Search Documents

By AIME AIME

THE 131st meeting of the American Institute of Mining and Metallurgical Engineers was held in New York on Feb. 16 to 20, 1925, with the largest registration of any previous meeting, the total being 1320 compared to 1276 in 1924. The technical sessions were more largely attended and aroused more discussion than ever before. There were joint meetings with the Mining Section of the National Safety Council, under the auspices of the Industrial Relations Committee of the Institute and two very important lectures, the Howe Memorial Lecture, under the auspices of the Iron and Steel Committee, and the lecture by Dr. Carl Benedicks, of Sweden, on Corrosion, under the auspices of the Institute of Metals Division. The Petroleum Division conducted its annual Symposium on Oil which will be published later in book form. At the annual business meeting on Feb. 17, the following ticket was elected, and the reports of the President, Treasurer, and Secretary 'were presented:

Jan 1, 1925

By H. A. Wriedt

At 500°C (932°F) the range of y' iron nitride is from 5. 77 + 0.03 wt pct N (in coexistence with a iron) to 5.88 * 0.03 wt pct N (in coexistence with E iron nitride). Stoichiometric "Fe,N" (5.900 wt pct N) is near the upper extreme of possible compositiom. The depe-dence of nitrogen activity (expressed as pnh,/Ph,) on nitrogen content is described satisfactorily by a "Langmuir" isotherm: At even the highest nitrogen concentrations, less than 0.18 pct of' the nitrogen atoms present are impositions of disorder. Past investigations1-4 of the Fe-N system have left only details of the thermodynamic behavior of the y' nitride, "Fe,N9', to be studied. The present investigation was made to establish more precisely than hitherto the limits of composition and the relation between composition and nitrogen activity at 500°C. EXPERIMENTAL TECHNIQUE The compositions of nitrides in equilibrium with various NH, + Hz mixtures at 500°C were determined from the weights gained by 0.02-in.-thick (4.0 to 4.5 g) strips of purified iron* when the nitrides were formed A description of the gas generation and furnace system has been published.5 Cracking and blistering during conversion of the original solid iron at 550°C injected considerable porosity into the strips without causing their disintegration. The time for complete conversion was significantly lowered by periodically reducing partly nitrided specimens in hydrogen and then reexposing them to the nitriding gas. Gas mixtures producing single-phase were used in the equilibrations at 500°C. Equilibrium was regarded as existing when the specimen weight was not detect-ably affected by further exposure to the same conditions. The gas compositions and nitrogen activities at which y' transformed to a iron (lower activity limit) and to E iron nitride (upper activity limit) were redetermined during the investigation. A specimen was equilibrated in an NH, + Hz mixture at 500°C and then exposed to a s1ightly different gas. When equi- librium had been reestablished the gas was again changed slightly. At each stage of this repeated process, while the specimen was reacting with the gas, the variation of its weight with time was observed. The onset of phase transition was marked by an abrupt change in the amount and rate of weight gain or loss. The specimens were weighed outside the furnace, in air and at room temperature, on a balance with 0.05 mg precision. When it was found that the specimens were oxidizing at a significant rate during the weighing, a series of timed weighings was made with each specimen, starting 1 min after its exposure to air. RESULTS AND ANALYSIS The gain in specimen weight from oxidation during weighing was linear in the logarithm of time between 1 min and about 2 hr, Fig. 1, later becoming linear in the cube root of time. In the logarithmic period, nitride specimens oxidized two to three times as fast as

Jan 1, 1970

By J. M. Smith, D. Kunii, P. Adivarahan

Effective thermal conductivities were measured for seven samples of porous rocks through which gases or aqueous salt solution were flowing, parallel and countercurrent to the flow of heat. The results are analyzed in terms of the contributions of the solid and fluid phases to the total energy transfer. The solid contribution for the sandstone samples studied was found to be a Junction of the porosity and an effective thermal conductivity for the solid phase. The fluid contribution was a function of the Peclet number. Based upon the equations presented, the effective conductivity of the system can be estimated from the properties of the fluid, the flow conditions, and the porosity and pore-size distribution of the rock. INTRODUCTION Heat-transfer characteristics of porous media containing fluids are needed for the design and evaluation of thermal methods of petroleum production. The study reported here considers the problem of countercurrent flow of fluid and heat in sandstone rocks, and is a continuation of previous studies concerned with parallel and radial flow of energy and fluid in both rocks517 and beds of fine particles.6,10 In addition to these earlier works, Asaad,1 Kimura,4 Preston,8 Zierfuss and vlietll and waddams9 have reported effective conductivities for systems filled with stagnant fluids. There appears to be no published data on rocks through which fluids are flowing. The purpose of this study was to present such information and, particularly, to investigate the effects of properties of the rock and the flow rate on the results. The rock samples were naturally occurring sandstones from different locations and were similar to petroleum-bearing formations. The properties of the seven samples showing the range in porosities and permeabilities are given in Table 1. The mean pore sizes were calculated from mercury penetration data by averaging the radius with respect to pore volume. The details of this method and comparison with other procedures for estimating 7 are given elsewhere. Four fluids, nitrogen, carbon dioxide, helium and 10 weight per cent sodium-chloride solution were used with each sample. For Bartlesville sandstone, BA-5, runs were made at mean pressures from 15 to 250 psig using nitrogen. The other measurements were carried out at a mean pressure of 100 psig. The maximum temperature range eacountered was 70° to 300°F. The flow rate of fluid ranged from about 1.0 to 130 Ib/(hr)(sq ft), and this corresponded to a modified Reynolds-number range of 5 x 10-4 to 1.0. The variation in Prandtl number was 0.70 to 4.1. EXPERIMENTAL WORK The equipment consisted of apparatus to supply a constant flow of gas, or salt solution, at constant pressure to the bottom of a vertical test section, and metering and flow-regulation apparatus after the test section. The flow of salt solution was

By Raymond E. Byler

THE challenge of unprecedented need for more metals to meet present-day re-armament and domestic requirements is being met with minerals beneficiation projects of great number and variety, and with new and improved methods, techniques, and. equipment. Iron Range Developments Much attention has been given during the year to the tremendous program for beneficiation of taconites and intermediate iron ores which is progressing through large pilot-plant tests preparatory to full-scale production operations. The greatest activity has been directed toward concentration of magnetic taconites on the Mesabi Range. The Reserve Mining Co. has let $75 million in construction contracts for the 2 ½ million-ton-per-yr project (concentrates) at Beaver Bay, Minn., and is building a 300,000-ton-per-yr pilot plant to prove up the magnetic separation and pelletizing operations. Oliver Iron Mining Co. has a pilot plant under construction near Mountain Iron for concentrating magnetic taconites, and is operating experimentally a sintering and nodulizing plant on fine ore screenings and concentrates at Virginia to fully develop agglomeration technique. The Erie Mining Co. plant at Aurora continues its production of concentrates from magnetic taconites which was begun three years ago. No plans have been announced to treat the Mesabi Range nonmagnetic taconites, but F. D. Devaney, Pickands Mather and Co., is studying a new process for magnetically roasting lean ores to make them amenable to low-intensity magnetic concentration. W. R. Van Slyke, Cleveland-Cliffs Iron Co., calls attention to several noteworthy developments in the field of intermediate ores, perhaps the most significant of which has been the first commercial operation of a Dutch State Mines (DSM) cyclone plant at the Buckeye mine of the M. A. Hanna Co. The plant concentrates the +1/4 in. fraction by means of conventional heavy-media treatment after suitable crushing, screening, and washing. The -1/4 in. +65 mesh material is treated in two 12-in. cyclones, the -65 mesh fraction being sent to tailing storage. The plant is operating successfully on feed rates up to 120 tons per hr, and indicates that successful treatment of the fine fractions of Mesabi intermediate ores is imminent. Another commercial-size DSM plant was placed in operation late in the year by Cleveland-Cliffs at the Holman mine, and two additional ones are expected to be in operation next year. Various other methods are also in use at different plants for treatment of the fine fractions, including classification, abrasion milling followed by classification, jigging, and Humphrey spirals. Where it can be economically justified, it seems at present that heavy-media treatment of the -1/4 in. fine fraction will also come into increasing use on the intermediate ores. During 1951 a one-unit, heavy-media plant to treat hematitic crude ore was erected at the Ohio mine on the Marquette Range by Cleveland-Cliffs and plans for another plant at Humboldt to produce 2000 tons of concentrates annually is contemplated, as is also the construction of a plant for agglomera-

Jan 1, 1952

By C. H. Stein

The Pennsylvania Legislature, on March 13, 1837, passed an act authorizing the Lehigh Coal & Navigation Co. to construct a railway to connect the North Branch Division of the Pennsylvania Canal with the slack water navigation of the Lehigh River; the navigation company accepted this act on May 10, 1837. Edwin A. Douglas, chief engineer for the navigation company, located the route for this railway from White Haven to Wilkes-Barre, which was called the Lehigh & Susquehanna Railroad. The object was to transport coal from the Wyoming Valley, of Pennsylvania, to the Atlantic seaboard. This railway was considered a marvelous piece of engineering, as it included a tunnel nearly 55 mi. long, and a series of inclines, or planes, up which the cars laden with coal were raised from the vicinity of Ashley to the summit of the mountain near Solomon's Gap, whence they were taken to White Haven by rail. There the coal was transferred to canal boats. In June, 1862, floods almost completely destroyed the upper division of the canal, so on March 4, 1863, the Pennsylvania Legislature passed an act prohibiting its restoration, but granted a charter for the construction of a railway from White Haven to Mauch Chunk to connect with the line from White Haven to Wilkes-Barre, previously built. On March 16, 1864, a supplementary act was passed extending the Lehigh & Susquehanna Railroad to Easton, Pa. This completed a direct all-rail route from Wilkes-Barre to the New York harbor (by way of the Central Railroad of New Jersey). Up to this time, all freight and passenger traffic passed over the planes, but in 1866 and 1867 there was constructed what was known as the "back track" down the mountain side between Solomon's Gap and Ashley over which all the passenger traffic and empty cars thereafter passed; it is now known as part of the main line. For the handling of the heavy coal traffic, however, this would have involved a continuous climb from Ashley, 170.27 mi., from New York, to Solomon's Gap, 157.8 mi. from New York, or a distance of 12.47 mi., and a total ascent of 1013.75 ft., composed of grades 95.61, 83, and 51.4 ft. per mi., respectively, and

Jan 1, 1922

By E. A. Gulbransen, J. W. Hickman

INTRODUCTION DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may occur to such a degree that oxides may form in the body of the film and on the outer surface which are different from those that would normally form if the additional elements were not present. The use of transmisson electron diffraction may aid us in interpreting these phenomena. Up to the present time all of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physical state of the alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the removal of carbon by oxygen in a decarburization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with

Jan 1, 1948

Jan 1, 1907

By CARL B. SNYDER

PERHAPS the most extraordinary thing about business, the trade and production of the country as a whole, is its amazing continuity and growth, its momentum and energy. It goes on year after year, growing steadily, almost without breaks, in spite of every kind of disturbance. We have been grossly deceived into the idea that business is highly variable. We have taken a few things like pig iron, and the like, constructional activity broadly, and imagined that these are a trustworthy measure of trade. Actually they are the worst that we could find. They do not apply to more than 10 per cent or, at the most, possibly 15 per cent of the total of the country's industrial activity. The other 85 or 90 per cent, or even more, goes on growing surely and steadily just like the growth of population and the steady advance in technique, invention, discovery, and improved methods of production Let me give you what seems to me one of the most remarkable examples of this amazing momentum and regularity. You know that 90 per cent or more of the business of the country is done 'by means of checks. About seven-eighths of the total of all checks drawn are reported regularly every week in the newspapers. Let us follow these reports from week to week, just as they come, and plot them up against the correspond- ing weeks of last year, and the year before, and the gear before that, as far back as you would like to go. Take especially the figures for 140 selected cities out- side of New York.

Jan 1, 1929

By Willard Ide Pierce

CONSIDERING the extent of the gold-fields of Nova Scotia, which occupy an area of 6000 to 7000 square miles, a few words as to the cost of extracting and reducing the ores may prove of interest. The veins are for the most part narrow, 4 to 12 inches being the usual width, while a 2-foot vein is considered a large one; but they offer many advantages, inasmuch as the ore is easily treated, wages are low, and machinery and supplies can be transported by water to within from 1 to 15 miles of the different mining districts. The Salmon River vein is a notable exception to the above rule as to width. It ranges from 4 to 20 feet in width. The Hall-Anderson of Fifteen-Mile Stream (where there are several veins) is another, which has proved to be from 3 to 4 feet in width. The ownership of all mining claims is retained by the Crown, but persons wishing to work them can lease as many unoccupied areas as they please for twenty-one years, with option of renewal, on the payment of two dollars for each area, and a royalty of 2 per cent. on all gold extracted. Each area consists of 150 Get along the lode and 250 feet across, upon which a certain amount of work must be done, which by recent law is reduced from one hundred to forty days' work for each area every year. Any person erecting in a district the first mill, having at least 8 stamps, and being at least 10 miles from any other mill, is entitled to a lease of 10 areas, free from advance-payment and from royalty, for twenty-one years. A record must be kept, and filed every quarter at the office of the Commissioner of Mines, of the total number of days' work done on the areas, and a monthly statement of the number of tons crushed, and the actual yield of gold. Gold-mining in Nova Scotia may be said to have commenced with the finding of a nugget of gold in a brook at Tangier in 1858. The following table, taken from the official report," gives the total yield

Jan 1, 1885

By James Norman, Benjamin S. Lindsey

Barite (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some binds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to I00 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaS04, II.II. per cent SiO2, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of non-metallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is separated. Laboratory Flotation Work Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coel for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1943

By Benjamin S. Lindsey, James Norman

Barite (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some binds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to I00 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaS04, II.II. per cent SiO2, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of non-metallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is separated. Laboratory Flotation Work Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coel for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1943

By Earl Oliver

SEVERAL notable papers, and free discussion on many controversial subjects, marked the various sessions of the Petroleum Division at the annual meeting. The Division first convened on Tuesday afternoon, Feb. 16, and wound up with a dinner and technical meeting on Thursday night. H. C. Fowler presided at the opening session, which was devoted to problems of engineering research and production engineering. Joseph Chalmers abstracted his paper on the flow of air and gas through porous media, in the preparation of which E. L Rawlins and D. B. Talia-ferro contributed. G. H. Fancher told how much he and his associates at Pennsylvania State College were interested in this field, and described the problems they had met in conducting test work. He made a plea for standardization of testing methods. Mr. Fowler then read an abstract of written discussion by Professor Barb, which was followed by discussion by Dr. Fancher and Mr. Chalmers of technical points in connection with the Chalmers' paper. H. H. Hill abstracted written discussion from Messrs. Wilde and Moore, of the Humble company. The second paper, by K. B. Nowels, on computing pressure drop in the pipe of flowing oil wells, was abstracted by the author. Messrs. Blair Smith, G. W. Coggeshall, and I. I. Gardescu participated in the discussion, and the chairman abstracted written discussion prepared by Mr. Rawlins. Most of this had to do with the viscosity of gas¬oil mixtures, on which subject Mr. Nowels said there was great need of accurate technical information.

Jan 1, 1932

Andrew Carnegie, America's best-known ironmaster and philanthropist, died at his home at Lenox, Mass., Monday, Aug. 11, after a three days' illness. A pioneer in the steel industry, he introduced into this .country the Bessemer process And formed the plans that have resulted in this country's supremacy in the steel markets of the world. Known throughout the world for his, gifts, he is also known to engineers as the donor of the home of their National Societies and as the founder of the Carnegie Institute of Technology, of Pittsburgh. For many years, also, he was an honorary member of the American Institute of Mining and Metallurgical Engineers, the American Society of Mechanical Engineers, and of the Engineers Club of New York. What he considered the secret, of his success is shown by the epitaph he wrote for himself, "Here lies a man who knew how to enlist in his service better men than himself." He was buried Thursday, Aug. 14, in Sleepy Hollow Cemetery, Tarry-town, N. Y., the funeral services being private, in accordance with his wish.

Jan 9, 1919

By Chester S. Conrad

SEVERAL years ago Pittsburgh Consolidation Coal Co. intensified efforts to combat the hazard of mine fires. The program consisted of three parts in the order of likely accomplishment: 1) Purchase and installation of newer and more practical fire fighting equipment. 2) Establishment of trained fire fighting teams at every mine plant. 3) A drive to remove the causes of mine fires. Experimentation with alternating current on section equipment is a major development in this part of the program. Use of alternating current to power mining equipment had been recognized as being most practical from the standpoint of safety. A means to re- place the d-c traction motor is all that has delayed complete section mechanization with a-c power.

Jan 1, 1958

By M. B. Willey

The Louisiana Continental Shelf is a submarine area extending offshore as much as one hundred miles. The Gulf bottom in this region varies considerably in extent, profile and composition and consists largely of sedimentary deposits, predominantly those of the Mississippi River. It is very young in a geological sense. Up to the present time few major structures have been erected offshore in the Gulf and no comprehensive preliminary tests have been carried out. Results of pile driving tests are of little value as actual bearing capacities far exceed the dynamic resistance to driving as measured by conventional formulas. Soils encountered are, with few exceptions, cohesive and piling consequently develop their supporting power through surface friction. Because of the time required and relatively high costs, no complete load tests have been made. The results of those tests which have been made, and information obtained from pulling piling in one structure, indicate that design loadings could be considerably increased, and it is contended that comprehensive preliminary investigations including an actual load test, combined with borings and examination of materials encountered by competent soil experts, would effect economies in design far in excess of their cost. The Louisiana Continental Shelf—General The Louisiana . . . continental shelf is a submarine area which extends seaward for as great a distance as one hundred miles off the present shoreline. The Gulf bottom in this region is characterized by low slopes and its outer margin is outlined by the fifty fathom (300 ft.) contour. South of the margin of the shelf the slopes steepen abruptly in the continental slope zone and plunge into the deeps of the Gulf of Mexico.l The engineer who is called upon to design a structure on this shelf is concerned only with the uppermost portion to a depth generally not to exceed Ioo to 150 ft. This layer is very young in a geological sense, and it has the characteristics usually associated with infancy. A few of these are lack of strength, lack of uniformity, and high water content. It consists of the sedimentary deposits of the various rivers and streams entering the Gulf. These streams are all heavily burdened in quantities sufficient to fill the areas at their mouths, were it not for the fact that continual subsidence, equal or greater in amount and acting directly opposite, prevail over the sedimentary workings of the streams. This subsidence has been estimated by geologists to be at the rate of at least one foot per century. Influence of Mississippi River The Mississippi River, which has been the predominant factor in the formation of practically all the Louisiana continental shelf, is one of two rivers flowing into the Gulf that have been able to build protruding deltas. The Mississippi has done so because of its enormous size and load. It deposits sediments in amounts sufficient to replace and actually gain on the amount of subsidence.

Jan 1, 1949

By Charles B. Henderson

DESPITE the loss, by enemy conquest, of a high percentage of our normal sources of supply for tin, the position of this important metal is easier today than that of rubber and a long list of other strategic materials, many of which are produced in this country. Actually, there is no shortage of tin for essential war purposes, owing to a strict control of its use, to increasing considerably the amount of secondary tin available, and to the foresight of the Government in authorizing the Reconstruction Finance Corp., as early as June, 1940, to acquire and produce certain critical and strategic materials of which tin was one of the most important. The construction of the Longhorn Smelter on the Gulf Coast in Texas is an important part of this program.

Jan 1, 1943

By M. J. Marcinkowski, Gordon E. Lakso

An extensive investigation has been made of the deformation behavior associated with the Fe3Si super-lattice using transmission electron microscopy techniques. Above 243°K the stress-strain curve exhibits three stages. Stage I occurs at a very low stress level and is related to the generation of perfect superlat-tice dislocations. Stage II is characterized by an extremely rapid rate of work hardening and is associated with the Taylor type locking of these superlattice dislocations. Finally Stage III is related to dynamic recovery processes since the work hardening rate is very small. Below 243ºK, only Stage I is observed, but it occurs at a much higher stress level. This latter observation is related to the generation of imperfect dislocations in Stage I with the consequent production of second nearest neighbor antiphase boundaries. The reason for this is that insufficient thermal energy is available at these low temperatures to generate the complete and perfect superlattice dislocations. It has been shown that the fully ordered FeCo alloys, i.e., those possessing the B2 type structure, exhibit three distinct stages of work hardening whereas the corresponding disordered alloys show only one.&apos;" This difference in behavior between the disordered and ordered alloys has been attributed to the fact that dislocations in the former case travel only as ordinary 1/2ao(111) types whereas in the latter case the move through the lattice as coupled 1/2a0(111) dislocations separated by an antiphase boundary (APB), i.e., the so-called superlattice dislocation. Although some preliminary work has been carried out concerning plastic deformation in ordered alloys possessing the DO3 type superlattice,3 no detailed analysis similar to that described in Refs. 1 and 2 has been attempted. Specifically, it has been suggested that the superlattice dislocation in this particular type structure should consist of four ordinary 1/2ao<111> types bound together by first and second nearest-neighbor APB&apos;s. Fe3A1 and Fe3Si are the two classic alloys possessing the DO3 type lattice; however, because of the somewhat higher ordering energies associated with the FesSi alloy, which in turn assures that dislocations will travel through the lattice as perfect superlattice dislocations under at least some conditions, it was chosen for the present investigation. Because of the extreme brittleness of Fe3Si, all deformation was done in compression. Stress-strain curves were obtained using both polycrystalline samples as well as single crystals. In the latter case the crystals were oriented so that deformation could be controlled either by single or double slip. They were then wafered parallel to and at various angles to the operative slip planes. These wafers were in turn examined by transmission electron microscopy (TEM) techniques in order to determine the extent of the interaction from the dislocation configuration contained therein. EXPERIMENTAL PROCEDURE The alloys used in this investigation were arc melted under helium from electrolytic iron of greater than 99.90 wt pct purity and transistor grade silicon of 99.99 wt pct purity. A typical analysis of interstitial impurities showed 120 ppm 0, 15 ppm N, and 65 ppm C Because of the extremely low ductility of the Fe3Si alloys, it was necessary to spark cut 0.230-in. diam polycrystalline cylinders 0.400 in. long from arc-melted fingers using a thin-walled brass tube as a cutting tool. The polycrystalline alloys could not be recrystallized since very little strain was induced in preparation. However they were annealed at 1273°C for 15 min in evacuated vycor capsules to relieve any cooling stresses that may have developed during solidification and then air cooled. The resulting grain size of the alloy was 0.50 mm. According to warlimont4 1273ºC is just within the single phase field where FesSi possesses the DO3 type lattice. In addition because of this high critical ordering tem-ature, air cooling from this temperature was believed sufficient to fully order all of the Fe3Si samples used in the present investigation. For the same reason, no attempt was made to achieve any degree of disorder by quenching. In fact, rapid quenching from 1123°K caused cracking. Such cracking was first suggested by sato5 with respect to the experimental observations of Glaser and Ivanick.6 Single crystal compression specimens were spark cut from single crystal ingots grown in a Bridgman type furnace. The iron and silicon for the crystals was prealloyed by arc-melting two 130-g buttons which were cut into small pieces before remelting in the furnace. This procedure resulted in a long-range inhomogeneity of 0.5 at. pct Si between the top and bottom of the 2-in.-long single crystal ingot, which was assumed to be negligible in the present investigation. The single crystals, after orienting and spark-cutting, were about 0.37 in. by 0.37 in. in cross section and about 0.5 in. long. True stress-strain curves were obtained using an Instron Tensile Testing machine in conjunction with techniques described previously. 1,7 The strain rate was 0.05 in. per in. per min. Prior to testing, the ends of all the compression cylinders were hand polished using a special jig to insure parallelism after which the sides of the samples were electrochemically polished to eliminate stress risers and to facilitate slip line observations. Test temperatures between 77" and 823°K were obtained using various cooling and heating media as described in Ref. 7 while at the upper end of this temperature range, a mixture of equal

Jan 1, 1970

By I. Havenaar

Various methods have been proposed in the literature to calculate the pressure losses in drill-pipe and bit-nozzles, i.e., those parts of the mud-circuit where the largest pressure-losses occur. Very few data, however, are available to check the validity of these proposals. Presented in this paper are the results of pumping experiments with clay-water drilling fluids of different specific gravities and different laminar flow-properties (differential viscosity and Bingham yield value), using pipes of different diameters. In addition, a series of measurements on bit-nozzles is discussed. Two main conclusions may be drawn from this work for the flow through pipes. 1. In the laminar flow region pressure losses can be calculated from the differential viscosity and Bingham yield value of the mud. 2. In the turbulent flow region pressure losses can be calculated with good approximation from a viscosity term which is determined by the volume fraction of the dispersed phase. Calculations making use of laminar flow properties may lead to erroneous results. The effect of temperature on the pressure losses in the case of turbulent flow can be calculated from the change in viscosity of the dispersing medium, i.e., water. The main conclusions determined for the flow through bit-nozzles are that for flow conditions prevailing in the field, the pressure-drops in bit-nozzles are independent of the laminar flow properties of the mud. They are solely determined by the density of the mud and the geometry of the nozzle. INTRODUCTION The last decades have witnessed a steady increase in the depth of oil wells. This is illustrated by the increase in the drilling depth record in the USA from 8,046 ft in 1927 to 21,482 ft in 1953. This increasing depth, together with the experience that high rates of mud circulation and high fluid velocities in the bit-nozzles enhance the rate of drilling, has emphasized the importance of selecting suitable mud-pumps when starting the drilling of a deep borehole. For such a selection it is necessary to be able to calculate the pumping pressures necessary to obtain the required circulation rates. The main part of the pressure-losses in the mud circuit occur in the drill pipe and the bit-nozzles. Various methods have been proposed in the literature to calculate the pressure-losses in the drill pipe1,2,3,4. These methods do not all lead to the same results, and at the time this investigation was started insufficient basic data were available to check their validity. Moreover, to our knowledge, no data are available at all on the effect, if any, of the flow-properties of the mud on the pressure-losses in bit-nozzles.

Jan 1, 1955

By Leroy Gardner

EVERY reader of this paper is well aware of the fact that the prolonged inhalation of large amounts of free silica dust results in fibrosis of the lungs, and that other inorganic dusts, except those of asbestos and the mineral poisons, are thought to be relatively harmless. But probably few have had opportunity to visualize the effects of silica, asbestos and other minerals upon living tissues. The ideal demonstration would be based upon sections of lungs from human beings that had inhaled com-parable concentrations of different dusts for a unit period of time. Such material is generally difficult to obtain and in some instances is of ques-tionable value because the subject has been exposed to more than one kind of dust. A demonstration could be prepared from the lungs of animals. However, so many months or even years are required to com-plete the exposure to each kind of dust that enough material has not been accumulated. For a general survey of the action of different types of dust, I am therefore compelled to use the tissues of animals that have been injected with suspensions of dust particles. The injection method offers certain advantages. The quantity, the particle size and the state of dispersion can be controlled with sufficient accuracy so that the tissue responses to different minerals can be accu-rately compared. The method insures contact between the tissues and the mineral particles; protective mechanisms, which may prevent the inhalation of certain types of foreign body, never come into play. If the pathway of injection be one that minimizes nonspecific injury, the tissue responses may simulate those produced by inhalation but they develop somewhat more rapidly. It should always be remembered that injection methods merely demonstrate the capacity of various kinds of minerals to provoke reaction in the tissues; whether the same substances are inhaled from atmospheric suspension and accumulate in the lungs in dangerous quantities can be demonstrated only by inhalation.

Jan 1, 1938

By Olaf Hondrum

CHURN drilling equipment at Bagdad consists of two Bucyrus Erie 27-T model drills and one 22-T drill with gasoline engines. The drilling tools weigh approximately 1600 lb. The holes are drilled with 7-in. bits which are heated in an oil burning furnace and sharpened in an electrically powered bit sharpener. A service truck brings the bits to the drills and takes the dull bits back to the shop. The bits weigh around 250 lb. when new and are handled by drill crews without any mechanical handling device. When the management decided to start open- pit operations in 1945 the ruggedness of the terrain was one factor that led to the purchase of the small 22-T model drill. The orebody lies on both sides of Copper Creek Canyon. The sides of the canyon are steep and are cut by numerous narrow branch gullies. The drill had to travel over roads that were narrow and steep. It proved adequate for drilling the capping formation and is still in use.

Jan 1, 1950