Search Documents

By Mäkinen, Eero

OUTOKUMPU, a large copper mine in eastern Finland, has the distinction of being one of the few important mines in the world discovered by a geologist the late Otto Triistedt, of the Geological Sur- vey of Finland, having found the out- clop in 1910 by tracing glacial ore boulders, some of which had been carried as far as fifty kilometres. As the mine had no connection with either railways or waterways and the possibilities of transport were poor, the owners first tried the Hybinette hydrometallurgical process to extract the copper. The raw ore was finely crushed, treated by a sulphatizing roast. and then leached. The resulting solution was electrolyzed, using lead anodes. This experimental plant, having a capacity of 10,000 tons (all Ions are metric tons in this paper) of raw ore and producing 300 to LEO0 tons of electrolytic copper annually, was built in 1913 and run until dis-

Jan 1, 1938

By J. P. Witherow

The blast-filmace plant of the Crozer Steel and Iron Company was built under contract by Witherow & Gordon, of Pittsburgh, Pa. The furnace is 70 feet high by 16 feet bosh, tunnel-head 12 feet 8 inches, and hearth 9 feet in diameter. The columns are 20 feet high above furnace level, below which they extend 2 feet. The shell is 23 feet diameter at bottom and 19 feet at top. The plate iron is 3/8 inch at bottom, and tapers to 1/4 inch, the top ring being 5/16 inch.

Jan 1, 1884

By W. M. Bertholf

IN 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral can make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory," as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,1 but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1946

By T. J. Smolik, Harman, D. W. Fuerstenau

By means of electrokinetic measurements, the surface properties of the aluminosilicate polymorphs (sillimanite, andalusite, and kyanite) and also mullite have been found to depend on the ratio of A10 bonds to SiO bonds in the surface. The Al-toSi ratio in the surface is dependent upon the crystal lographic properties of the mineral, which in turn determine coordination numbers of A1 and of Si, cleavage characteristics, and density of the various solids. Mullite with a greater bulk Al-toSi ratio has the highest zpc of the aluminosilicates. By treatment in dilute acids or by cycling between acidic and basic solutions, alumina is selectively dissolved from the surface of these orthosilicates. This shifts the apparent zpc to lower pH values as the fraction of SiO groups in the surface increases. Thus, surface properties can be altered by procedures that alter the A l-to-Si ratio in the surface. Flotation of these aluminosilicates results from electrostatic interaction of the collector ions with the mineral surfaces. As a result, flotation response shifts in accord with any shift in apparent zpc by pretreatment. Separation of minerals by flotation is based on differences in the physicochemical properties of their surfaces.'-3 For many minerals, adsorption of flotation collectors results from their functioning as counter ions in the electrical double layer at solid-water interface. In such systems, separation depends on differences in the zero point of charge (zpc) of the various minerals. The zpc is defined as the concentration of potential determining ions in solution at which the surface is uncharged. The potential determining ions for inorganic oxide-water interfaces are hydrogen and hydroxyl.4,5 This work is concerned with the effects of crystal structure, composition, and surface preparation on the surface properties and flotation behavior of aluminosilicates. Differences resulting from crystal structure were studied by measuring electrokinetic potentials and determining the flotation behavior of three different aluminosilicate materials having the same chemical composition (Al2O3 SiO2), namely andalusite, kyanite, and sillimanite. Furthermore, the effect of the Al2O3-to-SiO2 ratio on flotation behavior and surface properties was investigated by including synthetic mullite, 3A12O3 .2SiO2. Gaudin and co-workers 6,7 have clearly shown how crystal structure determines the native floatability of certain minerals. Those solids in which the surface is comprised mainly of broken residual bonds possess naturally hydrophobic surfaces. It was found by Bakakin8 that for a number of oxidized lead minerals, differences in floatability were due to the distance of Pb atom from the surface. Only limited work has been done on relating electrical properties of surfaces to crystal structure and composition. Healy et. a1.9 found that the zero points of charge of various manganese dioxides ranged from about pH 1.5 to pH 7.5, and these differences in the zpc's were interpreted in terms of the atomic packing in the various crystals. The research presented here clearly shows that crystal structure and chemical composition do affect the surface properties of aluminosilicates and, in addition, that these effects can be altered by changing conditions under which the surfaces are prepared. CRYSTAL STRUCTURE OF THE ALUMINOSILICATES Sillimanite, andalusite, and kyanite are composed of regionally metamorphosed rocks differing mainly in degree of metamorphism. All three minerals have the same chemical composition, Al2O3 - SiO2, of which sillimanite is the high temperature polymorph and kyanite and andalusite the lower temperature polymorphs. Andalusite and sillimanite crystallize in the orthorhombic system while kyanite crystallizes in the triclinic system. The structure of these three minerals is essentially chains of aluminum-oxygen octahedra linked laterally by silicon and aluminum. The arrangement of these chains in the three minerals is shown in Fig. 1.l4

Jan 1, 1967

By R. P. Fischer

The Colorado Plateau region has been the principal domestic source of uranium, vanadium, and radium. The value of these commodities produced from the region through 1964 slightly exceeds $2 billion. Most of the deposits occur in streamlaid lenses of sandstone in the Chinle and Morrison Formations. The ore minerals below the zone of oxidation are low-valent oxides and silicates of uranium and vanadium; all of these, except the quite stable vanadium silicates, oxidize readily to a variety of high-valent uranium and vanadium minerals. The ore minerals partly replace fossil wood but mainly impregnate sandstone, typically forming tabular ore bodies that are nearly concordant to the bedding of the host rock. The deposits range in size from those containing only a few tons of ore to those containing more than 1 million tons. Stratigraphic, lithologic, and sedimentary structural factors obviously influenced the localization of these deposits, but igneous activity, hydrothermal mineralization, and tectonic structures show no similarly consistent influence on localization. The deposits are epigenetic, but the source of the ore metals, the nature of the ore-bearing solutions, and the time of ore emplacement are uncertain. A few uranium deposits in the region are dominantly discordant to bedding and occur in collapsed breccia pipes or along linear fractures. Their origins are also uncertain.

Jan 1, 1968

By Edward Hart

Having occasion several years since to make ferrous sulphide, I attempted to do so by fusing a mixture of coal-brasses (FeS2) and dried ferrous sulphate. A very nice-looking sulphide was obtained; but on attempting to use it, I found that it was insoluble in dilute hydrochloric and sulphuric acids. The subject was laid aside at the time, but has since been taken up; and some curious results have been obtained, which I believe are new. I have made the material by all of the following methods and the product seems to be pretty much the same, however obtained : (a) FeS2 heated to fusion. (b) FeS2, and FeSO4 heated to fusion. (c) FeS2, and Fe2O3 heated to fusion. (d) FeS2, and FeCO3, heated to fusion. (e) FeSO4, and S heated to fusion. (f) Fe2O3 and S heated to fusion. Obtained in this way the mass after cooling breaks easily and is very nearly black in color. On the upper surface of the fused cake the color is generally reddish or brownish black. When this is treated with dilute sulphuric or hydrochloric acid, it refuses to dissolve; but if touched with the point of a file or any piece of wrought-iron, solution of the sulphide takes place with the evolution of sulphuretted hydrogen. If the iron is removed the evolution of gas ceases, and only begins again when the iron is again brought into contact with the fused sulphide. The same thing happens if the iron is connected with the sulphide by means of a platinum wire. But in all the samples of fused sulphide I have obtained, if the iron is allowed to remain in contact with the sulphide for a certain time (which varies with different samples of the fused sulphide) and is then removed, solution of the sulphide continues. Zinc, tin, and magnesium have the same effect as iron. In hydrochloric acid aluminium acts more rapidly even than iron. In sulphuric acid it has little if any effect. Copper in HCl, when brought in contact with the fused sulphide, dissolves quietly without evolution of gas. The solution of copper chloride formed becomes,as it flows down over the sulphide, converted into copper sulphide.

Jan 1, 1887

By A. P. Cohen, D. W. Fuerstenau

Methods of accounting for the feed size in analyzing the size distribution shift during comminution have been discussed in a number of papers.1,2,3 Based on experiments which charles2 performed with single Pyrex specimens, Schuhmann4 pointed out that the size modulus of an assembly of particles should be determined by the energy expended per unit volume (or mass), independent of the size of particle being comminuted. In this same paper, Schuhmann derived the Charles energy-size reduction relationship by considering that complex comminution operations can be considered to be the summation of many individual comminution events, each of which must be governed by Were 6wi is the mass of a particle receiving the impact, 6Ei is the energy delivered to the particle, ki is the size modulus of the product resulting from the impact, a is the distribution modulus of the assembly of particles, and A is a constant. Recent experiments on the compression loading of Pyrex spheres ranging in size from 1/8 to l-in. diam have shown that the size modulus of the fragments is determined by the strain energy at fracture per unit mass, independent of sphere diameter.' The objective of the present investigation has been to determine experimentally whether the size distribution of the product from such a complex comminution process as rod milling is determined only by the energy expended per unit mass independent of feed size. Samples of each Tyler sieve fraction ranging from 4x6 to 48x65 mesh were prepared from crushed Brazilian quartz crystals. One kilogram of each fraction was ground at 60 pct solids in an 8x9 1/4-in. mill containing 17.5 kg of rods (26 rods, 5/8-in.; 10 rods, 3/4-in.; and 5 rods, 7/8-in. diam). In each test, the mill was run at 77 rpm for 15 min. Size distributions were determined by a wet-dry sieving technique. Table I presents the size distribution of the products obtained by grinding each of the size fractions. Because the size distributions are so nearly alike, they are plotted in Fig. 1 by shifting each size distribution for the different feed sizes one screen fraction to the right. Thus, the lowest point in each size distribution represents 400 mesh and each of the other sieve sizes must be shifted accordingly. A single regression line was calculated by combining the data for the six tests, excluding the coarsest feed and the two finest feed fractions. 6 This regression line, which is given by (Y \0.88 where y is the cumulative percentage of material

Jan 1, 1962

By B. I. Routh

A STUDY of the effects of temperature on the gel strength of drilling muds is a natural outgrowth of the present era of deep drilling. The control of the gel solids' is now considered important because it affects the wall-building qualities; the suspension of weighting material; the removal and release of sand, cuttings, and gas; and the control of cav-ing formations. With regard to the effect of temperature on gel strengths Herrick2 states: "Temperature variation within ordinary limits does not have much effect on yield points." Lewis, Squires and Thompson3 investi-gated one clay and found no marked change with temperature in either yield point or mobility. Reed4 found that potassium bentonite showed a great increase of gelation with increase in temperature and qualitatively there occurred a marked increase in viscosity upon heating. The apparatus used in these experiments consisted of a Stormer viscosimeter, Marsh funnel viscosimeter, rectangular and cylindrical shearometers, Mudwate hydrometer, and other minor laboratory equip-ment. The various methods of measuring viscosity and gel strength have been extensively described by Evans and Reid.5

Jan 1, 1938

By T. T. Field, M. Gell

MUCH has been learned about plastic deformation behavior in crystals through the use of dislocation and slip band etchants. Slip in nickel and nickel-base alloys has previously been revealed by various etching techniques.l-5 The techniques for nickel-base super-alloys4,5 were successful only in the Udimet 700 composition in specific heat-treated conditions. The objective of this work was to develop a more generally applicable slip-band etching procedure. The nominal compositions of the alloys used in this study are listed in Table I. The low carbon Mar-M2OO alloy referred to in the text is the same as listed in Table I with the exception that the carbon content is less than 100 ppm. Mar-M200 and Udimet 700 were solutionized at 2250" and 2150°F, respectively. The aging treatment for both cast alloys was 32 hr at 1600°F and for wrought Udimet 700 was 4 hr at 1975"F, 24 hr at 1550°F, and 16 hr at 1400°F. The new slip-band etching technique consists of a chemical etch followed by a short electropolish, Table 11. Fig. l(a) shows the best result obtained on an internal section of a plastically deformed single crystal of Mar-M2OO when using a conventional slip-band etching procedure which consists of electropolishing followed by etching. Ghostlike traces corresponding to planar slip bands are observed, but the contrast between the bands and the background is weak. Fig. l(b) shows the same field using the new slip-band etching technique. After the etching step of this technique, the same ghostlike traces of Fig. l(a) are observed, but the subsequent electropolishing accentuates the slip bands and the subgrain boundaries while the rest of the matrix is being polished. Longer electropolishing obliterates the slip bands. The new slip-band etching technique makes use of the etchants and electrolytes that are normally used for a given material. Because of this, it should be possible to slip-band etch other nickel-base superal-loys by using existing etchants and electrolytes for a material and following the procedures outlined in the "Comments" section of Table 11. All the illustrative examples given below show internal plastic deformation in single crystals of regular and low carbon Mar-M200 in the solutionized and

Jan 1, 1970

By F. Ernest Brackett

Much new data on the flow of gases have been discovered by recent experiments by the United States Bureau of Mines and others. Although additional investigation is still desirable, the information now collected seems sufficient to attempt a tentative coördination of the friction factors. This study is confined entirely to fluid friction when the density throughout the duct is so nearly constant that it may be so considered. In the subsequent discussion the following notation is used: v = mean velocity of fluid in duct, feet per second. v' = mean velocity of fluid in duct, meters per second. R = hydraulic radius of duct, feet. R' = hydraulic radius of duct, meters. S = the hydraulic slope. P = pressure absorbed by friction, pounds per square foot. p = pressure absorbed by friction, pounds per square inch. p' = pressure absorbed by friction, kilograms per square centimeter. A = sectional area of duct, square feet. O = perimeter of duct, feet. L = total length of duct, feet. L' = total length of duct, meters. d = diameter of a cylindrical duct, inches. w = density of the fluid, pounda per cubic foot. g = specific gravity of the fluid compared with water = w % 62.4. C, k and B, coefficients for formulas using English measures. C' = metric coefficient, v' = C'R'S. n = coefficient of roughness for English or metric units. The basic formula for the flow of all fluids at constant density appears in the three following forms, which may be denominated: (a) The slope formula, v = CRS (b) The ventilation formula, " n = (c) The pipe formula, C is Kutter's coefficient, which is extensively applied to the flow of water in ducts and channels of all kinds; E is Atkinson's coefficient, used principally with air in ventilation problems; B is a coefficient conveniently adapted to studying the flow of water, gases and vapors in pipes. 312

Jan 1, 1927

THE opening session was held on Tuesday evening, February 17th, in the house of the American Society of Civil Engineers. The President of the Institute, Mr. E. B. Coxe, after a few introductory remarks, congratulating the members on the general prosperity in all the branches of the professions and manufactures represented by the Institute, called on Mr. E. F. Loiseau, of Philadelphia, for the first paper, On the Successful Manufacture of Compressed Fuel at Port Richmond, Philadelphia. Professor Prime called attention to the fact that the work of the United States Testing Board had been left unfinished at a point when valuable results had just been reached, and offered the following resolutions: WHEREAS, The American Institute of Mining Engineers has seen with regret that the work of the United States Testing Board has been suspended through the lack of an appropriation by Congress, which appropriation dues not seem likely to be renewed, and WHEREAS, It seems most important to the vital interests of our iron and steel manufactures that the experiments commenced by the United States Testing Board should be carried to successful completion ; Resolved, That a committee of three be appointed, to act with a like, committee to he appointed by the American Society of Civil Engineers, to carry out to completion the work commenced by the United States Testing Board. Resolved, That the American Society of Civil Engineers be requested to cooperate with this society by the appointment of a like committee. Resolved, That the committee have authority to request, in the name of the American Institute of Mining Engineers, contributions to a fund to be devoted to the completion of the experiments aforesaid. Resolved, That the Council of this Institute be authorized, whenever requested by the committee so appointed, to petition Congress for the free use of the testing machine at the United States Arsenal at Watertown. Resolved, That a committee be appointed by the President, to select the afore-said committee of experts. Resolved, That the President of the Institute have authority to fill any vacancies which may occur in the committee. The resolutions were unanimously adopted, and President Coxe appointed the following committee in accordance with the resolutions : Messrs. A. L. Holley, James Park, Jr., and J. F. Holloway. The President also appointed Messrs. Heinrich, Mickley, and Spils-

Jan 1, 1880

By Bjorge, Guy N.

MINING method improve through the gradual process of evolution and in 1340 there were no marked outstanding innovations. On the other hand refinements of detail and betterment: in equipment design continued to progress. Among the most important changes have been the increased application of trucks and highway equipment, including tractors and bull- dozers, to open-pit mining as exemplified by Phelps Dodge's Morenci operations; the Mesabi iron range; and the Tri-State district. Mass or bulk handling contributed its part underground with slurhers and conveyors at Consolidated Coppermines and slushers at Climax; and in open-pit mining. conveyors found increased use on the Mesabi range.

Jan 1, 1941

By A. R. Kinkel

Robert T. Walker and Woodville J. Walker (Walker Engineering Corp., Salt Lake City)—Mr. Kinkel's article embodies, in condensed form, the results of the first detailed and complete geological survey that has ever been made of the long neglected but potentially very important West Shasta Copper-Zinc district, in Shasta County, California. In view of the difficulties of the terrain and the complexity of the geological structure, this represents a notable achievement, and it is with regret, therefore, that the writers find it necessary to differ from Mr. Kinkel's conclusions on two important points. The first has to do with the interpretation of two members of the stratigraphic column of formations in the district; for purposes of comparison, the description of these two members according to Mr. Kinkel is shown parallel to the description of these members according to the writers, see Fig. 14, Mr. Kinkel's nomenclature being used. The first member, which Mr. Kinkel terms the upper unit of the Balaklala rhyolite, consists of a single, massive, homogenous body of very silicious igneous rock, consisting almost wholly of quartz and albite, and averaging about 80 pct silica. Most geologists of the U. S. Geological Survey who have previously inspected the district have called it an alaskite. It is not a pile of several members, but is a single unit, without internal subdivisions. It has the form of a recumbent lens, approximately flat on the bottom and arched on top, several miles in diameter, and attaining a maximum thickness of 1000 to 1200 ft. It varies in texture from porphyritic to holocrystalline, and contains unusually large quartz phenocrysts up to 4 mm diam. Mr. Kinkel considers this formation to be a thick lava flow that is older than the overlying Kennett shale, while the writers interpret it as being intrusive, constituting a domed sill or laccolith that is younger than the Kennett shale. Their reasons are as follows: 1) This formation shows none of the features which within the writers' experience invariably accompany very silicious lava flows. Nowhere is it vesicular; nowhere does it contain any glass or its devitrified equivalent; nowhere does it contain flow breccia; and nowhere has it a ragged top, in spite of the fact that there is no evidence of surface erosion, which might have removed such a top.

Jan 1, 1957

By H. R. Ogden, A. G. Imgram, D. N. Williams

The effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. Increasing the chromium, vandium, or aluminum content increased the strength of quenched structures with chromium being the most effective strengthener. Appreciable aging response was obtained with low chromium alloys, but high chromium alloys age softened rather than. hardened. High vanadium contents had a similar effect. Aluminum additions shifted the aging behavior toward that observed in lower chromium alloys, enabling high chromium alloys to be age hardened. DURING the course of titanium alloy development many a and a-ß alloys have been evolved to commercial status. However, only one all-ß alloy has achieved this same stature. This is the Ti-13V-11Cr-3Al alloy. It is characterized by a very sluggish ß-phase decomposition reaction such that very slow cooling rates can retain the 0 phase at room temperature. In addition, very high strength levels can be obtained by long-time aging treatments. Combinations of cold or warm working followed by aging produce even further improvements in strength. This paper describes the results of a research program in which the effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. EXPERIMENTAL PROCEDURES Electrolytically refined, high-purity titanium was used as the alloy base for these studies. Iodide chromium, electrolytically refined vanadium granules, and high-purity aluminum sheet were used as alloying additions. The compositions of interest were melted as 250-g ingots in a direct current arc melting furnace under a flowing atmosphere of argon. The ingots were hot forged to 3/4-in.-diam bars, vacuum annealed for 6 hr at 1800°F to reduce residual hydrogen content, and then hot swaged to 1/4-in.-diam rods. Fabrication history, and interstitial analyses after fabrication are given in Table I. All specimens to be heat treated were sealed in Vycor capsules under a partial pressure of argon. Samples used to define the ß transus were quenched from temperatures ranging from 1350° to 1100°F after holding at temperature for 15 min. Samples for aging studies were quenched from above the ß transus temperature and then aged for up to 64 hr at 750°F and for 100 hr at 850°, 900°, and 950°F. The effects of straining prior to aging were also investigated. The results of these studies were used to select the heat treatments for the tensile specimen blanks. Heat treatments of the tensile specimens are described in Table 11. Alloys were aged after solution heat treatment or after solution heat treatment and cold swaging to 50 pct reduction in area. Standard 0.125-in.-diam tensile specimens were machined from the heat-treated blanks. All tensile tests were performed in a Baldwin-Southwark uni-

Jan 1, 1963

By J. Armanet

THREE MINING colleges are maintained in France; the École Nationale Supérieure des Mines, of Paris; École Nationale Supérieure des Mines, of Saint Etienne; and the École Supérieure de la Metallurgie et des Mines at Nancy. Besides graduates of these schools, a few graduates of the École Centrale des Arts et MIanufactures and of the École Polytechnique are employed as ]nine managers or engineers; however, most of the latter have taken a graduate course at one of the mining schools.

Jan 1, 1939

By Gordon MacVean

THE adoption of rock dusting, as a safety measure, has made notable progress in the West Virginia coal mines since May, 1925. At that time there were but two mines in the State that were thoroughly rock dusted, mines No. 2 and No. 12 of the Boone County Coal Corp., at Sharpless. Since then it is probable that 75 per cent of the coal operators in the State have given consideration at one time or another to rock dusting. This growth of interest followed the meetings of the various mining institutes all over the country, during the summer of 1925, at which papers were presented, drawing the attention of the coal mining operators to the merits of this safety measure. Yet outside of the experience with rock dusting at the Old Ben Coal Corp., of Southern Illinois, and the Carbon Fuel Co., of Rains, Utah, there had been no actual occurrence in the coal mines of the United States, which could be taken as positive evidence of the efficacy of rock dusting in the prevention of the propagation of coal dust explosions. The U. S. Bureau of Mines, however, had run innumerable tests under conditions which closely approximated actual coal mining conditions and had clearly shown that rock dusting was effective.

Jan 1, 1926

By Louis E. Reber

Jan 1, 1922

By M. Schussler, J. S. Brunhouse

Arc-melted and electron-beam melted tantalum in the cold-worked and the recrystallized conditions showed high strength, good tensile ductility, and excellent notch toughness down to 321°F. Arc-melted material, containing moderate amounts of interstitials, possessed better short-time strength than higher purity electron-beam melted material up to 2000°F. Cold-working substantially strengthened arc-melted tantalum, whereas electron-beam melted material exhibited a low work-hardening rate and possessed better formability characteristics. With identical compositions and microstructures, the mechanical properties of melted tantalum and uacuum-sintered tantalum should be similar. TANTALUM metal usage is increasing rapidly in a number of applications. The outstanding chemical corrosion resistance of tantalum accounts for its applications in chemical processing equipment for severe service conditions and for surgical uses in the medical field. The largest present requirements for tantalum are in the electronics industry, where its special properties are useful in capacitors. The high melting point (5425°F) and inherent ductility of tantalum also suggest that tantalum and tantalum-base alloys might offer an excellent combination of high strength at very high temperatures and good fabri-cability. Pure tantalum has been used in significant amounts in parts requiring high-temperature strength, such as heating elements, reflectors, and heat shields in high-vacuum high-temperature furnaces and in electronic tubes. A few very promising tantalum-base alloys have been developed and are being investigated extensively. The possibilities for tantalum as a high-temperature structural material, either unalloyed or alloyed, will become better defined when more extensive mechanical property data are known. pughl measured the tensile properties of vacuum-sintered tantalum in sheet form for the temperature range of 78" to 1500°K (-321' to 2240°F), and Bechtold reported data obtained at low temperatures.' Drennen3 determined creep and stress-rupture properties of both vacuum-sintered and arc-melted tantalum sheet at 1200 °F. Some additional data on the mechanical properties of tantalum at temperatures up to 5000 °F have been summarized elsewhere.4'5 It is probable that large structural shapes of tantalum, either unalloyed or alloyed, can most readily be produced from ingots prepared by melting. Consequently, the present investigation was undertaken to determine more extensive short-time mechanical properties of tantalum metal consolidated by melting. EXPERIMENTAL PROCEDURE Melting and Fabrication—Two tantalum ingots were utilized in this study to obtain information on the effect of interstitial elements on mechanical properties. Both ingots were melted from Union Carbide Metals Co. tantalum dendrites.

Jan 1, 1961

By ERJIINICI FERRARIS

1. HISTORICAL REVIEW AND INTRODUCTION. THE development of the mining industry in Sardinia dates from the application of the minim law of 1859, which, following the example of the French mining law of 1810, declared prospecting to be free, and suppressed the liens which had previously attached the mine to surface ownership. The first ore-dressing plants were installed by German engineers upon the classic models of the Harz and of Freiberg; but in 1880 Sardinia commenced to open a new path in that industry, utilizing the refuse from the mining of rich, selected minerals, of poor deposits, and of mixed ores. The first experiments were attempts to adapt the existing apparatus to local conditions, but progress was rapid, as was demonstrated already in 1887 by the calamine-dressing-mill of Monteponi, which exhibited a large plant designed in accordance with the experience gained, and constructed entirely in the machine-shops of the country, after new models and designs.1 This example was followed two years later by the Société Malfidano, with a large plant of the same sort, and with the reconstruction of the old-fashioned-dressing-mill, built in 1880 by the Austro-Belgian Company. In 1900, almost all the mines of Sardinia had adopted the new designs, and the island contained 32 concentrating-works, employing 2,000 h.p. and 1,924 workmen. Since that time, there have been added a large dressing-mill for blende at Gennamari, and two for calamine, at San Giovanni and at Masua, while the establishments at other mines have been enlarged and perfected. For the treatment of intimately mixed ores, a large establishment has been built upon the new

Jan 5, 1908

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°F.) for 15 min., cool rapidly to casting temperature, and cast.' In Germany superheating is carried out at 850' to 900°C. (1560° to I650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (I740°F.).2 In the United States superheating is carried out at 1600' to 1700°F. (871' to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.! in heavy sections and from 60 to IOO in 1/2-in. sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. Materials and Methods The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 Per cent aluminum, 2 per cent zinc, and 0.1 per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945