Search Documents

By C. N. Reid

Slip-line studies on deformed chromium single cvystals showed the usual bcc behavior. At room temperatuve, cross slip was prevalent—slip was not confined to a given plane, but the slip direction was (111). At -10O0K, slip occuvred on (110) planes, twins on(112) planes, and cleavage on (1001 planes. A single-crystal tensile specimen with an axis close to [011] showed a pronounced yield drop and high strain rate sensitivity which zclere used to derive relevant parame tevs in a dislocation dynamics treatment. Transmission electron microscope studies confirmed the existence of (110) slip planes and showed ecidence of loops punched out by precipitates and of grown-in dislocations promoting tangling. OF recent years experimental studies have been made of the deformation characteristics of single-crystal molybdenum and tungsten, but very little has been published on the behavior of single-crystal chromium. During a study of the mechanical properties of chromium, single-crystal studies were made which have already been partially described.&apos; However, additional information was generated which was not directly relevant to the main theme of Ref. 1, and, therefore, was not reported. In view of the need for complete documentation of deformation modes, the experimental observations made on the deformation of single-crystal chromium are summarized here, together with an electron-microscope study of the associated dislocation structures. It was found that, in terms of the deformation modes, chromium is a conventional bcc metal, showing a very pronounced yield-point phenomenon. Further, it was found that the flow strength of these crystals is very sensitive to the strain rate. Finally, the crystals were observed to contain many unidentified precipitates, which often were associated with prismatic dislocation loops. EXPERIMENTAL METHODS Single crystals were grown from rods of wrought chromium by the method of zone annealing. Rods of "1/4in.-diam were supported vertically in an argon atmosphere while an induction coil was moved up the rod at 1 in. per hr. The power was adjusted to just below that required for melting, and the process produced single crystals in about 30 pct of the rods used. The orientations of the crystals, in general, lay near [011] and are summarized in Fig. 1. Before this treatment, the wrought material contained 35 pprn C, 68 ppm O, and 12 ppm N.* An analyzed single crystal *Usual metallic impurities found in iodide chromium are: Al, 5 ppm; Ca, A ppm; Cu, 2 ppm; Fe, 75 ppm; Yg, 0.5 ppm; Yn, < 3 ppm; Mo, < 3 ppm; Ni, 4 ppm; Si, < 20 ppm; Ti, < 1 ppm; V, 4 ppm; Zr, < 3 ppm. contained 10 pprn C, 79 ppm O, and 50 pprn N. Tension and compression specimens were shaped from the crystals by mechanical grinding, followed by the electrolytic removal of about 0.010 in. from the surface in a perchloric/acetic acid bath. All specimens had a gage length of 0.75 in., and tension specimens had a diameter of 0.100 in., while that of the compression samples was 0.200 in. Mechanical tests were carried out at a rate of 1.3 pct per min, and temperatures below 0°C were attained by means of a nitrogen cryostat similar to that of Wessel.2 EXPERIMENTAL RESULTS Modes of Deformation. In addition to the tensile properties of these crystals, which are described in Ref. 1, deformation markings on the surface were studied. Crystals A and F, Fig. 1, were deformed in tension at 300°K to 10 and 16 pct strain, respectively. The surfaces contained visible slip lines, about 1 C( apart, composed of both straight and wavy segments. They did not define a single plane, and so determination of the slip plane was not possible. However, the slip direction was deduced by comparing the axial orientations of the crystals before and after deformation. Fig. 2 is representative, and shows that the axis ro-

Jan 1, 1968

By Frank V. Hicks

THE following paper-in no sense a technical paper-is a summary of a safety campaign instituted by a coal-mining company to improve an unfortunate safety record. The experience should be suggestive equally to coal and metal-mining companies. With few precedents to follow in the beginning, the course was charted by trial and error. The endeavor, often disheartening, finally resulted in the capture of the most coveted safety trophy in the mining industry, "The Sentinels of Safety," awarded by the Hercules Powder Co. of Wilmington, Del., through the U. S. Bureau of Mines. The period described covers the 10-year interval, 1924 to 1933, the year 1933 being that for which the award was made. The coal company considered has produced annually for a number of years an average of 2,750,000 tons of coal, employing at various times from 1.800 to 3000 men. Prior to 1924, the

Jan 1, 1935

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By Edward Keller

THE present ruling principle in shop and factory, induced by conditions of. keen competition, is to do the greatest amount of work in the shortest time, or in other words, to secure the greatest output at least cost, a condition which generally necessitated the substitution of machinery for manual labor. The chemical laboratory in our industrial establishments has remained a factor of minor importance, and, for this, reason, not only has progress been permitted to lag, but the methods of analytical work have been carried on along individual traditional lines. Some works-laboratories are equipped with such conveniences as Gooch filters, suction-pumps, compressed air, shaking-machines, centrifugal machines, crushers, etc., yet there is much room for improvement, particularly in laboratories of metal smelting and refining plants, in which long series of filtrations and stirrings are performed singly by hand in a slow and laborious manner. There are also many other instances in which collective handling appears rational. As a rule the chemist wastes much time by such manual labor, which, in a modern establishment and under up-to-date management, could be more advantageously applied to useful chemical work; and such higher chemical work is gradually and surely becoming recognized as an essential extension of old-time methods of assaying. While it maybe said that in some laboratories, boys and not chemists do the manual labor, it should be borne in mind that all chemical work requires care and accuracy and in these respects boys are naturally a source of concern to the responsible chemist. Moreover, the cheapness of child-labor is largely offset by the increase in the expense-account of laboratory materials, caused chiefly by breakages resulting from care¬lessness. Having; been authorized by the Anaconda Copper Mining

Mar 1, 1905

By R. F. Miller

DUE to wartime secrecy restrictions a large part of the technical information developed by government and industrial laboratories was withheld from distribution. Much of this information has now been released or "declassified" and reports of technical work carried out during the war in allied and enemy countries are also becoming available. Information on the latter subject has been augmented by the work of the Technical Industrial Intelligence Corps of the U. S. Army. Through the Joint Chiefs of Staff, rep¬resentatives of this Corps co-operated with the British Combined Intelligence Observations Subcommittee, and some of the observations were made by combined personnel of both groups. The U. S. Government has undertaken the indexing and abstracting of all of this information in the Bibliography of Scientific and Industrial Reports, a weekly bulletin which appeared first early in 1946. Other publications, such as the Bulletin of the British Iron and Steel Institute and The Metals Review of the American Society for Metals, provide abstracts of domestic and foreign magazine articles and papers presented to technical societies. However, they do not cover the industrial and government reports recently released by the Government nor the reports of the Army investigators hence the new bibliography is a welcome addition to our metallurgical library.

Jan 1, 1947

(Separates of all the Pamphlets published within the last three years (starting with No. 1469) are available, with few exceptions, at Institute headquarters. Separates of all the Technical Publications are also available. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute.] METAL MINING TRANS. PAMPHLET VOLUME NUMBER TITLE AUTHOR MEETING AND PAGE&apos;S 1033 Relation of Air Pressure to Drilling H. W. Seamon New York 66, 743, 756 Speeds of Hammer Drills Feb., 1921 1034 Time Factor in Depletion of Mines J. W. Roberts New York 66,711 Feb., 1921 1035 Calculation of Ore Tonnage and Grade J. E. Harding New York 66, 117, 122 from Drill-hole Samples Feb., 1921 1038 Discussion of Papers Presented in 1920 1041 Run-off and Mine Drainage H. N. Eavenson New York 66, 624,630 Feb., 1921 1043 The Health of the Underground Worker A. J. Lanza New York Feb., 1021 1045 Dust-ventilation Studies in Metal D. Harrington New York 66, 272, 289Mines Feb., 1921 1046 Discussion of Papers Presented at New York Meeting, 1021 1072 Breakage and Heat Treatment of Rock- B. F. Tillson New York 66,1758 drill Steel Feb., 1921 1073 Discussion of Papers Presented at New York Meeting, 1921 1076-M Analysis of Some Drill-steel Testa F. B. Foley New York 66, 789 Feb., 1921 1077-M Application of Magnetic. Analysis to C. W. Burrows New York 66, 796 Rock Drills Feb. 1921 1078-M Heat Treatment of Rock-drill Steel G.H. Gilman New York 66, 779_ Feb., 1921 1080 What is the Ideal Drill Steel? F. H. Kingdon New York 66,807 Feb., 1921 1051 Rock Drill Steels, etc. - W. T. Ober New York 66,814 Feb., 1921 1082-C Underground Mine Development, Its J. B. Dilworth Wilkes-Barre 66,715, 7.21 Definition and Valuation Sept., 1921 1084 Drill Steel from Hollow Ingots P. A. E. Armstrong New York, 66, 809 Feb., 1921 1088 Authors&apos; Replies to Recent Discussion 1092 Heat Treatment of Rock Drill Steel A. E. Perkins New York 66,811 Feb., 1921 1096-M Octagonal Ventilation Shaft. of Davis- J. L. Bruce Wilkes-Barre 66, 252, 268 Daly Copper Co. Sept., 1921 1100-C Determination of Electrical Equip- G. Bright Wilkes-Barre 66, 580, 605 ment for a Mine Hoist Sept. 1921

Jan 1, 1927

By A. S. Nowick, E. S. Machlin

ONE of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.1 During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time required for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error.2~3 This method of showing stress-rupture data has been adopted by many investigators and the KACA.4 By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, 100, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time for rupture on stress, temperature, com- position, and structure. In order to obtain this information, an investigation was made at the KACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given com- position and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efficiency and power output of gas turbines used in aircraft propulsion can be increased. THEORY The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 eveloped by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate- process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process.&apos;&apos; For example, in a chemical reaction the unit process is

Jan 1, 1947

By Chester Fulton

IN Polk County, Florida, the mining of raw phosphates began some 50 years ago with dredging operations on the Peace River, and in other near-by places by removal of shallow overburden with negroes and wheelbarrows, or with mules and scrapers, and the excavation and screen-ing of deposits found close to the surface. There were many individual operations of comparatively short life. Later steam shovels removed the overburden, and still later hydraulic methods were substituted for the steam shovel. Within the last 10 years large electrically operated drag-lines have almost entirely replaced hydraulic mining for overburden removal. The matrix is still mined by hydraulic giants and pumped to the washer or recovery plant. The many small operations have long since disappeared and the most desirable phosphate lands have gradually been acquired through purchase or merger by the seven companies that are operating in the field today. These companies are producing and selling about 2,000,000 long tons of phosphate per annum, or about two-thirds of what the industry likes to think is the normal output, with 1929 and 1930 in mind. To produce these 2,000,000 long tons of raw phosphate, they mine and treat about 1,000,000 tons of tailings from older and less efficient opera-tions, about 11,000,000 tons of matrix, and remove from above this matrix some 22,000,000 tons of overburden. The mining practice that has made possible the excavation and handling of 34 million tons of material to win but 2 million tons of merchantable product, selling for probably an average of only $4 per long ton when dried, should be of interest to the mining profession, though little has been written of it. The Florida Pebble Field, as it has come to be known, comprises an area (Fig. 1) within a radius of about 18 to 20 miles centering around Mulberry in Polk County, a small town 30 miles east of Tampa, Florida&apos;s largest port on the gulf coast.

Jan 1, 1936

By H. M. Kraner, R. C. Devries, K. H. Gee, E. F. Osborn

On the basis of liquidus measurements in the system COO-Mg0-Al2O3-Sio, and previously published data, diagrams have been constructed at 5 pct Al2O3, intervals from 5 to 35 pct Al2O3,. Liquidus temperatures and primary phase fields are shown. The optimum composition of a blast furnace slag for a given alumina content is indicated. At the optimum point, ordinary slags will be entirely liquid and will have maximum desulphurization potential and minimum viscosity. The relation of optimum composition of slags to the "plateau region" of the liquidus surface, and the application of these data on synthetic quaternary slags to actual slag compositions are discussed. Index of refraction of glasses is given as well as composition, temperature, and phase data for each mixture. THE usual blast furnace slag, as a first approximation, can be considered a mixture of the four oxides, CaO, MgO, Also,, and SiO,. Systematic, extensive data for the quaternary system, CaO-MgO-A1,0,-SiO, is therefore required for the understanding of the properties of such a slag as a function of composition and temperature. With sufficient data, it should be possible to fix unequivocably the relative amounts of lime, magnesia, and silica required for a given alumina content to result in a slag composition having optimum properties. Other constituents, such as FeO, MnO, Ti02, and S, have an effect on the properties of a slag, but as long as they are present in small and approximately constant amounts they produce only a second-order effect superimposed upon the major changes in properties of slags determined by the relative amounts of the four major components. Viscosity and desulphurization data have been reported for mixtures approaching blast furnace slags in composition, but systematic liquidus data have not been obtained. Inasmuch as a slag must be all liquid in order to be most effective as well as practicable, clearly the temperature above which a mixture is all liquid (liquidus temperature) is a type of data needed. Such data have been obtained through the study of 446 compositions and are pre- sented in this paper along with a discussion of their bearing on the optimum composition of blast furnace slags. For an orderly presentation of the data, the quaternary system is viewed as a tetrahedron with one component at each apex. Fig. 1 shows a tetrahedron representing the system Ca0-Mg0-A1,0,-Si0,. The base is the ternary system Ca0-Mg0-SiO,, A1,0, is the top apex, and the front face, the system CaO-

Jan 1, 1955

By Winston W. Spencer

ALTHOUGH by far the largest A consumer of platinum metals in the world, the United States until recently has been in- significant as a producer. Writing in the "Minerals Yearbook" for 1939, H. W. Davis states that 1938 probably marked the beginning of an- other period of transition in the world production of the platinum metals. In that year, he says, their production in the United States jumped to 49,380 oz., or fourth in the rank of world output. In the ten-year period 1925 to 1934 United States output ,averaged only 8300 oz. Practically all of this sudden in- crease in production is attributable to the introduction of mechanized equipment at the placer deposits in the Goodnews Bay district of Alaska. This district adjoins the Bering Sea and Kuskokwim Bay (accented on the first syllable), and is approximately 120 miles south of the mouth of the Kuskokwim River. The nearest village and post office is Platinum, which lies about eleven miles north- east of the Goodnews Bay Mining Company&apos;s camp. A good gravel road connects the mine camp and the village.

Jan 1, 1940

By G. O. Prickett, P. Somasundaran

An experimental progmm based on statistical principles is used for optimizing a flotation operation for the separation of minerals. In this case, flotation of sylvite from sylvinite ore with amine and starch as the flotation reagents was studied to find the optimum reagent levels at various slime levels. The experiments were first done on a two-level three-factor design. Analysis of the results showed that the interactions between various factors were significant. Hence, a first-order linear model of the flotation response would not be accurate. The two-level three-factor design was expanded into a composite design in order to test the fit of a higher-order model. Data were treated to obtain an expression for flotation response as a function of the different variables, to predict the optimum reaaent levels at various slime levels, and also to determine the path of steepest ascent. Tests around the predicted optimum and along the path of the steepest ascent were done until a near-optimum region was obtained. Exploration of the nature of the response surface in that region established the actual location of the maximum response. The optimum amine level was found to be 0.20 lb of amine per ten of ore at all slime levels, while the optimum starch level varied as a function of the slime present. Computer access at the laboratory by means of a teletype terminal on a commercial time-sharing system enabled efficient and accurate treatment of experimental data. The efficiency of experimental investigations can be improved significantly by the use of experimental design and data analysis based on statistical principles. The common approach used in experimental research is to study a property of a system as a function of "one-variable-at-a-time". Several authors&apos;-4 have pointed out the inadequacy and deceptiveness of this method. Results obtained for the effects of a variable on the measured response of the system using

Jan 1, 1970

By Alfred R. Powell

Late in 1944 a group of petroleum and coal technologists was organized in Washington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Tehnical oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. since oil-production facilities in Germany and the occupied countries controlled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Induslrial Intelligence Com,mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A summary of the more important information gained by this combined British and American mission is presented below. German Oil Production The oil available to Germany, both natural and synthetic, and including production from occupied countries, reached a peak in late 1943 and early 1944 Production at this time was at the rate of 1,200,000 metric tons Per month, equivalent to 100,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, jo per cent was crude oil from Romania and Hungary, 12 Per cent was crude oil from Germany itself, including Austria, 9 per cent cumprised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of wartime production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syrlthetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per Cent of the peak qualltity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1947

By Alfred R. Powell

Late in 1944 a group of petroleum and coal technologists was organized in Washington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Tehnical oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. since oil-production facilities in Germany and the occupied countries controlled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Induslrial Intelligence Com,mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A summary of the more important information gained by this combined British and American mission is presented below. German Oil Production The oil available to Germany, both natural and synthetic, and including production from occupied countries, reached a peak in late 1943 and early 1944 Production at this time was at the rate of 1,200,000 metric tons Per month, equivalent to 100,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, jo per cent was crude oil from Romania and Hungary, 12 Per cent was crude oil from Germany itself, including Austria, 9 per cent cumprised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of wartime production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syrlthetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per Cent of the peak qualltity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1947

By Michel David

One of the most important questions that arises in ore estimation can be stated as follows: What is the error when one extends the grade of a sample to a certain volume? The theory of regionalized variables, with the concept of extension variance, provides a response to that crucial question for any kind of sample extended to any volume. For the usual "extensions" encountered in current mining practice, some simple results can be derived from that theory which was initiated by Dr. G. Matheron. These results have been applied to a stratiform lead-zinc deposit for which several estimations of grade, tonnage and related precision have been made for a series of grid sizes such as might be used in a progressive exploration program.

Jan 1, 1969

By Ronald C. Whiting

SINCE the advent of what has been aptly called "chemical flotation," about 1920, the number and complexity of the various chemicals used in practice have increased enormously. Over 300 patents have been issued dealing exclusively with flotation reagents, and many of these embrace from two or three up to a score or more of specific compounds. The exact number of compounds actually finding a practical use in flotation would be difficult to determine, though the U. S. Bureau of Mines gives an annual list by groups.

Jan 1, 1938

Discussion of the paper of DOUGLAS BUNTING, presented at the New York meeting, February, 1915, and printed in Bulletin No. 97, January, 1915, pp. 1 to 21. ARTHUR HOVEY STORRS, Scranton, Pa.-I know something about accidents Nos. 4 and 8. At the Fuller mine there was no disturbance of the surface in connection with either of those accidents, there was no surface settling, nor signs of sand in the mine, and seemingly the water all came from a subterranean basin or water-bearing stratum overlying the Six Foot vein. A similar thing was shown, in an accident not referred to in Mr. Bunting&apos;s table, at the Avondale, where we had an inflow of water, as high as 12,000 gal. a minute, for a considerable period. Regarding the second accident (No. 8) at the Fuller mine: after the first inflow of water (No. 4 of the table), the mining was abandoned in the Six Foot vein. A long slope was. driven in an underlying seam, and when this had reached a point about 2,000 ft. southeast of the place where the first inflow of water occurred, and where the bore holes show there was apparently sufficient rock covering for the Six Foot vein, a rock plane was driven up to the upper vein (Six Foot) and one afternoon this exposed the coal. During the following night the inflow of the water occurred. There were absolutely no workings at this point so that no disturbance of the overlying rocks could have occurred. The result of the inflow of water was to fill up the entire lower-vein workings in about two or three clays and caused the abandonment of the mine. After several years, considerable time and money were spent in an effort to hoist the water from the shaft and mine workings, with varying, but in the main rather indifferent, success until, clue to the breaking of one hoisting rope, the engineer pulled the other hoisting tank up through the tower and down on to the engine, making a complete wreck of the whole plant. It was then decided to allow the mine to soak and it is still doing so, other portions of the property being mined from adjoining collieries.

Jan 5, 1915

By H. O. Hofman

INSTITUTE OF TECHNOLOGY, In deternlining experimentally the fusibility of clays, two kinds of methods may be distinguished—the direct and the indirect. Of the direct methods, that of Seger has found

Jan 1, 1899

By Walter Miller

NOW, after a year&apos;s continued impact of war, the task of the petroleum-refining industry stands out clearly and looms up in larger aspect. This time it is not, as it was so largely in the first World War, simply a matter of increased quantity- more and more of the same petroleum products that had substantially been standard for years. In this era the emphasis is largely on newer and improved materials which had been produced, if at all, in comparatively insignificant quantities, and for which manufacturing equipment was not available on a large scale. At the beginning of 1942 four great product needs (besides a number of lesser one-) confronted the industry: 100-octane aviation gasoline, toluene for T.N.T. production, high-quality lubricating oils for aviation and Army equipment service, and petroleum chemicals for synthetic rubber manufacture.

Jan 1, 1943

By George S. Rice

ARIAL maps of prospective mineral-bearing territory have become almost indispensable in all the branches of exploration, and have proved particularly useful in the great oil area of the Southwest. About nine years ago aerial photographic mapping in this area was begun. The early product was lacking in scale accuracy and other control features, which limited its effective use. Since then, the evolution of the technique of such mapping has been steady, with several mapping companies collaborating with five of the leading oil companies, and aerial maps have been prepared covering practically the entire area.Improvements in cameras, film, and developing equipment and practice have resulted in more uniform and clearer photographs, but the outstanding development has been the accuracy obtained with respect to scale and all other control features. Maps are no

Jan 1, 1936