Search Documents

By R. M. Bird

FEW persons outside of the foundry trade have any conception of the great variety of sands now regularly specified and furnished, nor of the differences in foundry practice frequently resulting from apparently minor changes in sands. Conditions in each locality where the sands are mined and prepared necessitate special equipment designed to perform the work efficiently. The description that follows of the foundry sand producing operations is typical of the areas in New York and New Jersey, and particularly refers to the operations of the George F. Pettinos Co.

Jan 1, 1926

By A. C. Dorenfeld

CHANGES in circuits are often made in milling operations. At the same time that these changes are being evaluated the ores are changing. Even from the same mine, the ore is usually variable as to amount and type of mineral content, degree of association of valuable and gangue minerals, amount and types of soluble salts, hardness, etc. The question then arises whether any small differences in results, after changes have been made in the various circuits, are really due to these changes or whether the variability of the ore can account for those differences. Statistical evaluation provides one method of answering the question that arises so often in beneficiation studies: Did changed results come about because of changed process, or did ore variation cause the change? In this case, data were available for statistical analysis from an operating period of 42 months, representing treatment of approximately 1 million tons of ore. During this period there had been two flowsheet changes: 1) regrind of the zinc circuit middlings was introduced, and 2) alcohol- pine oil frother mixture was substituted for cresylic acid-pine oil frother mixture. Findings are in Table I.

Jan 10, 1954

By Robert E. Sorenson

EXPLORATION for deep-seated orebodies in the Silver Belt area of the Coeur d'Alene mining district is complicated by meager surface expressions of diagnostic criteria, lack of knowledge of the significance of specific alteration phenomena, and the great expense involved in the exploration for ore shoots, the tops of which often occur near sea level elevation or below and as much as 4000 ft or more below the surface. Except for the early studies of Ransome and Calkins in 1903 and 1904,' little geological work was done in the Coeur d'Alene district for many years, and it is only during the last 15 to 20 years that complete and careful geological mapping has been applied to most of the mines in the area. Much early information, which now would prove invaluable, is lost in hundreds of miles of caved and inaccessible mine openings not mapped by mining geologists. In more recent years mining geology has become a tool of greater use in the district, and some measurable progress is being made in the accumulation of observations that are adding gradually to the knowledge of ore deposits in the district. The recognition of alteration phenomena and related features by Hoyt S. Gale3 in 1935, followed by the work of Shenon and McConnel in 1936-37,4 changed many of the concepts formerly held and opened the way for more critical study and mapping of alteration effects. Mapping of these effects has been in progress for several years but no well-organized, careful, and complete laboratory study of the alteration has been made by mining companies or by government agencies. Recently, Thomas Mitcham of Columbia University has been occupied in the collection and study of specimens carefully selected from several producing mines in the Silver Belt as well as from several prospects exhibiting alteration effects. Mr. Mitcham and the writer have discussed some of the preliminary results of his investigations, which indicate that definite and interesting material is forthcoming from his studies. Work of this kind, aided by careful observation by district geologists, should advance the knowledge of the environment of Silver Belt ore shoots and establish additional criteria for recognizing meager shallow expressions of deep-lying orebodies. Structural details in the Silver Belt area are extremely difficult to decipher on the surface because the area is almost completely covered by a deep mantle of surface debris and soil. A dense growth of small trees and buck brush adds to a geologist's difficulties. Often large areas reveal only scattered small outcrops with great intervening areas where the underlying formations must be deduced from small altered rock fragments. Some considerable success in obtaining surface information has come from bulldozer roads and cuts in selected areas. As this type of work receives more attention, knowledge of the surface expressions of formations, alterations, faulting, and veining is expanding and giving more reliable information to guide deeper development. Lack of diagnostic marker beds in the district contributes to a geologist's difficulties in determining fault displacements. In the Silver Belt, known commercally important sulphide orebodies commonly are associated with siderite and quartz gangue. Some of the veins at shallow horizons above productive ore shoots are composed of quartz with light-colored carbonate minerals such as calcite, ferrocalcite, ferrodolomite, ankerite, and carbonates with variable amounts of manganese. The relation of these carbonates to commercial orebodies is a problem offering possibilities for research. Shallow exposures of veins composed of quartz and the light-colored carbonates, often with some associated barite, grade into quartz and siderite veins at deeper horizons. The vertical range of these carbonates has been partially established for some veins, but no reliable method has been devised for predicting where the change in a vein may take place. Careful observation and analysis of carbonates may make it possible to predict more closely where the change to siderite may be expected. In 1926 Shannon5 pointed out some of the characteristics of the carbonate veins of the district and included a few chemical analyses. Some of the Silver Belt ore shoots have small commercial outcrops, and very shallow development of some properties has led to the opening of small ore shoots." Several small ore shoots developed at shallow depths have not been explored at deep horizons, and some important ore shoots with no commercially significant exposures at shallow horizons have been developed. The greatest problem of the mining geologist working in the Silver Belt area is to find the all-important link between the very meager shallow expressions of mineralization and the rich ore shoots that may be found below. To develop criteria for use in the recognition of the weak upper expression of ore shoots, the experience of past development programs must be relied upon heavily. The investment of more than a million dollars in the exploration for such ore shoots requires some reliable criteria if these ore shoots are to be found. Management needs some assurance that the risk involved is justified by well-developed and acceptable geological inference. The richness of some of the ore shoots found thus far has contributed greatly to the justification for a bold approach, but many negative results of blind exploration programs would lead eventually to extreme caution on the part of management. Fortunately, recent experiences of development programs have been quite successful. It is hoped that added knowledge. of the environment of Silver Belt ore shoots will contribute greatly to the sureness of approach toward their development. The Coeur d'Alene mining district is located in the panhandle of Idaho in Shoshone County. The population of the county is either employed in the

Jan 1, 1952

By Thomas B. Douglas

INSTRUMENTATION in the process industries can no longer be regarded as a convenience, but rather an absolute necessity. Although many chemical processes must already be conducted with instruments, every properly designed application of automatic process control will improve operation: 1) the product will be more uniform and of higher quality; 2) the manual labor saved will reduce cost; 3) uniformity of flow and uniform control of process will increase production; and 4) surges will be eliminated, making it possible to operate equipment near ultimate capacity at all times. Industrial instruments fall into two general classifications—those that measure and those that measure and control. The cement industry has been using instruments for a number of years, particularly in the burning process, primarily for indicatlng and recording. Automatic process control makes additional use of these instruments, and others, to control variables. Assisted by the instrument manufacturers, engineers at Ideal Cement Co. achieved considerable progress in determining how well the usual recording instruments could be made to control various phases of cement-making. The results of these experiments were used to make the new plant at Houston as wholly automatic as possible. The original Houston plant, built in 1937 by Gulf Portland Cement Co., consisted of only one 8 x 220-ft kiln and the necessary grinding mills and accessory equipment and had a capacity of 900 bbl per day (300,000 bbl annually). Ideal Cement Co. purchased this plant in 1940 and almost immediately started plans to increase its production. In 1941 a 9 x 220-ft kiln was installed and grinding and storage capacity were increased. The growing demand for cement in the Houston area necessitated a third kiln (9 ft 6 in. x 250 ft) in 1947. This brought the plant up to its present capacity of about 1.3 million bbl per year. Calcium silicates in cement are produced in a burning operation at high temperatures from raw mix of argillaceous and calcareous materials that have been crushed, mixed, and ground to a fine powder. The composition of this mixture must be kept consistent within narrow limits. Raw mixing and grinding may be done either wet or dry, but in both instances the materials must be correctly proportioned, finely ground, and thoroughly intermixed before entering the kiln. As the raw mix passes through a long horizontal rotary

Jan 1, 1959

By H. Merton Ruth

THE northern anthracite fields, although facing the same economic problems as the southern fields, are confronted with the additional problem of fast dwindling reserves of anthracite which can be conventionally and economically won. The mining of coal which remains in thin beds and the recovery of pillars from areas heretofore considered unrecoverable, either by reason of cost or surface restriction, pose problems of in- creasing importance to the economic life of the northern field operations. Successful approaches have Been made to this problem and other work is being performed that holds promise. There exists in the northern anthracite field millions of tons of solid coal, the recovery of which has not been too successful due to the following inherent operating faults: inability to concentrate producing areas; the great quantities of rock to be cut and handled, lack of consideration of proper sequence and speed of second mining, and the continued use of the mine car as the basis of payment. A mining system that has successfully solved these major problems has been in operation in the Scranton area since 1944. Over 1% million tons have been produced from veins varying from 3 to 4% ft thick by this method, which is known as the multiple panel-triangular system-conveyor mining.

Jan 1, 1950

By K. C. Ko, D. A. Pifer

The theory of probability with respect to the failure of structures is discussed. It is shown that the probability of safety, probability of failure, and factor of safety are directly related to each other and that as standard deviation approaches zero, the probability curves approach a unit step function which can be interpreted as the conventional factor of safety. The factor of safety is numerically the ratio of the load to the strength of the material at a particular point or plane in an engineering structure. Mathematically, it can be illustrated as a unit step function undefined at the point where the factor of safety is one (Fig. 1). The uncertainty of variation of soil and rock strengths require factors of safety much higher than those used in other engineering structures. The factors of safety used are generally determined from past experiences with similar structures. However, the factors thus determined do not have any theoretical meaning or do not indicate any relationship to actual safety.' It seems, therefore, logical to develop a system with a sound theoretical basis to obtain a more suitable factor of safety for structures. An application of elementary theory of probability indicates that it is possible to relate this number to theoretical and practical engineering facts.

Jan 1, 1971

By F. L. Bosqui, A. D. Wilkinson

EVEN though the world has not been crying for more copper for the last three or four years there has been some important mill and smelter construction. Discovery and development of large new high-grade copper deposits in Africa has led to the construction of extensive reduction facilities there, prominent among which is the concentrator and smelter of the Rhokana Corporation at N'Kana. Northern Rhodesia. The 3000-ton concentrator adjoins the central shaft. A little over half a mile to the southeast, at an altitude of 40,010 ft., is the smelter, designed on the site by 1. H. Wynne. It is arranged primarily to treat N'Kana copper concentrates, but can also handle concentrates and direct-smelting ore from outside sources. Excavations were started late in 1930; concrete was first poured on Jan. 6. 1931; and the first blister cop¬per was cast on March 1.9, 1932, less than fifteen months later. During this period, which included several months of heavy tropical rains, some 10,000 cu. yd. of concrete was poured and 41000 tons of structural steel erected under the supervision of construction engineer, A. Ek, with a labor force of 60 to 30 Europeans and about 300 natives. The steelwork was fabricated by Head Wrightson & Co. in England, and the boiler plant equipment furnished and erected by the International Combustion Co. Ltd.

Jan 1, 1934

In the Bowen Basin of central Queensland, coal production has gone from virtually nothing in 1961 to more than 24 million tons today4ut there's a cloud over this success.

Jan 1, 1977

By M. Felsenthal

Engineers are frequently faced with the problem of having to predict oil recovery from a solution gas drive reservoir in the early life of a field. This is often the time when actual laboratory or field-derived gas-oil permeability (kg/k0) data are not yet available. Although excellent collections of k0/k0 data for various types of rocks may be found in the literature,1,2,3 a need exists for a more detailed correlation of k0/k0 data with core properties such as porosity, permeability, clay content or pore-size distribution. It is the purpose of this article to present this type of correlation for sandstone material. The correlation is based on laboratory tests performed on over 300 core samples from 19 reservoirs in the United States and Canada. EXPERIMENTAL Cores were analyzed by routine procedures, using samples of conventional size (7/8-in. diameter, 7/8-in long) cut parallel to the bedding planes. Air permeability was measured at 1.67 atm mean pressure in a Hassler-type apparatus. Porosity was determined with the aid of a Ruska bulk volume meter and a Boyle's Law rock volume meter, An evaporation method' was used to evaluate irreducible water saturations. Core samples were saturated with 25,000 ppm NaCl brine. The brine was reduced to the irreducible saturation, and the remainder of the pore space was filled with kerosene. This was followed by multiphase flow tests using the so-called "dispersed feed" technique.5 n this technique, gas and oil (kerosene and kerosene-saturated air) were dispersed with the aid of a porous Alun-durn feed head, the face of which contained a waffle-shaped system of Lucite-lined grooves. Oil entered the back side of the feed head and emerged at the raised areas of the front face. Gas was introduced directly into the system of grooves at the front face. The gas-oil mixture then entered the test core which was kept in capillary contact with the feed head. Permeabilities were determined from rate and pressure measurements and saturations from weights. All determinations were performed at equilibrium or steady-state conditions. Pore-size distributions were determined on selected samples by a mercury injection technique.6 GENERAL CORRELATIVE TRENDS When examining data from a given reservoir, it was noted that k0/k0 vs saturation curves became generally less steep as specific air permeability increased, a development that has a favorable effect on oil displacement efficiency by solution gas drive. This trend has also been reported by others in the literature.' An effect of porosity on k0/k0 data was also noted. This effect was not generally discernible in a study of relative permeability data for a given reservoir but became apparent when data for sandstone reservoirs of similar lithology but differing average porosity were compared. For instance, in a comparison of argillaceous and/or calcareous sandstones from 11 reservoirs ranging in average porosities from 14 to 28 per cent, a definite trend was noted, indicating that for a given permeability k0/k0 curves became less favorable (i.e., steeper) as porosity increased. A similar trend was observed for a group of comparatively clean sandstones from five reservoirs ranging in average porosities from 15 to 21 per cent. For a given permeability and porosity, comparatively clean sandstones gave more favorable k0/k0 curves than argillaceous and/or calcareous sandstone or chert reservoirs. The laboratory studies also showed that least favorable k0/k0 curves were exhibited by shaly sandstone, conglomerate, and sandstone containing carbon inclusions. Table 1 lists the various source reservoirs classified by lithology types. To facilitate a correlation of k0/k0 data with core characteristcis, it was found expedient to work with

By Morris M. Fine, Norwood B. Melcher

It is out of the question, at this time, to select any one prereduction process as superior to the others. It is apparent that several share a basic similarity and that within the groups listed in Part 1, the reduction vessel is sometimes the only significant variable. Claims as to the virtues of one machine over another are difficult to substantiate: one may be rapid, another thermally frugal. Based on published data, however, all seem to be performing adequately. It would appear that processes based on carbonized pellets are most applicable to foundry iron at low production rates. Adaptation to large scale manufacture of blast furnace hot metal or to agglomeration of fine concentrates at the mine site is much less likely.

Jan 8, 1966

By Herbert Hoover

DURING the year, the' Institute has made the most remarkable growth in its history. Our actual increase in membership was 1816 and therefore was 80 per cent. larger than any previous year. Even without expectation of any abnormal growth, we should pass in the year 1921 the 10;000 mark. The causes of this increased growth are not far to seek.. They lie in the widening vision of the Institute's work, not only in its relation to' the profession but as an avenue of service to the nation as a whole. The Institute is today in the first rank of influence among public institutions in the country. During this year we have, for the first time in many years, had a ?deficit of some $3000 in our finances. The sum is not important, but it- does indicate the tendency of the times, and that is the high cost of living:' The increase in our expenses lay, to the largest degree, on the publishing side of the Institute's work. If we compare the year 1918, as a fairly repre¬sentative year, with that of 1920, we find that the costs of issuing the' Institute's publications, after deducting the income received from these publications, shows a .net increase of about $33,000. for the year. This has been to some degree due to the enlarged membership but to a large degree due to the cost of the paper and printing.

Jan 1, 1921

By B. C. Wonsiewicz, W. W. Wilkening

Following a procedure proposed by Wheeler and Ireland, Plane stress yield loci were constructed from Knoob hardness numbers. Basically, six differently oriented hardness measurements were made on three orthogml surfaces through pure poly crystalline magnesium sheet, a magnesium single crystal, and sheet of the magnesium alloys: Mg + 0.5 pct Th, Mg + 4 pct Li, AZ31B, and EKOO. Hardness loci were found to be in poor agreement at small strains (E < 0.05) with loci established by a more rigorous technique. At larger strains (E - 0.10) the agreement is fair, but at this stage in deformation the conventional locus has lost much of the asymmetry that characterizes these anisotropic materials. Two effects which will lead to distortions in the Khn locus are discussed with reference to the geometry of plastic flow during a hardness test. DETERMINING a material&apos;s resistance to multiaxial loading is of interest not only from a structural design viewpoint but also from that of deformation processing. Unfortunately, the determination of the yield locus, although simple in principle, involves tedious procedures if the results are to be at all rigorous.&apos; The idea, first proposed by Wheeler and 1reland2 of determining the yield locus by means of six Knoop hardness impressions along the principal directions in a material has obvious appeal. It is simple, quick, and should be applicable to very thin sheets. If such a technique could be demonstrated to produce consistently reliable results, it would be of interest to both researcher and designer. Lee, Jabara, and ackofen have compared the yield locus determined by Knoop hardness measurements (the Khn locus) to a locus determined by more rigorous techniques. They found good agreement for two titanium alloys at a plastic strain of about 1 pct. The purpose of this paper is to investigate if the Khn locus construction is a reasonable approximation to the locus of a highly anisotropic material. Examples of such materials are magnesium and magnesium alloys which have severely distorted yield loci which in turn reflect markedly dfferent yield strength in different directions.&apos; In pure magnesium, for example, the yield stress in tension along the transverse direction may be four times the yield stress in compression in the same direction and twice the tensile yield stress in the rolling direction. Predicting such large differences ought to serve as a severe test of the Khn locus construction. EXPERIMENTAL PROCEDURES Samples of rolled sheet, 0.250 in. (6.35 mm) thick, of pure magnesium and four magnesium alloys (Mg experimental materials. The pure magnesium together with the lithium and thorium alloys were those used in the study of Kelley and Hosford. The grain size was ASTM number 4 for the pure magnesium and number 6 for the alloys. HARDNESS TESTING The materials were sectioned along the rolling and transverse planes, mounted in a quick setting resin, and mechanically polished. Most of the hardness tests were performed on a surface prepared by electro-polishing (30 pct nitric acid in methanol at 0°C and 20 v) with the exception of the AZ31B and EK00 alloys which were made directly on a metallographically polished surface. However, subsequent hardness tests on the same sample after heavily electropolishing, revealed essentially the same hardness as before. At least twenty Knoop hardness impressions under a 100-g load were made in each of the six orientations shown in Fig. 1. The average hardness number and standard deviation were then calculated for each orientation. CONVENTIONAL LOCUS CONSTRUCTION Yield loci were constructed using a technique described in detail by Lee and ackofen,&apos; in which the flow stress (stress at a given plastic strain) fixes the coordinates of a point on the locus and measurements of the strain ratio serve to establish the slope of the locus at that point. The loading paths which correspond to uniaxial tension or compression tests establish the four intercepts of the locus with the coordinate axes plus one point on the balanced biaxial tension line Tensile testing was performed along the rolling and transverse (r, t) directions. Samples had a uniform rectangular gage length 1 by 4 by 4 in. (25.4 by 6.35 by 6.35 mm) and were deformed at a strain rate of 3.33 x 104 sec-&apos;. The tests were interrupted periodically to unload the sample and measure the plastic strains by means of X-Y post yield strain gages. Compression tests in the rolling, transverse, and through-thickness (r, f, z) directions were performed on 1/4 in. (6.35 mm) cubes at an initial strain rate of 8.33 x sec-&apos;. Lubrication was provided by 0.002 in. (51 pm) Teflon sheet which was renewed after unloading for micrometer measurements used to calculate the strains.

Jan 1, 1970

By James R. Finlay

SOMETIMES the American Institute of Mining and Metallurgical Engineers appears to be a strictly technical society, and if so my paper should deal with the technical operations of finding and producing gold. But I have not been engaged in practical gold mining since 1910. What I have been doing mainly for the last 25 years is to try to figure out what the income of a mine-gold, or any other-would be worth to an investor. So I have been in contact with gold mining, in one way or another, for some 42 years. I say that with a purpose. In that time the industry has been through one of its cycles. The value of gold mines is very dif¬ferent at different points in one of these cycles. For this reason the cycle of gold mining is a highly practical study. The cycle of gold is a more or less rhythmical change in its value or purchasing power measured in the grand average of other commodities, which is the same thing as its price. Taking the price of gold in 1897 as a stand¬ard, a dollar at that time declined to 55c. in 1913, to 26.8c. in 1920, and since then it has risen to 47.4c. in 1930 and to about 64c. in 1932. It is worth about 21/ times as much now as it was in 1920, but less than two¬thirds as much as in 1897. When this change is applied to the value of a gold mine still greater differences are evident. The cost of producing gold is of course measured in labor and other commodities, and as that cost goes down the margin of profit measured in the gold itself increases. Thus a mine which might make only 10 per cent profit in 1920 on its gross output may easily make 25 per cent now. The stockholder gets 2 ½ times more gold that is worth 2 1/2 times as much in purchasing power, therefore the real value of his holding has risen by the one factor multiplied by the other, giving him 61/4 times as much goods or services as he had in 1920.

Jan 1, 1933

By John J. Stokes

Literature on the electrolysis of aluminum from cryolite melts and on the structure of these .melts is surveyed critically. Data on density, freezing point, and other properties are reviewed. Theories of the electrolysis are examined in the light of these data. Two theories are presented which account equally well for the observations. In the early days, the process was thought of as a simple one. The actual mechanisms must be tremendously more complex. This paper is devoted to a rather narrow part of the whole subject, namely, what ions are present in the bath, and by what mechanism the current is carried. Using cryoscopic data, Rolin has determined the following composition for molten cryolite. Na2,AlF 3Na + 3F + AlF [1] He postulates the following equation for the ioniza-tion of alumina at low concentrations Al2O3 Al + AlO2 +O. [2] At concentrations above 0.025M he supposes the ionization of alumina to proceed as follows Al2O3 AlO + AlO2. [3] Rolin&apos;s mechanism of electrolysis for the more concentrated solution in Eq. 3 is as follows. The AlO&apos; ion migrates to the cathode. where it is dis- charged, giving metallic aluminum and 0&apos; ions which migrate to the anode. The AlO2- ion migrates to the anode, where it is discharged, giving Al ions and oxygen which reacts with carbon to form CO2 In the case of the extremely dilute solution in Eq. 2 the Al ion migrates to the cathode and the AlO2-and 0 migrate to the anode as before. Another possible mechanism for the electrolysis follows. Ionization of Cryolite Na3AlF4 = 2Na + 2F + NaAlF, Na + AlF-AlF+Na + F [4] Addition of Alumina 2Na2AlF+ 2AL2O4 6Na + 3A12O3F4 [5a] Al2O2F 2AlOF2 [5b] Cathode Process AlF, + 3e+ 4F + Al. [6] Anode Process AlOF2 + 2F AlF1 + 1/20, + 2e or A12O2F + 4F-2A1F; + 0, + 4e. [7] Although both Rolin&apos;s and the present mechanism of the Hall process may be qualitatively satisfactory, present data are not adequate for quantitative tests of the theories.

Jan 1, 1959

By A. C. Stevenson

IN OUTLINING the various steps taken and the exigences met during the time of unwatering and rebuilding the burnt top equipment at the Hecla mine, the major portion of the detail is omitted and a general description of the experience only is given. All the electrical power lines were out of commission, as were the mine feeder cables. The first effort, there- fore, was to restore electrical connections. The Washington Water Power Co. immediately put a crew to work restoring the power line, it being necessary to rebuild about 4000 ft. of 66,000 volt transmission and about 2000 ft. of 2200 volt feeder. This work was rushed and power was again available at the mine sub- station about 26 hours after the fire. During the same time temporary lighting lines were strung and transformer equipment obtained, so that when electrical connection was resumed the lights were turned on and the dump well lighted that night.

Jan 1, 1924

By CHARLES DORRANGE

INTRODUCTION. CULM is a general term used in the anthracite regions for many years to denote a mixture of coal, bony coal and impurities which is sent to the refuse-banks. Thus, 35 years ago culm contained the pea and buckwheat sizes of anthracite; but to-day, and as mentioned in this paper, culm is used specifically to denote the material which passes through the smallest screen in the anthracite-breaker. The smallest size of commercial anthracite is known as No. 3 buckwheat, barley, or bird&apos;s-eye coal, and is ordinarily made through a round-punched plate having openings 3/16 in. in diameter, and over a round-punched plate with opening 3/32 in. or 1/16 in. in diameter. Thus culm will consist of coal, bony coal, slate, gravel, iron pyrite, etc., ranging in size from ? 3/32 in. down to dust. Other local terms for culm are " slush," " silt," and " dirt." The first experiments towards the utilization of anthracite culm by briquetting, and the first briquetting-work done in this country, were in 1872 at Port Richmond Piers, Philadelphia, Pa., by E. F., Loiseau.1 Clay was used as a binder and the finished briquette was water-proofed with shellac, etc. Excessive cost was given as the reason for discontinuing work at this plant. The Delaware k Hudson Co., in 1876, built a plant at Rondout, N. Y., which operated until 1880. Gas-tar was used as a binder, and anthracite screenings were briquetted for engine fuel. Excessive cost, poor results in firing, and the tendency of the fuel to cut the boiler-flues were given as the reasons for discontinuing the manufacture. The next plant was built by E. F. Loiseau about 1878, at Nesquehoning, Pa., near the No. 1 or Nesquehoning colliery

Sep 1, 1911

By Prince Lazarovich, Hrebelianovich

I WAS asked by the chairman of one of the Sessions on Employment Problems to talk about the viewpoint of the foreign workingman. I am not a workingman. I have never done what a work-hand might call an honest day&apos;s labor; that is, I have never been in a factory or manufacturing plant or in a mine, though in truth, hard work and I are well acquainted. I was a soldier, am an engineer, have long been actively interested in the most important waterway construction in the near East, have served politics and diplomacy, written books and lectured at universities. My knowledge of the foreign workingman in this country comes from the fact that my own compatriots here at various times came to me and appealed for advice and help, and last year I was asked by the employment manager of a corporation to undertake a welfare job at one of their plants. I went out, saw the plant, talked with the superintendent and outlined certain of my ideas which he personally heartily approved, but which did not find favor with those higher up. I approach the subject of the foreign workman&apos;s point of view with the understanding that the industrial employer&apos;s effort is for the maximum of efficiency. I am conversant with labor conditions abroad both in industry and agriculture. What I have learned of industrial conditions in America as they affect the foreign immigrant has been chiefly gathered from the cases referred to of foreign workmen who from time to time have come to me with their troubles. In the course of those investigations, in order to give whatever help or advice was possible, I have been impressed with the fact that the great United States industries evidently had- pot yet sufficiently recognized the value of studying the conditions of the workingman in the lands of his origin across the seas. A careful study of that which could be called the moral element in connection with its foreign labor would give industry a knowledge of the man&apos;s reason for coming, what&apos; grievances he brings with him, his hopes for a future, and the peculiar character of his capacities. The employer would thereby be enabled to meet the man, to be helpful to him, to aid him and at the same time promote industrial efficiency, inasmuch as a workman who believes that he is being dealt with humanly and squarely is contented and satisfied and will give willingly, and even with pride, the best that is in him; justice and a fair deal is all the man wants.

Jan 4, 1918

By R. D. Pehlke, J. V. Gluck

AS a portion of a general study of liquid-metal thermodynamics, high-temperature galvanic cells were used to study the effect of added dilute solutes on the activity of zinc in dilute solution with molten bismuth in the range 450° to 650°C. 1,2 The cells were of the type The experimental procedures have been described previously.1 In the course of studies conducted in the bismuth-rich corner of the systems Bi-Zn-Au and Bi-Zn-Cu, marked discontinuities were observed in the electromotive force-temperature relations for a number of the experimental compositions. Above the discontinuity temperatures, the relations, which were linear, exhibited slopes similar to the binary alloy of the same mole fraction zinc, as shown in Figs. I and 2. Below the discontinuity temperatures, the slopes were markedly different, but the relations remained linear. In general, as the amount of the third eletnent was increased, the slope of the lower portion of the relations tended to become less positive. The slopes of electromotive force-temperature relations reflect the entropy of mixing of zinc and, therefore, the occurrence of a discontinuity marks the transition between two different equilibrium situations involving the solution of zinc. A number of other investigators3-5 have used such observations to determine liquidus boundaries in binary alloys. Since the upper portions of the ternary electromotive force-temperature relations of this study had the same slopes as the binary alloys, the discontinuities are interpreted as marking the transition between the single-phase liquid region and the underlying two- and three-phase regions. Reference to the Zn-Bi equilibrium diagram6 confirms that the binary alloys were single-phase liquids at the experimental temperatures. Fig. I shows the electromotive force-temperature relations for the alloys containing Bi-Zn-Au and Fig. 2 shows similar relations for the Bi-Zn-Cu alloys. In the lower portion of each figure, the temperature of the discontinuity is plotted vs the mole fraction of the added solute at the various levels of zinc concentra- tion. Cross-plots from these curves at constant temperature permitted the construction of the partial liquidus surface isotherms shown in Figs. 3 and 4.

Jan 1, 1967

By Charles E. Locke

DEPRESSION in all lines of the mineral industry except gold, which began in 1930 and continued, even worse, through 1931, had its effect on ore concentration. Construction was limited to the completion of plants already begun. Every possible economy was adopted. Changes and improvements involving expense were postponed. Research was largely abandoned. Operations became highly efficient and costs were cut down, although this did not necessarily mean a lower cost per ton because of the greatly reduced capacity at which mills were run. Lower metal prices caused the operators to seek the optimum ratio of concentration and grade of concentrates looking toward maximum economic recovery; that is, net profit. In the crushing field no marked changes occurred. The Symons cone crusher for intermediate work is in use almost everywhere. Its manufacturers claim that 900 machines have been installed in 21 countries, replacing two previous steps of crushing and yielding a product sufficiently fine to form a satisfactory feed for rod mills and ball mills. A new Telsmith crusher has appeared which has curved jaws something like the Symons cone and consequently the same advantage as the latter.

Jan 1, 1932

By H. M. Chance

Jan 1, 1886