Search Documents

By George Simkovich

It was hypothesized that solid-state point defects should alter the flotation properties of solids. Tests conducted on pure AgCl and AgCl doped with CdC12 show that atomic point defects exhibit an important role in the floatability of AgC1. Tests conducted on PbS doped with Ag2s or Bi2S3, also show that the defect structures resulting from these dope additions, i.e., a combination of electronic and atomic point defects, contribute significantly to the flotation of PbS. IT has been established that flotation occurs only when a finite contact angle exists between a solid and a gaseous bubble.' This angle, measured through the liquid phase, is expressed by the equation where the are inter facial free energies and the subscripts S, G, and L represent solid, gas, and liquid phases, respectively. As is seen in Eq. [I] three interface free energies, sG, sl, and GL, enter into the contact angle equation. Therefore, any variation in these energies which sufficiently varies the contact angle will, in turn, vary flotation processes. Changes made in any of the phases concerned, i.e., gas, liquid, or solid phase, are reflected through the changes occurring in two of the surface energy terms. Thus, a change in the liquid composition would be noted in sL and GL, and it is this phase, the liquid, which is most frequently altered in flotation studies., Changes in the solid phase must be reflected through the changes occurring in the sG and sL terms. In particular, it is hypothesized that changes in the surface concentrations of point defects in the solid-phase will alter the sG and sL terms which, in turn, will be reflected by flotation results. As an illustration of this hypothesis one may consider the defect structure and the flotation of AgC1. The bulk defect structure of AgCl is essentially one involving equal number of cation vacancies and interstitial cations.3 Upon adding CdC1, to AgC1, a greater number of silver ion vacancies are created in the bulk of the crystal.4 On the surface of the crystal the smaller binding forces and the free space accomodations may also allow for the creation of "surface interstitial anions", which will be designated as ad-anions. Thus, the point defect structure of the surface of AgCl doped with CdCl, will consist of cation vacancies and/or adanions. If the molecular forces responsible for the surface energies, ?SG and ?sL, are significantly altered by the presence of these surface point defects, then differences in flotation results will be noted as the concentration of these defects is varied. The defects present in AgCl are predominantly atomic in nature. In the case of PbS both electronic and atomic defects are present.5 This compound conducts electrically by either electrons or electron holes depending upon whether excess lead or excess sulfur is present. Upon disolving BiS3 in stoichio-metric PbS, one increases the concentration of cation vacancies and the number of electron carriers in the bulk of the crystal.5" At the surface, the possibility of ad-anions must also be considered. Conversely, upon dissolving AgS in stoichiometric PbS one increases the concentration of interstitial cations and the number of electronhole carriers in the bulk of the crystal.5,6' At the surface the interstitial cations will be designated as ad-cations. Thus, the point defect structure of the surface of a PbS crystal doped with Bi2S3 will consist of a number of cation vacancies and/or ad-anions and an excess of electrons. Conversely the point defects on the surface of a PbS crystal doped with Ag2S will consist of a number of ad-cations and an excess of electron holes. Again, as in the case of AgC1, should the molecular forces responsible for the magnitude of the interface free energies, ?sG and ?sL, be significantly altered by the presence of these surface defects then significant differences in flotation results will be noted as the concentration of these defects is varied. EXPERIMENTAL To test this hypothesis flotation tests were conducted on pure and doped AgCl and on PbS doped with either Bi2S3 or Ag2S. Preparation of the AgCl samples was performed as follows: AgCl and weighed amounts of CdC1, were melted in a porcelain crucible. The melt was then forced through a capillary tube and the particles emitted solidified in air as they fell about 1.5 meters. Spherical particles, -0.50 + 0.25 mm, were separated from the remaining solidified material

Jan 1, 1963

By Philip D. Anderson, Ralph Hultgren

Heat contents of extremely pure iron were measured over the range 300"to 1433"K, using a diphenyl ether calorimeter. Results from three samples containing widely differing impurities agreed with one another and with Previously reported results at higher temperatures (1184 ° to 1809°K) by Olette and Ferrier. From these data a table of heat contents of iron has been Prepared which is believed to be more accurate than those previously available. CP values have been derived which are consistent with these heat contents, with the best experimental Cp data, and with the thermodynamic conditions of equilibrium between bcc and fcc iron. The opinion is expressed that low-temperature extrapolations of presently known Cp values for y-Fe are not reliable. It would seem that the thermodynamic properties of iron, which is by far our most important metal, should have been well established long ago. This is not the case, however. As discussed by Olette and Ferrier,' there is objection to every earlier heat content measurement. While the best true Cp determinations agree well at temperatures below the Curie point, there is wide divergence at higher temperatures. Several investigators have examined available data and attempted to calculate thermodynamic functions for iron that are consistent with the two equilibrium temperatures of bcc and fcc iron. The two primary efforts were those of Austin' in 1930 and Darken and smith3 in 1948. The recommended values differ considerably; integration of Austin's Cp values leads to a heat content at 1100°K which is 300 cal per g-atom higher than the value recommended by Darken and Smith. The compilation of Fisher4 in 1949 was based on the selection of Austin. In 1956, Weiss and Tauer obtained yet another set of values by resolving Cp values into components due to dilation, lattice vibration, electronic excitation, and magnetism. The magnitude of contribution by each component and its dependence on temperature was estimated by semiempirical means. Their values are not self-consistent in that they do not form smooth curves when plotted vs temperature; moreover, their calculations cannot easily be repeated since they do not give the values of some of the parameters used. Clearly, experimental values for iron were in a most unsatisfactory state. The presently described measurements of the heat content of iron were therefore undertaken, covering temperatures as high as 1433°K. While the work was in progress, the high-temperature (1193" to 1789"K) heat content measurements of Olette and Ferrier' were published; in the region of temperature overlap the present results agree with Olette and Ferrier well within experimental accuracy. It is believed that the present results, combined with those of Olette and Ferrier, provide for the first time a reliable set of heat contents of iron from room temperature to the melting point. From these data, guided by available Cp measurements, it proved possible to derive Cp, entropy, and free energy function values for @-iron from room temperature to the melting point, and for y- iron in the temperature region of its stability. Exhaustive study led to the conclusion that extrapolations of y-iron functions to room temperature were not reliable enough to be useful; hence these have been omitted from the tables. EXPERIMENTAL Materials. Three samples of extremely high purity iron from different sources, containing widely different impurities, were measured. The first of these, designated "Chipman", was kindly supplied by Dr. K. K. Kelley of the U. S. Bureau of Mines from a lot which was made many years ago by Dr. John Chipman of the Massachusetts Institute of Technology. The second, designated6'Teddington", was supplied by the National Physical Laboratory, Teddington, England, from a lot zone-refined by them. The third sample, designated "Irsid", was supplied by the Institute de Recherches de la

Jan 1, 1962

By R. S. Archer

THE binary aluminum-silicon alloys have certain characteristic advantages which are now well known, and these alloys have come into considerable use during the past several years.1 Their field of application has been limited to a certain extent, however, by their low yield point and hardness, low endurance limit, and relatively poor machining characteristics. These properties are improved by the addition of copper, and the ternary aluminum-silicon-copper alloys constitute an important class. The addition of copper decreases the corrosion resistance of the aluminum-silicon alloys and increases specific gravity. Magnesium is a hardening addition which seems to have relatively little effect on corrosion resistance, and which, of course, reduces specific gravity. The object of the work described in this paper was the development of alloys and heat treatments for the production of sand castings and permanent-mold castings having substantially all the advantages of the binary aluminum-silicon alloys together with mechanical properties improved to a degree permitting wider application.

Jan 1, 1930

By Andre Hubaux

In the writer's opinion, more stress should be put on field and microscope observations, as J. L. Gillson does. His discovery of relics of big labradorite feldspars from the Marcy anorthosite in all the other rocks is proof enough that previous field observations have been inadequate. The writer's field experience with anorthositic massifs is limited to the Egersund-Sogndal district in southern Norway; however, this is a very large and well exposed area. It seems to have so many points in common with the Adirondack region that a detailed comparison should be beneficial. This comparison was not possible 20 years ago, owing to the scarcity of geological data, at least for Norway. Both regions are now far better known-the Norway district because of the work of Professors Bugge and Barth33-35 and especially because of the extensive field and microscopic research of P. Michot,36-46 who introduced me in the field to the problems of that region.

Jan 3, 1958

By J. A. Herbst, D. W. Fuerstenau

This paper examines the zero order production phenomenon in the context of the size discretized batch grinding model. A restrictive interrelationship between the selection and breakage parameters of the model, which is mathematically sufficient to ensure zero order behavior, is delineated. Based on this interrelationship, a scheme is developed for predicting the values of the selection and breakage parameters for all size fractions from a minimum of experimental data. To test this scheme, dolomite was ground in a laboratory batch ball mill. Successful simulation of the comminution behavior of this system was achieved using the batch grinding model with the parameter values obtained from the proposed scheme. Historically, a preponderance of comminution research has centered on attempts to relate breakage energy to the performance of comminution machines. Concomitantly, grinding data were interpreted almost exclusively in terms of inherently empirical energy-size reduction relationships1-3 or "laws of comminution"4- 6 which were based on highly oversimplified descriptions of the fracture process. In some instances, these relationships provide a crude basis for the correlation of experimental data, but, invariably, this approach is inadequate for meaningful process simulation. The control and optimum design of comminution circuits require a mathematical model capable of depicting the size reduction behavior of every size fraction for grinding conditions of technological importance. Energy-size relationships do not provide this detailed information. For example, an energy-size analysis for batch ball-milled dolomite has recently been completed in the authors' laboratories.7 This analysis provided a satisfactory correlation between the hypothetical size modulus, which characterizes only the finer portion of the size distribution, and the input energy. However, this relation did not constitute an adequate description of the complete system. In general, one of two distinct viewpoints toward simulation has been adopted in recent comminution research. The first approach focuses on the fracture of single mineral specimens, with the essential aim of representing the over-all process in terms of the breakage characteristics of individual particles and the characteristics of the stress field which the particles experience within the particular size reduction device. As illustrated by Harris's review,' the actual incorporation of single-specimen fracture information into a description of the behavior of a multiparticle comminution system has seldom been attempted. The only model to accomplish this incorporation was the one developed by Schönert.8 The Schonert model treats single-passage grinding machines in terms of a distribution of effective loads acting on a particle, a distribution of required particle breakage energies, and the breakage product distribution. However, the use of single-particle fracture behavior to derive models of the size reduction process is at present limited to machines in which the particle residence time is approximately equal to the time required to apply stress. As a result, Schönert's analysis cannot be used to advantage to simulate the complex environment which prevails within a tumbling mill. For multiple-passage systems a second approach to the description of comminution processes has been more fruitful. This approach entails the formulation of a mathematical model which is phenomenological in nature in that it lumps together the entire spectrum of stress-application events which prevail in a system under a given set of operating conditions. The appropriately defined average of these individual events is then considered to characterize the over-all breakage properties of the device. Thus, to analyze the performance of a tumbling mill, the manner in which the particles of a particular size (or size fraction) are stressed need not be distinguished. Instead, a single parameter is assumed to represent the resistance of that size to fracture, given the average grinding environment which exists in the mill. The isolation of such a parameter and a related set of quantities, which constitute the breakage product size distribution for the average event in this size fraction, allows the formulation of physically meaningful descriptive equations capable of yielding precise and detailed information for simulation.

Jan 1, 1969

By Parke A. Hodges

CHROMIUM, one of the most vital of the strategic metals, has constantly increasing importance as research expands potential uses in alloy steel metallurgy. All signs point to a steadily growing use for chrome ore, and the general subject has received a great deal of attention recently.1 A relatively little known country, Southern Rhodesia produced a total of 5.949 million tons, or 18.6 pct of the total world chrome output, between 1906 and 1950, according to figures from the U. S. Dept. of Commerce. According to U. S. Bureau of Mines figures, Southern Rhodesia produced 291,525 tons in 1950 and 300,267 tons in 1951, or approximately 13 and 11 pct, respectively, of world production for the two years. In 1953 the Rhodesian Vanadium Corp. produced about 85,000 tons of which probably 7,000 tons were concentrate. Production by other companies was high. Large in themselves, the figures assume even greater significance because most of this output is of metallurgical grade.

Jan 8, 1954

By L. Adler

A fairly complex analysis is required to select or evaluate a piece of excavating and bulk handling equipment for its performance. At present, there is little agreement as to what points should be considered, and even less on what procedure to follow. This paper provides both of these in a consistent and direct form. The analysis applies to all types and sizes of equipment. The importance of the equipment characteristics, job activities, and work conditions are stressed. Separate analytical stems are established in a flow chart for these. They are combined using suitability tests in: problem statement; natural conditions; suitability guidelines; appropriate equipment types; operational activities; encumbered space; geometric design; equipment sizing; failure and limits; performance and consumption; public policy checks; and costs and profitability. Public policy and economics receive emphasis towards the end. The procedure is iterative, containing distinct feedback loops. Specifying the steps and sequence provides a necessary structure which has long been overdue.

Jan 1, 1985

By John B. Farish

This brief paper is designed to place on record some interesting occurrences, recently observed during an examination of the Golden Age Mine, in Boulder county, Colorado. Leaving the little village of Jamestown—or Jimtown, as it is more generally called—located in the canon of James creek, the road winds up a steep mountain composed of the coarse gray granite, with occasional belts of gneiss, common to all the mineral-bearing sections of Boulder county, to the summit of the front range of the Continental Divide. Here are located the mines known as the Golden Age and the Sentinel, the relative locations of which are shown in Fig. 1. The Golden Age location covers the outcrop of a quartz-porphyry dike, which cuts through the granite country-rock with a strike of about N. 70' E. This dike varies in width from a few feet, as at a point between the main shaft and the Hill shaft, to about 50 feet,

Jan 1, 1891

By John W. Gruner

On account of the tremendous increase in the production of steel there has been much speculation as to the reserves of iron ore. A number of estimates of world scope have been published, which show that these reserves are definitely limited if a long range view is taken. There are, however, optimists who believe that in perhaps two generations the metallurgy of iron will have advanced to the point where any kind of iron mineral combination of perhaps 20 pct iron will be usable. This thinking has been particularly applied to the new taconite developments of the Mesabi Range, for here is an iron formation of such vast extent that its iron could almost last forever. Let us briefly examine this most favorable of all low grade ore reserves in North America. Nothing will be said about the 1,000 million long tons of material now classified as ore, for they will be largely gone in less than 20 years.

Jan 3, 1954

By E. Maltby Shipp

WALLACE MCKEEHAN, Douglas, Ariz. (communication to the Secretary*).-In going over this report, which I have done very carefully, I find that the summary as composed deals with the various problems almost entirely from the employer's standpoint and that practically no consideration is given to the employee's point of view. An experience of 3 ½ years as safety inspector, and almost 30 years as workman-and official, has convinced me that any plan for the betterment of working conditions which will achieve any degree of success must give the workmen their share of responsibility and allow them full participation. The company may finance and direct the movement, but its ultimate success depends upon the support given by the workmen. The cooperation of the men doing the actual work is so essential that all writers insist that this must he secured, but they do not agree as to how this can best be done.

Jan 3, 1917

By AIME AIME

FOR the development of a mine, a shaft of small cross-section is usually sunk, of no larger size than is absolutely necessary. After the mine has been developed and put on a production basis it is a common practice to sink a shaft of larger cross-section for hoisting and use the original shaft for the handling of men and material into the mine. While that ar¬rangement is usually expedient, the small size of the supply cages presents a problem in the handling of ma¬terial. Where a cage is, say, 4 by 4 ft., which is not an uncommon size, all lengthy and bulky material must be handled piece by piece several times from the supply department to the underground stations. Thus drill steel and timbers over 4 ft. long will be loaded on cars at the supply department and wheeled to the shaft, where each piece must be unloaded from the cars and stood up in the cage. They are then lowered to the shaft station, unloaded piece by piece and placed in cars, run to the supply station and again unloaded and stored until called for. In such a case handling becomes a major item in the cost of supplies.

Jan 1, 1930

By Emmanuel P. Papadakis

Ultrasonic velocity measurements have been made to study the preferred orientation in cube-textured copper. Methods applicable to thin specimens were employed since the specimens were necessarily of sheet material. The measured velocities in various directions in the sheet differed from the corresponding values in single-crystal copper by 1 to 6 pet. The distribution of the deviations indicated that the align-ment of the (001) planes with the rolling plane was better than the alignment of the [100]and [010] directions with the rolling and transverse directions. Ultrasonic pole figures (velocity us orientation) are shown to be useful in the study of preferred orientation. THIS paper describes one set of experiments in a continuing study of preferred orientation in worked metals. This study has been undertaken to investigate the fundamental properties of metals when used as propagation media for ultrasonic waves. Many such materials are of current or potential use in ultrasonic delay lines. Fundamental studies on ultrasonic propagation parameters such as velocity, attenuation, and diffraction (beam spreading) are of importance in the design of delay lines, in the development of nondestructive testing methods, and in the study of materials themselves. Preferred orientation in worked poly-crystalline metals influences all three above-mentioned parameters, and hence is of particular importance. When polycrystalline metals are subjected to mechanical working, they develop textures dependent upon their crystal structure and the symmetry of the working operation.' The texture consists in the alignment of the crystallographic axes of the grains in preferred directions with respect to the symmetry axes of the working operation. Since the grains are elastically anisotropic, the elastic moduli of worked metals are anisotropic. Hence the velocities of elastic waves in worked metals depend on the directions of propagation and polarization. The worked metal may be thought of as taking on the elastic symmetry of a single crystal: so it possesses the same number of independent elastic moduli as the crystal class it simulates. In general, a worked metal does not adopt the crystalline symmetry of its own grains. For instance, most rolled sheet becomes effectively orthorhombic while all bar stock and wire develop hexagonal symmetry. However, certain metals with cubic crystal structure develop a cube texture upon rolling and annealing.= Nearly perfect alignment of [100]-type directions with the rolling direction, transverse direction, and rolling-plane norma1 can be achieved in certain fcc metals and alloys. These cube-textured rolled metals provide an excellent opportunity to test preferred orientation by means of elastic waves, since a worked metal with 100 pct cube texture would have elastic moduli identical to the moduli of its constituent metal. It is the purpose of this paper to present the results of an investigation upon cube-textured copper. Ultrasonic waves were used. The methods of measurement and the experimental results on the effective moduli will be given. The ultrasonic measurements will be shown to complement X-ray pole figures for the determination of preferred orientation in worked metals. EXPERIMENT To study cube - textured material, it was necessary to use thin-sheet material since a severe reduction in gage (95 to 99 pct) is necessary to produce cube texture. Special ultrasonic methods were needed to investigate the thin material at megacycle frequencies. A) Materials. The cube-textured material tested was a copper alloy containing 1 pct Zn. Specimens already measured for Young's modulus4 by Alers were kindly supplied by him. The specimens were slabs 3.00 by 0.25 in. cut from sheet 0.047 in. thick. The orientations of the long axes of the specimens with respect to the rolling direction were taken in 15-deg steps from 0 to 90 deg. B) Measurements. Two distinct experiments were performed to measure the phase velocity in these specimens. One measured the shear wave velocity for propagation in the 0.25-in. direction and polarization in the 3.00-in. direction. The other measured the velocity of both shear and longitudinal waves propagating in the thickness direction in the sheet. 1) Plate-Mode Measurements. The velocity of the zeroth-order shear mode5 was measured in the 0.25-in. direction in each strip. The specimens were ground thinner over half their length to assure that the first-order shear mode would be cut off below 6 Mc per sec, leaving the zeroth-order nondispersive shear mode as the only propagating mode. Piezoelectric ceramic transducers of 5 Mc per sec resonant frequency poled in their long direction were solder-bonded to the edges of the thin part of the slabs as in Fig. 1 after these edges had been made flat and parallel by fine grinding. These transducers produced waves polarized in the 3.00-in. direction and propa-

Jan 1, 1967

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin: The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most promising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestetn Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1947

By John J. Secretary Egan

The present list of problems relating to the physical chemistry of steelmaking has been prepared by the Committee on the Physical Chemistry of Steelmaking, from answers to a questionnaire submitted to a number of metallurgists engaged in both industrial and educational work throughout the United States. The purpose of the project is to make available to research laboratories a list of problems, all reduced to their simplest terms, the solution of which would aid in creating a better understanding of the steelmaking process. It is not intended to restrict the problems to practical steelmaking. The list also includes the study of the properties, and their correlation, as well as the physical and chemical reactions, of all substances that occur or that may be in any way associated with steelmaking operations, such as metallic substances, refractories, nonmetallic inclusions, and the constituents of slags. Many of the problems can be carried out in university or other research laboratories. Others may be most successfully attacked by cooperation of the research men with the operating personnel. It is the Committee's earnest wish that this cooperation be fostered. It is requested that investigators who are working on any of the problems listed and who anticipate future publication of their results, notify the Secretary of the Committee that such investigation is in progress. Suggested additions to the present list are also requested. The Committee is undertaking to act as a clearing house for information regarding the topics in this field that are being actually studied. Interested persons are invited to correspond with the Secretary. I. Data involved in the state of equilibrium for the various systems (laboratory work, almost entirely). A. Specific heats, heats of formation, entropies and free energies of various PURE ELEMENTS OR COMPOUNDS; ALSO CERTAIN TYPICAL SLAGS AND REFRACTORIES I. Determination of specific heats and entropies of oxides, sulphides, nitrides, etc, over a wide temperature range. 2. Determination of free energies of oxides, sulphides, nitrides, etc., over a wide temperature range. 3. Determination of the heats of formation of the oxides, sulphides, nitrides, etc. 4. Determination of the thermodynamic properties of the more important mineral-ogical constituents of the basic open-hearth slags such as calcium silicates, calcium phosphates, calcium ferrites, manganese silicates, FeO and Fe2O3. 5. Determination of the specific heats of open-hearth slags, including liquid silicates, if possible.

Jan 1, 1941

By John J. Secretary Egan

The present list of problems relating to the physical chemistry of steelmaking has been prepared by the Committee on the Physical Chemistry of Steelmaking, from answers to a questionnaire submitted to a number of metallurgists engaged in both industrial and educational work throughout the United States. The purpose of the project is to make available to research laboratories a list of problems, all reduced to their simplest terms, the solution of which would aid in creating a better understanding of the steelmaking process. It is not intended to restrict the problems to practical steelmaking. The list also includes the study of the properties, and their correlation, as well as the physical and chemical reactions, of all substances that occur or that may be in any way associated with steelmaking operations, such as metallic substances, refractories, nonmetallic inclusions, and the constituents of slags. Many of the problems can be carried out in university or other research laboratories. Others may be most successfully attacked by cooperation of the research men with the operating personnel. It is the Committee's earnest wish that this cooperation be fostered. It is requested that investigators who are working on any of the problems listed and who anticipate future publication of their results, notify the Secretary of the Committee that such investigation is in progress. Suggested additions to the present list are also requested. The Committee is undertaking to act as a clearing house for information regarding the topics in this field that are being actually studied. Interested persons are invited to correspond with the Secretary. I. Data involved in the state of equilibrium for the various systems (laboratory work, almost entirely). A. Specific heats, heats of formation, entropies and free energies of various PURE ELEMENTS OR COMPOUNDS; ALSO CERTAIN TYPICAL SLAGS AND REFRACTORIES I. Determination of specific heats and entropies of oxides, sulphides, nitrides, etc, over a wide temperature range. 2. Determination of free energies of oxides, sulphides, nitrides, etc., over a wide temperature range. 3. Determination of the heats of formation of the oxides, sulphides, nitrides, etc. 4. Determination of the thermodynamic properties of the more important mineral-ogical constituents of the basic open-hearth slags such as calcium silicates, calcium phosphates, calcium ferrites, manganese silicates, FeO and Fe2O3. 5. Determination of the specific heats of open-hearth slags, including liquid silicates, if possible.

Jan 1, 1941

By R. E. Ogilvie, N. L. Peterson

Diffi-lsion measurements were conducted at all compositims in the bcc solid solution of the U-Nb system employing incremental couples at composition intemals of 10 at. pct. Diffusion coefficients were determined by the Matano method from concentration gradients obtained with the electron-probe microanalyzer. The activation energy for inter-diffi-lsion as a function of compositim shows three distinct regions: 1) 80 to 100 pct U.6= 30 kcal per mole; 2) 20 to 80 pct U, $ - 70 kcal per mole; 3) Oto 20 pet U, Q = i40 kcal per mole. The frequency factor, fi0 and the activation energy $ were found to be roughly related by the following equation: log Do ^9.7 X IO-5Q -6,6. The Kirkendall marker movement indicates that DU is larger than DNb between 16 and 100 pct U and DNb is larger than DU from 0 to 4 pct U. FOR practical as well as fundamental reasons, the rates of diffusion in alloys are of considerable consequence. Most solid-state reactions are largely dependent upon the diffusion of atoms through the lattice structure and along grain boundaries. The high-temperature strength and reasonable nuclear properties of niobium have prompted its use as a reactor material in contact with uranium fuel. Hence, diffusion data for the U-Nb system are of considerable importance. In the previous diffusion study1 on the U-Nb system using pure element couples, reliable data were obtained only in the range of 0 to 10 at. pct Nb due to the large variance of the diffusion coefficient with composition. Also, a large Kirkendall effect and considerable porosity in the uranium-rich areas of the specimen were reported, which suggests that the true diffusion coefficients are somewhat larger. The purpose of the present study was to obtain reliable diffusion coefficients at all compositions using incremental diffusion couples with intervals of 10 at. pct. In view of the abnormal self-diffusion be- havior of y uranium2-4 and some other bcc transition elements,&apos;-&apos; it was felt that a comparison of the interdiffusion coefficients in the bcc U-Nb system with those of Reynolds et al.9 for the fcc gold-nickel system might shed some light on the diffusion mechanism involved. Both systems have similar phase diagrams, in that complete solid solubility exists above a miscibility gap. EXPERIMENTAL PROCEDURE The uranium used in this investigation was obtained through the courtesy of Argonne National Laboratory. An analysis of this material detected only Si-30, A1-7, C-6, N < 10 and 0-18 ppm. The niobium was electron-beam melted material obtained from Stauffer-Temescal. The gaseous impurities were less than 50 ppm, and the spec troc hemical analysis showed Ta-500 and W-200 ppm. U-Nb alloys were prepared at composition intervals of 10 at. pct by melting the appropriate amounts of the pure elements in an arc furnace. The buttons were inverted and remelted 6 times to assure complete mixing. The buttons were then wrapped in molybdenum foil, canned in Zircaloy-2 or stainless steel, and hot rolled 30 pct reduction in thickness at temperatures between 850" and 1100°C. Alloys with 10, 20, 30, 40, and 90 at. pct Nb rolled quite easily under these conditions, but the 50, 60, 70, and 80 pct alloys remained brittle. After melting and rolling (when possible), the alloys were annealed for 24 hr at a temperature within 100°C of their melting point in a dynamic vacuum of better than 4 x 10-8 mm Hg. These treatments produced alloys which were homogeneous on a 1 p scale within the detectability limits of the electron probe. During fabrication, the alloys picked up as much as 100 ppm Mo and 100 ppm Zr. Other elements checked for but not found were Co, Cr, Fe, Mn, Ni, and Ti. The grain size of the annealed samples ranged from 3 mm for the uranium-rich alloys to 0.3 mm for the niobium-rich alloys. This permitted measurements of the concentration gradients in the diffusion samples without crossing more than one or two grains, thereby eliminating any grain boundary effects. The specimens were bonded by theU&apos;picture frame" technique as reported by Kittel.10 Specimens of composition b)U + (100 - x)Nb were sandwiched between two specimens of composition (x + 10)U + (90 - x)Nb after they were ground flat and parallel

Jan 1, 1963

By J. S. Hromatko, L. J. Gurevich

In the course of the examination, at the BureLu of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undcrtaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are, satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed." Table 1.—Thirty-"five-mdh Testing Record of Fusible Plugs Causes of Rejection Inspection Period June-November, 1916.................. 311 32.8 47.2 3.8 11.5 15. 1 10.9 1 1.9 4.5 December, 1916-May, 1917............. 318 71.4 28.6 2.2 4.4 12.8 5.9 i ... 2.8 June-November, 1917.................. 228 73.0 27.01 ... 9.6, 5.2 9.6&apos; ... 0.8 December, 1917-May. 1918............. 214 72.028.0 0.9 0.4 11.6 7.0 ... 7.9 June-November, 1918...............250 70.7 29.3 ... 2.0 20.0 5.2 ....2.8 December, 1918-April. 1919............ 23378.121.9 7.2 1.2 1 4.7 3.0 ... 6.0 Total 35 months....................1544.69.7 30.3 2.3 4.8 11 0 6.9 0.3 4.1

Jan 1, 1921

By Charles L. Mantell, James E. Hoffmann

Mechanical inclusion, electrophoretic deposition, and adsorption were studied as mechanisms for code-position of aluminas present in copper-plating electrolytes as an insoluble disperse phase. Mechanical inclusion was not a significant factor. That codeposi-tzon of aluminas by an electrophoretic mechanism was unlikely was substantiated by measurements of the potential of the aluminas. The alumina content of the deposits was studied as a function of the pH of the bath. These tests in conjunction with sedimentation studies demonstrated the absence of an isoelectric point for the alutninas over the pH range examined. Thiourea in the electrolyte (a substance known to be adsorbed on a copper cathode during electrodeposition) affected the amount of alumina in the electrodeposit. However, no adsorption of thiourea on aluminas in aqueous dispersions was detected. If it were possible to produce a dispersion-hardened alloy of copper and alumina by electrodeposition, an alloy possessing both strength and high conductivity at elevated temperatures might be anticipated. Investigation of the mechanism of codeposition of aluminas with copper was undertaken with the hope that knowledge of the mechanism would aid in the development of such an alloy. The word "codeposit" here does not necessarily imply an electrolytic phenomenon but rather that the materials codepositing, the various aluminas, are transported to and embedded in the electrodeposited copper by some means. Mechanical inclusion in electrodeposition implies a mechanism of codeposition which is wholly mechanical in nature; the only forces acting on a particle are gravity and contact forces. Such a particle is presumed to be electrically inert and incapable of any electrical interaction with electrodes in an electrolytic plating bath. Processes for matrices containing a codeposited phase by electrodeposition from a bath containing a disperse insoluble phase frequently state that code-position is caused by mechanical inclusion.10,2,12 If settling, i.e., gravity, be the controlling mechanism for codeposition of aluminas, then assumptions may be made that 1) the content of alumina in the electrodeposit should be enhanced by increasing the particle size, 2) the geometry of the system, that is, the disposition of the cathode surfaces relative to the di- rection of the falling particles, should affect the alumina content of the electrodeposit, 3) in geometrically identical systems the chemical composition of the electrolyte employed should exercise no effect on the alumina content of the deposit, that is, the alumina content should be the same in all cathode deposits irrespective of bath composition. A bent cathode19 evaluates the clarity of filter effluent in electroplating baths by comparing the roughness of the deposit on the vertical surface with that on the horizontal surface. Two difficulties are inherent in this technique: 1) the current density on the horizontal portion of the cathode would be substantially greater than that on the vertical surface; 2) should the deposit obtained be rough, projections on the vertical face could act as horizontal planes and vitiate the relationship between the vertical and horizontal surfaces. Bath composition should have no substantial effect on the alumina content of the deposit. Two different electrolytic baths were employed. They possessed variant specific conductances and substantially different pH ranges. The experimental tanks were rectangular Pyrex battery jars 6 in. wide by 3 1/4 in. long by 9 3/4 in. deep. The cathodes were stainless steel 316 sheet of 0.030 in. thickness, cut to 7.5 by 1.75 in. and bent at right angles to form an L-shaped cathode whose horizontal surfaces measured 1.75 by 3.0 in. All edges and vertical surfaces were masked with Scotch Elec-troplaters Tape No. 470. The anodes were electrolytic cathode copper 9 in. high by 2.25 in. wide by 0.5 in. thick. To eliminate inordinately high current densities on the projecting edge of the cathode, the anode was masked 1 in. above and below the projected line of intersection of the cathode with the anode. The exposed area of the anode was equal to that of the cathode, providing both with equal average current densities. The agitator in the cell was of Pyrex glass and positioned so its center line was equidistant from cathode and anode, and a plane passed horizontally through the center of the blade would be located equidistant from the bottom of the cathode and the bottom of the deposition tank. The assembled apparatus is depicted in Fig. 1. Hatched areas on anode and cathode represent the area of the electrodes wrapped with electroplaters tape. MATERIALS The chemicals were copper sulfate—CuSO4 • 5H2O— technical powder (Fisher Scientific Co.). Spectro-graphic analysis showed substantial freedom from antimony, arsenic, and iron. Traces of nickel were present.

Jan 1, 1967

By T. M. Olson, B. G. Lewis

The adsorption of selenite on bentonite, kaolinite, and an iron--coated illite was studied to determine the importance of several soil variables on selenite removal from uranium mill tailings pond seepage. Adsorption capacities of the clays of selenite varied by orders of magnitude and decreased in the following order: illite > kaolinite > bentonite. Maximum adsorption of selenite on the clays was observed between pH 2.5 and the clay&apos;s zero-point-of-charge. Substantially less selenite was adsorbed on these clays in actual mill tailings solutions than in model systems. Virtually all selenite was removed from the tailings at pH 7. The principal removal mechanism at this pH is suggested to be the adsorption of selenite on freshly precipitated metal hydroxides. It is concluded that selenite can be removed from tailings seepage in soil or in clay liners in the presence of kaolinitic clays and iron oxides. Selenite would also tend to be removed from tailings seepage in calcareous strata.

Jan 1, 1984

By H. C. Gatos, J. T. A. Pollock

It is well known that the superconducting critical current densities of many alloy superconductors may be increased by cold working and in some cases further enhanced by a short heat treatment. This latter enhancement has been attributed to the redistribution of dislocations into cell-like networks&apos; and to the precipitation of second phase particles,2&apos;3 which act as flux pinning centers. In a manner analogous to dislocation pinning in precipitation hardening alloys,4 it is expected that here also a critical distribution of the pinning centers should result in maximum pinning effect. Concentration inhomogeneities exist in most or all commercial alloys yet there have been only a few attempts made to determine their effect on critical current capacity in the absence of cold working. Sutton and Baker,5 and Kramer and Rhodes6 have found that the complex precipitation processes occurring during the aging of Ti-Nb alloys can result in critical current density enhancement. Livingston7-10 has clearly shown, for lead and indium based alloys, that the distribution of precipitated second phase particles is of critical importance in determining magnetization characteristics. However, these &apos;(soft" alloys age at room temperature and the time involved in specimen preparation prevents metallographic examination in the state in which the superconducting measurements are made. Thus results with such alloys are expected to be biased towards larger precipitates and interpar-ticle spacing. The present study of Ta-Zr alloys was undertaken to examine the influence of second phase precipitation, as controlled by heat treatment, on the critical current capacity of well annealed polycrystalline material. A study of the published phase diagram11 indicated that annealing supersaturated samples containing up to 9 at. pct Zr at suitable temperatures would result in the precipitation of a zirconium-rich second phase. It was MATERIALS AND PROCEDURE The alloys were prepared from spectrochemically pure tantalum and zirconium. Analysis was carried out by the supplier. Major impurities in the tantalum were: 12 pprn of 02, 17 pprn of N2, 19 pprn of C, and less than 10 ppm each of Mo, Nb, Al, Cr, Ni, Si, Ti. The crystal bar zirconium was pure except for the following concentrations: 15 pprn of 02, 17 ppm of C, 23 ppm of Fe, 11 ppm of Cu, and less than 10 pprn each of Al, Ca, N2, Ti, and Sn. Samples were prepared in the form of 8 to 10 g but-tons by arc melting using a nonconsumable electrode on a water-cooled copper hearth in a high purity ar-gon atmosphere. Each button was inverted and re-melted three times to ensure an even distribution of the component elements. The samples were then homogenized at temperatures close to their melting points for 3 days in a vacuum furnace maintained at 5 x 10-7 mm Hg. After this treatment the buttons were cold rolled to sheets approximately 0.020 in. thick from which specimens were cut, 0.040 in, wide and 1 in. long suitable for critical current density (J,) and critical temperature (T,) measurements. These strips were then recrystallized and further grain growth was allowed by an additional vacuum heat treatment at 1800°C for 60 hr. Some second phase precipitation occurred during cooling of the furnace and a solution treatment was necessary to produce single phase supersaturated samples. This treatment was successfully carried out by sealing the samples together with some zirconium chips in quartz tubes under a vacuum of 5 x 10-7 mm Hg, heating at 1000°C for 5 hr and then quenching into water or liquid nitrogen. The samples were then heat treated at either 350" or 550°C and quenched into water or liquid nitrogen. All samples which were heat treated at 350°C were quenched in both cases by cracking the capsules in liquid nitrogen. The samples treated at 550°C were quenched by dropping the capsules into water. Analysis for oxygen in randomly selected samples indicated that the oxygen content was in the range of 175 to 225 ppm. Values of Tc were determined by employing a self-inductance technique. Jc measurements were made at 4.2oK by increasing the direct current through the wire in a perpendicularly applied field until a voltage of 1 pv was detected with a null meter. The risk of resistive heating at the soldered joints during these latter measurements was reduced by first plating the ends of the wires with indium and then soldering to the copper current leads using tin. Metallographic examinations were performed after mechanical polishing of the same samples and etching in a 4H20:3HN03 (conc):lHF(conc) solution.

Jan 1, 1970