Search Documents

By Webster, Wm. Reuben

THE greatly enlarged demand for small sizes of seamless copper tube which has recently occurred, due particularly to the rapid growth of the electric household-refrigerator industry, has emphasized the superiority of phosphorized to tough pitch copper for the purpose of producing this commodity. In the manufacture of this material exceedingly heavy reductions by cold drawing are employed, customary practice involving as much as 90 per cent. reduction of cross-sectional area in four runs without intermediate annealing. Although this superiority has long been recognized by tube makers, no quantitative expression of it has heretofore been published. It is believed that the data herewith presented mill serve this purpose. Recent investigators are not in agreement as to the relative mechanical properties of copper containing small amounts of oxygen as compared with copper containing sufficient oxygen to produce that condition known as tough pitch. Hanson, Marryat and Ford1 found that "oxygen has a relatively small effect on the properties of copper." Johnson, on the contrary, states "it cannot be denied that it (tough pitch copper) is inferior to deoxidized copper . . . where severe mechanical manipulation is concerned." These authorities in the reports of their investigations, as might be expected from their conclusions, do not present data of a character requisite to a conclusive determination of the question.

Jan 1, 1927

By John C. Calhoun, Frank T. Bethel

The application of a method for analyzing pressure build-up curves to determine the effective permeability in the Spraberry is presented. Sixteen upper Spraberry wells of the Driver area arc analyzed and show variations in the in-place effective permeability of 2 to 183 md. Since these value- are much larger than the .5 md. or less reported for the matrix rock. a large part of the vertical fractures noted in Spraberry cores- must be considered native to the formation. The effectiveness of the well fracture treatment in connecting the well bore to the native fracture system is analyzed by comparison of the effective permeability as determined from the PI test to that obtained from a pressure build-up curve. These results show that the fracture treatment is sufficiently effective in connecting tile well bore to the native fractrure system to yield a flow capacity within about 50 per cent of that dictated by the native fracture system About two-thirds of the wells show some degree of local blockage. INTRODUCTION Fractured reservoirs have been known in the past.' However, during the past two years the Spraberry formation has directed the attention of the petroleum industry to a study of the performance of a fractured reservoir. The large variation in the number of fractures noted in Spraberry cores rile large variation in the producing ability of offset well.. the dramatic effect of well treatment on well ,productivity. the unknown quantity of oil stored in the fractures and matrix rock. and the unknown oil to be recovered were part of the initial Spraberry puzzle. In this type reservoir where the well treatment is an important factor in determining the productivity. it i- particularly desirable to determine the in-place flow capacity of the drainage area at distance* far removed from the well bore. This value. when compared to the flow capacity obtained from a PI measurement, will show the effectiveness of the well treatment (completion. fracture treatment, acidization. etc. in establishing a flow capacity in the vicinity of the well bore equal to that in the more remote region. The object of this paper i.; to show the application of a method of pressure build-up analysis for this purpose in studying the Upper Spraberry formation in the Driver area. STATEMENT OF THEORY The theoretical basis for the application of a pressure buildup curve to show the effective permeability of the rock at distances far removed from the well bore has been presented in detail in earlier publications.', in the previous development it was shown that pressure build-up behavior of all wells could be reduced to the same dimensionless build-up curve of Fig. 1. This mean.; that the bottom hole pressure of a well after hut-in will rise in such a manner that a plot of pressure against the logaritllm of time yields a straight line. The slope of this linp can be rlzed to calculate the effective permeability as expressed by the following equation: where: effective oil permeability md oil production rate prior to shnt in. STB/I) In practice the flow which occurs into the well bore after shut in and the variation in flow capacity in the immediate vicinity of the well bore usually cause the early part of the build-up curve to be unsatisfactory in the determination of permeability. In general the effect of these factors on the straight line section will become negligible after a time when the of the following equation is equal to 0.1. and the preferred section Of the curve for use in defining the slope lie-

Jan 1, 1953

By H. E. Criner, M. G. Driessen

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By M. G. Driessen, H. E. Criner

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By A. E. Anderson, H. J. Hilll

Laboratory data for 155 field muds and 77 .shales have been used to develop correlations to estimate the net streaming potential component of the SP. Analysis of these data and comparison with field tests show that streaming potential corrections must be made to obtain an accurate estimate of the electrochemical potential for use in the determinntion of formation water resi-iiviy. The self-potential curve is related to formation water resistivity, and considerable effort within the oil industry has been directed toward clarifying this relationship. The Schlumbergers and Leonardon1,2 recognized that two types of potentials, electrochemical and electro-kinetic, resulted in the net potential variation in the borehole. Most of the later papers have dealt with the electrochemical component and its controlling parameters. The investigations of Wyllie,2" Salisch' and Moore5 provide the most extensive sources of data on streaming potentials across mud cakes. These authors observed streaming potentials of sufficient magnitude to be of critical importance in SP interpretation, if it is assumed that streaming potentials develop only opposite permeable beds. Streaming potentials across shales have been reported by Schenck and by Gondouin, et al.7 Since SP magnitude is the difference in potential opposite shale and sand beds, these authors suggested that the net streaming potential component may be negligible. The present investigation was initiated to evaluate empirically some of the parameters controlling the magnitude of the net borehole streaming potential and to determine whether useful relations between mud properties and net streaming potential could be established. Field muds were used in this investigation. These muds were characterized by the amount and type of chemical treatment utilized for five days before Sampling. Filter loss, mud resistivity, mud density and filtrate resistivity were determined for each mud with conventional methods and apparatus. Mud filtrate pH was estimated with Hydrion pH paper for the appropriate range. Streaming PotentIals Across MuD Cakes Commercial calomel-saturated KC1 electrodes are subject to potential changes attributed to contamination of the very small fiber-tip bridge by particles of clay from the drilling mud.3 To minimize this difficulty, a large diameter bridge (Fig. 1) was constructed with saturated KC1-agar gel and a filter disc of microporous porcelain. Experiments showed that streaming potentials across this bridge are less than 0.2 mv at pressure dif-

By Charles Hart

In this paper it is the author's intention to show the extent and character of foreign ores now known to be available; these deposits may be in active production or held in reserve until economic conditions may make them active. He hopes to show the relation existing between these ores and the American supply, and which of the former are now producing or will in turn come into production when our better ores have been exhausted. This phase of this discussion must of necessity include some data as to the present rate of consumption and a study of the changes we may expect here and abroad in the general steel trade and its sources of supply in raw materials. It is obvious that the occurrence of coal, ore and limestone in relation to one another and the proximity of a market are the elements in control of this feature of the problem. If the foregoing situation is favorable, all the other questions may be solved, for it is clear that with proper basic conditions finance, labor and operations will fall in line. We present a short outline of the present methods of carrying on the foreign iron ore trade, believing that it is of general interest in comparison with our own highly specialized methods, and that with the exhaustion of our better ores we will be compelled to seek a part of our supply abroad. A partial list of iron ores, with incomplete analyses (Table I), is added, to give a better understanding of the general situation and explain to some extent the reason for things being as they are in the iron and steel trade of the world and to help in bringing this paper to an informing conclusion. The question of the world supply of iron ores has been a subject for study on the part of geologists and engineers for many years, and found its best results in the Eleventh International Geological Congress, appropriately held at Stockholm, Sweden, in 1910. The proceedings are published in two volumes and are undoubtedly the best records available on this subject at the date of publication. It should be borne in mind, however, that much has happened in the 20 years since these figures were assembled. There is just as much known ore at present as at that time, minus the quantity consumed, plus newly discovered reserves. The World War had great effect upon this situation; during that time explorations were greatly reduced and the settlements after the

Jan 1, 1929

By J. C. Martin

Stmplified equations are developed for the flow of fluids in gas drive reservoirs in which the effects of gravity can be neglected. The results show that the pressure distribution is governed by a nonlinear heat flow type of equation, and the saturation distributions are related to the pressure by the same equations QS those developed by Muskat for the average pressure and saturations in gas drive reservoirs. Unrler certain conditions the equation for the pressure can be approximated by the linear form of the heat flow equatlon. This equation tk analogous to the equation for the pressure in single-phase compressible flow The analysis reveals that the equation for the pressure in n~ultiphase flows can be obtained directly from the equation for the pressure in slngle-phase flows by simply replacing the single-phase compressibility by the total compressibility and the single-phase mobility by the sum of the mobilities of all the fluids present. Perrine's method of pressure buildup analysis for multiphme flows is based on these same substitutions. Thus, the development presented in this paper constitutes a theoretical justification for Perrine's method of pressure buildup analysis. One of the most difficult problems associated with the production of oil is the determination of the flow of the fluids within the reservoirs. One purpose of this paper is to present the development of simplified equations for the flow in gas drive reservoirs. The other purpose is to present some of the needed theoretical foundation for the methods currently being used in the analysis of multiphase pressure buildup data. The analysis presented in this paper makes use of a partial linearization of the equations governing multiphase flows. It is felt that the process of linearizing or partially linearizing the nonlinear equations of multiphase flows can lead to useful results since this process has proved extremely valuable in the study of other fields of science and engineering where nonlinear equations are encountered. Pressure buildup data of shut-in wells have been used for many years to estimate the static reservoir pressure. These data have also been used in studying the aver- age permeability both away from and close to the well-bores. The majority of the buildup data are obtained from wells producing two or three fluids. As yet the theoretical foundations for the methods of buildup analysis used in connection with rnultiphase buildup data have not been established. A number of methods of analysis of pressure buildup data have been developed." Most of these methods apply only to single-phase flows, and almost all of the theoretical analysis is confined to single-phase flows. Perrine' developed a method of analysis for rnultiphase flows from the method for single-phase flows of Miller, Dyes, and Hutchinson.' He did this by simply replacing the single-phase compressibility by the multiphase compressibility and replacing the single-phase mobility by the sum of the mobilities of the fluids in the rnultiphase flows. Obviously, such a procedure lacks a certain amount of theoretical justification, and such practices can lead to erroneous results. Fortunately, Perrine's results have a theoretical justification, and this justification is presented in the following discussion. It is assumed that gravitational effects and the cornpressibility of the rock can be neglected. Under these assumptions the equations governing the simultaneous flow of gas, oil and water in porous media areo* The preceding equations can be expanded into the following expressions.

By E. H. Boswell, E. M. Cushing

The Mississippi embayment east of the Mississippi River is part of a vast geologic and hydrologic province. The abundance of water available is largely responsible for the agricultural history of the area and is perhaps the key factor in the rapidly accelerating trend toward industrialization. The multiple artesian aquifer systems that underlie the region and the alluvial aquifer along the Mississippi River are virtually undeveloped sources of fresh water in that they are yielding only a fraction of the water available. The potential yield of the 12 aquifer systems is estimated to be about 25,000 mgd (million gpd) of which only about 600 mgd is presently being withdrawn. The amount of water in storage in these systems is about 1600 trillion gal. Ground water having a dissolved-solids content of less than 500 ppm is generally available at depths of less than 1000 ft, and water having a dissolved-solids content of less than 1000 ppm is available in some places to depths of more than 3000 ft. Iron is the most common troublesome chemical constituent in the ground water. Water in varying amounts is also available from streams within the region. The amount of water which originates within the region and which leaves it as streamflow during a year averages about 50 million acre-ft (about 45,000 mgd). An additional 375 million acre-ft (about 340,000 mgd), which originated outside the region, leaves the region as streamflow during an average year. Some streams have considerable flow during periods of no precipitation and the water during these periods generally has a low dissolved-solids content. Large quantities of water from streams and waterbearing sands (aquifers) are available in the Mississippi embayment east of the Mississippi River. Most of the region is underlain by aquifer systems that will yield large quantities of water to wells, making ground water the most readily available source of fresh water. About 90% of the water used in the region is obtained from wells. Streams have been used primarily to dispose of, and dilute, wastes that have been dumped into them. The Mississippi, Ohio and Tennessee rivers, and the lower parts of the Tombigee and Yazoo rivers also serve as a means of transportation. This nominally water-rich region receives from 48 to 56 in. of precipitation in average years and is crossed by several large rivers. The largest, the Mississippi River, is the western boundary of the region discussed in this paper. The economy of the region is basically agricultural, but industry has become increasingly important since World War 11. The diversification and mechanization of agriculture have resulted in a surplus of manpower, most of which is being absorbed by the expansion of industry. Further industrial expansion probably will occur because of the available manpower, natural resources and economical transportation. Increasing demands on available water supplies will be made and the future economic growth of the region will be largely dependent upon wise utilization and management of the water resources.

Jan 1, 1969

By K. H. Coats, M. H. Terhune

Analysis and example applications have been performed to compare the accuracy and computing speed of alternating-direction explicit and implicit procedures (ADEP and ADIP) in numerical solution of reservoir fluid flow problems. ADIP yields significantly greater accuracy and requires about 60 per cent more computing time than ADEP, not 300 or 500 per cent more as reported elsewhere. l,2 INTRODUCTION Several recent papers 1-3 discuss an alternating-direction explicit difference approximation (ADEP) to the diffusion equation. Example applications of ADEP and ADIP4 were reported to support conclusions that ADEP is comparable in accuracy to ADIP and requires one-fifth to one-third the computing time of ADIP. Applications of ADEP in calculation of two-phase flow in reservoirs was also proposed. 3 This study was performed to compare further the relative merits of ADEP and ADIP in simulation of two-dimensional flow of one and two fluid phases in reservoirs. Since two-phase flow equations are often essentially elliptic rather than parabolic, the efficiency of ADEP in solving the elliptic equation was also examined.

Jan 1, 1967

By Pol Duwez, Spencer R. Baen

A LTHOUGH the practical importance of Fe-Cr--iV Mo alloys has long been recognized, constitution studies have been limited to a few alloys within rather narrow ranges of composition. The purpose of the present study was to establish the phase boundaries in the ternary diagram at a temperature of 1200°F (650°C).* The identification of phases and the determination of phase boundaries were based primarily on X-ray diffraction measurements and occasionally on microscopic observation. The methods used for locating the phase boundaries were essentially those described in detail by Andersen and Jette,' and by others.', The compositions of 180 alloys, prepared by powder metallurgy techniques, are shown in Fig. 1. The chemical analysis and mesh size of the powders which were used for the preparation of the alloys are given in Table I. The powders were mixed for 48 hr or longer, then compacted under 80,000 psi in a %-in. diam steel die. Each specimen weighed approximately 5 g. The compacts were sintered for 4 hr at 2500°F (1371°C) in an atmosphere of pure dry hydrogen (dew point near the temperature of liquid nitrogen). An open tray of chromium powder was placed upstream of the compacts to act as a "getter" for the last traces of oxygen or water vapor. In many cases this chromium powder was bright after sintering. Occasionally the upstream side of the powder was slightly greenish, but in all cases the downstream side was metallic. Some of the alloys contracted during sintering and some expanded as much as 20 pct. The latter alloys, which in all cases were brittle, were crushed in a tool steel mortar, repressed, and resintered for 4 hr at 2500°F. After sintering, the alloys were aged for ten days at 1200°F (650°C) in evacuated (105 mm Hg or better) fused silica tubes and were cooled rapidly to room temperature following the aging treatment. The use of the powder metallurgy technique in preparing alloys for structural investigation offers a simple method 'of avoiding contamination or non-homogeniety which could result from a melting operation. It is very often possible to dispense with chemical analysis of the alloys which have been prepared by the powder metallurgy method. In lieu of chemical analysis, it is necessary to determine the weight of the compact before and after sintering. The chemical composition of the alloy may be considered as that of the green compact, within the limits of accuracy determined by the loss of weight during sintering. In phase-diagram studies it is important to achieve homogeniety in structure, whether the alloys are prepared by powder metallurgy or by melting. Homogeniety means complete diffusion during the sintering of the alloys which are prepared by powder metallurgy. It has been found from experience that the best criterion for establishing the completeness of diffusion is the sharpness of the X-ray diffraction patterns. This criterion has been used throughout the present study. The X-ray diffraction data were obtained using powder cameras of either 214.86 or 71.62 mm diam. Copper, cobalt, or chromium Ka. radiation was used, the choice being based on the alloy composition. The powder samples were obtained by filing or crushing, depending on whether the alloy was ductile or brittle. In some cases, the powder was annealed for 4 to 6 hr at 1200°F in vacuum. The measurements were corrected for film shrinkage and absorption. The large camera, in which the film is mounted

Jan 1, 1952

Who's Who in Mineral Engineering - The 1979 Directory of the Society of Mining Engineers of AIME

Jan 7, 1979

By Joseph C. Buchen

IN principle, production of salt from sea water is a simple operation. Sea water is trapped in ponds, the sun and wind cause evaporation of the water, and what is left is principally salt. Commercial production of solar salt, however, requires a careful consideration of many factors. Obviously, sufficient evaporation must take place throughout the making season to produce an economically adequate crop. Other factors are density of soil, contour of ground, height of ground above sea level, minimum dilution from fresh-water streams, and distance from market. Unfortunately, in the United States the localities of greatest evaporation, allowing for the other factors, are not the most suitable for the manufacture of sea salt by solar evaporation. The south end of San Francisco Bay most

Jan 1, 1937

By H. W. Gillett

MAINTENANCE of membership by the technical so¬cieties and the activity of these societies in spite of the adverse business situation have been noteworthy. This forcibly brings home the fact that industry recognizes that sound technical guidance is well worth its cost. The numerous difficulties and losses due to defects of various kinds arising from gas-metal reactions are now generally recognized and interest in these problems is widespread. The forthcoming A. I. M. E. round-table discussion of gas-metal problems will do much to clarify the situation and will permit us to assay our present knowledge and to suggest the proper direction for profitable future research. "The Age Hardening of Metal" was the title of the annual I. M. D. lecture delivered by Dr. Paul D. Merica. A critical review of the known facts relating to age-hardening phenomena was first given, followed by the presentation of a theory correlating the detailed observations which have been made regarding the mechanism of the hardening.

Jan 1, 1933

The growth and influence of Sherritt Gordon Mines Ltd. in the nickel producing industry has been quite phenomenal. Although the company's Lynn Lake deposit in Manitoba was actually dis- covered in 1941, it was not until 1945, when men and materials were more readily available as a result of the end of World War II, that the area was staked and news of the discovery leaked out. As a result of the discovery, Professor Frank Forward of the University of British Columbia was commissioned by Eldon Brown, then President and Man- aging Director of Sherritt, to develop a new nickel refining process. A pilot plant, based on the results of Professor Forward's research, was constructed in Ottawa, and after the successful testing of the Lynn Lake ore, Chemical Construction Co. was given a con- tract in 1952 for construction of a producing plant. By 1954, the Fort Saskatchewan refinery was operating at an annual production of 15 million lb of nickel metal in the form of briquetts or powder. Capacity has since been increased to 30 million lb.

Jan 10, 1968

By M. V. Mielke, R. E. Hagen, R. L. Bennett

FINE IRON ORES, and concentrates such as those produced from taconite, must be converted to lump form by some process of agglomeration before they can be used effectively in the blast furnace or open hearth. At the present time, four major processes for agglomerating these materials are being used on a commercial scale: sintering, nodulizing, pelletizing and briquetting. IN 1945 U. S. Steel Corp. through its subsidiary the Oliver Iron Mining Div., drew up tentative plans for an agglomerating plant on the Mesabi Range which would include a nodulizing kiln and a sintering machine. The purpose of the plant was two- fold: during its initial operation it would provide data on agglomeration of high grade ore fines, and would help relieve the shortage of ore for open hearth charging. Subsequently, it would be available for agglomerating taconite concentrates. While operating on fines screened from direct ore, it was planned to develop techniques and personnel so that a workable plant would be ready to handle taconite concentrates when the time came.

Jan 1, 1954

By John A. Gann

THE Iron and Steel Division has shared in the general increased activity of the industry. The fall meeting at Chicago was not only well attended but particularly characterized by the virility and scope of the discussions at the various sessions. The program for the February meeting indicates a similar interest in technological developments. The Blast-Furnace Committee continues to have the hearty support of the industry with discussions of such a nature as to be of real help to the operator as well ass the technologist. The work of the Open-Hearth Committee continues to be outstanding, with ever increasing attendance and ever mounting interest in the meetings. Formation of a conference on the physical chemistry of steelmaking has given those interested in this phase of work an organization allowing the same

Jan 1, 1936

By John Chipman, Peter J. Koros

The distribution of copper between liquid silver and liquid iron, Fe-C, and Fe-C-Si alloys was studied at 1600°C. From the data and the activity of copper in silver obtained from the phase diagrams, the activity coefficients of copper in iron up to 3 atomic pct are log y, = 0.90 — 2.4 N, and y": = 8.0. The effect of carbon up to saturation is expressed as log y = 1.8 Ni. The effect of silicon up to 11 atomic pct is insignificant. SLOWLY rising copper content of steel being produced is focusing attention on the lack of information on the behavior of copper in liquid steel. Chou' measured the activity coefficient of copper in liquid iron through its distribution between liquid silver and iron. He obtained a value of 9.12 at infinite dilution. Chipman' calculated the activity coefficient of copper in liquid iron at 1600°C from the phase diagram and obtained a value of 12. Ameiln and Pfeiffer- investigated the possibility of removing copper from liquid steel through the use of lead, silver, and bismuth as solvents. They also calculated that the activity coefficient of copper in liquid iron would be increased five or sixfold by addition of 4 pct C. Langenberg and Lindsay' are investigating the effectiveness of lead and sodium sulfide in removing copper from liquid iron. The experimental method was similar to that used by Chou' and Chipman and Floridis." Silver, copper, and iron were melted together, the copper distributing itself between the two layers so that at equilibrium a,.,, (in Ag) - a,.,, (inFe) and N,.,, (in Ag) yc,, (inFe) (in Ag). [21 N,.,, (inFe) Thus, from the concentration of copper in each layer and the activity coefficient of copper in liquid silver, the activity coefficient of copper in liquid iron can be calculated. The effect of an alloying element such as carbon on the activity coefficient of copper can also be determined from its effect on the distribution, provided the new element is essentially insoluble in silver. The one serious limitation of this method is the increasing mutual solubility of silver and iron in the presence of a third component. The mutual solubilities of pure iron and silver are negligible, but increase with increasing copper concentration beyond the range investigated. Ag-Cu System—The activity coefficient of copper in silver at 1600°C had to be estimated, since direct experimental data are not available. Kawakami" measured the heat of mixing of Ag-Cu alloys at 1200°C by a calorimetric technique. Scheil' calculated the heat of mixing in this system by use of the phase diagram, assuming that the solution is random and that the heat of mixing is independent of temperature. The terminal solid solution may be assumed to obey Raoult's law within the requirements

Jan 1, 1957

By C. M. WEILD

ATTENTION has been turned recently to the exploration and development of certain large blanket-deposits of brown iron-ore in Cuba. The most conspicuous of these to-day, and the one upon which the most light has been shed, is the Mayari deposit, situated about 15 miles south of Nipe bay. Here the Spanish-American Co. has sole control over 18,500 acres of ore-bearing lands, reported by its engineers to contain 500,000,000 tons of ore; and the necessary plant and equipment, with docks and railways, is now under construction for the early marketing of this ore. A similar deposit, and undoubtedly the next to be exploited, is the ore-field at Moa bay, where 13,000 to 15,000 acres of ore-lands, immediately adjacent to the shores of an excellent harbor, have been generously covered by numerous mining-claims, practically all controlled by four large interests. This deposit is now estimated to contain approximately 350,000,000 tons, on the basis of dried ore ready for shipment, a figure which may be increased when the western limits of the ore-deposit have been more accurately defined. Other deposits of the same type, but smaller and less accessible, are those at Cubitas, situated from 12 to 15 miles north of Camaguey city, and at Taco bay and Navas, points lying a few miles west of Baracoa. The area of the Cubitas deposit is said to be 6,000 acres, and the yield of ore is estimated at 150,000,000 tons. The Baracoa. deposits are less well known, but preliminary estimates have placed their joint ore-reserves at 40,000,000 tons. Accepting the above tonnages as reasonably correct, we conclude that the deposits enumerated give promise of adding about 1,000,000,000 tons of iron-ore to the world's supply; they have, therefore, to be considered in any attempt to fore-

Aug 1, 1909

By J. E. Warren, J. H. Hartsock

An asymptotic solution to the equation that describes the flow of a slightly compressible fluid in an infinite porous medium has been used to estimate the interaction between two adjacent wells producing from a common reservoir. A direct method for approximating the interference time defined by Stevens and Thodosl has been suggested. An alternative definition for the time of interference, based on the minimum pressure change in the interference region, has been proposed; also, a direct method of determination has been prescribed. Examples have been employed to illustrate the use of both methods.

By Marius R. Campbell

VARIOUS classes of coals are recognized in this country at the present time. These classes depend largely upon physical characteristics rather than upon chemical composition, and consequently they cannot be accurately defined. The divisions into anthracite, semi-anthracite and semi-bituminous are fairly satisfactory; but the term bituminous embraces so large a variety of coal that it is of little value, and the term lignite is so loosely applied that it has little or no place in a scientific classification. At present there is no way of accurately defining the vari¬ous classes of coal, because no adequate scheme of classification, which applies to lignites as well as bituminous coal and anthracite bas been proposed. The object of this paper is to present such a scheme, which is based upon data obtained dur¬ing the past year by Prof. N. W. Lord,1 in charge of the chemical laboratory of the United States Geological Survey coal-testing plant at the Louisiana Purchase Exposition, St. Louis. All the classifications of coals proposed prior to 1877 were based either on physical characteristics or on proximate analyses, including all of the impurities. These schemes were illogical and highly unsatisfactory, for the physical properties of a coal give little indication of its true composition; and impurities, such as ash and sulphur, are largely the results of acci-

Sep 1, 1905