Search Documents

By A. Madrazo

The Standing-Katz method for predicting liquid densities of reservoir fluids has been tested using experimental data of 154 bottom-hole or recombined reservoir fluid samples. New pressure- and temperature-correction curves for the Standing-Katz type correlation are presented which improve the accuracy of prediction. INTRODUCTION The present study was undertaken to investigate the known methods of determining liquid densities and to select one of them which might yield a better correlation if additional data were employed. An appropriate correlation would incorporate the following characteristics: (1) ease of handling in the computations, (2) results within engineering accuracy and (3) data easily accessible. After careful investigation of the different methods, the Standing-Katz correlation1 appeared to have these characteristics. The Standing-Katz correlation for liquid densities of hydrocarbon systems is based upon limited data. The original work, which employs apparent densities for methane and ethane, was based on data of 15 saturated crude oils in equilibrium with natural gas. Therefore, a test of the correlation using additional experimental data would serve either to validate the Standing-Katz correlation or to form a basis for corrections if such were necessary. PROCEDURE AND GRAPHICAL SOLUTION The data of 154 bottom-hole or recombined reservoir fluid samples were employed to calculate the densities at 14.7 psia and 60°F by the method described in Table 1. Volume contributions for methane and ethane were assigned from the pseudo liquid density plot (Fig. I), but volume contributions for N2, CO2 and HzS were not considered. The densities computed at reference conditions of 14.7 psia and 60°F were then elevated to their respective temperatures and pressures by the use of the correction curves proposed by Standing.' The percentage differences between the experimental values and the calculated values were determined; these samples were grouped into temperature, pressure and density ranges to determine a possible trend. It appeared that, at temperatures above 160°F, the calculated density values were consistently larger than the experimental density values; however, no obvious trend was found for the density and pressure ranges. There is a relationship between the pressure-correction and temperature-correction curves. This relationship, embodied in the temperature-correction curve, can be expressed as follows. The experimental densities of 125 samples above their bubble points were known. From these isothermal data, it was possible to determine an experimental-density difference between two pressures; and (from Fig. 2*), a calculated density difference between the same two pressures was determined. The relative effect of temperature must be considered in the calculated-density values. The effect of temperature can be determined by entering Fig. 3* at the two densities in consideration and obtaining the change in density at constant temperature. This change, or delta density, must be added

By A. R. Gregory, M. R. J. Wyllie

The literature reveals that scant attention has been paid to the systematic experimental determination of the formation factors of unconsolidated porous media. No experiments appear to have been made on the effect of increasing cementation on the formation factor of an initially unconsolidated porous medium. Measurements have accordingly been made of formation factors as a function of porosity for aggregates of spheres in the porobity range 12-56 per cent and of cubes, cylinders, discs and triangular prisms in the porosity range 30-45 per cent. The results are examined in the light of the theoretical equations of Clerk Maxwell. Fricke and Slawinski. Aggregates of unconsolidated spheres and beach sands have been artificially cemented with silica and the formation factor-porosity relationships determined. A theory is outlined which seeks to explain the results obtained and which postulates that formation factor and porosity data for consolidated sandatones may be used to determine the original porosity of the unconsolidated sands from which the consolidated sandstones were derived. It follows also that for consolidated sandstones F' = C where F is formation factor, fractional porosity and C and k are constants. INTRODUCTION All schemes of electric log interpretation implicitly or explicitly require the use of formation resistivity factors or? as they are now generally called. formation factors. 'The originator both of the concept of formation factor and of the use of formation factor data in electric log interpretation was Archie.' More recently it has been suggested that formation factors are of value in describing fluid flow in porous media. A full discussion of this problem together with adequate reference.: has been given by Wyllie and Spangler.' In spite of the theoretical and practical importance of the subject, there appear to be remarkably few basic formation factor data in the petroleum literature. A wider search reveals that this situation is nut confined to the literature of the to industry. at various times over the last century, attempts have been made to compute the theoretical relationship between the formation factor and porosity of simple systems of unconsolidated particle.. However. the formulae derived are not all identical and the experimental evidence adduced in support of each i; not wholly convincitng. Most of the experimental work has been carried out on system. of unconsolidated spheres, although some attention has been given to systems of spheroids and cylinder. Other simple shapes have received neither theoretical nor experimental investigation. The writers feel that a better understanding of the formation factors of complex systems of practical importance requires a firm foundation of reliable experimental data applicable to simple systems. Accordingly, they have reviewed the relevant literature and have determined experimentally the relationship between the formation factor and porosity of unconsolidated aggregates of particles of regular geometrical shapes. Some experiments have also been carried out to investigate the effect of cementation on the formation factor-porosity relationship. PREVIOUS WORK Although the term formation factor was not used. the relationship between the resistivity of a solution containing dielectric solids and the resistivity of a similar solution not containing solids is an old and important problem. The formation factor of a system of dispersed spheres as a function of porosity was considered by Clerk Maxwell. Maxwell arrived theoretically at the following expression: where F is formation factor and fractional porosity. Lord Rayleigh' also examined the problem of the formation factor of systems of spheres and cylinders and concluded that for spheres Clerk Maxwell'.; expression gave a value of F whirl]. at low porosities particularly, was too small. However,

Jan 1, 1953

By Donald B. Hunter

The Ti-Be system up lo 10 wt pct Be with cortlmercialll' pure titanium has been determined using metal-lographic techniques. Beryllium forms the p eutec-toid type of dinqarz with titanium; the eutectoid occurs at 0.5 xt pct Be azd 1500 F, while an eutectic is foritled at 1887°F containing between 5 and 7.5 rt pct Be. The solubility of beryllium in a titanium does not exceed 0.05 zvt pct and the maximum solubility of Beryllim in 0 titanium is 1 wt pet. PREVIOUS work on the Ti-Be phase diagram indicated that additions of beryllium to titanium resulted in a marked lowering of the melting point,''' and it was also observed that the solubility of beryllium in both a and p titanium was retricted.- With the limited data available, McQuillan and McQuillan constructed a partial hypothetical diagram of the Ti-Be system,= assuming that beryllium formed the 0 eutectoid type of system with titanium. Subsequently Bedford published a tentative diagram of the entire Ti-Be system: although he did not investigate alloys containing less than 10 wt pct Be. This diagram included several compounds described by other authorities.'-l3 The following account describes work directed toward determining the form of the titanium-rich portion of the phase diagram up to 10 wt pct Be. MATERIALS AND METHODS Titanium sponge and a master alloy containing 25 wt pct Be were used in the formulation of the alloys; the chemistry of these materials is detailed in Table I. The alloys were prepared as 250-g compacts which were melted into buttons by arc melting under purified argon on a water-cooled copper hearth. Results of analyses for beryllium are shown in Table I but no determination of other elements was made at this stage. The alloys were hot-rolled at 1650°F to produce 0.1-in.-thick sheet. Alloys containing up to 1.5 pct Be were fabricated without trouble; samples containing 2 pct cracked initially upon hot rolling, but thereafter rolled satisfactorily to sheet. The 5, 7.5, and 10 pct were hot short and could not be rolled. Surface contamination was removed from samples by sandblasting and pickling in a 5 pct HF-35 pct HNOs solution. For metal log raphic examination, heat-treated specimens were mounted transverse to the rolling direction, ground on silicon carbide papers of increasing fineness to 600 grit, and electropolished at 20 v using a solution containing 600 ml of methanol, 60 ml of perchloric acid, 360 ml of butyl cellosolve, and 2 ml of Solvent "X". Difficulty was experienced in obtaining good electropolished surfaces with samples containing more than 1 pct Be, the degree of difficulty in-

Jan 1, 1967

By Herbert Dlaska

The BBU - rotary hearth treats lead concentrates and battery scrap by the roast-reaction process. It corresponds in principle to the long-known Newnam hearth, however its hearth-basin is not straight but curved to a closed ring. In operation this annular hearth is filled with liquid lead and rotates around a central blast-box. The charge, heated to a glowing-red, floats on top of the lead bath, into which air is blown from the blast-box through a horizontal slot-type tuyere. Ore pellets and brown coal are continuously charged onto the reacting mass from two storage bins. Lead is set free by the roasting reactions and trickles through the charge into the lead bath from where it is tapped from time to time. The reacting mass is continuously stirred by a mechanical agitator and backed, by a mechanical shovel, against the water-jacketed wall of the blast-box. The gangue of the charge forms lumps of scorified character, the so-called hearth slag or grey slag, which are discharged from the hearth. The waste gases are collected in a hood and conducted to a baghouse from where the fumes and dust are automatically transported to the pelletizing installation and are recycled with new material. The daily output of lead bullion depends mainly on the lead content of the charge. With lead concentrates containing 74% lead, about 24 tons of lead bullion per day are produced on the hearth at a direct lead recovery of about 89 per cent. Approximately 10 per cent of the lead content of the new material passes into the hearth slag from where it can be recovered in a blast furnace or in a rotary furnace. For small lead smelters the BBU-process represents the most economical way of melting high-grade lead concentrates. The process requires a relatively small capital investment, consumes little fuel, utilizes cheap fuel and is very flexible. Further, of great importance, is the fact that battery scrap can be treated by the BBU-process with very good results.

Jan 1, 1970

By C. P. Proctor, J. T. Crawford

TROUGH washers were among the earliest methods used for concentrating ores; they are referred to by Agricola about the middle of the sixteenth century as already being used while the hand- operated jigging sieve had only recently come into use. For cleaning coal the trough washer apparently was first used in France and Belgium .about 1841. The early trough washers were intermittent and the refuse at least was shoveled out by hand. The invention of a continuous jig washer, by a Frenchman, Berard, in 1848, acted as a stimulus to coal washings in jigs and retarded progress in trough washing' in the nineteenth century. Chapman and Mott describe a number of trough washers developed in England and on the Continent from 1850 to 1900, such as the Bell and Ramsay, Ramsay, Bell and Green, Wunderlich, Scaife, McLellan; Lodge, Elliott, Blackett, and Murton. , The later of these removed the refuse mechanically, either intermittently or continuously, but in ways that interfered with stratification. THE RHEOLAVEUR A Belgian engineer, Antoine France, is responsible for the development of means to remove refuse materials continuously from a trough washer while preserving stratification and preventing the loss of coal with the refuse. The methods and equipment devised, which have become known throughout the world as Rheolaveur, were initiated at the St. Nicholas mine near Liége, Belgium, about 1912. This installation consisted of two units to wash 20 to 8-mm. (13/15 to 5/16 in.) and 8-mm. to 0 (5/16-in. to 0), each having only two superimposed inclined troughs. The first few "Rheo" boxes on the top trough removed refuse directly and the remaining Rheo boxes discharged impure refuse to the lower trough for rewashing. On the lower trough the first few boxes removed refuse and the following boxes removed a middling product

Jan 1, 1943

By I. R. Kramer, P. D. Gorsuch, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By P. D. Gorsuch, I. R. Kramer, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By H. E. Stauss, J. Hino

INTEREST in silicon has arisen again in the past decade as a result of improvements in crystal rectifiers.' Although the preparation of silicon was first reported by Berzelius in 1880, the early product was of relatively low purity, and only the need for rectifiers in World War II led to the production of a 99.9+ pct pure powder. This material in crystalline form was consolidated into massive silicon for use, and the method developed was to melt it with selected added constituents as "doping" agents. Melting techniques, therefore, are of great importance. There are two basic problems in producing silicon ingots free of doping additions; one is the prevention of spitting and the other is prevention of cracking of the ingot during freezing. The most satisfactory arrangement yet developed for producing massive silicon is to melt and freeze in a cylindrical quartz crucible surrounded by a concentric heating element and concentric radiation shields or insulation. For example, use can be made of a tubular heater with a high frequency generator as the source of power and reflecting shields of alundum cylinders. The spitting of silicon is related to gas evolution, and the gas comes from two primary causes—adsorbed gas and the reaction products of silicon and the crucible. Gas is also released from bubbles contained in the quartz crucible walls. Improved removal of adsorbed gas can be achieved by means of controlled melting and freezing. The seriousness of the problem in vacuo is reduced with an electrically operated mechanical movement of the high frequency power coil. The upper portion of the powder charge is melted first and the high frequency coil lowered until the powder is completely molten. During cooling the high frequency coil is raised slowly. These means also reduce the final nonviolent extrusion of large beads of metal through the ingot top during freezing. Better control of spitting and bead extrusion is obtained when melting is done under helium at. atmospheric pressure instead of in vacuo. The problem of reaction between silicon charge and crucible in practice is confined to the reaction between silicon and quartz. This2 apparently is: Si + SiO2 + 2SiO The part that this reaction plays in spitting has not been isolated for separate study. SiO is a volatile vapor at the melting point; of silicon and is released freely during melting in vacuo, but hardly at all in helium at atmospheric pressure. The cracking of ingots is a major difficulty in melting silicon, and its prevention requires special melting techniques or the addition of "toughening" agents such as aluminum or beryllium.' The cracking of the ingots has been explained as being the result of the expansion that occurs upon freezing; although direct observation of freezing ingots reveals visible cracks on the surface only after a red heat has been reached, suggesting that cracking is the result of differential contraction of silicon and quartz. Silicon wets quartz, and the ingot adheres tightly to the crucible. Therefore as ingot and crucible cool, the two either have to pull apart, or at least one must crack. Surprisingly, in spite of the relative thinness of the quartz and the thickness of the ingot, the ingot and the crucible both crack. Microscopic and X-ray4 studies fail to show any plastic flow other than twinning in the ingots. Slow cooling fails to prevent cracking. Another possible solution to cracking is to weaken the crucible. Use of thin-walled crucibles finally led to success with fused quartz crucibles with a wall thickness of 0.25 to 0.50 mm. With such thin-walled fused quartz crucibles consistently uniform success is secured in producing sound ingots 30 mm in diam from the purest available grade of silicon (99.9+) without the use of any type of addition. Melts are made in the size range of 50 to 100 g. Omission of a deliberately added doping agent is not sufficient to insure pure ingots. The reaction of silicon with crucibles and the resultant solution of impurities in the silicon is well-established." In this laboratory, the presence of Al, Be, and Zr has been found spectroscopically in ingots melted in contact with alumina, beryllia, and zircon. The best crucible materials reported in the literature are MgO and SiO2. Use of MgO in this laboratory has resulted in a heavy deposit of magnesium on the furnace walls, showing that a reduction of the magnesia occurred and the resulting magnesium removed from the melt by volatilization. In the case of quartz, the silica is reduced and SiO liberated to deposit on the equipment walls. There probably is real danger that oxygen is dissolved in the ingot when either magnesia or silica is used as the crucible material. Preliminary analyses by Dean Walter in his vacuum unit in this laboratory6 indicate the presence of oxygen in undoped silicon melted in quartz.

Jan 1, 1953

By William Priestley

IN THE manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and elastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungsten, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured-by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. DESIGN OF GUN FORGINGS In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun are made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The elastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge.

Jan 12, 1921

By Walter F. Bradley

CLOSE to 300 members and guests were registered at the Regional Meeting of the Institute in San Francisco. Oct. 3-6, and many other mining men were present at some of the sessions, but failed to register. Headquarters were at the Palace Hotel. Technical papers for the Metals Session were sponsored by the San Francisco Section, whereas the program for the Industrial Minerals Session was arranged by the Southern California Section. Walter W. Bradley, Chairman of the San Francisco Section, opened the General and Metals Session, introducing President Buehler, who gave a hearty welcome to those present. Clyde M. Eye, of the. Benguet Consolidated Mining Co., presented the first paper, entitled "The Economic and Strategic Value of Philippine Metals to the United States." In closing, he urged. that this country retain and control the Philippines because their large

Jan 1, 1935

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development. The Indian Creek area is in the center of the northern half of Washington County, 11 miles northwest of Potosi, Mo., the county seat. The location is readily accessible from Potosi by car or truck over the all-weather Missouri State Highway No. 114. The topography is one of rolling relief, varying from an elevation of 700 ft above sea level on Mineral Fork and Indian Creek to a maximum of 1176 ft at High Point Tower. It is divided in equal halves between the drainage to Mineral Fork and to Indian Creek. The shaft site at 1060 elevation is on the divide between the two drainage areas. The Indian Creek side is rough and heavily wooded, with only a few cultivated clearings. The slopes to Mineral Fork are more gentle and rounded, with much of the area cleared for farm land. Most of the surface is covered with Potosi and Eminence formations, which show little evidence of any structure. Ore structure was worked out by extensive diamond core drilling, with holes varying in depth from about 700 to 1300 ft. As of Oct. 1, 1950, 218 prospect holes had been drilled within the 36-square mile area. The ore is disseminated galena with considerable accompanying sphalerite in the Bonne Terre forma-tion in the shape of irregular blanket-type deposits. The main controlling structural feature of the outlined mineral zone is a buried pre-Cambrian rhy-olite-porphyry ridge extending partly through the Bonne Terre formation, which laps against the por phyry and also covers it. The mineralized zone parallels and forms an irregular halo around the porphyry ridge and is concentrated in the Bonne Terre formation where the La Motte sandstone is cut out by the porphyry ridge. This is a very common mineral occurrence in the southeastern Missouri lead belt district. The La Motte sandstone, which normally underlies the Bonne Terre formation, is thus cut out entirely. In this area the Bonne Terre is usually about 275 to 320 ft thick, the La Motte varying in thickness from zero up to 400 ft. Commercial concentrations of ore are indicated at several places, the most notable being at the shaft site where an orebody at least 4000 ft long with widths of 500 to 600 ft has been outlined. The total thickness of mineralized rock reaches 150 ft in some holes, although total ore thickness runs from 8 ft to about 60 ft, often in more than one layer. Preliminary Planning Ore reserves as outlined lend themselves to open-stope mining with trackless haulage and mobile loading machines and drilling equipment. This type of equipment has proved to be very efficient during recent years in the company's lead belt operations. After a study of bids for shaft sinking and an estimation of comparative costs, it was decided that the shaft would be sunk by St. Joseph Lead Co. personnel using company equipment. Since the plant site is about 26 miles from the company's nearest lead belt operations, it was necessary to plan a complete surface plant, including mill, shops, office, change room, and warehousing facilities. Immediately following the filing of an application for a certificate of necessity, a headframe was selected for which detailed drawings were already available. The order was placed for fabrication so that it could be delivered and erected in time to serve for sinking the shaft. This eliminated the expense of a temporary headframe. Drilling was started on two churn drill holes near shaft location, and two 1000-gpm deep well pumps

Jan 1, 1954

L50 Adirondack L1 Alaska L2 Arizona L58 Arkansas L66 Billings Petroleum L3 Black Hills L4 Boston L5 Carlsbad Potash L6 Central Appalachian L60 Central New Mexico L7 Chicago L8 Cleveland L9 Colorado L57 Colorado Plateau L10 Columbia LII Connecticut L55 Dallas L12 Delta L65 Denver Petroleum L13 Detroit L14 East Texas L15 El Paso Metals L71 Evangeline L45 Florida L54 Fort Worth L16 Gulf Coast L61 Hobbs L62 Hugoton L68 Illinois Pet Basin L17 Kansas L18 Lehigh Valley L52 Lou-Ark L47 Mexico L19 Mid-Continent L20 Minnesota L56 Mississippi L21 Montana L22 Nevada L64 Niagara Frontier L23 New York L67 New York Petroleum L25 North Pacific L24 North Texas L26 Ohio Valley L27 Oklahoma City L28 Oregon L63 Panhandle L29 Penn -Anthracite L30 Permian Basin L51 Peru L31 Philadelphia L32 Pittsburgh L33 St Louis L34 San Francisco L59 San Joaquin L35 Southeast L36 Southern Calif L69 Southern Calif Pet L53 South Plains L37 Southwest Texas L48 Southwest Alaska L38 Southwest N Mex L44 Spindletop L39 Tri-State L40 Upper Peninsula L41 Utah L70 Venezuela L42 Washington, D C L43 Wyoming L49 West Central Texas L46 Philippine

Jan 1, 1956

By Gerard Matthes

Only in recent years has any practical headway been made in the application of aerial photography to geological problems, and up to the present time its principal value to the geologist and mining engineer has been in "areal geology;" i. e., the study of formations as revealed at the surface. The object of this paper is to set forth briefly the principal advantages that may be derived from aerial photographic data in geological work and to serve in a measure as a guide to those who may be contemplating its use. Geophysical prospecting has for object the locating of mineral under the surface. Inasmuch as the geologist's chief complaint in life is a dual one—inability to see under the surface and inability to visualize comprehensively what he does see on top of the ground—geophysical prospecting coupled with aerial photography should do much to lessen his burdens. To what extent aerial photography can be made a useful adjunct to geophysical prospecting remains to be proved, but the inference drawn here is that it holds many alluring possibilities. To avoid disappointments, it should be stated at the outset that to the geologist or mining engineer an aerial photograph or mosaic is only a tool, the efficient use of which he must set out to master. Upon his skill and ingenuity in applying it to particular problems will depend largely the value of the results that he will obtain. Under the most favorable conditions an aerial mosaic, or even a few loose photographs, because of the exceptionally comprehensive oversight which they afford of field data, such as dips and strike observations at isolated outcrops, local indications of faulting, mineral and fossil finds, greatly facilitate study and correlation, save much tedious foot work, and may repay their cost many times. Even so, types of country may be found where the most skillful use of the best of pictures will produce results so meager as to render the cost of aerial photography entirely unwarranted. Between these two extremes will be found endless variations and possibilities. Hence no set rules can be promulgated. The safest procedure is to treat each case as a separate problem and to carefully weigh the relative advantages and shortcomings of aerial photography before embarking on its use.

Jan 1, 1928

By J. R. Spencer

When supplies of high pressure mercury or other liquids are required in analytical work, it is convenient to have the source of supply at a relatively constant pressure and available in sufficient volume to satisfy the requirements of the apparatus in use. It is also desirable that the pressuring device be as simple and as inexpensive as possible and convenient to operate. This pump combined with a small storage reservoir containing gas under pressure has the attributes of (1) positive control of the maximum output pressure through the use of a regulator in the low pressure air supply; (2) an increasing capacity as the rate of withdrawal of mercury from the pressured system is increased; and (3) simplicity, requiring only the use of a lathe, drill press, and welding unit in its construction. DESCRIPTION Essential parts of the pump are shown in Fig. 1. In appearance the unlt is similar to the usual steam pump in common use in industrial applications although considerably smaller in size. The main differences lie in the area ratio of the air and mercury pistons and in the design of the air valve mechanism. Approximate diameters of these pistons are 4.25 in. to 0.375 in. respectively, giving an area ratio of about 130 to 1. The air piston (2) is attached to the end of shaft (4), with the mercury piston being merely a reduced extension of the shaft. Mercury intake and discharge to the pump are controlled by high pressure check valves that screw into the ports indicated at (6). Air supply is controlled by the valve assembly mounted on top of the

Jan 1, 1950

By Victor Lenher

The interest shown recently in selenium and tellurium has brought many requests for an assembling of the analytical chemistry of these two elements. The intention of this paper is to discuss all of the chemical principles utilized in the detection and quantitative determination of these elements, as well as to describe the works methods actually followed by producers of tellurium and selenium in the United States. These methods have been furnished by S. Skowronski of the Raritan Copper Works, H. D. Greenwood of the United States Metals Refining Co., F. F. Colcord of the U. S. S. Lead Refinery, and E. W. Rouse and A. E. Hall of the American Smelting and Refining Company. Occurrence Selenium is found associated with sulfur, to which in many respects it is quite similar. Occasionally deposits of native sulfur, notably those in the Lipari Islands, Kilauea, and Japan, show a red-brown coloration, I which is readily distinguished from that of other sulfur; this red-brown * sulfur contains a small amount of selenium. Not infrequently, the , sulfides of the heavy metals are accompanied by selenium and tellurium, • presumably as selenides and tellurides. The Scandinavian pyrite, which is one of the large sources of European sulfuric acid, when roasted has fur- - nished a large part of the selenium that has come to the United States; it I was in flue dust from the roasting of Scandinavian pyrites that the element was discovered by Berzelius in 1817. Greek and Spanish pyrites also

Jan 1, 1923

By Victor Lenher

The interest shown recently in selenium and tellurium has brought many requests for an assembling of the analytical chemistry of these two elements. The intention of this paper is to discuss all of the chemical principles utilized in the detection and quantitative determination of these elements, as well as to describe the works methods actually followed by producers of tellurium and selenium in the United States. These methods have been furnished by S. Skowronski of the Raritan Copper Works, H. D. Greenwood of the United States Metals Refining Co., F. F. Colcord of the U. S. S. Lead Refinery, and E. W. Rouse and A. E. Hall of the American Smelting and Refining Company. Occurrence Selenium is found associated with sulfur, to which in many respects it is quite similar. Occasionally deposits of native sulfur, notably those in the Lipari Islands, Kilauea, and Japan, show a red-brown coloration, I which is readily distinguished from that of other sulfur; this red-brown * sulfur contains a small amount of selenium. Not infrequently, the , sulfides of the heavy metals are accompanied by selenium and tellurium, • presumably as selenides and tellurides. The Scandinavian pyrite, which is one of the large sources of European sulfuric acid, when roasted has fur- - nished a large part of the selenium that has come to the United States; it I was in flue dust from the roasting of Scandinavian pyrites that the element was discovered by Berzelius in 1817. Greek and Spanish pyrites also

Jan 1, 1923

By Sixten Wollmar

A RESUME. of some important points regarding the life of drill steel, which have so far been learned from investigations carried out in the SKF Hofors' mines, Sweden, by L. Nordenfelt, is given below. By examining all fatigue breakages which occurred in the test it has bees conclusively proved that when a rock drill of the self-rotating type is used all break-ages of this kind start from the surface of the hole in the steel. It has further been proved that the rough hole surfaces (i.e., the marks left by the indentations of the sand core), are the starting points for the fatigue cracks and that the corrosive action of the water has .a very detrimental influence on the life of the steel. It is now a well known fact that this corrosive action concentrates at the bottom of the indentations left by the sand. The corrosive action of water has been well described by U. R. Evans in his paper, "Some Recent Work on the Corrosion of Metals," delivered on March 31, 1926, before the Liverpool Engineering Society, which is quoted in part below: "It is well known that, under ordinary conditions, most metals do not corrode in water unless dissolved oxygen is present. The strange feature of corrosion in submerged metals, however, is that the attack does not proceed mainly over those portions of the surface which could be reached readily by oxygen; deterioration takes place at certain points which are relatively, inaccessible to oxygen. When. a metal becomes pitted by corrosion, further attack usually deepens the pits, and in many cases it could be proved that there was no free oxygen at the bottom of the pits. None of the older theories of corrosion explain the fact that, although oxygen is necessary for rapid corrosion to take place, the attack actually occurs at the very points which could not be reached directly by oxygen.

Jan 6, 1928

By R. W. Waterfill

MANY existing ore deposits of valuable metals have been worked out in their upper surface levels and the continued productivity of these mines is dependent on their extension to greater depths in the earth. The maximum depths at present reached are about 6000 to 8000 ft. below the surface, with no evidence of an impoverished ore vein. These mines are widely distributed; some of the best known are in South Africa, Brazil, India and in the western sections of the United States. Among the factors which increase the difficulty of working these mines at increasing depths are hoisting, rock pressure and temperature. The manner and effectiveness with which these problems are met will, no doubt, determine in a large measure the ultimate depths to which any mine can be profitably worked. The most critical of these three factors at present is the increase in temperature with depth. The high temperature and humidity in many of these mines at present is severely detrimental to the health of the workers and greatly hampers their efficiency. Some have almost reached a condition in which the human system cannot survive. The problems involved in the cooling and ventilation of mines have all been ably analyzed and presented in previous articles. For this reason, only a resume of conditions affecting the cooling and conditioning of deep and hot mines will be given in this paper before attention is directed to possible methods of improving atmospheric conditions in the working levels.

Jan 1, 1929

By Wayne P. Myers

Electricity, as normally thought of by a layman's definition, is a manmade force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man's safety, are rigidly enforced by the U.S. Bureau of Mines, as well as the various state departments of mines. BACKGROUND Until recent years most underground coal mines used direct current exclusively for all movable and for some stationary equipment. Exceptions were for permanent pumps, tipple, fan, and outside buildings where alternating current was normally employed. However, over 60 years ago there were mines with dual systems. Alternating current was used for cutting machines, drills, and pumps, direct current for locomotives. There were no other machines as these were hand-loading mines. Later, during early mechanization in the 1920s, alternating current was also applied to loading machines at some mines. Use of dual electric systems then declined until fairly recently when

Jan 1, 1973

By Edward C. Mack, Ronald G. Stovash

INTRODUCTION Ronald G. Stovash General Superintendent Consolidation Coal Company Shoemaker Mine Moundsville, West Virginia Consolidation Coal Company's Shoemaker Mine is located in West Virginia's Northern panhandle near Wheeling, adjacent to the Ohio River. Steam coal is mined from the Pittsburgh #8 seam which averages 65 in. in thickness. The 10 in. of draw rock directly above the coal is taken on advancement, but remains when longwalled. The top consists of up to 12 in. of lower quality coal, and immediately over that, up to 10 ft of multi layered shales, coal, and bone. The cover ranges from 300 to 800 ft of shales and limestone. Two longwalls operate in the mine. The first longwall started in April 1975 and is retreating its eighth panel. This wall was the first to use shield supports in the United States. The second longwall started in September 1979 and is currently retreating its first 7,000 ft panel.

Jan 1, 1981