Search Documents

By G. G. Oberfell

THOUGH the largest volume use of natural gas has been, is. and in all probability will continue to be as a fuel for domestic and industrial heating, it has various market outlets, both as a fuel and as a raw material for the chemical industry. Natural gas is a preferred type of fuel where ease of control, fuel uniformity, and freedom from ash are of primary importance. Other industrially important uses are as a source of carbon black and as a fuel in various low-cost heating operations. Many other uses are of varying importance and new potential uses are continually being uncovered, some being of economic importance to the gas indus¬try as a whole, but most of them involve such small volumes of gas that they are only of passing interest. Since various products extracted from natural gas and recovered as by-products from petroleum refining, such as liquefied petroleum gas and fuel oil, are being utilized in many industrial and domestic heating applications, some consideration will have to be given such materials in order to present a reasonably complete story of the importance of natural gas. Some of these materials may prove to be transient competitors and will not be available when more profitable uses are found for them. Meanwhile, however, the potential volumes of such materials available, the current volumes being marketed, and the nature of the utilization are considered as constituting an essential part of the over-all fuel picture.

Jan 1, 1946

By William M. Baldwin

Jan 1, 1946

By William M. Baldwin

Jan 1, 1946

By J. G. Thompson

PROJECT 8411 of the U. S. Bureau of Standards, sponsored by the Iron and Steel Division of the A.I.M.E., is an attempt to define more concisely than has been possible heretofore the accuracy and the Limits ' of usefulness of the ' various methods now in use for the determination of oxygen as it exists in ferrous materials. It originated in correspondence between John Johnston and other metallurgists, and was brought to the attention of the Iron and Steel Division of the Institute at the Annual Meeting in February, 1933. As reported in MINING AND MET,ALLURGY, Vol. 14, page 152, March, 1933, "Dr. Johnston introduced, and those present adopted, a resolution that the Iron and Steel Division of the A.I.M.E., believing that a careful comparison of the several methods now in use for the analysis of steel for nonmetallic elements such as oxygen is highly desirable, heartily endorses the proposal that the U. S. Bureau of Standards act as a clearing house " in this matter, undertaking the final preparation and allocation of identical samples to those laboratories willing to collaborate in this important question, and collate the results re- ported back to the Bureau.'"

Jan 1, 1934

By Kermit Allen

Historically, major natural gas transmission companies have been faced with the problem of meeting peak demands when the source of natural gas is located hundreds of miles away from the marketing area. Transcontinental Gas Pipe Line Corp.'s position was further complicated when offshore gas supply wells were shut-in during hurricane alerts. Transco's solution to this problem was the construction of salt storage wells adjacent to their pipeline near Eminence, Miss. Storage caverns were constructed using conventional solution mining methods. Two 13 3/8-in.-diam cased wells were completed and a 1,000,000-bbl cavern was leached at an interval of 5700 to 6700 ft at the base of each well. The two caverns have a usable storage volume of 2.0 billion cu f t and each well has a deliverability rate of 375 million standard cfd. The caverns are unique in that brine is not used for product displacement-all brine has been removed from the caverns. Natural gas is stored at a maximum pressure of 4000 psia. During withdrawal the cavern pressure drops to a minimum of 1225 Asia-the volume of gas between these two pressures becomes "usuable or top gas." The Eminence storage terminal is located on the Eminence salt dome about 30 miles north of Hattiesburg, Miss. Construction began in July 1968 and was completed in October 1970.

Jan 1, 1972

By Laurence Delisle, Aaron Finger

THE alloys formed by the addition of nickel to iron by convelltional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.? owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect could be obtained in alloys of iron and nickel prepared by powder metallurgy technique. PROCEDURE Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, 0.001 5 ; lead, 0.035; tin, 0.025 ; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A representative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 3 2 5-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the surfaces of the particles. The reduced powders, slightly caked, were ground in a mortar and screened again through a 325- mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hydraulic presses. The pellets were compacted in a cylindrical die, ½ in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specifed for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By Orville R. Lyons

THE removal of moisture from coal has been a coal-preparation problem ever since the first wet-washing preparation plant was placed in operation. Today, when most of the coal produced in the United States is wetted at the working face when mined, or is cleaned by wet methods, the removal of moisture is a necessity for any one or a combination of the following reasons; (1) to avoid freezing difficulties during shipment, (2) to increase the B.t.u. content, (3) to effect savings in freight costs, and (4) to so improve the coal that it may be used for specific purposes-for instance, in the production of briquettes or the production of metallurgical coke-or so that it can be treated by dry cleaning methods. In general, the amount of water retained by coal particles varies with the size-consist of the coal. Fine coal has a larger surface area per unit weight than does coarse coal, so its capacity for retaining moisture is proportionately greater. The removal of moisture from coarse coal is relatively easy, while the removal of water from minus 10-mesh coal or finer is a major problem, usually requiring an individual solution at each preparation plant. As a result, a multitude of methods and a variety of equipment have been designed to solve both general and specific moisture-removal problems. Definitions In order that misunderstanding may be eliminated insofar as possible, it is necessary to define the terms to be used. The moisture content of any given increment of wet, washed coal is made up of two parts, inherent and surface moisture. Inherent moisture has been defined in various ways and as yet no standard definition has been agreed upon. However, in general, it is considered as the moisture that is present in the coal in the bed. The important point to remember is that coal with any amount of inherent moisture, whether 2 or 20 per cent, will appear dry if there is no surface moisture. Also important is the fact that inherent moisture can be removed, in part, by air drying at atmospheric temperatures. Surface moisture is that attached to the surface of the coal particles or that retained in cracks and fissures other than capillary openings in the coal substance. Essentially, insofar as the bituminous coal and anthracite indus-

Jan 1, 1950

Discussion of the paper of F. C. NEWTON, presented at the New York meeting, Feb-ruary, 1915, and printed in Bulletin No. 9S, February, 1915, pp. 473 to 477. H. 0. HOFMAN, Boston, Mass.-The results of these large-scale experiments, which were carried on at Perth Amboy, show that there are many differences between theoretical conceptions and their applications to work on a large scale. The author has given reasons why the results of bringing a desilverizing kettle to the high melting point of the zinc-silver alloy, Zn3Ag2, melting at 665° C., are not satisfactory. In all probability the alloy is dissolved in the lead; it may also be decomposed by the lead; the practical result is that this high temperature does not work. It remains now for the laboratory man to carry on systematic experiments

Jan 5, 1915

By J. F Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

IN the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1-2 results in inadequate beneficiation. INVESTIGATION OF FLOTATION METHODS Flotation has been used in Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate.3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over-all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P205 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P205, 20; Si02, 40; CaO, 29; Fe203, 2; A1203, 3; F, 2.3. The particle-

Jan 1, 1947

By G. Van Esbroeck, M. Van Weyenbergh

The copper mines of the Katanga region in the Belgian Congo lie along the same mineralized belt as those of Northern Rhodesia. There are two distinct types of deposits in that belt, the dolomitic and the quartzitic. In the dolomitic type the metallic minerals are found in a dolomitic limestone country rock. Through oxidation and enrichment, large deposits of high-grade oxidized copper ores were formed, some of which are being worked by the Union Minière du Haut Katanga. Such deposits are all in Katanga. The quartzitic deposits are found in Katanga and Northern Rhodesia. Here the primary mineralization occurred in sandstones and quartzites, in horizons stratigraphically lower than the dolomites. These rocks are not favorable to secondary enrichment and the oxidized zone is poorer than the sulphide zone, which alone contains the ore. There are also in Katanga a few ore-bearing veins. One of them is being worked in the Prince Leopold mine at Kipushi. Prince Leopold Mine The Kipushi ore body fills a fault vein and invades the wall rocks more or less extensively by metasomatic replacement. The vein strikes north-northeast and south-southwest and dips to the west. The variable dip averages 60' to a depth of 300 ft., and more uniformly 80' below 400 ft. In the upper section the average width is 200 ft. and below the width is about 150 ft. The length of the ore body is 2300 feet. The eastern side of the vein—the footwall—is dolomitic and contains irregular masses of ore sometimes extending 100 ft. or more from the main

Jan 1, 1940

By M. Van Weyenbergh, G. Van Esbroeck

The copper mines of the Katanga region in the Belgian Congo lie along the same mineralized belt as those of Northern Rhodesia. There are two distinct types of deposits in that belt, the dolomitic and the quartzitic. In the dolomitic type the metallic minerals are found in a dolomitic limestone country rock. Through oxidation and enrichment, large deposits of high-grade oxidized copper ores were formed, some of which are being worked by the Union Minière du Haut Katanga. Such deposits are all in Katanga. The quartzitic deposits are found in Katanga and Northern Rhodesia. Here the primary mineralization occurred in sandstones and quartzites, in horizons stratigraphically lower than the dolomites. These rocks are not favorable to secondary enrichment and the oxidized zone is poorer than the sulphide zone, which alone contains the ore. There are also in Katanga a few ore-bearing veins. One of them is being worked in the Prince Leopold mine at Kipushi. Prince Leopold Mine The Kipushi ore body fills a fault vein and invades the wall rocks more or less extensively by metasomatic replacement. The vein strikes north-northeast and south-southwest and dips to the west. The variable dip averages 60' to a depth of 300 ft., and more uniformly 80' below 400 ft. In the upper section the average width is 200 ft. and below the width is about 150 ft. The length of the ore body is 2300 feet. The eastern side of the vein—the footwall—is dolomitic and contains irregular masses of ore sometimes extending 100 ft. or more from the main

Jan 1, 1940

Frank Firmstone, Easton, Pa. (communication to the Secretary*) : It may not be amiss to point out that the top-pressure in iron blast-furnaces is largely affected by variations in the temperature of the gas. I find in my note-books, cases in which the pressure was from 9.25 to 9.5 in. of water when the material in the furnace was low (after dinner-hour), which fell to from 8 to 8.5 in., when the furnace was again full, and the gas consequently cooled. The chief cause for this effect is, that, at the higher temperature, there is a decrease in the weight of the gas in the descending-leg of the siphon formed by the down-comer and the chimneys. It does not seem probable that there is any direct relation between top-pressure and quantity of flue-dirt. Top-pressure, at any given moment, measures the " head " necessary to discharge the gas then passing, against the resistances of pipes, valves, etc., in the gas-conduits between the top of the furnace and the mouths of the chimneys, and can be increased at will by closing, more or less, the valves, or dampers, at the stoves and the boilers. The question of relation between top-pressure and flue-dirt can be settled very easily by direct experiment, working alternately with gas-valves open, and partly closed, and noting the top-pressures and the respective quantities of fluedirt collected. The quantities of fine ore blown away, as shown by Mr. Grammer's tables, are astonishing to one who has had no actual experience with Mesabi ore and hard driving. Flue-dirt, in the sense in which he uses the term, was unknown at anthracite furnaces so long as the working was normal; when it did occur, it was always an incident of scaffolding and bad work, and was no doubt caused by an increase in the velocity

Jan 1, 1904

By Frank W. Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength, consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig. 1 was drawn.

Jan 1, 1928

By MAURICE ALTMAYER

M Y DUTIES, as a member of the Department of Franco-American War Cooperation of the French High Commission were to study the copper and brass industries of America from the mining of the various non-ferrous metals to the semi-finished, or finished materials. In the pursuit of these studies, it was my privilege to visit a number of industries and organizations in different parts of the country. I first visited most of the Eastern copper refineries that were supplying the Allies with vast amounts of metal. These works are producing their material by the multiple or the series process, although the first method predominates. But, regardless of the process employed all the plants attain an exceptionally high standard of quality in their production. One of the points that particularly attracted attention was the manner in which improvements could be traced from the older worlds to the more recent ones. The impression was that, thanks to a spirit of broad-minded cooperation between the principals of the companies and frequent exchanges of views between members of the staffs, all persons interested benefitted by the experience thus gained, to the advantage of the community at large.

Jan 1, 1920

By C. W. Davis

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.1 The properties that make fuller's earth useful in the treatment of petroleum products by "percolation" and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other adsorbent earths.

Jan 1, 1929

By D. J. Mack, R. E. Reiswig

Six examples of the peritectoid transformation were selected from the literature and studied by the method of isothermal transformation. The kinetics and mechanisms of five of the examples are presented as TTT diagrams and photomicrographs. The exist-enc- of a peritectoid in the sixth case is doubtful. ALTHOUGH the peritectoid transformation per se has been known for many years, no precise published data exist concerning the kinetics or mechanisms involved in transformations of this type, except for the brief treatment by Rhines, et al. 1,10 Bearing in mind the fact that investigations of recent years are uncovering more and more peritectoids and suspected peritectoids, a thorough study of the well-established peritectoids appeared to be in order. It was for this reason that a study of the kinetics and morphological mechanisms of six binary peritectoids was undertaken. The six peritectoids selected from the literature for study were those reported at 7.02 wt pct Al-Ag, 26.0 wt pct Sb-Cu, 30.5 wt pct Sb-Cu, 32.3 wt pct Sn-Cu, 8.35 wt pct Si-Cu, and 21.2 wt pct Al-Cu. These selections were based on availability and purity of components, ease of preparation and heat-treatment, and estimated reliability of the available equilibrium diagrams in the regions of interest. EXPERIMENTAL PROCEDURE The alloys used in this investigation were induction melted in electrode-grade graphite and chill-cast in cast-iron split molds. In all cases, the alloys were so brittle that they could easily be broken into samples weighing 1 or 2 g. Chemical analyses showed that the alloys used were close to the respective peritectoid compositions reported in the literature and that the impurity levels were low in all cases. Metallographic examination showed uniform distributions of phases in all samples, indicating uniformity of composition in the samples studied. Isothermal transformation studies were carried out in fused-salt media, using the familiar inter-rupted-quench method. Uniformity of temperature in the salt baths was maintained by continuous stirring with a stainless-steel agitator. On the basis of actual observations of the temperature fluctuations, the estimated temperature control was + 10C for the Ag-Al and Cu-Sb alloys and ±30C for the Cu-Sn, Cu-Si, and Cu-Al alloys. The accuracy of all temperature measurements was estimated to be ±1°C. It was found necessary to mount metallographic specimens of the Ag-Al alloy in cold-curing methyl methacrylate, since the temperatures encountered in mounting in bakelite or lucite caused an appreciable degree of transformation to the ß phase. For the other alloys, wood-flour-filled bakelite mounts were used to avoid extraneous X-ray diffraction lines during the later examination of the metallographic specimens on a Norelco Geiger-counter d if f r ac tomete r. In the X-ray diffraction procedure, agreement between the published diffraction patterns and those obtained in this study was good. This was particularly important for phase identification, since the literature contained little in the way of micrograph description in some cases. Etching of the silver-aluminum alloy for metallographic examination was done by swabbing with either of the following reagents: 1) 10 g CrO3, 1 g (NH4), SO2, 0.5 g NH4NO3, 100 ml H2O, or 2) 10 ml NH4OH, 1 ml 20 pct KOH, 4 ml 3 pct H2O2, 5 ml H2O. The other alloys were etched with the usual bichromate etchant: 2 g K2Cr2O7, 1.5 g NaC1, 8 ml conc. H2SO4, 100 ml H20 (swabbed vigorously). EXPERIMENTAL RESULTS A) The Ag-Al peritectoid at 7.02 wt pct Al— The phase equilibrium involved in this peritectoid is shown in Fig. I.2 The phase boundaries in the vicinity of the peritectoid were most comprehensively established by Hume-Rothery, et al,3 who placed the equilibrium temperature at 448 °C and the equilibrium compositions of the a ß' and y phases at 6.11, 7.02, and 7.24 wt pct Al, respective The alloy used in this study analyzed4 6.95 wt pct A making it slightly hypoperitectoid according to the accepted equilibrium diagram. The rate of the transformation a+ y — ß' varies rapidly with degree of undercooling below the equilibrium temperature, passing through a maximum in the vicinity of 350°C. Thus the TTT dia-

Jan 1, 1960

By Henry M. Rowe

Professor Ruff's most illuminating paper' describing his extremely valuable investigation of the carbon-iron equilibrium diagram assigns definite temperatures to certain very important lines in the diagram, viz.: the eutectic temperature EB (Fig. 1) and the " near-eutectic " temperature E'B', but without indicating clearly enough the reasoning which warrants these assignments. These temperatures are of such primary importance that it is well to indicate the apparent gaps in the reasoning, in the hope that they may be filled in. In his diagram, Fig. 1, the point X and the liues B'D'lII represent the experimental results reached by Ruff and Goecke;a AB, AEB, and SE represent the liquidus, the solidus, and the solubility of the carbon in solid austenite in the absence of graphite according to Gutowsky,3 AB being also in accordance with Spiecker's data; S'E' the solubility of carbon in solid austenite in the presence of graphite according to Ruer and Iljin;5 GS the line A3 after Ooerens and Meyer; 6 and EBC the true eutectic line as inferred by Prof. Ruff from Gutowsky's data. B'D' is the carbon content found in cast-iron which had apparently saturated itself with carbon in the presence of the graphite of the enclosing graphite crucibles in which the determinations were made. From its straightiiess and its sharp inflection near 6.67 per cent. of carbon, the carbon content of

Jan 1, 1913

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938