Search Documents

By W. I. Garms, J. L. Stevens

BECAUSE of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following resume of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. MILLS USED Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was I3 1/2 in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 16 2/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. INITIAL TEST During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1946

By Reinhard Fischer

The consumption of lead for batteries in some western countries and Japan amounts to 870,000 T. annually. Battery life is 2-3 years. Therefore after a short time a considerable quantity of lead flows back to smelters. The production of lead from scrap batteries is discussed from the following points of view: 1. Separation of the acid contained in the batteries. 2. Separation of the components which are free of lead from the components containing lead, e.g. cases, separators. 3. Separation of metallic lead from lead compounds. 4. Avoidance of manual-work. A process has been developed and perfected at a plant, which began operation in 1965. The procedure consists essentially of the following steps: 1. Breaking the cases and removing the acid. 2. Crushing the batteries in an impact mill. 3. Screening off separators. 4. Separation of slurry. 5. Gravity separation of metal and organic material. The plant has a one-shift capacity of -24,000 T. batteries/year.

Jan 1, 1970

Societies, Boards, Etc , on Which Institute Has Representation United Engineering Society WILLIAM L SAUNDERS, President GEORGE H PEGRAM, 1st Vice-president ALFRED D FLINN, Secretary J V W REYNDERS, 2d Vice-president JACOB S LANGTHORN, Treasurer HENRY A LARDNER, Assistant Treasurer Finance Committee GEORGE H PEGRAM Chairman J VIPOND DAVIES BANCROFT GHERARDI W F M GOSS WILLIAM L SAUNDERS, ex-officio House Committee ALFRED D FLINN, Chairman FREDERICK F SHARPLESS' GEORGE T SEABURYO F L HUTCHINSON CALVIN W RICE

Jan 1, 1923

By H. C. Rogers

A phenomenological study of the failure of polycry stalline ductile metals at room temperature was carried out using light and electron microscopy. Tensile fractures as well as sections of partially fractured bars of OFHC copper in particular were examined. The initiation and growth of the central crack in the neck of a tensile specimen occurs by void formation. After the formation of the central crack the f'racture may be completed in either of two ways: by further void formation or by an "allernating slip" mechanism. The first leads to a "cup-cone" failure; the second, to a "double-cup" failure. In the past decade or decade and a half there has been a great deal of emphasis on the solution of the problem of the brittle fracture of metals, particularly those which normally exhibit considerable ductility such as steel. Since the problem of the fracture of metals after large plastic strains has less immediate commercial or defense significance, there has been considerably less effort expended in describing the details of the phenomenology and determining the mechanism of this type of fracture. The present research was undertaken to increase our knowledge in this area. The problem of ductile fracture has not been neglected completely, however. Ludwik1 first found by sectioning a necked but unbroken tensile specimen of aluminum that fracture began with a large internal crack which appeared to have started in the center of the neck. Examination of the fracture indicated that the crack had propagated radially with increasing deformation until a point was reached at which the path of the fracture suddenly left this transverse plane and proceeded at approximately 45 deg to the stress axis until the surface was reached. This gives rise to the commonly observed cup-cone tensile fracture. When MacGregor2 was attempting to demonstrate the linearity of the true stress-true strain curve from necking until fracture, he found that copper was anomalous in that the stress dropped off markedly from the straight line value before fracture occurred. Radiography indicated that in the copper an internal crack was formed long before the final fracture, the stress decreasing during the growth of this crack. One of the most significant advances in the understanding of ductile fracture was the result of work by Parker, Flanigan, and Davis.3 By the use of etch-pit orientations they were able to demonstrate conclusively that the fracture surface at the bottom of the cup, although on a gross scale normal to the tensile axis, did not consist of cleavage facets as had been previously supposed by many investigators. Recently, Forscher4 has shown evidence of porosity near the tensile fracture of hydrogenated zirconium which he attributes to hydride decomposition. The workers at the Titanium Metallurgical Laboratory5 have also shown evidence of porosity in a number of the commonly used metals after heavy deformation. Many metals have relatively low ductility during creep tests at high temperature. The fractures are intercrystalline, resulting from the nucleation and growth of grain boundary voids. The work in this area has been recently reviewed by Davies and Dennison.6 It is possible that some of the observations and conclusions may have a bearing on the present study? especially since at least two studies7,' have been extended down to room temperature and below using magnesium alloys. However, since magnesium does exhibit low-temperature cleavage, these results may not be pertinent to the present one. The use of the electron microscope as an aid to the study of fractures has been extensively exploited by Crussard and coworkers.9 The examination of direct carbon replicas of the fractures of a large number of metals and alloys showed that the bulk of the fracture surface was covered with cup-like indentations of the order of 1 to 2 µ in size. These frequently had a directionality by which Crussard claims to be able to tell the direction of the crack propagation. With this rather disconnected background of information, this investigation was undertaken in the hope of presenting a unified picture of the initiation and propagation of a fracture in a ductile metal. To this end all of the techniques previously used were employed simultaneously so that there might be a good correlation of the data obtained by different techniques. EXPERIMENTAL PROCEDURE The metal which was chosen as the starting material for this investigation was OFHC copper. Of the dozen or so materials considered, it best fulfilled the requirements of commercial availability in large sizes, good ductility, relatively high melting point compared with room temperature and

Jan 1, 1961

By J. F. Smith, J. E. Davison

The heat capacity of CaMg2 was measured over the temperature interval, 4.8° to 287°K, by the technique of low-temperature adiabatic calorimetry. Heat content measurements were performed with a drop calorimeter over the temperature interval, 273" to 673°K. From these data the thermodynamic functions, (FT - H0)/T, ST - So, and & - Ho, were evaluated. A third-Law calculation of the standard entropy of formation of CaMg2 yields a value of -0.25 * 0.06 cal per (°K g-atom) , and the free-energy function derived from this study when combined with existing equilibria data yields a value for the standard enthalpy of formation which is in agreement with direct calorimetric enthalpy measurements. The accompanying paper' shows that the enthalpy of formation of CaMg2 has been determined with good precision by three different calorimetric techniques.'-= TWO independent determinations of the Gibbs free energy of formation of CaMg2 have also been made; both determinations were based on vapor pressure measurements, being in one case hydrogen vapor pressures over ternary Ca-Mg-H alloys4 and in the other case magnesium vapor pressures over binary Ca-Mg alloys.5 The present determination of heat capacity of CaMg2 below room temperature and of the heat content of CaMg2 above room temperature was undertaken to provide supplementary data. These data are useful in their own right but can in addition be used to evaluate an entropy of formation for CaMg2 which, because of the interrelation of free energy, enthalpy, and entropy, can be used as a check of the self-consistency of the composite of the presently available information. LOW-TEMPERATURE HEAT CAPACITY The heat capacity of CaMg2 was measured over the temperature interval 4.87° to 286.64°K in an adiabatic calorimeter. The physical details of the calorimeter and the experimental procedure for measuring the heat capacity of a specimen have been adequately described by Gerstein et a1.6 The source and purity of the calcium and magnesium are described together with the methods of sample preparation and chemical analyses in the accompanying paper.' Results of chemical analyses of the material which was used in the present investigation are shown in Table I. These analyses show that, on the basis of the published phase diagram,7 the heat capacity sample contained a slight excess of a calcium while the heat content sample contained a slight excess of magnesium. However, in both cases the excess was small, and X-ray diffraction patterns showed reflections which were without exception attributable to CaMg2. The sample which was used for heat capacity measurements weighed 69 g while the sample container and addenda weighed 132 g. The sample was in the form of annealed powder, 50 to 60 mesh, and was sealed into the sample container under 0.1 atm of helium. Copper fins inside the sample container facilitated thermal equilibrium of the powdered Sample. Time intervals of the order of 10 min were required for thermal equilibration, and such times are normal for this calorimeter regardless of the form of the sample. The observed heat capacities were corrected for the small excess of a calcium through use of the heat capacity values tabulated by Hultgren et a1.8 The corrected heat capacities are tabulated as a function of temperature in Table II. The free-energy function and the absolute entropy of CaMg2, which were calculated from the experimental heat capacity data, are listed in Table 111. A smooth curve was fitted to a plot of the experimental values of the heat capacity and in only two instances above 30°K did the plotted points deviate from the curve by more than 0.2 pct. Below 10°K the deviation of several of the points was as much as 50 pct. These large percentage deviations were attributed to the small value of the heat capacity and to the low sensitivity of the platinum resistance thermometer in this temperature range. The deviations in the region of 10°to 30°K were less than 5 pct. Although the percentage deviations of some of the low-temperature measurements are large, the actual value of these deviations is small since the magnitude of the heat capacity in that temperature range is small. The error in the value of the third-law entropy at 298.15°K was estimated to be less than 0.01 cal per (°K g-atom). A value of -0.25 ±0.06 cal per (°K g-atom) was obtained for the standard entropy of formation at 298.15°K from the relation:

Jan 1, 1969

By Cyril Wells

THE diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migra-tion of carbon in gamma iron occurs.1,2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with com-position, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schönert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By Colin Baker, G. C. Smith

Investigation of the initiation and propagation of ductile failure in OFHC copper was undertaken to determine the role of nonmetallic inclusions. The effect of inclusion initiated voids on the formation of the internal cavity and the final shear separation was studied by metallographic eranzination of strained test pieces. A strain anneal technique was used to enlarge the voids under uniaxial stress conditions to elinzinate triaxial stress effects. Measurements of void size us stress and strain were made to show the point at which void im'tiation begins and becomes an important factor in the deformation process. The work of separation of copper-cuprous oxide was determined to attempt to correlate the breakdown of the matrix inclusion interface with void initiation and propagation. The zloid shape and position relative to the tensile axis suggested an interface breakdown mechanisnz of initiation. Evidence is presented that shows a basic similarity between the central cavity propagation and the 45-deg shear portions of the failure. DUCTILE fracture has been studied by a number of workers1-lo and attention drawn to the importance of hard second phase particles in the initiation of the failure. Holes formed at the matrix-particle interface can elongate by plastic deformation and then subsequently expand sideways to link up and produce a major crack. This is usually observed first in the center of the macroscopically necked region of a test-piece where the hydrostatic stresses are at a maximum. As the crack spreads sideways towards the free surface of the specimen, well defined shear zones develop from the crack tip and the final separation is along a direction at approximately 45 deg to the stress axis. This shear failure may also be associated with voids formed adjacent to second phase particles. In this way a cup and cone type fracture is produced. The stage at which separation takes place between particles and the surrounding matrix has not been clearly identified. In addition, although researchers have dealt with anisotropy of tensile behavior" as a result of material fabrication variables, not much is known about the microstructural features of aniso-tropic behavior. In the present work evidence on these points is presented in relation to the behavior of copper containing second phase particles of cuprous oxide. I. MATERIALS AND PROCEDURES EMPLOYED The material used was +-in. diam or 2-in. sq cold-drawn OFHC copper bar which contained 0.6 pct by volume of cuprous oxide inclusions. These ranged in COLIN BAKER, Junior Member AIME, formerly at -mnF of Metallurgy, University of Cambridge, Cambridge, England, is presently Research Scientist Reynolds Metals Co., Richrnand, Va. G. C. SMITH, Member AIME, is Senior Lecturer, Department of Metallurgy, University of Cambridge. Manuscript submitted June 20, 1967. IMD size from approximately 1 to 6 p in length and 1 to 4 p in width. The shape was generally slightly ovoid. Tensile tests were made on specimens having a gage length of 2.5 cm and diameter of 0.643 cm. Metallographic examination was carried out by sectioning deformed and fractured specimens; in addition fracture surfaces were examined optically and with a scanning electron microscope. Some measurements of the work of separation between copper and cuprous oxide were made, using a sessile drop technique which was a modification of that used by Kingery and umenick." The best metallographic results were obtained by using a vibratory polisher, which minimized smearing of the surface. 11. RESULTS A) Initial Experiments. Specimens from the +-in. diam rod were annealed for 2 hr at 650°C in uacuo, at which temperature complete recrystallization occurred without any change in the form of the inclusion. They were then fractured at temperatures from -190" to 600°C. Cup and cone fractures were obtained at all temperatures from -196" to 400°C. With increase in temperature there was, however, a continuous increase in the extent of the central transverse area and a corresponding decrease in the shear portion of the fracture. Above 400°C, the fractures became intergranular. Sections of specimens tested below 400°C revealed extensive small voids which were always associated with inclusions. However, the voids only reached dimensions greater than the inclusion size in the region of the macroscopic neck, where they were many times longer. Lateral expansion was found only near the fracture surface of the test pieces. As observed by Puttick, the voids were either (a) triangular holes initiated in the direction of the tensile axis and elon-

Jan 1, 1969

Iowa Geological Survey, Des Momes, Ia. George F. Kay, State Geologist A list of publications will be sent upon request Most of the papers of the Survey have been published in the Annual Reports, issued since 1892. Separates of the many papers in the Reports may be had for postage, except where they are out of print, and except for vol 1 (1892), 2 (1894) and 14 (1903), where no separates are to be had. Thirty-five Annual Reports have been issued up to and including vol 35 (1929). A charge, plus postage, is made for vols, 4, 5, 7, 8, 9, 10, 28 and 33, others will be sent free upon request, plus postage on from 2 to 6 pounds Space prohibits giving more than a general picture of some of the contents; vols 4, 5, 7, 8, 9, 10, 11, 12, 13, 15, 16, 20, 27, 32, contain, among others, papers on the geology of Iowa, by counties Vol. 19 (1908), 6 lb , contains a number of papers dealing with the peats and coals of Iowa, and has bibliographies of those subjects Vol 22 (1912), 6 lb , contains an annotated bibliography of Iowa geology Vol-24 (1913), 6 lb , contains the analyses of 16 Iowa coals Vol 28 (1917, 1918), price $1 50, 4 lb , completely covers the subject of gypsum in Iowa, and has a bibliography of the sub¬ject. Each volume carries an administrative report and a review of mineral production for the period covered In addition, Technical Paper 2 (1930), Studies of Iowa coals, will be sent free upon request Also a geological map of Iowa, and maps of Iowa showing the distribution of the glacial drift sheets throughout the state, have been issued and are available

Jan 1, 1933

By M. J. Bradley, P. H. Dike

THE art of melting nonferrous metals, in smelting, casting, and in compounding of alloys, is highly dependent on a knowledge of the temperature of the metal. This knowledge may reside in the experience and judgment of the melter, or it may be based on measurement by suitable instruments. It-is our purpose to discuss briefly the instruments available for such measurements, and more at length the present, practice in molten metals, without recommendation. In the limits of time and space allotted, we can do little more than mention the available methods of measurement that are directly applicable in this field. In the 1939 edition of the Metals Handbook, issued by the American Society for Metals, pages 285-310, there is a more extensive discussion of pyrometry than can be attempted here, which should be referred to for details we must omit. For reasons that will appear, thermoelectric pyrometry will constitute the major portion of our discussion of the subject, only limited attention being given to radiation or optical pyrometry. METHODS OF MEASUREMENT THERMOELECTRIC PYROMETRY A thermocouple consists of two dissimilar wires, or a wire inside a tube of a dissimilar material, joined together at one end, which is placed in the region or medium where the temperature is to be measured, while the other ends are connected through suitable lead wires to a voltage-measuring device, which may be a millivoltmeter or a potentiometer. An electromotive force is generated in the circuit, which is proportional to the difference in temperature between the hot junction and the junctions of the lead wires to the measuring instrument. If this latter temperature is maintained constant, the e.m.f. measured varies only with the temperature of the hot junction. Every thermoelectric pyrometer is calibrated for a particular cold-junction temperature such as 0°F., 32°F. or 75°F., but usually it is more practical to compensate instrumentally over the probable range of cold-junction temperatures than to maintain the junction at the particular temperature for which the instrument was calibrated. Thermocouple Materials Only a very few pairs of metals are in frequent use for pyrometric measurements. The most generally used are iron-constantan for temperatures up to 1500°F. in oxidizing and up to 1800°F. in reducing atmospheres and chromel-alumel, which may be used in oxidizing atmospheres at temperatures up to 2400°F. for intermittent service. The accuracy of the latter deteriorates rapidly at temperatures above 2200°F. Platinum vs. platinum-rhodium thermocouples may be used up to a temperature of 3000°F , but they are easily contaminated by slow absorption of

Jan 1, 1946

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of com- plaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and ensure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage or breakage en route. The small sizes present in a car of prepared coal as received by the purchaser consist-of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' lass because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal.

Jan 1, 1943

By Zay Jeffries

A MORE complete interpretation of the amorphous theory in metals is given than has heretofore been offered. It is believed that Le Chatelier, Tammann, and Heyn, at present the ablest opponents of the amorphous theory, will not he able longer to continue their beliefs that surface tension alone can account for all the observed variations in the properties of single constituent metals. It is strongly advocated that the properties of any solid substance be studied from the standpoint of the number of constituents present, the quantity and arrangement of each constituent, and the properties, of each constituent. Each deformable crystalline constituent by plastic deformation will produce amorphous material, thus changing the properties. Considerable attention is given to the variations in properties of the amorphous and crystalline phases of any substance. These are summarized as follows: 1. The cohesion of the amorphous phase of a substance is substantially zero at the melting point while the cohesion of the crystalline phase is considerable at the melting point. With decrease in temperature, the cohesion of the amorphous phase increases at a faster rate than that of the crystalline phase; this differential rate of change of cohesion holds between absolute zero and the melting point. At a certain temperature

Jan 2, 1919

By John Birkinbine

Secretary's Note.—In printing this paper in the present volume, the figures given in the pamphlet edition have been brought more nearly up to date, the product of 1899 being in many instances inserted. Iron-Ore Resources. In a paper presented to the Institute in 1897,* I discussed the iron-resources of the United States as then developed, calling attention to some principal sources upon which other countries depended. The following statement will give a general idea of the amounts, as compiled from the latest official records, of ores won, and metal produced, in the nations which are important contributors to the world's output. Unfortunately these are not all contemporaneous, since in some countries the statistics do not appear until after one or more years. The statement covers not only pig-iron and iron-ore, but also manganese-ore —the manganese mined being principally used in the production of spiegeleisen or ferro-manganese, and these alloys being generally included in the pig-iron output. Table I, which epitomizes the present situation, shows respectively the countries and the quantities of iron-ore and man-

Jan 1, 1901

By S. N. Singh, M. C. Flemings

Results are presented of a study on the combined influences of ingot dendrite am spacing and thermo-mechanical treatments on the fracture behavior and mechanical properties of high purity 7075 aluminum alloy. The most important single variable influencing mechanical properties was found to be undissolved alloy second Phase (microsegregation inherited from the original ingot). Ultimate and yield strengths were found to increase linearly with decreasing amount of alloy second phase while ductility increased markedly. At low amounts of second phase, transverse properties were approximately equal to longitudinal properties. In tensile testing, microcracks and holes were invariably found to originate in or around second phase particles. Fracture occurred both by propagation of cracks and coalescence of holes, depending on the distribution and amount of second phase. IN most commercial wrought alloys, second phase particles are present that are inherited from the original cast ingot. These include, for example, non-equilibrium alloy second phases such as CuAl2 and impurity second phases such as FeA13 and Cr2A1, in aluminum alloys. A previous paper1 has dealt with the morphology of these second phases in cast and wrought aluminum 7075 alloy, and with their behavior during various thermomechanical treatments. In this paper we discuss the influence of the particles on mechanical properties and fracture behavior of the alloy. Previous experimental work indicating a direct and major effect of second phase particles on mechanical properties (especially on ductility) includes the work of Edelson and Baldwin on pure copper.' Also relevant are the many studies demonstrating the important effect of nonmetallic inclusions on the fracture of. steel.3'4 Work on aluminum includes that of Antes, Lipson, and Rosenthal5 who showed that a dramatic improvement in ductility of wrought aluminum alloys of the 7000 series is achieved by eliminating second phases. It now seems well established that included second phases play a dominant role in controlling ductility (as measured, for example, by reduction in area in a tensile test) of a variety of materials. There is, therefore, considerable current interest in the mechanisms by which second phase particles affect ductile fracture. Experiments done by various workers have shown that second phase particles or discontinuities in the microstructure are potential sites for nuclea-tion of microcracks and of holes,6-l3 which then grow and cause premature fracture and the loss of ductility. Theoretical attempts have been made to explain the observed phenomena; most are able to explain observations qualitatively, but lack quantitative agreement. Much experimental work needs to be done to aid extension of theoretical models. A recent review article by Rosenfield summarizes work in this general area.14 PROCEDURE Material used in the previously described study on solution kinetics of cast and wrought 7075 alloy1 was also used in this study. Procedures for ingot casting, solution treating, and working were described in detail in that paper. Test bars were obtained for material of 76 initial dendrite arm spacing (11/2 in. from the ingot base) and 95 µ initial dendrite arm spacing (51/2 in. from the ingot base) for the following thermomechanical treatments (solution temperature 860°F; reduction by cold rolling). a) Solution treated 12 hr, reduced 2/1, 4/1, and 16/1. b) Solution treated 12 hr, reduced 16/1, solution treated approximately 5 hr after reduction. c) Same as a) except solution treated 24 hr prior to reduction. d) Same as b) except solution treated 24 hr prior to reduction. e) Same as d) except solution treated 20 hr after reduction. Test bars were taken both longitudinally and transverse to the rolling direction. Transverse properties are in the long transverse direction; since the final product was sheet (0.030 in. thick), properties in the short transverse direction could not be obtained. Test bars were flat specimens, of gage cross section1/-| in. by 0.030 in. and 1/2 in. gage length. After machining the test bars, they were given an additional 1/2 hr solution treatment of 860°F and aged 24 hr at 250°F. Three bars were tested for each location and thermomechanical treatment, after rejection of mechanically flawed bars. The average results of these three bars are reported. Elongation was measured using a $ in. extensometer and reduction in area was determined using a profilometer to measure the area after fracture. INFLUENCE OF THERMOMECHANICAL TREATMENTS AND SECOND PHASE ON MECHANICAL PROPERTIES Results of mechanical testing are presented in Figs. 1 to 4 and in tabular form in the Appendix. A general conclusion from results obtained is that details of the thermomechanical treatments studied were important only insofar as they influenced the amount of residual second phase. Figs. 1 and 4 show the longitudinal properties obtained (regardless of thermomechanical

Jan 1, 1970

By A. J. Heckler, J. A. Peterson

A capsule technique was successfully employed to investigate the effect of nickel on the activity of nitrogen in Fe-Ni-N austenite in the temperature range 600" to 1200°C. This technique consisted of equilibrating nitrogen among various Fe-Ni alloys within a sealed silica capsule. Nitrogen transfer among the specimens occurred by N, gas at 900°, lOOO? and 1200?C. Nitrogen gas pressures within the capsules were estimated to be as high as 22 atm. The activity coefficient of nitrogen, fN , in Fe-Ni-N austenite is adequately described by the linear interaction equation: log . wt pct Ni where the standard state is chosen such that fN = I as wt pct Napproaches zero in binary Fe-N. This relationship was determined over the temperature range 873" to 1473°K and for nickel contents of 0 to 35 wt pct. ALTHOUGH chemical thermodynamics of liquid iron alloys have been extensively studied, experimental data for the solid state are needed. These thermody-namic data will provide a basis for understanding phase transformations, precipitation reactions, metal-gas equilibria, and so forth. The interaction of sub-stitutional alloying elements with the interstitial elements is of particular interest. In this investigation the thermodynamic behavior of Fe-Ni-N austenite has been studied. The solubility of nitrogen gas in iron austenite is known to obey Sieverts&apos; law up to about 65 atm.1-6 In addition, the solubility of nitrogen in Fe-Ni austenite has been investigated5"8 using the classical method of equilibrating Fe-Ni alloys with nitrogen gas at 1 atm. A capsule technique similar to that used to study the activity of carbon in alloyed austeniteg&apos;&apos;&apos; was employed in the present work to determine the effect of nickel on the activity of nitrogen in Fe-Ni austenite over the temperature range 600" to 1200°C. EXPERIMENTAL PROCEDURE A series of Fe-Ni alloys up to 35 wt pct Ni was vacuum melted and cast into 1 by 3 by 6 in. ingots. Chemical analyses at the top and bottom of each ingot demonstrated that the ingots were homogeneous with respect to nickel content. The nickel contents are given in Table I. Additional chemical analyses showed that wt pct Si < 0.05, s < 0.01, C < 0.01, Al < 0.006, 0 < 0.004, Mn < 0.002, and P < 0.002. A 2 in. section of each ingot was cold rolled to 0.015 in. The material was then decarburized to a carbon content of less than 0.004 wt pct. A portion of the material of each nickel content was nitrided to various levels in a H2-NH3 gas atmosphere to provide a source of nitrogen during subsequent equilibration. The experimental technique consisted of equilibrating the series of Fe-Ni-N alloys in a partially evacuated sealed silica capsule at the temperature of interest. Both Vycor and quartz capsules were used. In general, the final equilibrium nitrogen content for each Fe-Ni alloy was approached from both higher and lower nitrogen levels. The criterion for establishing that equilibrium was attained was that the final nitrogen content for each Fe-Ni alloy was the same irrespective of the initial level. A schematic drawing of the sample configuration in a capsule is shown in Fig. 1. The samples were arranged so that there was a minimum of physical contact. The samples were also dusted with a fine, high purity alumina powder to help prevent sticking. Several different types of furnaces were used in this study. In each case, a thermocouple was placed immediately adjacent to the capsule during equilibration and the temperature was controlled to within *4?C of that reported. At each equilibration temperature, the following times were found to be more than sufficient to attain equilibrium: 600°C-250 hr, 900°C-150 hr, 1000°C-150 hr, and 1200°C-50 hr. After equilibration the capsules were quenched in water and the nitrogen contents of the specimens determined by a Strohlein analyzer. Analyses of samples after equilibration at 1000" and 1200°C showed no silicon pickup from the silica capsules. RESULTS AND DISCUSSION Transfer Mechanism. The mechanism by which nitrogen was transferred among specimens in an initially hydrogen flushed and partially evacuated capsule equilibrated at 1000°C was investigated. After equilibration the gas in the capsule was collected over water and an estimate of the pressure at temperature

Jan 1, 1970

By Frederick Rhines

PURE copper that has been allowed to oxidize at an elevated tempera-ture in the air is found to be covered with two distinguishable layers of oxide scale. The outer of these, which is very thin, is composed of cupric oxide, while the inner layer, comprising the bulk of the scale, is made up chiefly of cuprous oxide (Fig. 1a). If a small quantity of an alloying element, such as silicon, is present in the copper, silica particles are found disseminated through the cuprous oxide, deposited most abundantly near the metal surface, and, in addition, silica particles occur to a limited depth within the copper itself (Fig. 1b). It is this inner layer, composed of oxide particles precipitated in a matrix of metallic copper that is known as the "subscale" or the zone of internal oxidation. Under a low oxygen pressure it is possible to produce the subscale without the formation of external layers of copper oxides, thus leaving the metal surface bright and apparently clean while oxidation has occurred, in fact, to a considerable depth within the metal (Fig. 2). Although little is yet known in a detailed way of the mechanism of internal oxidation, the general nature of the process is evident. By virtue of the considerable solubility of oxygen in copper,1 it is possible to bring the alloying element in contact with oxygen within the metallic solid solution. If the oxide of the alloying element is more stable than cuprous oxide, the foreign oxide may form and, since most oxides are relatively insoluble in copper, it will not long remain in solution, but will separate as a precipitate. As the metallic solute is exhausted in the zone of precipitation, oxygen that is constantly being supplied at the surface diffuses farther into the alloy and thus produces an ever-thickening shell of subscale. The distribution of the reacting elements in the subscale and adjoining zones must be somewhat as indicated in Fig. 3. The conditions requisite to internal oxidation to be anticipated are thus: (1) a solubility of oxygen in the alloy, (2) the ability of oxygen to diffuse at an appreciable rate into the alloy, (3) the possibility of the

Jan 1, 1940

By J. B. Bassett, E. S. Rowland

INTRODUCTION THE experimental work reported herein was inspired by the publication of a paper by Grange and Stewart,1 in which it was suggested that at low chromium contents the effect of this element on the [M,] point was greater than at higher chromium contents. It was argued that, if a small increase of chromium in solution in austenite caused a sharp lowering of the [M,] point, it might lead to an explanation of occasional unsolved stress cracking of SAE 52100 during heat treatment. Commercial hardening is carried out at temperatures of incomplete solution, leaving carbides available to enrich the austenite during any inadvertent increase in temperature. Such enrichment of the austenite in chromium content would lower the [ M,] point nearer room temperature where cracking is more likely to occur. Accordingly, it was decided to investigate the effect of chromium, in quantities between o and 2 pct, on the[ M,] point of commercial steels. Fig I summarizes the data available on chromium steels. For purposes of comparison, the [M, ] temperature values were corrected by means of the Grange and Stewart formula§ to (I) Hypoeutectoid compositions: 0.50 pct carbon and 0.80 pct manganese (2) Hypereutectoid compositions: 1.00 pct carbon and 0.35 pct manganese. Only the steels having compositions reasonably close to these corrected values were included, because large adjustments inevitably introduce increased errors such as are experienced in using the formula. The straight lines of Fig I were drawn by the authors. These data obviously do not settle the question of the effect of chromium on the [M,] point, particularly at low chromium contents. While it is fairly well established that chromium causes the [M,] to be lowered when present in quantities of I pct or more, Grange and Stewart1 have suggested that in small amounts (less than I. pct) it is more effective in lowering the[ M,] point, while Klier and Troiano2 have suggested that in small amounts it is less effective in lowering the []M,] point. Payson and Savage3 concur with Klier and Troiano and further suggest that the effect is not linear at these concentrations. Rose and Fischer4 report that small amounts of chromium actually raise the-[M,] point of a 0.20 carbon steel. MATERIAL Two series of 35 lb induction heats were melted for this work, the analyses of which are given in Table I. One series was aimed at 0.50 pct carbon and 0.80 pct manganese with chromium additions in 0.25 pct increments from o to 1.5 pct with a single heat at 2.0 pct Cr. This series was considered necessary because the commercial heat treatment of SAE 52100 does not generally introduce more than about 0.60 pct carbon in solution in the austenite. The high

Jan 1, 1948

By H. Landsberg

THE curriculum presented here is an outgrowth of discussions by the Committee on Geophysics Courses of the A.I.M.E. in previous years. It had to be a compromise between the desires voiced by employers of geophysicists, professional geophysicists and the possibilities at an average college. There one has to face the questions of the available teaching staff, the inertia of administrators and teachers set in their ways, and the red tape involved in modernizing antiquated curricula. It is, of course, not ideal to have colleges and universities lag 10 years behind the times. Rather, instead of being prodded by industry, -they should be ahead of industrial needs. There should also be a certain amount of leeway for the student in any college curriculum. All these points had to be considered in drawing up a curriculum, which, instead of being narrowly termed "geology" or "geophysics" was rather called "earth science." It gives the student a chance to specialize in one of the various branches represented by teachers on the faculty of The Pennsylvania State College, giving as options Geology (with subdivisions of Mineralogy and Paleontology), Geophysics, Geography, and Meteorology. Table IA. represents the option of geophysics in the curriculum that envisages that a student may want to make his career in any of the fields encompassed by the American Geophysical Union or in geoexploration. This is, of course, only the start of an education that in most cases will have to be followed by graduate work for complete professional training. The outlined curriculum is definitely of an engineering type and is identical for all of the four options mentioned for the first two years. Specialization will start in the junior year but even thereafter the branches are kept as closely allied as feasible in order to permit a student to change from one to the other (e.g., because of a different aspect in the employment situation) with a minimum of additional work. Table IB shows the geophysics option according to subject matter, indicating the considerable amount of work in the fundamentals of mathematics, physics and chemistry with a liberal number of geology courses, and some engineering. The courses in the field of geophysics are limited-just two lecture courses as a general introduction and one field course, to permit the student a visualization of the correlation between mathematically analyzed physical data and the geological realities. Thesis work is considered essential to teach the student, while he is still in college, some things S. F. Kelly has mentioned as desirable: (I) following of instructions for somewhat independent work; (2) organizing of material, and (3) producing a readable report. This, together with the personal contact with the advising faculty member, will help in forming a student&apos;s personality. The seminar course attempts to get the student into the habit of reading current literature, so that he can keep abreast of the times.

Jan 1, 1941

By Arthur L. Christenson, Clarence E. Jackson

IN the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition1 may be corrected to the grain size observed in an actual weld,2 or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.3 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2100°F. has been used. In studies of the end-quench hardenability specimen quenched from 2100°F. instead of from a lower temperature of 1700°F., it is important to ascertain the relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6,7 French has considered this effect from both theoretical and experimental aspects. In French&apos;s studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been proposed: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching. temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1943

By R. P. McLaughlin

Discussion of the paper of R. P. McLaughlin, presented at the San Francisco meeting, September, 1915, and printed in Bulletin &apos;No. 108, December, 1915, pp. 2313 to 2319. M. E. LOMBARDI, Berkeley, Cal.-Mr. Bell, I would ask you to state before the meeting what you said to me the other day, about the final recovery of oil from oil sands that have become inundated with water. A. F. L. BELL, San. Francisco, Cal: In stating my opinion, I give it with certain qualifications. In the Kern field, and possibly in some others, I think we will eventually get all the oil out, whether the water comes in or not, since it is peculiarly constructed, being in the form of a partial dome. In 1909, while I was field manager of the Associated Oil Co., I installed some large air compressors to handle the water. At that time the oil had migrated to the higher and more shallow portions of the field, because the water had inundated the deeper sections. The result was that the shallow districts within the center of the dome were in many, cases producing as much or more oil per well than the deeper wells. And in the inundated sections the water had slowly spread over large areas, so that nothing but water was pumped from them. Under these conditions, we decided to pump the wet. well with air, and installed four 2,000-cu. ft. compressors. The air was compressed and forced into the wet wells at, about 250 lb. pressure. Shortly the inundated district that had produced almost all water and only about 150 bbl. of oil a day increased its production to over 2,000 bbl. of oil per day. It was not-long before, we noticed that the production of the shallow territory was falling off to such an extent that in many cases the wells were abandoned; at the same time the area of the water-inundated district was greatly reduced, showing that when the water pressure was reduced the oil migrated back to the lower depth. The wells which at first had had the air jets put into them finally produced so much oil that we had to take the &apos;air jets out and return to the use of the beam pump, because it is not commercially feasible to pump, an oil of 14° gravity with air. To handle such oil profitably by air, it must carry with it 50 to 90 per cent. of water. The results have led me to believe that oil monoclines, where there is a gradual rise to a certain point, or in plunging anticlines, even though water gets into oil sands, eventually we get the larger percentage of the oil. However, the man with a small acreage in the deeper sections may find some morning that his oil has gone, another man in some higher portion of the district having gotten it.

Jan 12, 1915

By Wm. E. Milligan

DESPITE the zero weather of Monday, the morning meeting on nonferrous ore-reduction metallurgy got under way promptly under the efficient control of Arthur A. Center. The first and third portions of the paper on the Tri-State region were presented by B. M. O&apos;Harra, with R. H. Lowe substituting for co-author Illidge on the second part. Attention was drawn to the compact design attainable when "Sink and Float" was employed as a means of primary concentration. The teaching profession should welcome this concise correlation of data from such a renowned center of lead and zinc production. H. R. Hanley and C. R. Hay¬ward were much interested in the mechanics of charging, manufacture, and life of the retorts.

Jan 1, 1943