Search Documents

By Sandip K. Mitra, John E. Dorn

The Basinki-modified Seeger equation for deformation of metals by means of thermally activated intersection of dislocations was used to ascertain the various factors responsible for the strain hardening of poly crystalline aluminum and a series of a solid solutions of magnesium in aluminum. The analyses were based principally on the rate of change of strain rate with stress and the Cottrell-Stokes ratio. From measurements of these quantities on a series of strain-hardened states, the force displacement diagram for intersection, the density of dislocations in the entanglements, and the contributions of the athermal local stress and long-range stress interactions were deduced. Poly crystalline aluminum was observed to have the same force-displacement diagram for intersection as single aluminum crystals, and the corresponding diagram for the magnesium alloys differed in a manner that suggested that small amounts of magnesium may decrease slightly the stacking fault energy of aluminum. Although poly crystalline aluminum had about the same initial density of dislocations as the single crystals, the density of dislocations increased much more rapidly with strain in the polycrystals. This factor and the higher back stresses generated in the poly crystalline aluminum were the major factors responsible for the higher strength of the poly crystalline aluminum, As the magnesium content of the alloys was increased, the initial density of the dislocations also increased. Most of the alloy strengthening arose from this factor; alloying effects due to short-range order strengthening, Suzuki locking, Cottrell pinning, and so forth, were estimated to be quite small. The gveater rate of strain hardening in the alloys was deduced to be due primarily to the greater increase in the density of the dislocations with strain as the magnesium content was increased. It is the purpose of the present investigation to shed additional light on the average plastic behavior of a grain in a polycrystalline aggregate, by analyses, based on dislocation theory, of appropriate experimental test results. These deductions when compared with those from single-crystal data will then serve to illustrate the major items of difference between the plastic behavior of single crystals and the average behavior of a grain in a

Jan 1, 1963

By H. S. Munroe

THE native copper of Lake Superior occurs in the form of fine grains and scales, disseminated in small percentage through the copper-bearing rock ; and in large and small masses, from a few pounds to several hundred tons in weight. Formerly the bulk of the copper came from the mines of Ontonagon and Keweenaw counties, producing mass copper. At present these mines furnish less than one-tenth of the total product, and fully one-half of this is from a single mine. The masses are usually found irregularly distributed in nearly vertical fissure veins, and require much dead work in sinking, drifting, and stoping for their development. The risk and expense attending the working of these mines have made them, with few exceptions, anything but profitable. * Read at the Montreal meeting, September, 1880.

Jan 1, 1880

By D. D. Pollock, D. I. Finch

Relationships between the compositions of specially prepared manganin-type alloys and some of their electrical properties have been established. Empirical equations, based upon the electronic configurations of the alloying elements, are given which describe the resistivity, temperature coefficient, peak temperature, and thermoelectric power of Cu-Mn-Ni-Fe alloys at approximately room temperature. Calculations based upon these relationships are correlated with experimental data. SECURING suitable alloys for the construction of stable resistors, for use in precise electrical measuring devices, has been important ever since the art of electrical measurement was begun. German silver, Pt-Ag, and Platinoid are examples of some of the alloys in early use. These early alloys were un- satisfactory for one or more of the following reasons: l—insufficient stability of electrical properties with time, 2—poor reproducibility of electrical characteristics from melt to melt, 3—excessive temperature coefficients of resistance, and 4—excessive cost. Weston introduced the Cu-Mn-Fe and Cu-Mn-Ni-Fe alloys of the type now generally known as manganins. His patents are believed to represent the first disclosure of any alloy with a negative temperature coefficient of resistance. After this work, the German company, Isabellenhutte, in conjunction with Feussner and St. Lindeck, produced alloys of

Jan 1, 1957

By E. P. Jennings

Large deposits of titaniferous iron-ore occur at Caribou, an old silver-mining camp in Boulder county, Colo., 17 miles west by south of Boulder, and a few miles northwest of the tungsten-mines. Professor Regis Chauvenet1 published a part analysis of the ore many years ago, but gave no description of the wall-rock. Caribou hill, which contains both the silver-bearing veins and the iron-ore deposits, is a low dome of gabbro surrounded by the Archæan schists and gneisses of the Front range of the Rocky mountains, the peaks of which, a few miles west of Caribou, attain an elevation exceeding 12,000 ft. The gabbro stock is roughly elliptical in outline, with approximate diameters of 1 and 3 miles. The crest of the dome is 10,500 ft. above sea-level, and the town and ore-cleposits are 500 ft. lower. Outcrops of the iron-ore occur in the town and extend NW. for 2,000 ft., where they disappear under the swampy meadows of Caribou park. Portions of the deposit are covered by drift, but one continuous outcrop is 900 ft. long and from 200 to 250 ft. wide. A second deposit is 0.25 mile south of the town along the eastern slope of the hill. It is not as well defined as the north bed, but is approximately 1,000 ft. long and from 100 to 200 ft. wide. The easily disintegrated ore does not form prominent outcrops, but the outlines of the deposits are readily traced by the large amount of ore fragments that cover the ground. Trenches and pits sunk on the outcrop expose a roughly banded magnetic iron-ore, with pyroxene as the principal gangue-mineral. The Gabbro. This rock was classified in the field as a gabbro from the presence of pyroxene and striated feldspars, and for convenience the field-name will be retained.

Jan 1, 1913

By J. T. Cherry

A fundamental goal of the Plowshare Program is to predict crater dimensions when an explosive of known yield is buried at a given depth in a given medium. In this paper a technique is presented that seems to calculate adequately, from first principles, the mound and cavity growth that occur during nuclear and high-explosive cratering events. The technique features a standard, numerical approach to high- intensity stress-wave propagation coupled with a unique model of material behavior in brittle failure. A schematic of stress-wave propagation is presented in Fig. 1. The equation of motion provides a functional relation between the applied stress field and the resulting acceleration of each point in the medium. Accelerations, when allowed to act over a small time increment [A]t, produce new velocities, velocities produce displacements, displacements produce strains, and strains produce a new stress field. Time is incremented by [A]t, and the cycle is repeated. The time increment [A]t is determined by an independent stability condition which requires the increment to be smaller than the time necessary far a compressional wave to travel across the smallest zone. We assume that failure occurs in a brittle material when either the tensile strength or the maximum allowable strain energy of distortion is exceeded. When either of these two conditions is violated, the code uses the cracked equation of state to determine the stress. A preshot testing program is used to determine the consolidated and cracked equations of state. In situ properties to be determined by field logging are density and elastic velocity (compressional and shear ve-

Jan 1, 1967

By Richard Pearce

In the treatment of auriferous copper containing bismuth, I have recently observed a small quantity of a grayish-white alloy, which on examination, proved to be Bi containing in solution, as it were, a crystalline alloy of Bi and Au. This compound makes its appearance on the surface of the auriferous Cu in small globules as the latter cools. These globules are rapidly attacked by nitric acid, and fine needleshaped crystals of Bi and Au separate out. They arc insoluble even in strong nitric acid. On examination, the crystals mere found to contain : Gold, 69.94 per cent.; silver, 0.63 per cent. ; bismuth, 29.43 per cent. (No. I).* The residue is very fusible, and at a temperature considerably below its melting-point it oxidizes rapidly, changing from its original gray color to a greenish-yellow (No. 2). On melting in a crucible under flux, a bronze-colored alloy is formed that has the specific gravity 15.47—somewhat higher than the calculated specific gravity of a simple mixture of the two metals in the proportions named. Alloys of Gold and Silver.—In following out my investigations by repeated examinations of this alloy formed at different times, I found that, in dissolving a miscellaneous lot of the alloy in nitric acid, some gold-yellow crystals were formed, which I succeeded in separating from the BiAu alloy by washing. These yellow crystals, under the microscope, showed distinct, regular, octahedral faces, and on examination they were found to be a crystalline alloy of Au and

Jan 1, 1885

By W. Scott Dunbar

INTRODUCTION Methods of linking boundary integral (BI) solutions with finite element (FE) solutions have been well described theoretically in other publications (e.g., Zienkiewicz, et al., 1977). The purpose of this paper is to point out some practical aspects of implementing these linkage algorithms for rock mechanics applications and to describe an alternative linkage algorithm. A not so obvious motivation for using FE-BI linkages is illustrated in Figure 1. The cost of modeling the excavation of the crusher station by the BI method can equal or exceed the cost of an equivalent FE model. This is due to the large surface area which must be modeled by the BI method. In such cases, a more economical approach might be to model the region immediately adjacent to the crusher station by finite elements and link the solution at the periphery of the FE model with a solution for the exterior region. Further economies can be realized if some flexibility in the type of exterior solution is possible. For example, it would be desirable to use a coarse discretization of the FE-BI interface for a BI solution, which would be less demanding of computer storage and time, or to use an analytical solution for the exterior region. The alternative linkage algorithm to be discussed allows such flexibility. BOUNDARY INTEGRAL METHODS There are basically two formulations of BI methods: the direct and the indirect. FE-BI linkage algorithms depend on which formulation is used. The purpose of this section is to briefly describe each method.

Jan 1, 1982

ALASKA Established November 19, 1947 Meets fourth Monday monthly except June through August Term of office ends October Peter O Sandvik, Chairman Denny G Breaid, Vice-Chairman Douglas W Huber, Secretary-Treasurer School of Mines University of Alaska P O Box 337 College, Alaska

Jan 1, 1958

Jan 4, 1951

By Henry Rawdon

THE RELATION between the course, or path, of the fracture of metals and alloys, produced in service or as a result of certain laboratory tests, and the crystalline units of which such materials are composed is of utmost importance. The fracture of normal material is, in general, intracrystalline, i.e., it consists of a break across the grains rather than of a separation between them. An intercrystalline fracture indicates either that the metal is of very inferior quality or that the break occurred under very unusual conditions, e.g., at a very high temperature. The usual mechanical tests, when applied to metals of the type that breaks with an intercrystalline fracture, merely measure the coherence of adjacent grains for one another and reveal little as to the real properties of the metal itself. Even such a soft plastic substance as lead, under suitable conditions, may be rendered so weak and brittle that the metal can be easily crumbled into powder by the fingers although the constituent grains have lost none of the intrinsic properties of lead. Various erroneous explanations of this behavior of lead have appeared in the scientific literature, the change being described usually as an allotropic one. The importance, in an industrial sense, of a proper explanation of this type of the corrosion of lead justifies the description of the type of metal deterioration that follows.

Jan 2, 1920

By H. M. Howe

§ 24. Introduction.—This paper discusses the chief existing data as to the temperature, in iron-carbon alloys, of Ae3, the upper limit of the transformation range when in equilibrium, as distinguished from Ac3, the temperature at which the end of the transformation is noted in heating up, and from Ar3, that at which its beginning is noted in cooling down. The former is in fact carried above Ae3 and the latter below Ae3 by lag. I touch incidentally on the influence of manganese on Ae3 (§ 29, p. 614). The sections, tables, and illustrations are numbered consecutively with those in the accompanying papers by Howe and Levy on Determination of the Position of Ae3 in Carbon-Iron Alloys, and by Burgess, Crowe, and Rawdon on Thermal and Microscopical Examination of Professor Howe's Standard Commercial Steels, to which the present paper forms a sequel. § 25. The contradictoriness of our present evidence is shown by grouping it together in Fig. 14. For instance, both Goerens and Meyer (Series 2) and Meuthen (Series 12) used practically stationary temperature, and thus reduced the influence of lag very greatly; yet Ae3 for 0.32 carbon steel according to the former investigators is 894", but according to Meuthen it is at or below 770°, a discrepancy of 124" or more. In view of our ability to measure these high temperatures within a few degrees, the existence of such a discrepancy is as unwelcome as it seems needless. I attack the thankless task of bringing some order out of this chaos. In Part 11. (§§ 29 to 39) I consider the chief causes of error. In Part III. (§§ 40 to 48) I apply certain corrections to some of the existing data, review those data, weight them, and calculate a prob-

Jan 1, 1914

By Jonathan Ludlow, Paul J. Guay

Based on two studies that were funded by the U.S. Department of Energy, the authors provide an overview of the benefits expected from mining deeper webs on United States longwalls. The first study, completed in November 1979, identified the limits and potential gains from taking deeper webs with presently available equipment. The second on-going study discusses the conceptual design and benefits of a future system for taking very deep webs.

Jan 1, 1981

By Robert N. McIndoo, M. G. Woodle

10.5-1. Introduction. In the not-too-distant past, maintenance and the facilities for maintenance were considered a necessary evil to be given only secondary consideration in the development and planning of a surface mine operation. With the increasing sophistication of mining equipment and machinery, this concept has been replaced; and today's mine managers recognize that planning for adequate maintenance facilities is as important to a successful operation as a sound mining plan. This chapter will present the basic maintenance facilities and the fundamental considerations necessary to meet the varied requirements of surface mining. 10.5-2. Determination of Shop Facilities. The size, shape, and extent of maintenance facilities are contingent on the general mining plan, the location relative to outside facilities, and to the available capital. The type of construction employed is dependent on climatic conditions and preference. HAULAGE SYSTEMS. The type of haulage equipment used will dictate the kind of shops needed. Truck haulage requires entirely different facilities than rail haulage. Some mines will employ both systems, and can include hoists, skips, or conveyor belts in combination with locomotives or trucks. The requirements of each type will be discussed. MAINTENANCE ORGANIZATION. The pre-planning decision as to centralized maintenance vs. area maintenance, or a combination of both, will greatly affect the maintenance facilities required. A single pit with relatively short travel from shops to pit will probably have a centralized maintenance system. Where more than one mine is involved, or where there are diversified sections or functions in a mine (mine equipment, mill, conveyor, or

Jan 1, 1968

By F. R. Hewitt

THE methods of mining talc are simple, and in western North Carolina are almost entirely by open cut and quarry. The larger part of the talc of this section lies in various-sized "veins" inclosed in quartzitic walls, the majority of which have by folding been thrown into a perpendicular position, or nearly so, and the exposed edges of which have been covered by debris from erosion of the mountain above. This covering of loose rocks and earth is from 5 to 25 ft. thick, and in most cases has to be removed because it is difficult to support. Sometimes the covering is heavy enough to "catch" and timber successfully, and in this case the talc can be worked out by the usual method of following the "vein," using stulls for holding up the walls until the vein is worked out, and then allowing the cut or drift to fall in. In some cases it proves more convenient to sink shafts and run drifts, following the talc "veins" until exhausted. The talc deposits of this section are badly broken and faulted both laterally and perpendicularly, and in some cases are found many feet below the level of drainage, necessitating pumping at considerable expense. . My own experience in mining talc has been that the chief point is to get a reliable "vein," and that then the mining is not as difficult, or any more so at least, than that of any common ore. If the. "veins" are pure talc it is simple; if the talc is admixed with foreign matter, such as tremolite in excess, or stains of iron or manganese, as is often the case, one had better abandon the deposit.

Jan 8, 1916

By Lawrence B. Wright

THE Republic district, Washington, is of new interest because of the discovery of new gold-silver ore within a unique structural pattern. The camp was revived in 1937 following installation of a plant to treat low-grade disseminated ore at Knob Hill and further stimulation followed discovery of "cross vein" breccia ores in 1939. Previous writers 1-2 ascribed the quartz veins to a latite porphyry stock, but are in disagreement as to its precise location and extent. This study leads to the conclusion that the ores have a more profound parentage linked to a broad system of thrust faults and folds, the mechanical origin of which is related to a southward trending (Sanpoil) syncline connecting with the Lewis and Clark zone of shift described by Billingsley and Locke3 in 1939. The Republic anticline and a cross anticline recumbent against Cretaceous granodiorite, and involving some 4000 ft of Eocene andesite flows and early Miocene lake beds, localize the ores, mainly along the east flank, in a series of openings simulating drag folds and steeper than the folded flows. These broad structural features no doubt reach deeply into the basement rocks, where at appropriate crossings and junctions it is suggested that heat effects gave rise to oremaking materials, including, in this instance, intrusive breccias that later were mineralized, and comprising the broader bodies of new ores. The breccia ore is seen crosscutting the earlier narrow quartz veins with a welding of the two at junction areas by a second surge of ore minerals. The ore mined and developed since 1937 equals district production from 1896 to 1937. The ores are typified by cherty quartz, adularia and some barite, with fine pyrite and marcasite, polybasite, pyrargyrite, tetrahedrite and gold. Selenium is present, possibly with gold, as a normal selenide. The disseminated ores, as well as the vein and breccia ores, are localized principally in one 500-ft flow (Knob Hill andesite), which has been traced around the crest of the low northward-plunging Republic anticline. The gold-silver ratio in the earlier narrow veins is about 1 to 4 and in the disseminated and breccia ores, 1 to 7. The latter higher silver ratio is deemed to reflect the character of the second surge of mineralization. Sills and dikes of the Columbia River (Miocene) basalt cut the folded structure and ore, thus placing the mineralization in the middle Miocene.

Jan 1, 1947

By T. Koulomzine

The theory of the Askania mag-netometer, as well as a complete discussion of all factors influencing magnetometer readings, is very ably described by J. Wallace Joyce.1 We will assume that the reader is thoroughly familiar with this theory and we will use whenever possible the same notations for the physical values involved in the theory. On the other hand, we believe that the principal formulas of the magnetometer can be deduced much more easily by the use of differential calculus than by the methods employed by Joyce. Consequently, we are presenting herewith a resumé of the theory of the vertical magnetometer in order to determine the correct formula of the temperature coefficient which we propose to compensate. Short Theory of the Vertical Magnetometers We shall accept the following notations: m = total mass of the magnet system, in grams. g = acceleration of gravity, in dynes. a = projection on the axis of the magnet system of the distance between the axis of support and the center of gravity of the magnet system, in centimeters. h = projection on the perpendicular to the axis of the magnet system of the distance between the axis of support and the center of gravity of the magnet system, in centimeters. M = 2pL = M, magnetic moment of the magnet system. Z = vertical component of the earth's magnetic field. ? = deflection angle of the magnet system. = focal length of objective lens in the optical system S = scale reading. In a vertical magnetometer the axis of the magnet system is kept horizontal within 2". Therefore, referring to Fig 1, we see that the magnetic torque of the magnet system influenced by Z must be counterbalanced by the gravity torque. MZ cos ? = mga cos ? + mgh sin ? or dividing by cos ? MZ = mga + mgh tan ? If we now move to another magnetic station and the temperature conditions change, the values of all the variables will change also: M, a, and h under the influence of temperature. 2, both with time and space. ? and S, as a result of all the above changes. Taking increments in Eq 2 we obtain: (Mo + ?M)(Z + ?Z) = mgao + mg?a + mg(h + ?h) tan (? +??) but tan (? +??), because ? is small, can be replaced by tan ? + tan ??; in fact tan (?+ ??) = sin ?.cos ?? + cos ?.sin ??/ cos ?.cos ?? — sin ?sin ?? but sin ? sin ???0 tan (8 + ??) ? tan ? + tan ??. Fur-thermore, neglecting all terms of the equation containing two differentials becomes: or a differential and a tan ??, Eq 3

Jan 1, 1950

By J. A. Herbst, A. L. Mular

Digital simulation is defined and simulation techniques are re- viewed. Typical methodology involves the selection of models, the adjustment of raw data, the selection of a fitting strategy, the assessment of model accuracy in a statistical sense, and the development of an executive simulation structure. Simulations serve as aids for process engineers in evaluating the feasibility of a proposed flowsheet and the effect of a modification to an existing flowsheet. In addition, simulation plays an important role in off-line optimization and in the evaluation of alternative circuit control strategies. Several examples are presented to illustrate these uses for simulation including applications in crushing circuits, grinding circuits, and flotation circuits. It is the opinion of the authors that, within the next decade, mineral processing plants will be studied routinely via digital simulation during the preliminary design stage. Simulation will constitute an important component of the design decision making process.

Jan 1, 1978

By C. F. Wang

Page I. Introduction............:.............. 395 Manchuria in General ....................... 395 Pen-hsi-hu............................ 397 Pen-hsi-hu Coal & Iron Co., Ltd................... 399 I1. organization........................... 400 III. Coal Deposit........................... 402 Location..............................402 Geology............................. 403 Coal Mining...........'.................. 404 Mining Methods........................407 Mining Cost.........................408 IV. Coal Washing Plant.......................408 V. Coking Plant..........................410 VI. Iron Deposit...........................413 Magnetite Belt.......................... 413 Origin of Deposit......................... 414 Iron Mining........................... 415 VII. Concentration Plant........................ 417 VIII. Briquetting Plant.......................... 418 IX. Blast-furnace Smelting...................... 418 iNTKODtrCTION Manchuria in General Manchuria. called the "Three Eastern Provinces" in Chinese. forms the northeastern corner of China and is bordered by Siberia on the north and northeast. and by Korea on the east. It is a land famous in Chinese annals as the place of origin of the Ching dynasty. and in more recent times it has bcen an arena for diplomatic maneuvering and commercial competition between the Russians. advancing from the north. and the Japanese from the southeast. It derives its name of "three eastern provinces" from the fact that it is divided into three provinces; Hei-

Jan 1, 1918

By Edwin S. Sperry

Metals differ widely in their behavior under the cuttingtool. Some, like iron or steel, require a slow speed and light feed, a tool shaped differently from that used for other metals,

Jan 1, 1898

By H. N. Thomson

GENERAL. THE Tooele plant of the International Smelting & Refining Co. is situated at the mouth of Pine canyon, Tooele county, Utah. It is connected with the main line of the San Pedro, Los Angeles & Salt Lake railroad by the Tooele Valley railway, and is about 7 miles from Tooele Junction. Fig. 1 is a general view of the plant. FIG. 1.-TOOELE PLANT OF THE INTERNATIONAL SMELTING & REFINING Co. The copper plant has been in operation since July, 1910, and the first blast furnace at the lead plant was blown in on Feb. 29, 1912. The location of the plant was selected on sloping ground with the idea of using gravity to the fullest extent and thus keeping labor at a minimum. Practically the entire plant is constructed of steel, reinforced concrete, and brick. Bingham ores, both lead and copper, are received over the Utah Consolidated Aerial Tramway. The tram buckets, each containing

Jan 7, 1913