Search Documents

By P. Chaudhari, Michael B. Bever

The heat of solution at infinite dilution of selenium in bismuth, the heat of mixing of selenium and bismuth, and the limit of solubility of selenium in bis~rzuth have been determined at 573, 623; and 663°K by metal solution calorimetry. The heat of forrrzation of the compound Bi2Se at these temperatures has been determined from the heat effects associated with the precipitation of the compound from a saturated solution oj selenium and bismuth. The published information on the thermodynamic properties of the system Bi-Se is limited. The heat of solution at infinite dilution of selenium in bismuth at 623°K has been measured.' The heat of formation at 273 K1 and room temperature2 and the heat capacity at 80 K3 of the compound Bi2Se3 have been reported. An estimate of the heat of formation of the compound BiSe at room temperature has been published.2 Information on the phase relations in the system Bi-Se is available.' In the investigation reported here the following quantities have been determined at 573", 623", and 663°K: 1) the heat of solution at infinite dilution of selenium in bismuth, 2) the heat of mixing of selenium and bismuth in bismuth-rich solutions, 3) the limit of solubility of selenium in bismuth, and 4) the heat of formation of the compound BizSe. These quantities were determined by the addition of selenium to bismuth-rich solutions in a metal solution calorimeter. The determination of the heat of formation at the tem- perature of the calorimeter bath involved the precipitation of the compound from a saturated solution in the calorimeter. 5,6 This method differs from that commonly used which requires the addition of the compound and of a mechanical mixture of its components and yields the heat of formation at the temperature from which the additions are made (273 K EXPERIMENTAL PROCEDURE AND CALCULATIONS The solution calorimeter has been described in detail.' Pure bismuth (99.999+ pct) was used as the bath at the start of a run. The calorimeter was calibrated with small amounts of bismuth added from 273°K; the differences of the heat contents of bismuth at 273°K and the temperatures of the baths are listed in Table I. After the calibration, additions of hexagonal selenium (99.999+ pct) were made. Loss of selenium by evaporation was negligible. No unusual experimental difficulties were encountered.9 The differences in the heat contents10 of selenium at 273°K and the temperature of the bath, listed in Table I, were subtracted from the measured heat effects to give the "adjusted heat effects". The methods by which the heat of solution at infinite dilution, the

Jan 1, 1968

By H. D. Kessler, Joseph B. McAndrew

WHEN there is occasion to make structural use of metals at temperatures above 900°C (1652°F), the choice of alloys is severely limited, and those materials which meet special requirements as to density, strength, toughness, and resistance to creep, oxidation, or fatigue at such temperatures are at a premium. Any new type of high temperature alloy which is found to be outstanding with respect to several of these properties is therefore likely to find special applications for which it is uniquely advantageous as compared to other alloys. Such is the case with the 7 titanium-aluminum alloys. This y phase is an intermediate phase based on the composition TiAl, and extends from about 35.5 to 44.5 wt pct Al at temperatures up to 1000°C, above which the field broadens to include 60 pct A1 at 1340°C.' The alloys of principal interest have a narrow melting range, with 7 forming by the peri-tectic reaction, melt + ß=y at about 1460°C. Unlike most intermediate phases, the binary alloys containing titanium and aluminum in approximately equiatomic proportion possess low room temperature hardness,' in addition to which they have low density, good resistance to oxidation, and relatively high modulus of elasticity.' Unpublished work done at Armour Research Foundation showed

Jan 1, 1957

By B. J. Kochanowsky

To improve blasting methods it is necessary to know how the explosive force acts and how rock resists this force. Because of the tremendous power developed within milliseconds and the great number of other factors directly affecting the technical and economic results, an analysis of the fundamentals of blasting theory is difficult. But since the rules used for layout design and for calculations of size of explosive charges are based on theoretical assumptions, complete knowledge of blasting theory has great practical importance in mining. Analysis of Blasting Theory: It is interesting to note the opinion of blasting experts with respect to contemporary blasting theories. F. Stussi,' Professor of the University of Zurich, stated: "We do not have enough experience yet to change our army engineering regulations in blasting and base it on new fundamentals. It is our duty to collect more practical data and to do more research in blasting to close this gap." K. H. Fraenkel,' editor of the Manual on Rock Blasting published in 1953 in Sweden and written by well-known Swedish, German, Swiss, and French blasting and explosive experts, said: "To the best of our knowledge no suitable formulas for civil blasting work are to be found in the American, French or German literature."

Sep 1, 1955

By C. F. Tolman

Discussion of the paper of C. F. TOLMAN, JR., presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 401 to 433. Louis C. GRATON, Cambridge, Mass.-Of particular interest at this time is any paper that deals with chalcocite, the characteristic product of secondary enrichment and the copper mineral of greatest commercial importance, and that seeks to aid in the distinction between primary and secondary chalcocite-a distinction of much scientific and practical importance but one which thus far it has proved difficult to draw. The present paper on this subject by Professor Tolman, like the ,many preceding it which he and his colleagues at Stanford have published in the last couple of years, contains much of interest and suggestiveness. Without endeavoring at this time to review or comment upon Professor Tolman's conclusions in detail, I may say that many of them are in accord with the findings that my associates and I have been accumulating in the course of studying secondary enrichment in many of the copper deposits of the country. On the other hand, it goes without saying that in this comparatively new field of research or, at least, a field in which

Jan 5, 1916

By R. L. Segall

AN unusual thermal etch figure in copper is described and an explanation in terms of twinning is suggested. A flat polycrystalline specimen of OFHC copper cut from a rolled sheet was electro-polished in orthophosphoric acid and annealed at 950°C in a vacuum of approximately 10-3 mm Hg for 2 hr. The specimen was found to be thermally etched, the markings on the surface being consistent with the assumption that they were the traces of the (111) planes which are developed preferentially because they have the lowest free energy. However, on one grain (the grain shown in Fig. 1) the traces formed an almost regular pentagon and at first sight it seemed unlikely that they could all be (111) traces. These traces were studied further because it was thought that they might be a type of growth spiral. A fringe pattern showed that this was not so, the grain being sensibly flat and the only features having steps were the striations and the faint curved line passing out from the center of the pentagons. To obtain some additional information, the specimen was deformed in tension. The effect of the stress was first to cause the appearance of lines running from the centers to the apexes of the pentagons and then to tilt the five segments so formed. At a much greater stress, appreciable slip appeared on the grain; these effects can be seen in Fig. 2. The micrograph was taken at a fairly late stage in the deformation and the tilting is quite marked. The magnification is the same as in Fig. 1, and although some slip can be seen it could be observed better by varying the illumination and using higher magnifications. In each segment of the grain, slip (which takes place on the (111) planes) was parallel to the side of the pentagon in that segment. The marked changes in direction of slip from segment to segment seemed to be incompatible with the presence of a regular array of subgrains. These results suggest that some of the five segments were twins. If this is so, since the twinning plane in copper is the (111) plane, the radial lines must be traces of the (111) planes on the surface. From the symmetry of the striations about the radial lines, these planes must be almost perpendicular to the surface. The angle between <III>directions in face-centered-cubic copper is 70&apos;32&apos;. If, in Fig. 3, OAB (triangle 1) is taken as matrix and OA, OB are (111) planes viewed edge on, then AB is in the correct direction to be the trace of either of the other two (111) planes on the surface. If triangle 2 is the twin (about the (111) plane perpendicular to the surface and containing OB) of triangle 1, then once again it can be shown that all lines are traces of (111) planes. Similarly, triangle 3 is the twin of triangle 2, 4 of 3, and 5 of both 4 and 1. (The sequence is, of course, quite arbitrary.) However, if this were the case there would be a discrepancy of 7&apos;20&apos; to be accounted for. It is suggested that the faint curved line passing outward from the center of the pentagon represents either a low angle boundary or a sixth small twin. The slight step shown by the fringes at this line might be an indication that the former is the case. This explanation does not account for the coincidence of obtaining a grain whose surface must be so close to (110) and obtaining the curious twinning described previously; it would be of interest to find a specific mechanism for this.

Jan 1, 1958

By B. Ancker, E. R. Parker

The small-angle dislocation-boundary density of nickel and some of its alloys was investigated as a function of strength. It was found that the strength is a linear function of the density for pure nickel and for Ni-Ti alloys, but not for Ni-Co alloys. The results are interpreted in terms of dislocation theory. THE processes by which metals deform are still poorly understood, even though there has been a concentrated research effort in this field during the past fifteen years. Single crystals and individual grains in polycrystalline aggregates often develop a subgrain structure when deformed. Substructure formation occurs as a result of local plastic bending and its development is augmented by annealing at moderate temperatures.&apos; Investigations made to date, largely qualitative in nature, have shown that the substructure is composed of a network of small-angle boundaries. The purpose of the present paper is to present some quantitative data on substructure (obtained by X-ray techniques) and to correlate the results with the strength of the metal in which the substructure existed. Nickel and some of its alloys were used for the experiments. The presence of certain kinds of foreign atoms greatly alters the formation and effect of the substructure. Polycrystalline tensile specimens were prepared from high purity nickel, two Ni-Ti alloys, and two Ni-Co alloys; the composition of these materials is given in Table I. Tensile specimens having a reduced section 1/4 in. diam by 3 in. long were machined from materials which were refined, cast, forged, and swaged in the authors&apos; laboratories. The specimens were annealed for 1/2 hr at 1150°C, a treatment which produced grains having a diameter of approximately 0.5 mm. This rather large grain size was used to facilitate later examination of the substructure. Duplicate specimens of pure nickel and of each alloy were strained various controlled amounts in tension at room temperature and recovered for 1 hr at 800°C. (This strain induced prior to recovery will be referred to hereafter as the "prestrain.") One of each of the recovered specimens was pulled in tension at room temperature to obtain the stress-strain curves. The other bar was cross-sectioned in the gage length, carefully polished, and deeply etched to remove all cold-worked material. This specimen was then examined by the X-ray microscopic technique2 to determine the nature and magnitude of the substructure. The use of duplicate specimens permitted a direct correlation between tensile properties and substructure characteristics. X-ray microscopic studies were made with an apparatus constructed to have an average resolving power of about 4 microns. The monochromatic radiation reflected from grains which were oriented favorably was recorded on fine-grain photographic plates. These were examined at Xl00 which represents the true magnification, since there was essentially none in the X-ray system. This permitted detection of angular differences between subgrains of as little as 10 min. A very large number (over 100) of grains for each specimen was examined at this magnification and the number of substructure boundaries per grain was tabulated. An accurate relative measure was obtained under fixed experimental conditions, e.g., same grain size, resolving power, magnification, etc. The greatest source of error lay in counting the subboundaries, but this proved to be surprisingly small when repeated counts were made by different investigators. Furthermore, as the subsequent analysis indicates, whatever human error was introduced was not significant. Analysis of the Substructure Data When the number of substructure boundaries per grain was plotted against the frequency, skew (asymmetrical) distribution curves of the type shown in Fig. 1 were obtained. These are smoothed curves for the 1 atomic pct Ti in nickel alloy subjected to various prestrains and are representative of the curves obtained with all the metals. Since skew-distribution curves cannot be analyzed by elementary statistical methods, detailed investigations were undertaken in order to 1—test the consistency

Jan 1, 1955

By Vincent T. Ricca, Kurtis Chow

When dealing with acid mine drainage as to treatment levels, costs, and evaluation of abatement schemes, predictions of the quantity and quality of the discharges are needed. An acid mine-drainage model is presented in this paper. In essence, the model is a hybrid of computer programs for stream flow simulation and acid mine drainage. Two major aspects of the model are discussed: mine-water generation and acid-load production. The former is based on hydrologic concepts and the latter on pyrite oxidation kinetics and oxidation product removal. The total model is programmed for the high-speed digital computer. The major inputs are: climatological, basin characteristics, and mine characteristics data. By the use o f the hydrologic model the amount of water that flows through the pyritic system is determined. From this information, acid loads removed by leaching, inundation, and gravity diffusion are then predicted. The outputs from the total model are: average daily mine-water discharge, the associated acid concentration or load, plus the average daily flow in the receiving streams or at basin outlets. The capabilities of the separate models have been tested individually and the joint model has been applied to a small drift mine in southeastern Ohio.

Jan 1, 1975

Abel, Charles Edwin, Student, Univ. of California Los Angeles, Cal. &apos;31 Adams, Horace M.5148 Benton Ave., Downers Grove, Ill. &apos;31 Ahlskog, Harold A., Student, Washington State College Pullman, Wash. &apos;30 Aldridge, John, Student, New Mexico School of Mines Sbcorro,, N. M. &apos;30 Allen, Hugo K., The Univ. of Texas 104 W. 33rd St., Austin, Tex. &apos;31 Ames, Marshall B., Student, Washington State College Pullman, Wash. &apos;31 Ancell, Virgil F., Student,. Missouri School of Mines Rolla, Mo. &apos;30 Anderson, Norman John, Student, South Dakota School of Mines Rapid City, S. D. &apos;32 Annett, Norman T., Student, Mackay School of Mines, Univ. of Nevad Reno, Nev. &apos;32 Apablasa, Salvador C., Student, Univ. of California Los Angeles, Cal. &apos;31 Armstrong, James Arthur, Jr., Student, Michigan College of Min. & Tech., Houghton, Mich. &apos;31 Armstrong, John R. Box 274, Neosho, Mo. &apos;31 Armstrong, Robert H., Student, Lafayette College Easton, Pa. &apos;31 Armstrong, Thomas E., Student, Univ. of California Los Angeles, Cal. &apos;31 Arnot,. Paul H 2617 Haste St., Berkeley, Cal. &apos;31 Ashby: Harve I., Willow Creek Mines Wasilla, Alaska. &apos;31 Aud, Robert A., Student, Lafayette College Easton, Pa. &apos;30 Augenthaler, Robert L., Student, New Mexico School of Mines Socorro, N. M. &apos;32 Augustine, Grant, Jr., Instrument man, Min. Dept., Fairbanks Exploration Co., Fairbanks, Alaska. &apos;31

Jan 1, 1932

By W. R. Aufricht, E. H. Koepf

The theory, measurement, and application of capillary forces in reservoir rock have been treated ex-tensively in the various petroleum publications.1,2,3,4 These forces are of prime importance in oil production, and data on capillary properties are among the most important tools used in the study of reservoir mechanics. The principal application of measured capillary pressure data by the production and reservoir engineer is in the determination of the initial distribution and mobility of fluids in the reservoir. The distribution refers to the magnitude of the oil and interstitial water saturations under capillary equilibrium conditions and to their variation throughout the reservoir as a result of changes in rock properties and nearness to free water. The magnitude of the water (or oil) saturation, as well as the porosity, is required in volumetric calculations of oil in place. In low permeability reservoirs, where long transition zones are common, the magnitude of the oil content, even below the depth interval where commercial rates of flow of oil can be obtained, must be evaluated since this oil contains energy available to the production of the remainder of the reservoir. The mobility of the water phase is of particular importance in water-flood calculations since mobile water may condemn what would otherwise be a successful water flood. In reservoirs with predominantly small pores, high immobile water contents are possible. Conversely, reservoirs with predominantly large pores may contain mobile water even though the interstitial water contents are relatively low. This presentation reviews the distribution and mobility of interstitial water contents as determined from capillary pressure data and shows typical data for various types of carbonate reservoirs. A discussion of the variations found in different types of carbonate reservoirs is given. DISCUSSION Interpretation of Laboratory Data Fig. 1 is a typical laboratory capillary Pressure curve where water saturation as Per cent of Pore space is plotted vs capillary Pressure (psig) for an air-water system. This par- ticular curve was obtained by measurement on a sample of San Andres dolomite with intergranular-type porosity. The sample studied had a permeability of 10.0 md and a porosity of 18.8 per cent. The capillary pressure-saturation relationship illustrated is an inherent property of the rock (a function of the size and distribution of the pores) and represents the ability of this water-wet rock to retain water against the pressure differential exerted by a non-wetting fluid (oil or gas) to remove it. In the laboratory a known pressure differential is exerted from a pressure source; in the reservoir the pressure differential is controlled by the density difference between the hvdrocarbons and the water. The laboratory capillary pressure values may be converted into terms of equivalent height of water column using known values of reservoir oil and water density and measured or average values of interfacial tension

Jan 1, 1958

By A. B. Parsons

Not so many years ago the interest of the average mining engineer in money matters-aside from his pay check or his consulting fees-was confined to the per-ton cost of mining and beneficiating ore and to the amount of capital that would be required to erect the plant necessary to carry out such operations on a prescribed scale. The so-called "business men" assumed that questions of marketing the products, of profits, and of dividends were in their exclusive sphere-matters too intricate or, perhaps, too practical for the mere engineer! In the case of a new enterprise, the promoter shouldered the entire responsibility for raising the necessary funds, and incidentally he got the lion&apos;s share of profits. In fact, he frequently profited handsomely even though the mine earned little or nothing. Occasionally the engineer turned promoter or entrepreneur--conspicuous examples are Herbert Hoover, D. C. Jackling, William Braden and F. W. Bradley- but by and large he remained in a sphere of his own. To what extent this condition of affairs has changed is difficult to say. It might be argued that it were better that it be not changed; and yet I cannot help feeling that in mine promotion lies a distinct opportunity for the

Jan 1, 1932

By Luiz C. Correa da Silva, Robert F. Mehl

A. D. Le Claire and R. S. Barnes (Atomic Energy Research Establishment, Harwell, Didcot, Berks., England)-—This much awaited paper admirably confirms that the Kirkendall effect is a true diffusion phenomenon and likely to be found in all diffusing systems. The most likely explanation put forward so far to account for the shift of interface is that the two components of the system, diffusing in opposite directions, do so with unequal rates so that there is a net loss of material from that half of the diffusion zone rich in the more rapidly diffusing component. This loss is accompanied, and at least partly compensated for, by a closing up or decrease in volume of this latter half of the diffusion zone and an expansion of the other half so as to tend to keep constant the overall volume per atom. This is manifest as a movement of the original interface. If this is a true picture of what is taking place then there are at least two important matters requiring further study."1—The quantitative relating of the observed shift with the independently measured separate diffusion coefficients of the two diffusing species."2—A detailed study of the mechanism and characteristics of the closing up process."We would like first to make a few remarks pertinent to these topics. In connection with the first of these, it is a pity that more and detailed measurements were not made on the Au-Ag system, the only one for which the separate diffusion coefficients of the two species have been measured.&apos;" One of us (A. D. Le C.) has calculated from Johnson&apos;s results the shift to have been expected in samples D.2 and D.3. Darken4 showed that the velocity v with which the markers move is related to the separate diffusion coefficients Dau, Dag, by the eauation:"dN"v = (Dag — Dau "dx"dN"where .is the concentration gradient at the mark-ax"ers. Under certain conditions,4, 20 it can also be shown that:"Xm"v = "2t"where x, is the total marker shift after time, t:"dN". . xm = 2t (Dag — Dau) [9]"dX"Johnson measured Dag and DAu in a chemically homogeneous alloy and so his reported figures represent the true or ideal diffusion coefficients"; the same quantities in eq 9 represent the actual diffusion coefficients as would be measured in the presence of a chemical concentration gradient, so we need to multiply Johnson&apos;s reported values of Dag and Dau by the"1 before insert-dlogN "ing them in eq 9. 7 is the activity coefficient of Ag at the concentration prevailing near the markers which we shall assume to be - 50 pct. The values of the thermodynamic factor for N = 0.5 and the temperatures at which D.2 and D.3 were annealed were obtained from thermodynamic data quoted by Darken.&apos; aN/ax was computed from the coefficient of inter-diffusion of Au and Ag given by Johnson on the assumption that in the samples D.2 and D.3, the concentration distance curve could be represented by the standard equation:""No is the original difference in concentration between the two halves of the couple, and + is the error or probability function."aN/ax at x = 0 is then given by:"adN/dx "2/nDt"and we assume that this represents the concentration gradient at the markers, although it is probable that the figure is slightly high."When all the appropriate quantities are inserted in eq 9, we find that the expected shifts are: for D.2, 0.0134 cm and for D.3, 0.0119 cm."The agreement between these results and those

Jan 1, 1952

By John Wulff, David A. Stevenson

The solubility of iron and cobalt in liquid lead, the solubility of chromium in liquid tin, and nickel in liquid silver were determined up to 1300°C in an atmosphere of hydrogen. Liquid samples were taken at different temperatures and analyzed. The data obtained were plotted to show the relationship between log mole fraction of solute and the inverse of the absolute temperature. Resulting values for the differential heat of solution (AH) and the excesspartial molar entropy (S)are: for the iron-lead system = _24,200 cal per mole and AT = 5.0 e.u. for the a phase, and AH = 18,300 and S = -0.1 e.u. for the y phase; for the cobalt-lead system AH = 16,500 cal per mole and AS =0.7 e.u.; for the chromium-tin system AH = 15,600 cal per mole and AS = 8.5 e.u.; for the nickel-silver system AH =18,000 cal per mole and AS = 4.0 e.u. RECENT developments in coating, brazing, and heat transfer have focused attention on specific cases of solid-liquid interaction in metal systems, particularly those involving dilute liquid solutions. One fundamental quantity of interest in such systems is the equilibrium phase distribution between solid and liquid phases. In any effort to fully understand such interactions, one must be able to describe the equilibrium state precisely. Furthermore, in order to develop genera! relations for such systems, one must know the equilibrium state in a number of different cases. This investigation was devoted to a study of the equilibrium phase distribution in four binary systems: solid iron-liquid lead; solid cobalt-liquid lead; solid chromium-liquid tin; solid nickel-liquid silver. The iron-lead system was previously studied by Shepard and parkman&apos; and later by Fleischer and Elliott2 with differing results. Both investigations were carried out by sampling the saturated liquid, and analyzing it chemically. The cobalt-lead system was previously reported by Pelzel,3 who noticed no discontinuity near the transformation. A limited investigation of the chromium-tin system was made by Wlodek and wulff4 using a weight loss method. This work was done in conjunction with the development of a process for coating molybdenum with chromium from tin solutions. To more fully under- stand the kinetics of the process, a more accurate determination of a solubility was desirable. No significant data were found in the literature on the nickel-silver system. Data on the latter system were, however, relevant to the investigation of the corrosion kinetics of copper-nickel alloys in liquid silver as carried out by Harrison and wagner,5 EXPERIMENTAL APPARATUS AND PROCEDURE Of the techniques available for the study of such systems the most effective appears to be that of liquid sampling,2,6,7 which is the method used in the present investigation. A schematic diagram of the sampling furnace is given in Fig. 1. Large pieces of solute metal, in excess of saturation solubility, were added to 200 g of the solvent metal, and the entire charge placed in an alundum crucible. Analytical reagent or materials of chemically pure grade were used in all investigations. The crucible was contained in a zircon muffle tube positioned vertically in the uniform hot zone of a Globar resistance furnace. The tube was provided with a number of ports which permitted sampling at temperature and in controlled atmospheres or vacuum; the ports were also useful for evacuation and introduction of gases as well as for thermocouple measurements. A chromel-alumel thermocouple Sheated in a porcelain tube was used for temperature measurements. A purified hydrogen atmosphere was employed in all experiments reported in this paper. The hydrogen was purified by passing it first over hot copper gauze to remove oxygen and then through a molecular sieve immersed in

Jan 1, 1962

ST. LOUIS SECTION H. A. BUEHLER, Chairman, CHARLES T. ORR, Vice-Chairman., THOMAS T. BREWSTER, Vice-Chairman, L. L. HUTCHISON, Vice-Chairman, W. E. McCOURT, Secretary-Treasurer, Washington University, St. Louis. CHARLES J. ADAMI, EUGENE MCAULIFFE, A. C. TERRILL, JAMES A. CASELTON, JAMES D. ROBERTSON. The annual meeting of the St. Louis Section was held at the St. Louis Club, Saturday evening, Mar. 10, 1917. Philip N. Moore, President, and Bradley Stoughton, Secretary of the Institute, were the guests of the Section. The meeting was preceded by a dinner, at which 70 were present, and was presided over by F. W. DeWolf. Addresses were made by Mr. Moore and Mr. Stoughton. The routine reports of the officers were- presented and the Executive Committee named above was elected for the current year. The special business of the meeting was a report of progress concerning the arrangements for the Institute meeting to be held in the St. Louis Section district, Oct. 8 to 13, 1917. The general program for the meeting met with the cordial approval and cooperation of the members of the Section. It was evident that the members are united in an endeavor to arrange a successful meeting. W. E. McCOURT, Secretary.

Jan 4, 1917

F. C. LANGENBERGW.*at 8ertoivn,M ass. (written cliscussiont).-I am inclined to the view that the change in physical properties encountered in the material with which the authors are working is due to the relief of internal strains. The statement, on page 1.098 of their paper, calling attention to the fact that this phenomenon disappeared when the material was rolled into 1 7/8 -in. square billets is of particular interest. It is certain that the internal strains set lip by cooling in a small billet of this size would be much less than those produced in a billet having a larger cross-section cooling under the same conditions. The statement that the physical properties of a given test bar were materially changed by standing has been brought to my attention in connection with the testing of gun forgings. I have made a number of observations on forgings produced at Watertown Arsenal to ascertain whether any change in ductility was produced by the aging of the test specimens. The results were always negative, but this can be explained by the fact that ii gun forging is generally a forging that has been quenched and subsequently drawn at a relatively high temperature.

Jan 10, 1919

Jan 1, 1965

Discussion of the paper of WALTER 0. SNELLING, presented at the New York meeting, February, 1915, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704. A. F. LUCAS, Washington, D. C.-Are the results of the experiments in practical operation? WALTER 0. SNELLING.-There have been no large-scale operations up to the present. The necessary conditions of temperature are easily arranged for, but the required condition of pressure, 800 lb., is not so simple a matter. The company has been working on this problem, and at the refinery in Oklahoma work of this kind is now being carried on. The way in which an ordinary still will leak at 50 lb., and more at 100 lb., leaves some doubt in the mind of many as to what can be clone at a continuous working pressure of 800 lb. On the other hand, the fact that they are making ammonia abroad by a method which employs higher pressures and temperatures than anything involved in this method, leads me to believe that the difficulties, which will undoubtedly arise when this is attempted on a commercial scale, can be overcome. WILLIAM N. BEST, New York, N. Y.-Is there any change in the calorific value of these oils?

Jan 5, 1915

By John Griffen

K. F. Tromp (Kerkrade, Holland)—Your assumption that the Dutch State Mines have lead in the development of heavy medium processes—the Barvoys, Loess, Driessen—is not correct. The credit should be given to a Dutch engineer Mr. deVooys, the inventor of the Barvoys process. deVooys started in 1932 in Hiickelhoven, a German but Dutch-owned mine, where he was a director. Several plants on the Continent as well as in Great Britain were erected. The State Mines started their first plant in 1937. They could not get that plant working satisfactorily and built another one. Their process made no headway, and up to 1946 there was only one plant installed, the one at their own pit. Since 1946 they started the cyclone process and only since that time have they been more active, though industrial cyclone washeries are still in their infancy. deVooys sold his patents to the Dutch State Mines in 1946 and this might have given you the impression that the pioneer work had been done by the Dutch State Mines. John Griffen (author&apos;s reply)—I wish to thank Mr. Tromp for giving the correct story on the development of heavy medium processes in Holland.

Jan 1, 1952

By B. F. Oliver

Equilibrium and kinetic segregation coefficients for the dilute high-temperature system tantalum in iron have been experimentally determined in a levitating zone melter. The equilibrium segregation coefficient, ko, is 0.43 * 0.03. Planar interface solidification is possible up to a freezing velocity of 4 in. per hr but not at 6 in. per hr. Precise concentration control of the solid is possible over this range of freezing velocities. The momentum boundary layer thickness, and the diffusion boundary layer thickness, 6, are such that either 6, > 6 or ALTHOUGH considerable data exists in the literature concerning the stability of planar-solidification fronts, little data exists for high-temperature metallic systems. The study of fundamental aspects of solidification in high-temperature iron-base systems is complicated by the extensive solvent power of liquid iron. In order to minimize such effects a levitating zone melter was used to study the segregation of tantalum in iron.&apos; The solute tantalum was selected because: 1) the ko value was, according to the literature, initially thought to be less than 0.1, thus increasing the precision of the method used;2,3 2) the vapor pressure and is a constant, fixed by induction stirring, 6, the diffusion boundary layer, is 5150 u. At 400 rpm and 6 in. per hr freezing velocity the cast structure exhibits circular macroporosity and banding concentric with the axis of the rotation of the interface. Electron-beam microprobe analyses indicate that the tantalum content is highest at the center of rotation (1.2/1) and decreases with increasing radius as the fine-grained bands become sharper. This entire structure exhibits microseg-regation of tantalum. of tantalum in 1 atm of H2 is small, assuring conservation of solute during redistribution; and 3) spec-troscopic analyses were available for the appropriate range of tantalum considered. Additional objectives were 1) to determine kinetic segregation coefficients for well-stirred zones with constant boundary conditions and thus quantitatively calibrate solute-segregation behavior in the levitating zone melter, and 2) to examine the range of freezing velocities over which smooth solid-liquid interfaces could be controlled in an iron-base alloy under the restrictions of the thermal gradients imposed while levitating a zone. The single-pass zone-melting method was used to calculate individual k values.&apos;

Jan 1, 1964

By L. G. Huntley

Discussion of the paper of L. G. HUNTLEY,. presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 102, June, 1915, pp. 1333 to 1349. E. W. SHAW, Washington, D. C. (communication to the Secretary*). -The comparatively great extent and uniform character of the Dakota sandstone make it of great interest to the student of rock pores and the movements of their fluid contents. However, compared with other sands in areas of carbonaceous rocks facts concerning it do not seem to be of such great direct importance to the producer for it has thus far yielded few important pools of oil or gas. Information concerning the sandstone is extensive but scattered, hence a general treatise regarding it-particularly its pores, the fluids they contain, and the movements of the fluids-has been much needed. I therefore feel that the. chief thing to be ,desired concerning Mr. Huntley&apos;s paper is that it were more extended, particularly as to the discussion of the data presented. The general structure map of the Dakota is of especial interest. Slight changes in wording seem to be desirable here and there in the paper. For example, at the beginning of the third paragraph one-wonders if flora instead of fauna were not intended. In Figs. 2, 3, 4, and 5 the vertical scale seems incorrect. Concerning the analyses of oil quoted it is noted that they "are given, as indicating what may be expected in different localities." This seems to need modification for the average analysis of oil from Powder River, which indicates for example that this oil begins to boil at 213°C. The fact is that the samples to which this figure refers were taken from seeps long exposed. to the air :find hence the underground Dakota oil of this district no doubt differs profoundly from that which the analysis indicates. The product of a well here would probably differ more in boiling point and other. respects from the samples analyzed than it would from almost any other petroleum in the world. The use of the word synclinorium does not conform to the original definition, but this may be pardonable because misuse of the term, though a different misuse, has become general. Synclinorium is an orographic term and cannot be correctly applied outside of mountain regions, for it is derived in part from the Greek word for mountain. It has, however, been widely used in a purely structural sense for compound syncline. The broad shallow syncline of the Dakota sandstone falls in neither category. Objection might also be made to the use of

Jan 12, 1915

THE Institute assembled in the metallurgical lecture-room of Pardee Hall, Lafayette College, at 7 o&apos;clock P.M. on Tuesday evening, October 21st. The session was opened by the President, R. W. Raymond, with an address on Mining Industry as illustrated at the Vienna Exposition. The second session was held on Wednesday morning. The Council reported the following names for election as members and associates. They were unanimously elected. †Ayres, W. S., - Easton, Pa. *Baker, Prof. A. L., - Easton, Pa. †Browne, Thomas Nicholl, - Hamilton, Nev. *Carter, Frank, - Pottsville, Pa. *Davis, E. F. C., - Pottsville, Pa. *Fox, Prof. J. G., - Easton, Pa. *Haight, Ogden, - Etna, Pa. †Hall, Norman, - Sharon, Pa. *Knap, Joseph, - Fountain Mill, Pa. †Miller William McKeen, - Easton, Pa. †Pardee, I. P., - Easton, Pa. *Plater, John E., - Eureka, Nev. *Platt, Joseph L., Jr., - Franklin Furnace, N. J. *Plumb, W. H., - Mauch Chunk, Pa. *Reis, George L., - New Castle, Pa. *Samuel, Edward, - Philadelphia, Pa. *Smith, William Allen, - Trenton, N. J. *Smock, Prof. John C., - New Brunswick, N. J. *Weberling, Charles, - Salt Lake City, Utah. Also the following as foreign members Beaulieu, Ad. le Hardy de, - Brussels, Belgium.. Beaumont, Major Fred., - London, England. Beck, Alexander, - Mons, Belgium. Bodmer, J. J., - London, England. Brassert, Berghauptmann, Dr., - Bonn, Prussia. Brogden, James, - London, England * Members. † Associates.

Jan 1, 1874