Search Documents

By A. R. Gregory, A. L. Podio, K. E. Gray

Dynamic elastic properties of dry and water-saturated Green River shale samples were computed from compressional- and shear-wave velocity measurements. P- and 5-wave velocity measurements were made in three mutually perpendicular directions with respect to the bedding planes. Measurements were also made in several different directions by varying the angle between the bedding planes and the direction of propagation of the wave for angles of 0, 30, 45, 60 and 909 The oriented samples were subjected to both confining pressure and axial loads, in excess of the confining stress, in the direction of propagation. In general, P- and S-wave velocities increased with increasing stress levels, with a corresponding increase in Young's modulus. Water saturation caused the P-wave velocity to increase and the S-wave velocity to decrease. Elastic moduli decreased upon saturation, except for Pois son's ratio, which increased, indicating some degree of weakening of the material. The samples showed a moderate degree of anisotropy; this was to be expected from the laminated nature and shallow occurrence of Green River shale. INTRODUCTION This paper presents some results of an experimental determination of the elastic coefficients of anisotropic materials (in particular, finely layered rocks and minerals such as Green River shale) from measurements of dilatational and shear-ultrasonic-wave velocities. Ultrasonic techniques have been used extensively in nondestructive testing. Several methods have been proposed by Mcskimmin, 1 and some of these have been used successfully to measure ultrasonic velocities in rocks. Hughes and Cross, 2 Wyllie et al., 3 and Birch 4,5 developed pulse first-arrival techniques for the measurement of dilatational and shear velocities. Williams and Lamb 6 used the method of cancellation of a traveling wave, which was later modified by Myers et al.' and perfected by McSkimmin. 8 Although this method is highly accurate, it has not been used as widely as the pulse-transmission methods recently reported by Jamieson and Hoskins 9 King,10 and Mattaboni and Schreiber. 11 It has been common practice to use some form of crystal transducers, either quartz or ceramic, that has been cut or polarized in different directions in order to generate either compressional or shear waves. However, accurate determination of shear wave velocities has been difficult due to problems that arise in obtaining a pure shear wave from cross-polarized crystals, which usually also generate a small amount of compressional energy. As reported by Gregory, 12 this energy can be seen as a long precursor preceding the sharp break of the shear first arrival. The need for generating pure shear waves led to interest in mode-conversion techniques, which are based upon conversion of the mode of vibration through wave reflection or refraction at a discontinuity. Arenberg13 showed that for certain materials and for certain angles of incidence it is possible to generate pure shear modes by reflection at a boundary. Jamieson and Hoskins 9 used a pyrex glass-air interface for generating pure shear waves, and King 10 used this method successfully for measuring shear-wave velocities in rocks. Gregory l4 arrived at a similar result by refraction of a wave at an aluminum-oil interface. A plane compressional wave, traveling in the oil phase, is incident on the aluminum at an angle larger than the critical angle for compressional waves, and thereby generates a purely transverse, plane-polarized wave in the aluminum. During the last few years methods have been developed that allow the simultaneous determination of shear and compressional velocities in solids.

Jan 1, 1969

By J. E. Korski

Quebec Cartier Mining Co. operates a low-grade iron ore deposit at Lac Jeannine, Que., which is located at the extreme southwestern end of the Quebec-Labrador Trough (Fig. 1). The facilities there include one of the world's largest concentrators, a hydroelectric plant of 60,000 hp, and the modern town of Gagnon. A 191-mile railway connects the mine to the seaport situated at Port Cartier on the St. Lawrence River. The harbor in Port Cartier can accommodate both lake and large ocean- going vessels and is also the site of a major grain terminal. The concentrator in Lac Jeannine is designed to produce some 8 million tpy (tons per year) of specular hematite concentrate, containing 66% Fe, from approximately 20 million tons of crude ore. An annual stripping program of 5 to 8 million cu yd of waste rock uncovers the required ore. Approximately 100,000 tons of ore and waste are removed daily on a year-round, 24-hr-per-day basis. The open pit covers an area with maximum dimensions of 8,000 x 2,600 ft (Fig. 2). Present mining plans call for an ultimate depth of approximately 1,000 ft below original ground level. The rocks in the pit area are typical of this portion of the Grenville geological province. They consist largely of marble, quartz rock, pegmatite, iron formation, and stratigraphically older gneisses. The iron-ore formation consists of medium to coarse-grained specular hematite in a quartz host rock. The formation occurs locally in a plunging, anticlinal form. The topography in the vicinity of the mine is rolling, with maximum variations in elevation of about 400 ft. The hills are thickly wooded with birch, black spruce, and some tamarack. Lakes and muskeg areas are plentiful. Precipitation and temperature records have been kept since 1959. The annual rainfall has ranged between a low of 23 in. and a high of 42 in.

Jan 1, 1969

By R. J. Schilthuis

In 1929, Coleman, Wilde, and Moore1 undertook an investigation of the theoretical decline in reservoir pressure as related to the production of oil and gas. The most important part of this work was presented in an equation defining the relationship between the reservoir pressure, the quantities of oil and gas produced, the oil and gas content of the reservoir, and the properties of the reservoir fluids. With this equation, it appeared that, with sufficient data, it would be possible to calculate the oil content of the reservoir and predict quantitatively the effect of gas-oil ratio on the decline of reservoir pressure. Needless to say, such an expression would be highly important in evaluating fields and in arriving at a choice of production methods to be used. Unfortunately, at the time these investigators published their work, there were not sufficient data available to permit application of the equation. The technique of measuring reservoir pressures had not been developed, gas measurements were uncommon, oil and water production records were in most cases inadequate, and little was known of the properties of the complex hydrocarbon mixtures making up the oil and gas in the reservoirs. For these reasons, little additional work of a similar nature could be done. However, during the past four years many data have been systematically accumulated on reservoir pressures and the properties of oil and gas, and it is now possible to use these data in furthering the studies on the behavior of oil and gas reservoirs. It is the purpose here: first, to present the derivation of a modified form of the equation given by Coleman, Wilde and Moore, which will permit the calculation of what later will be defined as the "active oil" content of a reservoir; second, to derive formulas for calculating the reservoir-energy changes that occur during the course of production, and finally, to discuss the limitations and application of the equations developed.

Jan 1, 1936

By R. J. Schilthuis

In 1929, Coleman, Wilde, and Moore1 undertook an investigation of the theoretical decline in reservoir pressure as related to the production of oil and gas. The most important part of this work was presented in an equation defining the relationship between the reservoir pressure, the quantities of oil and gas produced, the oil and gas content of the reservoir, and the properties of the reservoir fluids. With this equation, it appeared that, with sufficient data, it would be possible to calculate the oil content of the reservoir and predict quantitatively the effect of gas-oil ratio on the decline of reservoir pressure. Needless to say, such an expression would be highly important in evaluating fields and in arriving at a choice of production methods to be used. Unfortunately, at the time these investigators published their work, there were not sufficient data available to permit application of the equation. The technique of measuring reservoir pressures had not been developed, gas measurements were uncommon, oil and water production records were in most cases inadequate, and little was known of the properties of the complex hydrocarbon mixtures making up the oil and gas in the reservoirs. For these reasons, little additional work of a similar nature could be done. However, during the past four years many data have been systematically accumulated on reservoir pressures and the properties of oil and gas, and it is now possible to use these data in furthering the studies on the behavior of oil and gas reservoirs. It is the purpose here: first, to present the derivation of a modified form of the equation given by Coleman, Wilde and Moore, which will permit the calculation of what later will be defined as the "active oil" content of a reservoir; second, to derive formulas for calculating the reservoir-energy changes that occur during the course of production, and finally, to discuss the limitations and application of the equations developed.

Jan 1, 1936

By Leonard Obert

The structural stability of any mine or under- ground opening in rock is dependent on the stress field, that is, the state of stress in rock before mining, the stress distribution in the rock created by the opening, and the in situ strength of the rock. In the past mine design problems have been considered by assuming that the stress field is due only to the weight of the overlying rock, the stress around the opening can be calculated from elastic theory using laboratory-determined elastic constants, and the in situ strength of the rock can be determined from laboratory tests on small specimens. Solutions to hypothetical problems using this procedure are given in a report by Obert, Duvall, and Merrill.' Because of the uncertainties of these assumptions, this method can give only a rough approximation to the solution of actual structural problems. Obviously, this approach to determining the stability of underground openings would be greatly improved if the rock stress could be measured in situ, and it is undoubtedly for this reason that in recent years many investigators have spent considerable effort on the development of procedures for measuring rock stress. In this report a method is described for determining in situ the absolute stress in rock. The method requires the measurement of the deformation of a borehole before and after the rock is stress-relieved. The magnitude and direction of the applied stresses are calculated from the borehole deformation and modulus of elasticity of the rock. Also, the results of absolute stress determination made in the walls and pillars of underground openings in five rock types are presented. From these results a number of conclusions are drawn regarding the accuracy and limitations of this method and the problem of stress measurements in general.

Jan 8, 1962

Jan 1, 1916

By K. M. Rolls, J. Wulff, D. A. Colling

Solid-solution alloys of the Ta- Ti system containing up to 70 at. pct Ti were melted and fabricated into wire. Steady magnetic-field measurements of cold-worked wires at 4.2°K indicate that the resistive critical field increases smoothly with increasing titanium, reaching a maximum of 93 kG (J = 1 amp per sq cm) for a composition of about 50 at. pct Ti. The composition dependence of the resistive critical field indicates it is largely paramagnetically limited for alloys containing more than 35 at. pct Ti. For cold-worked wires the value of the critical current density, Jc , was found to be insensitive to composition changes for compositions in excess of 20 at. pct Ti. It was observed that Jc could be increased by final-size heat treatment at 400°C without altering the value of- the resistive critical field. Experimental data are used to calculate the electronic specific-heat coefficient and the "upper critical field" for the alloys studied. THE effect and importance of metallurgical structure on superconducting properties have been summarized by Livingston and Schadler.1 Specific work on solid-solution alloys such as Nb-zr2-7 and Nb-Ti5-7 have shown that critical current density (Jc) and superconducting transition temperature are structure-sensitive. Berlincourt et al.6,8,9 in their studies of transition-metal alloys find that Ta-Ti alloys remain superconducting at fields comparable to Nb-Ti alloys. 6,8 Transverse critical current tests of a Ta-10 at. pct Ti alloy10 and longitudinal critical current tests of a Ta-25 at. pct Ti alloy1' indicate that such alloys are capable of carrying high currents at intermediate fields (-40 kG). The work reported in the present paper was undertaken to explore the superconducting properties of further compositions in the Ta-Ti alloy system as well as the structure sensitivity of the superconducting properties. I) EXPERIMENTAL PROCEDURE Alloys were prepared by melting tantalum (Fansteel Metallurgical Corp., 99.96 pct purity) and iodide, crystal bar titanium (Foote Mineral Co., 99.92 pct purity) mixtures in an arc furnace on a water-cooled copper hearth using a tungsten electrode. Melting was accomplished in a purified, gettered argon atmosphere at pressures from 250 to 400 Torr. Each alloy was turned and remelted fourteen times to assure complete mixing of tantalum and titanium. Ex- cessive coring in the cast samples was, nevertheless, observed. This was somewhat reduced by annealing in vacuo at 1000°C for 13 hr. The ingots were then machined to 0.250 in. diam, jacketed in Type 304 stainless-steel tubing, and swaged to 0.140 in. diam. They were then drawn to 0.010-in.-diam wire. Alloys containing up to 70 at. pct Ti were readily cold-drawn to wire in this manner. Later experiments showed that oxygen additions up to -3000 ppm could also be cold-worked into wire. Test samples for superconductivity measurements in the 2-in, air-core Bitter solenoids of the M.I.T. National Magnet Laboratory were prepared from 10-in. lengths of 0.010-in.-diam wire, cleaned of residual wire-drawing lubricant. Current contacts were made by clamping clean copper tubing over both No. 18 current lead wire and the ultrasonically indium-tinned ends of the specimen wire.12 Potential leads of No. 32 copper wire were connected to the specimen by ultrasonic soldering in an indium bath. The potential lead separation was about 4 cm, corresponding to the circumference of the Bakelite rod to which the wire was affixed with half-mil Teflon tape. The final specimen configuration is shown in Fig. 1. Specimens were lowered into a liquid helium bath (4.2oK) in a double solenoid dewar and positioned so that the maximum magnetic field was oriented transverse to the wire axis of the gage section. Measurements were made by passing a current through the specimen at a preset solenoidal magnetic field. The current was increased until a 1-pv potential difference appeared across the gage section (1/4 µv per cm). At low magnetic fields, however, it was not possible to use this criterion because power-dissipation difficul-

Jan 1, 1967

By H. P. Leighly, F. C. Perkins

THERE have been several statements in the literature about the difficulty of producing single crystals of high-purity (99.99pct) by the strain-anneal method. Consequently, investigators tend to employ low-purity aluminum for their single-crystal experiments, or else resort to the Bridgman or other techniques which depend on solidification for the production of single crystals. The following paragraphs describe a solid-state method for the manufacture of single crystals of high-purity aluminum which should provide crystals with greater perfection than those formed by solidification. The starting material for this method of producing single crystals was secured from the Aluminum Corp. of America and has a purity of 99.99 pct, the balance being trace amounts of impurities. Specimens approximately 1 by 4 in. are sheared from sheet having a nominal 0.050 in. thickness. The specimens are given a preliminary anneal at 640°C for approximately 3 hr in order to remove fabrication strains and to produce an average grain size of about 1/4-in. diam. The specimens are then etched in Tucker's etchant (45 pct HC1, 15 pct HNO3, 15 pct HF and 25 pct H2O) to remove the oxide film. Critical strain is applied by wrapping each specimen about a 1 3/4 in. round and subsequently straightening it against a flat surface. The high-purity aluminum sheet is sufficiently soft that this operation can be accomplished by ordinary finger pressure. The specimens are immediately annealed again at 640°C for 3 hr and reetched for examination. Ordinarily, considerable growth of certain of the grains will have occurred, and occasionally a single crystal will be produced on the first attempt. The procedure of alternately straining, annealing and etching is repeated until the majority of a batch of specimens contains usable crystal sizes. Typical examples are illustrated in Fig. 1. The greatest changes in crystal sizes are produced in the initial treatments. As the average crystal sizes get coarser in the later treatments, the sever- ity of the strain must be increased in order to produce grain boundary- migration. This increase in severity is effected by decreasing the diameter of the round used for straining (to 1 1/2 in., for example) and/or wrapping the specimens about the round twice, with opposite faces in contact with the round, before flattening. Usually the strain treatments described are not severe enough to produce nucleation in coarse grain high-purity aluminum. The growth of grains occurs by strain-induced grain-boundary migration. It has been observed that the grain boundaries move most readily during the first hour or so of each annealing treatment and that the rate of movement decreases with extended holding times at temperature. Prolonged annealing treatments are therefore not usually beneficial. Similarly, the rate of growth of each crystal appears to depend upon the orientation of the crystal with relation to those of its neighbors. Frequently island grains are formed after the initial heat treatment as the result of slow grain-boundary migration. These sometime become stationary during later heat treatments. Twin orientation interfaces are frequently developed during annealing. These imperfections can usually be removed by increasing the severity of strain to produce actual nucleation of new grains of more favorable orientation at the imperfection interfaces. The largest single crystals produced in our laboratory by the above method measured 4 by 1 by 0.050 in. Examination of Laue back-reflection patterns from a limited area of the specimens, gave no evidence of polygonization. Probably there is some indication of polygonization in the original grain area provided a more sensitive technique is used for detection. Experiments to produce wider specimens were less successful, possibly because wider sheets increase the complexity of the strains induced by deformation and promote widespread nucleation. Grain boundary migration occurs preferentially in a direction parallel to the longitudinal axis of the specimen. The choice of specimen geometry with respect to the rolling direction of the sheet appears to be immaterial in regard to the production of single crystals.

Jan 1, 1961

By C. S. Matthews, H. M. Girner, C. D. Williams, M. J. Edwardson, H. R. Parkison

Quantitative interpretation of electric logs requires knowledge of formation temperature. In this paper, methods are developed for computing changes in formation temperature caused by circulation of mud during drilling operations. The basis of the method is the mathematical solution of the differential equation of heat conduction. The solution of this equation is presented in a series of graphs. These graphs are used to determine formation temperature disturbance at various radii for arbitrary mud circulation histories. Example comparisons with field results show reasonable agreement. It is concluded that, in general, the temperature disturbances caused by circulating mud are small beyond 10 ft from the wellbore but are quite significant near the wellbore. INTRODUCTION Quantitative interpretation of electric logs requires knowledge of the formation temperature in order to establish the resistivity of the formation water with accuracy. To determine the formation temperature, the temperature disturbances produced by circulating drilling mud must be evaluated. -The objective of this investigation was to develop a method for the numerical determination of these temperature disturbances at any distance from the wellbore as a function of time. The first step was to solve the differential equation describing the temperature behavior in the formation during and after mud circulation. This solution was used to calculate a series of curves relating temperature disturbance to shut-in time for various circulating periods. An "exact" method for computing formation temperatures with the use of these temperature-disturbance plots is described, and the results of an application of this method to a well in Montana are presented. Procedures for approximating formation temperatures are also discussed. BASIC EQUATIONS AND ASSUMPTIONS With the assumptions that (1) cylindrical symmetry exists, with the borehole as the axis, (2) heat flow is 1. The formation can be treated as though it is radially infinite and homogeneous in extent, as regards heat flow. 2. The presence of mud cake can be disregarded. 3. The effect of heat generated by bit action is negligible. 4. After mud circulation ceases, the rate of radial heat flow at the wellbore is negligible and is assumed zero for purposes of calculating temperature change with time. These assumptions are believed to be reasonable because of the agreement achieved between calculated and measured borehole temperature in a well, to be discussed later. Further, the agreement at the wellbore indicates that temperatures in the formation were also approximately correct. since it is the formation temperatures that determine wellbore temperature after ceasing circulations SOLUTION OF THE DIFFERENTIAL EQUATION AND ITS APPLICATION The solution of Eq. 2 for the temperature behavior during and after a single period of mud circulation is

By W. H. Emmons

MANY mineral veins occupy faults, and movements on certain warped fault planes have resulted in openings. On normal faults the [ ] steeper parts have the widest openings, and on reverse faults the flatter parts have the widest openings. Theoretically the width of the opening is the sine of the angle of deflection times the amount of movement on the fault plane, but actually the widths of some of the openings are probably less because of readjustments of walls along joints or of other readjustments. The first treatment of the subject seems to have been in a book on mineral veins by John Leithart, published in Newcastle, England, in 1838. Later the subject was treated in various texts published in Germany, in England, and elsewhere. The subject was not given much prominence in the earlier American literature on economic geology, but has interested several workers in that field in the past decade. In this paper examples of districts showing ore shoots on warped faults, with relations noted, are described. Fault veins of the three depth classes of veins are noted. Many epithermal veins are in normal faults, and commonly the larger ore shoots are in their steeper portions. Many mesothermal veins are in reverse faults and many others are in normal faults. The flatter parts of veins in reverse faults are commonly wider than the steeper parts, although they are not always as rich as the steeper segments of the veins. There are not many hypothermal veins in faults of measured displacement.

Jan 1, 1943

By N. O. Johnson, J. Boyer, D. H. Sargent, R. B. Frahme

Although the Western bentonite industry has grown rapidly, it is facing major challenges to sustained growth. The fundamental penalty of costly overland transportation to both domestic markets and to US seaports is of increasing importance; as both substitute materials and foreign bentonites present more formidable competition in the historic market areas of drilling muds, foundry sands, and iron ore pelletizing; and as foreign demand grows more rapidly than domestic demand. The Western bentonite industry is facing these challenges by altering its transportation patterns, by upgrading of products, and by emphasizing customer service and stringent quality control.

Jan 9, 1979

By John V. Beall

There was optimism on 14th Street on April 22, Earth Day. We only have the report second hand because the demonstration conflicted with another appointment. Fifth Avenue was closed to vehicular traffic from 14th Street to the Park for a few hours and the crowd that showed up to promenade rivaled anything that can be imagined, even one at a country fair in Merry Old England. Certainly the domestic animals were there and the costumes were wild-as they are almost any day on 5th Avenue. However, the mood was friendly, happy and optimistic according to one of our neighbors who filmed and taped interviews with some of the characters. People think the air is going to be clean, and the water pure in the future. Land is going to be treated with respect. Even if the demonstration temporarily fouled the streets with litter, it served the purpose of dramatizing awareness. In talking to our friend about his experiences we didn't miss the opportunity to sound out his impression of whether or not people recognize that no group of people nor industry has a monopoly on pollution.

Jan 1, 1970

By O. O. Laudig

It is a well-established fact that some ores do not reduce as readily in the furnace as others, thus seriously affecting out-put, and consequently, cost of product. With the object of obtain ing some information upon this subject, the following experi ments were made in the laboratory of the Buffalo Furnace Company. Efforts were made to obtain, as nearly as possible, represent ative ores from some of the most important mining districts in the United States. The ores received were from the Mesabi, Marquette, Gogebic, Menominee and Vermilion ranges of the Lake Superior district and from Southwest Virginia. Requests

Jan 1, 1897

By Mungo Park, C. Baring Horwood

This paper is intended, in the light of recent investigations, to call attention to some of the essential features of good practice in sampling and mine-valuation. Mine-sampling may be divided broadly into two classes: (1) development-sampling and cornputatioll of ore-reserves; and, (2) stope-sampling and estimation of stope-values. Development-Sampling. It is with development-sampling only that this paper deals— the term development being taken to mean the opening-up of a mine by cross-cuts, drives, connections, etc., preparatory to actual extraction of the ore for milling. In development-sampling the work of the sampler and the consequent estima-

Jan 1, 1909

By C. S. Barrett

THE crystal imperfections known as faults in stacking (stacking disorder) are of importance to both fundamental and applied science and are receiving increasing attention. On the theoretical side there have been recent advances in the analysis of diffraction patterns in terms of stacking faults, and on the experimental side it has been found that certain metals develop a faulted structure on cooling through a phase transformation. Beyond this, little is known of what may be called the physical and mechanical metallurgy of faulting, although there has been no lack of discussion and conjecture as to the presence of faults in metals and the effect of faults on mechanical properties and microstructures. In the close-packed metals the nature of faults can be described very simply. Face-centered cubic (FCC) crystals consist of close-packed layers of atoms, (111) planes, stacked above each other in a definite manner. If one layer is designated as the A layer, the next must be a B or a C layer; that is, every atom of the second layer lies not above the atoms of the A layer, but nestles in the hollows between these, using the hollows designated as the B positions, or the equivalent hollows designated as C. If the sequence of layers is ABCABC...., so that layers three spacings apart are directly over each other, the crystal is FCC; if CBACBA ... it is an FCC crystal that is a twin of the former; if ABAB........or BCBC..it is hexagonal close-packed (HCP). A fault is a break in the sequence, such as ABCABABC .. . which has the effect of inserting an HCP lamella into an FCC crystal. Regularly spaced faults spaced two layers apart would convert an FCC crystal entirely to HCP, or an HCP to FCC. A fault in an FCC crystal is also equivalent to creating an FCC twin of minimum thickness; in fact, the entire crystal would be converted to its twin if faults were introduced regularly. (In HCP crystals, however, twinning does not occur on the basal plane and a fault on this plane is not identical with a thin twin). Faults are one of the possible causes for annealing twins,' for the strain markings that are brought out by etching deformed metal,'," for the altered X ray reflecting power of metal at slip bands that is revealed in X ray reflection micrographs,' for the extinction of Kikuchi lines in electron diffraction patterns, and for the hardening of latent slip planes.' Since other explanations of these effects are also available," there has been no direct proof of faults from deformation; yet it has appeared likely that they would occur. Faults resulting from phase transformations in metals, however, have been clearly revealed by diffraction in cobalt" and lithium. It is to be expected that the faulting tendency is greatest

Jan 1, 1951

By Henry F. Hebley

This paper brings within the compass of one comparatively brief article a general description of the situation concerning the nation's water resources. It touches upon the phenomenal growth in the demand for water supply and emphasizes the problems facing the coal industry both with regard to acid mine water drainage discharged from active and abandoned mines and the suspended solids discharged to the stream system from wet coal preparation plants.

Jan 4, 1953

By Guillermo Hileman

In March the President approved the new oil bill, .which became effective as Law No. 12161, providing among other things a contribution or tax on all producers varying from 8 to 12 per cent payable monthly. The new regulations, for chapter VI bearing on the tax feature, of this

Jan 1, 1936

By Guillermo Hileman

In March the President approved the new oil bill, .which became effective as Law No. 12161, providing among other things a contribution or tax on all producers varying from 8 to 12 per cent payable monthly. The new regulations, for chapter VI bearing on the tax feature, of this

Jan 1, 1936

By J. Wright, R. J. Tyler

Changes in the pore structure of hematite pellets during reduction to iron were investigated under a variety of experimental conditions. Pore structures were determined by a mercury penetration technique. The reduction temperature was found to be the major influence on structure, the pore system being bimodal below 7.50°C and unimodal above 900°C. Pore sizes ranging front 0.04 to 20 m were observed in complete metabolized pellets produced over the temperature range 650 - 1050°C. Gas composition and reduction rates also influenced the pore structure of the metabolized pellets, although to a lesser extent than the reduction temperature. An apparent activation energy of 24 kcal/mole was derived for the pore formation process.

Jan 1, 1979

By H. W. Paxton, C. C. Busby

IT has been shown previously' that strain aging can markedly improve the tensile properties of low carbon martensites, especially the yield-tensile ratio, without seriously affecting the ductility. In view of interest in high strength steels, an investigation has been made of the effect of strain aging following tension or rolling on the tensile properties of A1S1 4340 in an attempt to obtain a tensile

Jan 1, 1957