerably better distribution of coke in the fuel bed. 6. With the equipment tested no difference was shown between installation of the same stoker in a steam boiler and a warm-air furnace, or between a sand-filled and a ventilated type of hearth. 7. The following design features had no noticeable effect on coke formation: a. Presence or absence of coal-tube air as provided by many manufacturers to eliminate smoke-back. B. Presence or absence of a flap damper ill the air duct to minimize off-period burning. c. Continuous or intermittent (ratchet and pawl driven) movement of fuel feed screw.

Jan 1, 1944

By W. J. Carlson, S. M. Parmerter, I. Iwasaki

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates. It also deals with the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when an-ionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were affected most strongly by the level of starch, to a lesser degree by the pH, and virtually not at all by the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semitaconite could be readily attained with starch and calcium chloride. A previous article discussed some of the parameters that are important when various corn starches are applied to the soap flotation of activated silica from iron ores and to the flocculation of iron ore slimes.' Methods of solubilizing the starches and the molecular size after mechanical and thermal treatments, as inferred from the viscosity measurements, were shown to influence the adsorption characteristics on iron ores, and the residual concentrations of both calcium ion and starch in the pulp liquor were in direct correlation with the flotation and flocculation behavior.2-4 The present article summarizes the results of more recent tests conducted to ascertain the role of starches and starch derivatives in various phases of iron ore beneficiation. The scope of this investigation has been extended to include not only anionic and cationic flotation, but also the flocculation and filtration of iron oxide slimes, the selective flocculation and partial upgrading of semitaconites, and the flocculation and clarification of magnetite-taconite tailings —all problems that are of vital importance to the iron ore industry of Minnesota. By combining a practical approach with adsorption studies and by using single-mineral systems5 in these research efforts, it is believed that the ultimate goal of developing a suitable modification of starch structure may be realized. The topics covered in this article are limited to the empirical aspects of the research program on the depressant activity of starches and products in the cationic and anionic flotation of silica and of their role in flocculation, water clarification and filtration. ANIONIC SILICA FLOTATION In the soap flotation of activated silica from iron

Jan 1, 1970

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO' afe aFeO ' aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K'. Making these changes, 7

Jan 1, 1942

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO' afe aFeO ' aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K'. Making these changes, 7

Jan 1, 1942

By Kenneth C. Vincent, A. M. Gaudin

IN a study1of the action of amyl xanthate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form 1 then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleachable xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete monomolecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene solution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral-a phenomenon that was totally unexpected yet remains interesting and perhaps important. METHOD OF RADIOACTIVE SPIES The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by Pollard and Davidson.3 The method was first developed by Von Hevesy and Paneth in 1913, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method. A fundamental tenet of the method is that a radioactive atom and a nonradioactive atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1944

By A. G. Roach

This paper deals with a plant built under joint agreement between the Canadian and United States Governments to supply the strategic mineral, corundum, at a time when African production was dwindling and war demands still increasing. The operation began in September 1944, retreating the tailings from a former mill by gravity methods, and is still in production (Sept. 1946). In 1942, when it became apparent that South African production would be insufficient to meet mounting wartime requirements of corundum, a survey was made of Canadian sources of the mineral, at the request of the Foreign Economic Administration of the U. S. Government. The investigation' indicated that the quickest and cheapest supply would be obtained by reworking the tailings deposit at Craig-mont, Ontario. Sampling of the dump by Canadian Government engineers revealed that 125,000 tons of tailings, averaging 2.96 pct corundum, was available for retreat-ment. Ore-dressing tests on representative samples of the deposit were conducted by the writer in the laboratories of the Industrial Minerals Section of the Department of Mines and Resources at Ottawa; and gravity concentration on tables was indicated as the most suitable method of treatment. Decision to proceed with the project was deferred until May 9, construction was begun on May 18, and tune-up operation of the plant begun on Sept. IS, 1944. Corundum—Its Properties and Uses Corundum is an oxide of aluminum having the formula Al2O3. Its outstanding characteristic is its great hardness; 9 in the Mohs scale. In this respect it is second only to the diamond. It usually occurs in barrel-shaped crystals in nepheline syenites and other feldspathic rocks deficient in silica. It has a specific gravity of 3.95 to 4.1 and is insoluble and infusible. In color it ranges from white, through red and green, to black. Ruby and sapphire are gem varieties of corundum. Corundum is supplied to industry as closely graded grain.= The coarser roducts (10 to 24-mesh) are used largely for snagging wheels in the steel-castings industry, while the finer grades (from 70-mesh down to flours) find a wide application in the polishing of lenses and for other uses in the optical trade. All sizes of corundum grain are in close competition with synthetic abrasives such as carborundum and alundum. In some fields of application the artificial product is superior to the natural grain but not in' all. The shape of the particle and its behavior under conditions of actual use determine its sphere of employment. The United States is the largest 'Onsumer of corundum, annual consumption in peacetime approaching 3000 tons; during the war this figure was roughly doubled. During the years 1902 to 1913, the bulk

Jan 1, 1948

By A. G. Roach

This paper deals with a plant built under joint agreement between the Canadian and United States Governments to supply the strategic mineral, corundum, at a time when African production was dwindling and war demands still increasing. The operation began in September 1944, retreating the tailings from a former mill by gravity methods, and is still in production (Sept. 1946). In 1942, when it became apparent that South African production would be insufficient to meet mounting wartime requirements of corundum, a survey was made of Canadian sources of the mineral, at the request of the Foreign Economic Administration of the U. S. Government. The investigation' indicated that the quickest and cheapest supply would be obtained by reworking the tailings deposit at Craig-mont, Ontario. Sampling of the dump by Canadian Government engineers revealed that 125,000 tons of tailings, averaging 2.96 pct corundum, was available for retreat-ment. Ore-dressing tests on representative samples of the deposit were conducted by the writer in the laboratories of the Industrial Minerals Section of the Department of Mines and Resources at Ottawa; and gravity concentration on tables was indicated as the most suitable method of treatment. Decision to proceed with the project was deferred until May 9, construction was begun on May 18, and tune-up operation of the plant begun on Sept. IS, 1944. Corundum—Its Properties and Uses Corundum is an oxide of aluminum having the formula Al2O3. Its outstanding characteristic is its great hardness; 9 in the Mohs scale. In this respect it is second only to the diamond. It usually occurs in barrel-shaped crystals in nepheline syenites and other feldspathic rocks deficient in silica. It has a specific gravity of 3.95 to 4.1 and is insoluble and infusible. In color it ranges from white, through red and green, to black. Ruby and sapphire are gem varieties of corundum. Corundum is supplied to industry as closely graded grain.= The coarser roducts (10 to 24-mesh) are used largely for snagging wheels in the steel-castings industry, while the finer grades (from 70-mesh down to flours) find a wide application in the polishing of lenses and for other uses in the optical trade. All sizes of corundum grain are in close competition with synthetic abrasives such as carborundum and alundum. In some fields of application the artificial product is superior to the natural grain but not in' all. The shape of the particle and its behavior under conditions of actual use determine its sphere of employment. The United States is the largest 'Onsumer of corundum, annual consumption in peacetime approaching 3000 tons; during the war this figure was roughly doubled. During the years 1902 to 1913, the bulk

Jan 1, 1948

By B. M. Larsen, L. S. Darken

SOME years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general. our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2-by a high concentration of active (or "free") lime and of manganese oxide dis) solved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. DISTRIBUTION OF MANGANESE BETWEEN SLAG AND METAL AT EQUILIBRIUM On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction [FeO + Mn ;7± MnO + Fe [A] slag metal slag metal] the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as [K" aFPI OFeO ? aMn] where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term aFe may he combined with K" to give a new constant K'. Making these changes.

Jan 1, 1942

By Y. Dardel

Since the first determination of Dumas1 in 1880, many authors have tried to measure the solubility of hydrogen in solid aluminum, or at least the amount of dissolved gas in it. However, the interpretation of the results which have been obtained is still difficult. Sieverts? then Baukloh and Oesterlen,a during their gassing experiments could not determine any solubility of hydrogen in solid aluminum. On the other hand, Portevin, Chaudron and Moreq4 leaving the determination of the hydrogen solubility beyond the scope of their experiments, measured only the amount of gas that they could extract by high voltage positive ion bombardment and found up to 151 cm3 of gas per I00 g of metal. Winterhager,6 by repeated vacuum extraction during severe cold rolling, extracted up to 161 cm3 per 100 g. In both series of experiments, the extracted gas contained chiefly hydrogen with a small amount of nitrogen, carbon monoxide, carbon dioxide and methan. Later, Schmidt and von Schweinitze as well as Chaudron and Moreau7 showed the importance of the adsorbed layer of hydrogen, the extracted quantities being proportional to the surface and not to the weight of the sample, when its cleaning was not perfect. In earlier experiments, Steinhausers extracted from more massive samples nothing but a little amount (< 0. 5 cm3 per I00 g) of hydrogen, carbon monoxide and methane. Thus, according to these experiments the quantity of dissolved gas is probably very small and the effect of the surface could falsify the results of the extraction. However, owing to the care taken by Chaudron and his coworkers, it was clear that all the hydrogen extracted could not come from the superficial layer, or that the links which bound hydrogen to the surface were so strong that the usual method of cleaning could not destroy them. After the main parts of the experiments reported here had already been carried out, Eborall and Ransley9 published the results which they obtained with an analysor having an accuracy of 0.03 cm3 per I00 g, while that of the usual apparatus was only about 0.2 cm3 per I00 g. During all their experiments the adsorbed layer would have been a difficulty, for the value of the adsorbed hydrogen was approximately equal to that of the dissolved amount. Table i—Amount of Adsorbed and Dissolved Hydrogen (After Eborall and Ransley) Extraction Hz Adsorbed „ h2 dissolved Temperature Calculated Extraction OCcma 500 0.057 0.050 600 0.062 o.096 Since always keeping the same adsorbed layer is very difficult, an error in the correction for the adsorption can be made when using the apparatus of. Eborall and Ransley, as well as the earlier apparatus.

Jan 1, 1949

By R. A. Wagstaff

Since the time of the early Egyptians, the use of copper: has been a boon to the life of most of the civilized world. Its use has been varied; in many connections, the art by which it attained its greatest usefulness has been lost. In this paper an endeavor will be made to take into consideration some of the many changes that have occurred during the last 40 years of copper-smelting operations. During that period the copper blast furnace has been almost forced out of existence by new methods of ore concen-tration—first, gravity concentration, and then flotation. These new methods of concentration introduced many new factors into the metallurgy of copper. The product was wet, it was fine and it was high grade. To overcome all these factors many changes have been necessary throughout the smelting agenda. New equipment has been necessary for transportation, unloading, sampling, bedding and moisturing in all smelting plants, especially the custom smelter&apos; During the early days of "flotation," little was known about filtering or the use of an alkaline circuit; often the concentrate going to the smelter contained 2&apos; to &apos;5 Per cent moisture. It is easy to imagine the difficulty arising with a product of this nature when it had to be shoveled by hand labor. To meet these conditions, mechanical unload- ing and sampling devices were soon developed. In many instances such good progress was made that actual costs for handling this unfavorable product were lower than those formerly incurred on the old product. Today most sampling of copper ores and concentrates is being done by mechanical sampling, pipe or augur sampling, or shovel sampling. Where concentrates are uniform in metal content, a great many of the plants now use pipe or augur sampling. For spotty ores, the old shovel sample with cone and quartering during the final stages is still in&apos; use. Where big tonnages are handled, mechanical sampling of concentrates is being done, with satisfactory results. To curtail slow and tedious cutting and mixing procedure, mechanical mixing boxes, splitters and cutters are used to cut down labor costs. Milling As crude ores become scarcer, the use of milling operations increases. The few crude ores that are still smelted are used as fluxing types. To use these ores finer grinding has been found advantageous. This has made for better bedding and fluxillg conditions, which in turn makes for faster smelting, lower fuel consumption and better metal recovery. The degree of fineness is more or less determined by the nature of the product. Most plants have set a standard of through 3/8-in. mesh screen for roaster -reverberatory smelting and through 3/4-in. mesh screen for converter fluxes. For some refractory Ores, even finer grinding has been found to be advantageous for good reverberatory smelting-

Jan 1, 1944

By R. K. McGeary, B. Lustman

Orientation relationships and rates of annealing of 97 pct cold rolled zirconium have been studied by X-ray techniques, metallography, and by hardness measurements. The process of annealing occurring by the formation of domains, and their subsequent growth without recrystallization, is demonstrated. NUMEROUS investigators1-&apos; have revealed sub-grain formation after annealing cold worked metal single crystals and have generally described the results in terms of a dislocation mechanism of polygonization.5,6 in heavily cold rolled polycrystal-line aluminum the first stages of heating cause an apparently spontaneous subdivision of regions of the deformed matrix into a great number of slightly disoriented domains followed or accompanied by rapid growth of certain domains to form a recrystallization texture.7,8 In the present investigation the isothermal rate of annealing of cold worked polycrystalline zirconium has been studied by X-ray techniques, metallography, and by hardness measurement. It will be shown that, rather than by the usual nucleation and growth mechanism,"12 the process of annealing can best be explained by the formation of domains early in the annealing treatment and the subsequent growth of these domains without recrystallization. Experimental Procedure All the experimental work was performed on an arc-melted ingot of high purity zirconium crystal bar made by Westinghouse in a production scale deBoer unit. The weight percentage of impurities in the zirconium were as follows: C, 0.04; Fe, 0.05; Hf, 0.014; W, 0.01; Ti, Ni, and Al, 0.003; Si and N, 0.002; Cr and Cu, 0.001. Metallographically the zirconium showed only a single phase. The 4 in. diarn ingot was forged at 760°C to a 1 1/2x3 in. plate and was then rolled at 760°C to 0.150 in. thickness and annealed at this temperature for 20 min to produce an equiaxed grain structure of about 0.1 mm average grain diameter. The hot rolled plate was roller-leveled, surface ground to 0.135 in., cold rolled 83 pct reduction in thickness on a two-high mill, and then to a total reduction of 97 pct on a Sendzimir mill. The 0.004 in. strip material so produced received no subsequent mechanical treatment. Specimens % in. square were sheared from the rolled strip and isothermally annealed at 104 mm Hg in an all glass vacuum system equipped with a Vycor furnace tube. The temperature data presented are the average temperatures during the runs and did not vary more than about k3"C. X-ray Diffraction Methods: When zirconium is drastically cold rolled, a high degree of preferred orientation results in which prism poles, {1010}, are perpendicular to the rolling direction. After fully annealing this material an entirely new texture develops which corresponds to a 20" or 40" rotation of the deformation texture about hexagonal axes of

Jan 1, 1954

By M. T. Worley

This paper reports investigative work conducted to develop a method of estimating the groundwater influx from a homogeneous permeable formation into a vertical mine shaft during sinking. A method of analysis was developed using data obtained from pumping tests and a modification of the Theis non-equilibrium interpretation technique. Excess influx of groundwater into mine shafts has long been one of the more important problems encountered in the development of a mining property. Much work has been done on methods of preventing such influx and on pumping schemes to control inflow if preventive measures fail. The fundamental aspects of the problem, on the other hand, seem to have been neglected. The purpose of this paper is to review the fundamentals of groundwater flow and to propose a rapid method of analyzing hydrologic data in order to estimate influx from a homogeneous permeable formation into a mine shaft. Such an estimate of the quantity of water to be encountered is of value in planning grouting, pumping and other programs designed to control that influx. It is emphasized that the proposed method of analysis should be regarded only as a tool to be used in evaluating the problem before investing the capital necessary to begin development of a property. FUNDAMENTALS OF GROUNDWATER FLOW In order to effectively approach the problem of estimating influx into a mine shaft, a knowledge of the fundamentals of fluid flow through a porous medium is necessary. Darcy, in 1856, developed an empirical relationship to explain the flow of water through sand filters. This relationship V = k (dh/dl), is the basis for all other flow formulae. It has been shown that Darcy&apos;s relation is a solution of the Laplace equation and thus is analagous to other natural phenomena such as heat flow. Theis, using the analogy of heat flow by conduction, developed an expression for determining the transient or time-dependent groundwater flow through a homogeneous, isotropic medium. The resulting equation Was also derived by Jacob using hydrologic considerations alone.&apos; The individual terms in the equation are described in Table I. It is important to understand the assumptions upon which this equation is based. 1) The medium through which the fluid flows is infinite in areal extent, homogeneous and isotropic. 2) The well into which the fluid discharges completely penetrates the medium. 3) The characteristics of the medium remain constant at all times. 4) The initial pressure surface is horizontal. 5) The confining media are impervious and horizontal. 6) Fluid is removed from storage instantaneously by a decline in pressure. 7) The diameter of the discharge well is infinitesimal with respect to the drainage radius of the medium.

Jan 1, 1962

US 4,152,143-Continuous precipitation of cement copper from an aqueous ore leach solution mixed with pieces of iron as the precipitant Copper depositing on the pieces of iron is loosened and removed therefrom by means of constant but regulated oscillating movement of the pieces of iron in a horizontal elongated chamber, and the loosened copper is separated and collected from the mixture E Kausel and R Nissen, assigned to Klockner-Humboldt-Deutz A G May 1, 1979 8 pp (75-100) Filed 1-12-78 (868,981) (Drawings below) [ ] US 4,156,711-Removal of metal impurities from an acidic zinc or cadmium solution prior to electrolysis. Impurities such as manganese, cobalt, nickel, and thallium are selectively precipitated by contacting the solution with persulfuric acid or an ammonium or alkali metal salt thereof while maintaining a pH value of from 1 5 to 4 5 This patent is a continuation-in-

Jan 1, 1980

By G. L. Corrigan, J. R. Coleman

Four factors that largely determine the end product obtained when cement and water are mixed are the chemical compo ition of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the more finely ground a cement, and the greater the surface exposed in proportion to its mass, the more rapid is the hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.1 Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are poorer cementing materials than some of the more finely ground construction cements. On the other hand, often it is necessary to pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concerning the proper fineness range.

Jan 1, 1941

By David P. Shoemaker, Clara Brink Shoemaker

The I phase was discovered by Bardos, Malik, Spiegel, and Beck1 in the V-Ni-Si system at 1100°C and in the Mn-Co-Si and Mn-Ni-Si systems at 1000°C. Kuzma and Hladyshevskii2 and Kuzma, Hladyshevskii, and cherkashin3 have reported a new phase, which they named the S phase, in the Mn-Co-Si and the Mn-Ni-Si systems at 800°C at approximately the I phase compositions. The powder diffraction diagrams of the I and S phases, compared by Bardos el al.,1 are related but show distinct differences in relative intensities. Professor Paul A. Beck kindly sent us a specimen of the (v-Ni-Si) I phase for single-crystal study. Precession and Weissenberg diagrams taken with a tiny single-crystal fragment showed that the structure is monoclinic with a large unit cell. The cell dimensions were refined from a powder diffraction diagram taken with CrKa radiation in a 57.3-mm camera with our computer program LSCELP4 using only the indices of those reflections that were observed on Weissenberg diagrams (hnl, with n = 0 through 9 and n = 12) and precession diagrams (Okl, lkl, Izk0, hkl, hk2). Table I shows the agreement obtained between the l/d values calculated with the final values for the cell dimensions and the l/d values observed by Bardos et al .1 for I(V42Ni33Si25), by US for I(V41Ni36Si23), and by Kuzma and Hladyshevskii2 for S(MnpCoSi). The powder patterns contain many broad and diffuse lines. In fact practically all powder lines observed are near-superpositions of several reflections. The refinement program is not set up to handle several reflections contributing to one observed line: the position of each line is refined with the aid of one set of indices only. The final values for the cell dimensions were obtained from the lines of strong or medium intensity with the indices indicated by asterisks in Table I: a0 = 13.403(6), bo = 23.336(15), co = 9.129(6)A ß = 99.11(6) deg The standard deviations (given in parentheses) are those calculated by the refinement program from least-squares theory and do not take into account that the lines included in the refinement may not have been correctly indexed in every case or that the position of a line may also be partly determined by the overlapping reflections. The agreement between the calculated and observed I phase patterns is fairly good, although some discrepancies occur. Not all observed lines could be indexed with the incomplete set of sin-

Jan 1, 1968